Supported PowerEdge 2850 WinPE versions

Similar Questions

• A Dell PowerEdge 2850 server is used for the new ESXi server, but it does not support the 64-bit VM.

  A Dell PowerEdge 2850 server is used for the new ESXi server, but it does not support the 64-bit VM.

  I can't believe it.

  When I start up a virtual computer, it gives a wrong message shown in the picture below.

  Does anyone have any ideas on this?

  Usually not enabled virtualization technology in host BIOS.

  Take a look at can not power on a 64-bit Windows VM

• Dell Poweredge 2850 and ESXi 4.1

  I have a Dell PowerEdge 2850 with 12 GB of RAM and two CPUs, hyperthreading with 350 GB of disk space.

  This box was initially installed with Redhat Linux ES 5.4 64-bit and OS 64 bit CentOS 5.5 with no problems, so I know the processor supports 64-bit.

  I then installed VMWare ESXi version 4.1 on the Dell Poweredge 2850 with no problems.

  Then, I created a few instances VM I want to install CentOS 5.5 64 bit.  During the installation of a VMware instance, I get this:

  msg.cpuid.notLongmodeQuestionFmt:This veritual is configured for 64-bit operating systems.
  However, the 64-bit mode is not possible.
  Longmode is disabled for this virtual machine.
  For more information, see http://VMware.com/info?id=152
  Continue without 64 bit support?

  Now the question I have is this: given that VMWare is problems with 64-bit OSes comments, how is it that I can install CentOS 5.5 64 bit on this Dell PowerEdge 2850 with no problems.  It seems obvious to me that the PowerEdge 2850 works well with the 64 bit OS but not ESXi 4.1.

  How can I get around this?

  Comments?  Thanks in advance.

  The dell series 8 (1850/2850) have no vt support, so not support 64-bit virtual machine, except 6850.

  The output of the processor shows the same thing, or rather, what he shows no vt in its ability.  It shows lm, long mode, so you can run 64-bit, that you are running ESX, but to succeed in this 64-bit support, you need the lm, you and vt, which you don't have.

  -KjB

• Dell PowerEdge 2850 does not start on a CD of ESXi 3.5

  Hello...

  I have a Dell PowerEdge 2850, who does not start on a CD of VMware ESXi 3.5.  The server works very well with Windows 2000 server.  My first thought to solve this problem was the BIOS.  This is all what I've updated in what concerns the firmware on the box today.

  BIOS - A07

  Perc4e/Di - 5B2D, A19

  BMC Firmware - 1.83, A10

  Here are the latest versions of firmware available from Dell on this box.  The machine starts to start the machine.  But all I see is the first line of text of the CD which is the following:

  ISOLinux 3.63 2008-04-10 Copyright (C) 1994-2008 h. Peter Anvin

  My next thought was that there was something wrong with the ISO image that I downloaded.  I tested it on another machine; has worked like a champ.  Now, I read on a few different posts within the VMware communities that some people have had luck with this question and others did not.

  The inventory number of Dell on the machine is 6HDGS81

  Any advice would be greatly appreciated.

  Some of the Dell CD-ROM may be little flighty. I had hard time to install a CD earlier which worked perfectly well on another machine. I made another copy of the disc, this time burning the CD at a 4 x speed. The installation went perfectly fine afterwards.

• More old PowerEdge 2850 & ESXi?

  Hello

  We have a PowerEdge 2850 we brought back in June 2005, which came with Windows 2003 Standard installed. Now, we would like to make use of additional memory that the 2850 can take up to 16GB. Of course Windows 2003 Standard does not accept this, then we are looking at the formatting, and install ESX or ESXi, then we can install Win2003 on a virtual machine.

  However, after the President of Dell support, they said it maybe some hardware compatibility problems, like 2005 it was at the beginning of when Dell began to supprt virtualization and the 2850 would be the oldest machine that they Supportepar. So I need to check the documenetion Dell & ESX/ESXi to ensure compatibility.

  I was wondering if anyone here has experience with ESX/ESXi and the PowerEdge 2850, especially one since about 2005? If so, do you have questions? I've listed the material PE 2850 below, done anything out of competition as being incompatible?

