Switching between rendering engines when running.

Similar Questions

• MAX not to kill engine when running active with analog feedback

  I just changed my engine to use analog feedback instead of encoder feedback, but now he does not kill the engine when the switch is activated. I use a PXI7358 with a servo, and a PXI6363 and PXI6221 motor. The PXI6221 reads raw gauges of a force sensor measures 6 axes, mounted on the endpoint of my linear actuator (powered by the servo motor). LabVIEW makes a calculation on the tensions of strain gauges and exits through the PXI6363 a single voltage that is proportional to the force in one of the axes. I feed the analog voltage at the entrance to axis 1 on my analog PXI7358.

  Previously, I had used an encoder for comments and whenever I came at the end of race before or back the engine would immediately cease. Now that I'm using analog feedback, the sails of the actuator throughout the limit switch and doesn't stop, even though I see the LED light up in MAX, which indicates that the limit switch is active.

  In a LabVIEW VI I can kill the engine when the limit switch becomes active, but I would like for it to transcend LabVIEW and arrive at the MAX instead. Sometimes, apparently, there is a slightly different zero voltage output by the 6363 and the actuator moves very slowly in a sense and if I'm not looking for it runs the risk of crashing on the stop, because it is not honor the status of the limit switch.

  Any suggestions? Thank you.

  Matthew,

  what you see is the expected behavior. The good news is, you can change it, but let me explain first of all, what is happening here:

  When an axis hits a limit switch, the default operation is to put an end to the axis. This means that the current value of the feedback becomes the current set point. With feedback from encoder translates a full stop of the axis, which is typically the desired behavior. With analog feedback (g. e. force) this means that the axis is trying to keep the current value of the force, which does not necessarily mean, that the axis stops.

  The solution is to stop the axis with a kill command, which sets the DAC to zero and says the line out to disable to turn off the player. You can configure the axis to stop with a kill command whenever a limit switch is activated by using "Set u32.flx" (switch Stop Type = attribute, value = 2).

  I hope this helps.

  Jochen Klier

  National Instruments

• Switch between the buttons when a widget is open

  Hello to all I am struggling with the release of the glossary widget and HTML5... I had posted this problem last week here: http://forums.adobe.com/message/5298569. Shekhar from Adobe has helped solve the problem (thanks) but not 100% optimal. So I will ask a question that can bring me satisfaction and closing

  I want to open a glossary widget with a button 'open '. When the widget is open, the Open button will change to a close"" button. Basically, the controls will be in the same place, but open widget made toggle buttons. Is it possible to do this without too much savvy programming...? Yet once, I need HTML5 output because half of my students are running courses on ipad or other handheld computers...

  Thank you

  Daniel

  Hi Lilybiri,

  Thank you. Your idea of scenario 4 worked perfectly. A small problem that I'm starting to wonder if I'm doing something which is apparently not related... I still don't see my glossary pop up in HTML5... However, the toggle function works perfectly when using the F4/F12. Button is a large spacesaver and thanks for the idea. Do you have ideas on the exit of HTML5...? Once again, thanks a lot!

  Dan

• Can I put in rendering quality when running?

  I'm trying to "zoom" animation, but the complexity of the scene (> 4000 lines) means I only make get around 10 images per second on 'high '. Is there a way to programmatically set the 'low' quality while zooming in, then set it high later?
  

  Sure - at the beginning of your zoom,.

  _quality = "LOW";

  and at the end:

  _quality = "HIGH";

  --
  -------------------------------
  Remove "_spamkiller_" at the post office
  -------------------------------

• How to switch rendering engines?

  I have an application based on the web that is specific to my company. When I run the analysis I have to switch to get it, the renderers to display correctly. Before I did the update today, I used to right click on the tab and choose "Switch rendering engines", then run it. But now that the option is gone when you right-click. I hunted around everywhere to find it, but can not, please let me know as soon as POSSIBLE how to access this feature. Must be able to run to make it work.

  Thank you
  Amy

  Hello
  Thank you. I found it. It is an add-on in the tools. I thought about it and correct it.

  Amy

• Script for random switch between different waveforms

  Hello.

  How correctly to write the script to switch between different waveforms when generating?

  For example:
  We use the niFgen allocate named Waveform VI to allocate three waveforms. When you run the generator, the first forms of wave of work. Then the generator is activated and used in the following waveforms only second and third.

  Or, we have configured 10 waveformsand by train to spend no fixed cyclically between everyone, but only between 2 and 5 waveforms.

