SX20 with CUCM

Similar Questions

• dial the internet video SX20 with cucm

  It's a possible scenario?

  SX20 (Sip)--->---> Internet video CUCM advantage?

  Thanks in advance

  If you want to use Jabber for Windows, you just need C/E motorway. You will need the licenses of session Rich media for each simultaneous video call, you need to make to another company, such as cisco or other. No permit only required for audio/video/call within your organization. Its pretty simple IMO.

• SX20, EX90 with CUCM

  Hello

  the customer wants to buy SX20 and Ex90, and he needs information at my side, Questions:

  -Did he need a VCS? or CUCM is enogh for whom?

  -What is the version CUCM is supported for SX20, EX90?

  -How add these endpoints to CUCM?

  -regarding bandwidth, which is good the bandwitdth to make audio and video calls is very clear and quality? up to 6 Mbps?

  -What is the version for SX20 EX90 must be suppoeted with CUCM or VCS?

  Please, your answers are very important to me

  Thank you

  Hi Lkayyali,

  Please find the BW resolutions depending on requirements.

  profiles of optimal definition for system supporting 1080 p

  w288p30 w448p30 w576p30 720 p 1080 p 30 p 30

  256kbit/s normal 512kbit/s 768kbit/s 1152kbit/s 2560kbit.s

  average of 128 Kbps 384kbit/s 512kbit/s 1152 kbit/s 1920kbit/s

  128 Kbps high 256kbit/s 512kbit/s 768kbit/s 1472kbit/s

  profiles of optimal definition for system supporting 720 p 60

  w144p60 w288p60 w448p60 w576p60 720 p 60

  Normal 128kbit/s 512kbit/s 1152kbit/s 1452kbit/s 2240kbit.s

  average of 128 Kbps 384kbit/s 768kbit/s 1152 kbit/s 1920kbit/s

  128 Kbps high 256kbit/s 512kbit/s 768kbit/s 1152kbit/s

  Please feel free to rate this answer in case it is useful

• SX 20 with CUCM 8.6.1

  Hello

  I need to record 20 peripheral SX with CUCM 8.6.1, but SX 20 is not available in the list of devices!

  How can I register it?

  Regds

  $

  Hello

  CDP file will be used for the endpoint SX20 push updates of software and the package devce for the CUCM, where it must be installed separately.

  as mentioned in the document provided by Vivek:

  Installation instructions

  Note: Cisco recommends that you apply this device for a package

  maintenance window.

  Note: Packages of devices are installed on the active partition and cannot be

  uninstalled;

  Cisco recommends that you take a backup DRS prior to installation.

  For more information on how to do a proper backup, see the Recovery Guide disaster for each version of Cisco Unified Communications Manager.

  Procedure

  Note: Apply this package of device to all of your Cisco Unified Communications

  Manager servers, starting with the publication server and the TFTP server.

  Note:

  When you apply a device Package to activate the new device support, a broad cluster restart is necessary for these devices to record successfully.

  A

  Cluster - wide restart is not required when you apply a Package of device for the update of the existing firmware/media. Cisco Unified Communications Manager 8.6, you perform all software installations and upgrades by using the software update menu options. The system can load and process only the software that Cisco has approved. You may not install or use third party or Windows - software applications that you used a previous version of Cisco Unified Communications Manager.

  1 from your web browser, go to the web page of Cisco Unified Communications Administration of the operating system.

  2. in the menu of the software upgrades, select Install/Upgrade.

  3. fill in the appropriate values in the section where the software and click Next.

  4. in the available software drop-down list box, select the device package file

  Click next

  5. check that the MD5 has the correct value. Click Next.

  6. in the warning box, verify that you have selected the right firmware and

  then click on install.

  7. check that you have received a message of success.

  Note:

  If you restart the cluster, skip step 8.

  8. stop and restart the TFTP server.

  9 reset the devices concerned to upgrade the devices to the new load.

  Hope that helps

  Concerning

  KR Ravi

• Admin password of setting on the SX20 in CUCM - cannot set in peripheral CUCM

  I have CUCM 10.5.2

  SX20 with 7.3.1 code.