  POWEREDGE 2850

  1 x CARD mounting PCI - X - 3 SLOTS PCI - X (64-BIT)

  1 x 4 GB MEMORY DDR2 SINGLE RANK (4x1Go)

  2 x XEON 3.0 GHZ/2 MB FSB800 PROCESS

  2 x Intel Pro 1000 MT NETWORK CARDS

  1 x ATI RADEON 7000 EMBEDDED

  1 x 3.5 INCH 1.44 MB of floppy DISK DRIVE

  4 x 300 GB SCSI ULTRA320 (10 000 rpm)

  1 x PERC 4DI EMBEDDED RAID OPTION (CH SINGLE)

  1 x DRIVE de DVD-ROM/CD-RW COMBO

  1 x block of power SUPPLY NON REDUNDANT

  1 x C04 MR5, edge in USING RAID 5 RAID

  Any help, advice or suggestions would be very appreciated.

  Thank you very much

  Ben

  I installed ESXi on a 2850 at present, which was since August 2005 and it works like a treat.  We cannot do any messing extra to make it work, it worked as soon as the software has been installed.

  -----

  Mark Atherton

• PowerEdge 2850 Boot on USB

  I have recently received some PowerEdge 2850 servers and need to install can I 2008 on them.  They don't have DVD players, so I made a bootable USB drive.  I was able to use the thumbdirve to install Windows on other machines, but I'm not able to get these 2850 to even attempt to boot from the USB key.

  I entered the BIOS and USB controller 'on with BIOS support.  I tried each of the three types of USB emulation available and none doesn't seem to work.  Also, I saw some web pages that describe the USB drive would seem the selection of boot sequence, but it's not.

  Any suggestions?

  Alex

  I did install it on a GROUND of 2850's and here are a few possible suggestions based on what you said or did not say in your message:

  Make sure you have the USB ports enabled embedded devices and emulation set to Auto.  In addition, make sure that you have the USB in THE SYSTEM when you start the BIOS to change the boot order.

• PowerEdge 2850 perc 4e/di has no road

  I just want to confirm before I replace the failed drive with someone who has experience. I am running openmanage have 2 virtual disks raid 1, the 1st shows two thin discs. The 2nd shows a failed drive. These are hot swappable disks and I have some records of exact replacement on-site. It seems too simple that change to the new drive and clicking on rebuild the right?

  Server always remains online during the reconstruction of the new correct player? If the performance of the server are reduced during the reconstruction could I for the day exchanging the defective drive again and then open a session remotely late into the night and click on rebuild? (I can't access it remotely, no problem there).

  Just never failed before and looking for someone who has been there and a heads-up.

  Thank you

  Youngfam,

  That is right. The server remains online. From there you remove the failed drive and then after about 20 seconds, insert the replacement. Now the raid controller should automatically start this reconstruction for you, but if not then you would need to do a manual rebuild or assign the replacement as a spare drive, resulting in its reconstruction.

  This is the manual for the Perc 4e/di - http://downloads.dell.com/Manuals/Common/dell-perc-4-di_User's%20Guide11_en-us.pdf

  It contains additional information regarding new buildings and replacing failed hard drives.

  Regarding performance, the default rebuild rate is 30%, so it affects performance a bit during the reconstruction. Not to where users would notice, unless under a heavy load.

  If you remote access to the best way to control the reconstruction, and everything would be to install Open manage server administrator on the server. It will allow you to monitor and manage the health of the server and the controller. You can get OMSA here - http://www.dell.com/support/drivers/us/en/19/DriverDetails/Product/poweredge-2850?driverId=G2WT6&osCode=WNET&fileId=2883471492&languageCode=en&categoryId=SM

  Now with installing OMSA he will call to reset, so you can schedule downtime if you want to install this package.

  Let me know if this helps and answers your questions.

• "Your operating system does not support the 64-bit version of Silverlight" when you try to install Silverlight on your computer.

  Original title: Silverlight problem

  OK, so something was wrong when I was watching Netflix and I had to uninstall Silverlight. When I tried to reinstall it, it says "your operating system does not support the 64-bit version of Silverlight". I have a 64-bit version of Vista and I use Chrome. Can anyone help? I don't want to lose to Netflix.

  OK, so something was wrong when I was watching Netflix and I had to uninstall Silverlight. When I tried to reinstall it, it says "your operating system does not support the 64-bit version of Silverlight". I have a 64-bit version of Vista and I use Chrome. Can anyone help? I don't want to lose to Netflix.

  Clean installation of silverlight and reinstall...

  How to clean a facility damaged Silverlight and then reinstall Silverlight

  http://support.Microsoft.com/kb/2608523

• I need to install Silverlight, but when I download the installer and run it, it tell me that 'your operating system does not support the 64-bit version of Silverlight.