  If it is possible to achieve?

  Max O.

  Developer of software and engineering,

  TeSLa.

  Hi Max,.

  Each stage needs, too.  End ifs should take place at the end.  For example:

  If scriptTrigger0
  
      generate a myWfm0
  
  on the other
  
      If scriptTrigger1
  
          generate a myWfm1
  
      on the other
  
          If scriptTrigger2
  
              generate a myWfm2
  
          on the other
  
              / etc...
  
          end if
  
      end if
  
  end if

  Of course, it must all be encapsulated in a repeated structure to continue checking for triggers.

  Kind regards

• Switching between the screws in the secondary

  I have trouble getting a test program to work. I created two screws (test1 and test 2) what to do simple tasks (such as counting or turn on a Boolean value). I'm trying to switch between the two screws through a primary school in VI. I would like to run the two screws when she is called, and then switch between them while they run. However, I was making mistakes and I am at a loss to know what to do. Screws are attached.

  One of the errors I get is that of VI references are not valid, and I don't know how to solve this problem.

  OI, I'm having a few problems this morning.  Try this vi.

• Automatic switch between (WAN/LAN-WIFI)

  Hello

  Does anyone who knows how can I set up an auto switch between LAN and WIFI? My concern is to automate switching between the two when I plug the ethernet cable or unplug it. For some laptop models, we can set an option in the bios that are "Lan/Wan switching" but I can't find it on Lenovo X 1 model.

  Thanks for your time

  Pat

  Access connection does what it takes, as shown

  

  

• I want to run a vi that has a switch that passes between when run in vi It gives meeesage the highest level VI stopped for the unknown

  I want to run a vi that has a switch that passes between when run in vi It gives meeesage the highest level VI stopped for the unknown

  What should do?

  bisso92,

  You must be more specific...  When you say that you want the cover to be visible when it is called, I suspect you mean sub - vi.  You can go to the menu:

  File > properties VI then select the appearance of the window, followed to customize and select "display panel when called.  You can also select close thereafter, while initially closed.

  There are other "tricks", such as the incorporation of secondary school within your main VI, in this way, you can see both.

  Normally, a hand VI (or main function in other languages), would still present so that the operator can perform other operations.  If so you should look at using a Structure of the event with a producer / arrangement of consumer, where the consumer in a loop has the case structure where the sub-vis.

  To learn more about LabVIEW, I suggest that you try to watch some of these tutorials.

• Trails of the icon when switching between desktops in the Sierra

  I noticed some display problems since the update for Sierra. I see some trails icon when switching between desktop computers as well as a line of 1px of random colors on the right side of the screen seems to be leftover pixels for the desktop switch as well.

  Here is a screenshot: https://cl.ly/hegc

  Here is a video showing the paths of the icon: https://cl.ly/hef9

  Any other light this or know how to fix? It's rather annoying.

  Thanks in advance,

  Brent

  Hello Brent Spore.

  Thank you for reaching out to the Community Support from Apple. I know how it is important to keep your Mac running properly, and I want to help him.  Whenever we see the behavior as what you described, it is a good idea to test the symptoms in a separate user in safe mode. This will help us determine if the remanence of the icon is linked to a problem with the user account or if it's a question broad system. The articles below will guide you through these steps.

  How to test a question in another account on your Mac.

  Try safe mode if your Mac does not end commissioning

  If the ghost still occurs in safe mode, then we know it is a question broad system and I would recommend backup your Mac and Mac OS re-install using recovery, as described in the articles below:
  

  Use Time Machine to back up or restore your Mac

  How do I reinstall macOS

  If the behaviour continues or if you encounter difficulties, the entire community is here to help.

  Best regards.

• Favicons repeat through tabs, behind the label text when you switch between tabs. 37.0.1 sometimes the Green scroll bar does not have too

  Please mention the attached JPEGS. When I switch between tabs, favicon image repeated behind the text. In some cases, the image of the vertical scrollbar is messed up, it cleared up when I click on it. -Does not appear to affect performance, simply annoying. Thank you!

  Please temporarily disable your Avast extension to see if it has to do with it.

  Try Firefox Mode without failure:

  Try Firefox Safe mode to see if the problem goes away. Firefox Safe mode is a troubleshooting mode that temporarily disables hardware acceleration, restores some settings and disables add-ons (extensions and themes).

  If Firefox is open, you can restart Firefox Safe mode in the Help menu:

  • Click the menu button

    

    click Help

    

    then select restart with disabled modules.