  CUCM successfully, SX20 is recorded. Can I change the display name, expansion etc... 'apply changes' CUCM and endpoint learns changes and seems correct. So I guess downloading properly its configuration file and the settings app.

  Device SX20 in CUCM admin page there is a section about 3/4 of the descent called "password and Admin user name"

  It seems to indicate that endpoint admin username and password can be defined in CUCM and pushed down to the endpoint.

  This does not work for me. It is not up-to-date.  Does anyone know if this is really supported?

  SX20 - adminfield.png

  

  I can put it fine directly from the web interface of the endpoint as usual.

  Looking at the Administration TC endpoints running TC7.2 on UCM 10.5.1 on pg 31, you use go by what follows in order for the endpoint to use the name of user and password specified in CUCM:

  1. Use a profile secure in CUCM
  2. Use the built in admin endpoint account
  3. Do not connect not not CUCM thanks to a fast track

  Otherwise, CUCM will count on you to specify an account with administrator privileges endpoint.

• Unity connection 8.6 Migration to 11 with CUCM 8.0

  Due to the right I'm going to intend a Migration of 8.6 connection unit to 11.0 of connection of the unit before I can improve CUCM. I am sure that the answer is Yes, but would there be problems running 11.0 of connection of the unit with CUCM 8.0.

  Nothing fancy on the face of connection of the unit, no unified messaging ect.

  New UC 11.0 should just registered the EPSC ports?

  Thank you

  Dan

  Looks like you need at least version 8.5 for the SCCP and SIP integration CUCM to be supported. Check the compatibility of connection of the unit guide below.

  http://www.Cisco.com/c/en/us/TD/docs/voice_ip_comm/connection/compatibil...

  Combinations for Cisco and unity connection Unified Communications Manager of the supported Version

  Table 22 Version combinations of supported for the connection of the unit and Cisco Unified Communications Manager

  Cisco Unity Connection	Cisco Unified Communications Manager
  8.5 and later	11.5 (1), 11.0 (1), 10.5 (2), 10.5 (1), 10.0 (1) 9.1 2, 9.1 (1), 9.0 (1), 8.6 (2), 8.6 (1), 8.5 (1)

  SIP: http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/connection/compatibil...

  -Terry

  Please note all useful posts

• Extending the SX20 with 12 x zoom camera

  Good day to all

  Can someone provide me with the pin code on necessary to extend the 12 x zoom camera control (cable network) when it connects to a SX20 with the explosion of cable

  • SX20
  • Extension cable
  • 12 x zoom camera
  • Right HDMI cable (10 m)

  Thank you!

  It's a cable right but with pins 3 & 6 step.  It would be nice if just Cree literature it in plain language, in addition to you give pinout diagrams.

• MGCP FXO does not register with CUCM on VG204XM

  I have a VG204XM running MGCP with CUCM 10.5. When the port is changed and reset him CUCM config push down to the VG204XM there is an error (it is identical to the Bug CSCtr78616 reported on a router 28xx in 2011)

  In the newspapers, I see that, once the router receives the config it tried to configure AALN/S0 / / 0 (voice-port 0/0)
  However, for some reason, it seems that the router is to convert the port to a 65535 instead of 0

  "cmapp_xml_get_interface_info: slot = 0 vic = 65535 port = 0".

  Since the port above does not exist on the router the survey attempt a mistake.