  Silverlight installation problems

  I need to install Silverlight, but when I download the installer and run it, it tell me that 'your operating system does not support the 64-bit version of Silverlight. I have Vista Ultimate, a 64-bit system.  Help, please.

  Hello

  It's the operating system Vista Installation Forum.

  Microsoft has set up Forums to specifically to questions of Silverlight.

  They should be able to help you there.

  http://forums.Silverlight.NET/

  See you soon.

• PowerEdge 2850 message error, no display, usb devices do not work and all readers are off (a little)

  Hello! I'm here in the dell community because I'm having an error with a PowerEdge 2850 server. When I boot it all seems to work, but inspection closer both blue and yellow led on the front is off. All devices (such as a keyboard) will not turn on. Supplies seems to work perfectly well with the error led out of power and both of the Green led on the power supply on. The drives at the front lights up but then after 2 seconds the led for every hard drive goes off and then when you reconnect the drives it will be on for 2 seconds then turns off.

  I tried:

  Reset all RAM chips and CPU in the case

  Replugin all hard drives from the server

  I tried multiple monitors

  has tried just using the power supply instead of the power brick or a surge protector

  and tried to run it only out of a raid, everything ends up in the same result

  I have no idea what to do so im just going to ask the community of dell. Thank you!

  Hello.

  What is the error specific are you? Try the system at least to the POST with the following components:

  • System Board
  • Processor
  • A bar of memory in DIMM1-A or B-DIMM1
  • Power supply
  • Riser
  • Control Panel and bottom of basket (necessary only when the last power state was off. Ensure that all USB devices, including the keyboard are disconnected.

• Browsers supported oracle developer last version?

  Hello

  Please provide me a link for the browsers supported oracle developer last version.

  I searched in vain.

  is there a restriction for browsers such as 10g and IE 6 or netscape?

  or I can run it on any browser?

  -I want to use the latest version, but I don't know if there are some people here can support me with tasks or problems with it,

  because I don't know if there are many people who use it or not?

  Thank you

  Yes, there are, I think you have not simply to look properly.

  If you open the spreadsheet of certification that I pointed you to:

  http://www.Oracle.com/technetwork/es/middleware/docs/Oracle-Forms-111220certmatrix-2087910.xls?ssSourceSiteId=otnen

  and then go to the tab called 'Client', you will find information about the supported browsers.

• I get an error message from photoshop cs5 indicating that my camera model is not supported by the installed version of camera raw. and to see the raw camera for more information help documentation

  I get an error when I try to open my photos in photoshop cs5. the file seems to be a model of camera that is not supported by the installed version on camera raw, he said. Please see the documentation of camera raw for more information.

  What should I do?

  Generally help > updates can do for you and it is important to get all the updates for CS5 in.

  If it fails, update Adobe Application Manager and let me know how it goes.

  You can find the update here: other downloads

• Colud not answer your request because photoshop does not support video on this version of windows, what can I do

  Colud not answer your request because photoshop does not support video on this version of windows, what can I do

  Upgrade to a newer version of Windows, or find a program that will run on the old Windows software.

• I have PS CS5. I had a friend send me some raw images trying to open I got this message: "line seems to be a model of camera that is not supported by the installed version of camera raw. What should I do?

  I have PS CS5. I had a friend send me some raw images trying to open I got this message: "line seems to be a model of camera that is not supported by the installed version of camera raw. What should I do?

  Download the 9.1 free dng converter that should open most of the files that your friend sent you.

  Adobe - Adobe Camera Raw and DNG Converter: for Windows

  Adobe - Adobe Camera Raw and DNG Converter: for Macintosh

• Can you please put me in touch with support for the trial version of adobe acrobat pro XI that I had tried on 15 March for 30 days. I tried to cancel because the cost is too, and Acrobat Reader are good for me. I can't uninstall program.

  Can you please put me in touch with support for the trial version of adobe acrobat pro XI that I had tried on 15 March for 30 days. I tried to cancel because the cost is too, and Acrobat Reader are good for me. I can't uninstall program.

  I had to wipe my drive since then with the trouble with Apple Store without acknowledging my machine and Time Machine reloading gave complications. Can you please cancel my trial and make my money from trial.

  Hi jack gordon.

  Adobe does not charge for the 30 day trial, but it seems that you have subscribed to Acrobat Pro (as a simple app for creative cloud membership) return March 15. To cancel your subscription, please contact customer service.

  Please let us know if you have any additional questions.

  Best,

  Sara