  If Firefox does not work, you can start Firefox in Mode safe as follows:

  • On Windows: Hold down the SHIFT key when you open the desktop Firefox or shortcut in the start menu.
  • On Mac: Hold the option key during the startup of Firefox.
  • On Linux: Exit Firefox, go to your Terminal and run firefox-safe-mode
    (you may need to specify the installation path of Firefox for example/usr/lib/firefox)

  When the Firefox Safe Mode window appears, select "start mode safe."

  

  If the problem is not present in Firefox Safe Mode, your problem is probably caused by an extension, theme or hardware acceleration. Please follow the steps described in the section Troubleshooting extensions, themes and problems of hardware acceleration to resolve common Firefox problems to find the cause.

  To exit safe mode of Firefox, simply close Firefox and wait a few seconds before you open Firefox for normal use again.

  When find you what is causing your problems, please let us know. This might help others with the same problem.

• Why Firefox will allow me to have several tabs, but not allow me to switch between tabs and can only watch a new tab when closing the previous?

  Everytime I open a new tab, it appears on the tab bar where it should, but if I click on it nothing happens, the tab does not open, and I can't switch between multiple tabs. The only way to get a new tab is to close one on that I am currently, and even then it will only open the next tab in the order of precedence, so I can't even choose which tab is next to see. This problem makes it impossible to use firefox as a research tool that requires quick change back and forth between pages in multiple tabs at the same time.

  Try Firefox Safe mode to see if the problem goes away. Firefox Safe mode is a troubleshooting mode that disables certain parameters, disables most Add-ons (extensions and themes).

  If Firefox is open, you can restart Firefox Safe mode in the Help menu:

  • In Firefox 29,0 and above, click on the menu button

    

    click Help

    

    then select restart with disabled modules.

  • In previous versions of Firefox, click on the Firefox button in the upper left of the Firefox window and click help (or click on help in the Menu bar, if you do not have a Firefox button) and click on restart with disabled modules.

  If Firefox is not running, you can start Firefox in Mode safe mode as follows:

  • On Windows: Hold down the SHIFT key when you open the desktop Firefox or shortcut in the start menu.
  • On Mac: Hold the option key during the startup of Firefox.
  • On Linux: Exit Firefox, go to your Terminal and run firefox-safe-mode
    (you may need to specify the installation path of Firefox for example/usr/lib/firefox)

  When the Firefox Safe Mode window appears, select "start mode safe."

  

  If the issue is not present in Firefox Safe Mode, your problem is probably caused by an extension, and you need to understand that one. Please follow the section Troubleshooting extensions, themes and problems of hardware acceleration to resolve common Firefox problems to find the cause.

  To exit safe mode of Firefox, simply close Firefox and wait a few seconds before you open Firefox for normal use again.

  When find you what is causing your problems, please let us know. This might help others with the same problem.

• Rearrange the spaces when switching between applications

  When switching between apps spaces can reorganize, which is disturbing for users with specific workflows. For example, right now I have 6 places with different applications in each, and I have these in a specific order. However, since upgrading to El Capitan, I find continues to reorganize themselves. I can reproduce this by opting for an application by opening a window in a non adjacent space. For example, I have a window open in 4-space and I am consulting a window in space 1. If I pass this request, space 4 will be moved to position 2. It always seems to move space to the next position to the right of the current space. I can reproduce this reliable either by opting for an application by using cmd - tab, or if I have multiple windows for a single application running in more than one space, using app expose.

  Djroshi,

  My office reorganise themselves once the screen saver is running can provide you with some tips to change this behavior.

  

• iMac (retina 5K, 27 inches, end of 2015) 1-2 second stops when you try to open or switch between applications

  1-2 second ago stops whenever I try to open an application or switching between applications. The animation of the application icon in the status bar at the opening of the starts, pauses for 1-2 seconds and ends before you open the application. When you click on an inactive application window it pauses for 1 to 2 seconds before making the active window. This only happens after a reboot. It takes about a day being initialized for this problem to occur.

  This does not seem like behaviour expected of such a new machine with charge card. All advice is appreciated.

  Here is my EtreCheck report:

  ***

  EtreCheck version: 2.9 (250)

  Report generated 2016-02-03 11:33:10

  Download EtreCheck from http://etrecheck.com

  Running time 01:31

  Performance: Excellent

  Click the [Support] links to help with non-Apple products.

  Click [details] for more information on this line.

  Click on the link [check files] help with unknown files.

  Problem: Computer is too slow

  Description:

  1-2 second ago stops whenever I try to open an application or switching between applications.

  Hardware Information: ⓘ

  iMac (retina 5K, 27 inches, end of 2015)

  [Data sheet] - [User Guide] - [Warranty & Service]

  iMac - model: iMac17, 1

  1 4 GHz Intel Core i7 CPU: 4 strands

  32 GB of expandable RAM - [Instructions]

  BANK 0/DIMM0

  8 GB DDR3-1867 MHz ok

  0/DIMM1 BANK

  8 GB DDR3-1867 MHz ok

  BANK 1/DIMM0

  8 GB DDR3-1867 MHz ok

  BANK 1/DIMM1

  8 GB DDR3-1867 MHz ok

  Bluetooth: Good - transfer/Airdrop2 taken in charge

  Wireless: unknown

  Video information: ⓘ

  AMD Radeon R9 M395X - VRAM: 4096 MB

  iMac 5120 x 2880

  Software: ⓘ

  OS X El Capitan 10.11.3 (15 d 21) - time since started: about one day

  Disc information: ⓘ

  SM1024G SSD APPLE disk0: (1 TB) (Solid State - TRIM: Yes)

  EFI (disk0s1) : 210 MB

  HD (disk0s3) [recovery] recovery: 650 MB

  iMac (disk1) /: 999,33 (Go 652,85 free)

  Storage of carrots: disk0s2 999.70 GB Online

  USB information: ⓘ

  Broadcom Corp. Bluetooth USB host controller.

  Apple Inc. FaceTime HD camera (built-in)

  Western Digital my passport 071D 1 TB

  EFI (disk2s1) : 210 MB

  Boot OS X (disk2s3) : 134 MB

  Backup local (DIS3) Volumes/iMac/iMac local backup: 999,51 (Go 107,33 free)

  Encrypted AES - XTS unlocked

  Storage of carrots: disk2s2 999.83 Go online

  Apple Inc. IPhone.

  Reader SuperDrive for MacBook Air Apple Inc..

  Lightning information: ⓘ

  Apple Inc. Thunderbolt_bus.

  Guardian: ⓘ

  Mac App Store and identified developers

  Unknown files: ⓘ

  /Library/LaunchAgents/com.support.com.PerUser.Nexusd.plist

  /Library/LaunchAgents/com.support.com.PerUser.Nexussrvd.plist

  2 unknown files found. [Check files]

  Kernel extensions: ⓘ

  / System/Library/Extensions

  com [no charge]. Belcarra.iokit.USBLAN_netpart (2.0.2) [Support]

  com [no charge]. Belcarra.iokit.USBLAN_usbpart (2.0.2) [Support]

  com [no charge]. RemoteControl.USBLAN.usbpart (2.0.6) [Support]

  /System/Library/Extensions/Belcarra.USBLAN_netpart.kext/contents/plugins

  [no charge] com.belcarra.IOKit.netpart.Panther (1.6.1) [Support]

  /System/Library/Extensions/Belcarra.USBLAN_usbpart.kext/contents/plugins

  [no charge] com.belcarra.IOKit.usbpart.Panther (1.6.1) [Support]

  / System/Library/extensions/remotecontrol. USBLAN_usbpart.kext/contents/plugins

  com [no charge]. RemoteControl.USBLAN.panther (1.6.1) [Support]

  Launch system officers: ⓘ

  [loading] 148 tasks Apple

  [operation] 88 tasks Apple

  Launch system demons: ⓘ

  [loading] 191 tasks Apple

  [operation] 96 tasks Apple

  Launch officers: ⓘ

  [loading] com.adobe.AAM.Updater - 1.0.plist [Support]

  [loading] com.adobe.CS5ServiceManager.plist [Support]

  [loading] com.support.com.peruser.Nexusd.plist [Support]

  [failure] com.support.com.peruser.Nexussrvd.plist [Support]

  Launch demons: ⓘ

  [loading] com.adobe.SwitchBoard.plist [Support]

  [loading] com.adobe.agsservice.plist [Support]

  [loading] com.adobe.fpsaud.plist [Support]

  [operation] com.backblaze.bzserv.plist [Support]

  [loading] com.malwarebytes.MBAMHelperTool.plist [Support]

  [loading] com.microsoft.office.licensing.helper.plist [Support]

  [operation] com.sonos.SonosLibraryServer.plist [Support]

  User launch officers: ⓘ

  [loading] com.adobe.AAM.Updater - 1.0.plist [Support]

  [failure] com.adobe.ARM. [...]. plist [Support]

  com.apple.CSConfigDotMacCert [fail]-[...] @me.com - SharedServices.Agent.plist

  [operation] com.backblaze.bzbmenu.plist [Support]

  [failure] com.google.GoogleContactSyncAgent.plist [Support]

  [loading] com.google.keystone.agent.plist [Support]

  [operation] com.spotify.webhelper.plist [Support]

  [loading] com.valvesoftware.steamclean.plist [Support]

  [operation] net .infinite - labs.SIMBLEnablerForSandboxedApps.plist [Support]

  [operation] ws.agile.1PasswordAgent.plist [Support]

  Items in user login: ⓘ

  Workflow application (/ Applications/Flux.app)

  iTunesHelper Application (/ Applications/iTunes.app/Contents/MacOS/iTunesHelper.app)

  Cinch Application (/ Applications/Cinch.app)

  Canon IJ Network Scanner Selector2 hidden Application (/ library/printers/Canon/IJScanner/utilities/Canon IJ Network scan Selector2.app)

  SizeUp Application (/ Applications/SizeUp.app)

  Dropbox application (/ Applications/Dropbox.app)

  The messages application (/ Applications/Messages.app)

  iTunes application (/ Applications/iTunes.app)

  Other applications: ⓘ

  [operation] 2BUA8C4S2C.com.agilebits.onepassword - osx-helper

  [ongoing] com.Apple.XPC.launchd.oneshot.0x10000005.EtreCheck

  [ongoing] com.getdropbox.dropbox.48992

  [ongoing] com.irradiatedsoftware.Cinch.151392

  [ongoing] com.irradiatedsoftware.SizeUp.12192

  [ongoing] jp.co.Canon.bj.scan.network.scannerselector2.90592

  jp.co.canon.bj.printer.app.MPNEX213.45792 [loading]

  [ongoing] JP.co.Canon.cijscannerregister.14112

  [ongoing] org.herf.Flux.49952

  Plug-ins Internet: ⓘ

  AdobeAAMDetect: Version: 1.0.0.0 - 10.6 [Support] SDK AdobeAAMDetect

  FlashPlayer - 10.6: Version: 20.0.0.286 - SDK 10.6 [Support]

  QuickTime Plugin: Version: unknown

  Flash Player: Version: 20.0.0.286 - SDK 10.6 [Support]

  Default browser: Version: 601 - SDK 10.11

  SharePointBrowserPlugin: Version: 14.5.8 - SDK 10.6 [Support]

  Unity Web Player: Version: UnityPlayer version 5.2.0f3 - 10.6 SDK [Support]

  Silverlight: Version: 5.1.41105.0 - SDK 10.6 [Support]

  JavaAppletPlugin: Version: update of Java 7 55 check version

  User Plug-ins internet: ⓘ

  WebEx64: Version: 1.0 - SDK 10.5 [Support]

  Web of Google Earth plugin: Version: 7.1 [Support]

  Safari extensions: ⓘ

  1Password

  Add to the list of Amazon gift

  InvisibleHand

  Little time

  PIN button

  3rd party preference panes: ⓘ

  Backblaze backup [Support]

  Flash Player [Support]

  Time Machine: ⓘ

  Skip system files: No.

  Mobile backups: OFF

  Automatic backup: YES

  Volumes to back up:

  iMac: disc size: 999,33 GB disc used: 346,49 GB

  Destinations:

  The iMac HD Gallagher family backup local [Local]

  Total size: 999,51 GB

  Total number of backups: 82

  An older backup: 27/05/15, 12:54 AM

  Last backup: 03/02/16, 10:34

  Backup disk size: too small

  Backup size 999,51 GB< (disk="" used="" 346.49="" gb="" x="">

  Top of page process CPU: ⓘ

  140% nsurlsessiond (2)

  85% launchservicesd

  78% photolibraryd

  11% cloudphotosd

  9% com.apple.photomodel

  Top of page process of memory: ⓘ

  1.70 GB kernel_task

  1.12 GB launchservicesd

  1.12 GB cloudd

  Softwareupdated 492 MB

  Photolibraryd 229 MB

  Virtual memory information: ⓘ

  6.39 GB of free RAM

  26,00 used GB RAM (18,35 GB being cached)

  8 MB Swap used

  Diagnostic information: ⓘ

  3 February 2016, 11:31:58 /Library/Logs/DiagnosticReports/launchservicesd_2016-02-03-113158_[redacted].cp u_resource.diag [details]

  / System/Library/CoreServices/launchservicesd

  3 February 2016, 11:30:22 ~/Library/Logs/DiagnosticReports/iTunes_2016-02-03-113022_[redacted].crash

  com.apple.iTunes - /Applications/iTunes.app/Contents/MacOS/iTunes

  3 February 2016, 08:18:45 /Library/Logs/DiagnosticReports/nsurlsessiond_2016-02-03-081845_[redacted].cpu_ resource.diag [details]

  / usr/libexec/nsurlsessiond

  1 February 2016, 19:53:04 self-test - spent

  Hello Agent37,

  What are your settings of Photos? Looks like you have a ton of photos regenerate and transferring to iCloud. I've seen similar reports, but I'm not a heavy user of Photos. I'll see if I can move your question on the forum Photos: Photos for Mac

• First Pro crashes when switching between applications

  Hi all

  I edit with Premiere Pro on a Mac Pro running OS X 10.10.2 cylinder (3.5 GHz 6 - Core Intel Xeon E5, 16 GB 1866 MHz DDR3 ECC, over-pants D500 3072 MB), when I connect the images with Excel, I noticed after some time switching between Excel and Premiere Pro or all the other apps, first Pro STILL crashes with the error serious.

  
  

  Project is very disappointing and frustrating that you need to open the recovery file, creating another file and have to get timecode all over again, lost a lot of time to. Expect First pro to work smoothly on a Mac Pro.

  Anyone have a similar experience or know a solution?

  Thank you

  L

  29/03/2015 07:19:23.457 com.apple.xpc.launchd [1]: (com.adobe.AdobePremierePro.66488 [4527]) Service was released due to the signal: Segfault: 11

  Here is my complete crash report:

  https://www.dropbox.com/s/08igd5s3s6evquv/Adobe%20Premiere%20PRO%20CC.txt?DL=0

  Process: Adobe Premiere Pro CC 2014 [4527]

  Path: / Applications/Adobe Premiere Pro 2014/Adobe Premiere Pro 2014.app/Contents/MacOS/Adobe first Pro 2014 CC CC CC

  ID: com.adobe.AdobePremierePro

  Version: 8.2.0 (8.2.0)

  Code type: X 86-64 (Native)

  Parent process:? [1]

  Responsible for: Adobe Premiere Pro CC 2014 [4527]

  User ID: 501

  Date/time: 07:19:22.403 2015-03-29 + 0100

  OS version: Mac OS X 10.10.2 (14-1514)

  Report Version: 11

  Anonymous UUID: D42F2CB9-98B4-C04E-E594-A17C39AC5324

  Sleep/wake UUID: B58E8A4B-751B-4568-925F-D3E9E1130B43

  Time since started awake: 13000 seconds

  Wake time: 4000 seconds

  Crashed thread: 0 dispatch queue: com.apple.main - wire

  Exception type: EXC_BAD_ACCESS (SIGSEGV)

  Exception codes: KERN_INVALID_ADDRESS at 0 x 0000000000000000

  Hello world

  I dug deeper reading crash log, and discovered that the reason of my crash is primarily due to the confusion of audio output my mac has as he move from an internal speaker and speaker output and causes the crash. Since I had bought a DAC (digital-to-analog converter) and set the audio output of the DAC first and have no accidents since then. It will be useful.

  L

  ---

  Thread 0 crashed: Dispatch queue: com.apple.main - wire

  0 com.adobe.AudioSupport.framework 0x0000000103d7f8d0 ML::Device:GetNumberOfPhysicalChannels(unsigned_int,_bool) + 80

  1 com.adobe.AudioSupport.framework 0x0000000103d6adb8 ML::CoreAudioHost:PrivateInitDriver(std::basic_string____,_dvacore::utility::SmallBlockAllocator::STLAllocator_ _>_const&) + 712

  2 com.adobe.AudioSupport.framework 0x0000000103d6a18f ML::CoreAudioHost:LoadDriverPrivate(std::basic_string____,_dvacore::utility::SmallBlockAllocator::STLAllocator_ _>_const&,_bool,_bool) + 351

  3 com.adobe.AudioSupport.framework 0x0000000103d6dac1 ML::CoreAudioHost:LoadDriver(std::basic_string____,_dvacore::utility::SmallBlockAllocator::STLAllocator_ _>_const&) + 33

  4 com.adobe.AudioSupport.framework 0x0000000103d7b348 ML::CoreAudioHost::AddDependancy() + 56