  Mar 27 18:07:59.278: % SYS-5-CONFIG_I: configured from console by console
  Mar 27 18:07:59.278: cmapp_xml_get_interface_info:
  18:07:59.278 Mar 27: =.
  Mar 27 18:07:59.278: cmapp_xml_get_interface_info: slot = 0 vic = 65535 port = 0
  18:07:59.278 Mar 27: Interface_name: AALN/S0/0
  Mar 27 18:07:59.278: controller:
  18:07:59.278 Mar 27: addr: 65535/0/0
  Mar 27 18:07:59.278: interface:
  Mar 27 18:07:59.278: voice_port: voice-port 65535/0/0
  Mar 27 18:07:59.278: dial_peer: voice dial-peer 9990655350
  Mar 27 18:07:59.278: dial_peer_port: 65535/0/0
  Mar 27 18:07:59.278:
  Mar 27 18:07:59.278: cmapp_xml_configure_router: verification of the Deleted interfaces
  Mar 27 18:07:59.278: cmapp_xml_get_intf: looking for a vdb [65535/0/0]
  Mar 27 18:07:59.278: cmapp_xml_configure_router: analog ports are ready
  Mar 27 18:07:59.278: cmapp_xml_find_corr_intf_cfg:
  Mar 27 18:07:59.278: cmapp_xml_find_corr_intf_cfg: old_cfg is NULL
  Mar 27 18:07:59.282: cmapp_xml_intf_cfg_changed:
  Mar 27 18:07:59.282: old intf configuration is null
  Mar 27 18:07:59.282: cmapp_xml_cfg_analog_intf:
  Mar 27 18:07:59.282: cmapp_mgcp_get_card_type_for_analog_intf: looking for a vdb [65535/0/0]
  Mar 27 18:07:59.294: cmapp_xml_cfg_router_intf: intf configuration: [voice-port 65535/0/0]
  Mar 27 18:07:59.294: cmapp_xml_cfg_router_intf: configuration [echo - cancel enable]
  Mar 27 18:07:59.298: % SYS-5-CONFIG_I: configured from console by console
  Mar 27 18:07:59.298: cmapp_xml_cfg_router_intf: 395 line router configuration error
  Mar 27 18:07:59.298: cmapp_xml_send_msg_to_callmgr: CMBH_MSG_CFG_ERR of sending
  Mar 27 18:07:59.298: * info ERROR: the router configuration failed: voice-port 65535/0/0
  echo - cancel enable
  end

  I have a VG224 gateways running with MGCP CUCM 10,5 and no error

  Everyone knows about this problem on VG204XM?

  Hello

  Please check

  https://Tools.Cisco.com/bugsearch/bug/CSCui83022/?reffering_site=dumpcr

  Auto config MGCP fails for VG204XM
  CSCui83022
   

  Description

• Connection of the UNIT with CUCM integration

  Hello

  Can someone please advice me on the underside, I CUCM (PUB + 1 SUB) cluster and node stand-alone 1 CUC.

  need to know the best Cisco recommended configuration

  1.0 order of AXL servers (what should we put 0 - PUB or SUB)

  2.0 tftp and order serever CUCM under port, (PUB, order SUB) group settings

  Please advice

  Thank you

  Purna

  Axl Server always be PUB and SUB.
  Pub - 0
  Sub - 1

  TFTP server must first be Sub and PUB.

  Sub - 0
  Pub - 1

  This is the best way and the recommended method to configure / integration with CUCM with connecting the unit

  Sent by Cisco Support technique iPhone App

• SX20 with third party camera

  Hi team,

  Can we connect Cisco SX20 with 3rd party camera?

  Since the SX20 12 X comes with a HDMI + power & control cable.

  Only requirement is for the video. Third party camera has a HDMI output.

  Camera controls & Device Control will be by Crestron.

  Someone Pls help on this...

  Thanks & best regards,

  Bharath

   
   
   

  As long as it is a supported resolution, it should work. Personally, I used my camcorder as an EX90 entry and it worked fine.

• SX20 with Smart Board

  Hello

  My client is looking for SX20.

  They would also like to integrate SX20 with the smart board to display the smart board for remote sites.

  My question is, if I do not include the option to dual license, going to work with the Smart Board.

  Or is it necessary to have the double display for this particular case.

  Best regards

  Titebiket

  Hi titebiket,

  Yes, you can share your screen through SX20 - but you will need to be

  (1) get a telepresence unit SYNCH

  http://www.Cisco.com/en/us/products/ps11653/index.html

  http://www.Cisco.com/en/us/docs/Telepresence/endpoint/software/synch/synch_release_note_v4-01.PDF

  Camera EOS/EOL

  (2) download the video switch video/duplicater that splits in two. In the projector cable, one cable at the entrance to the presentation of the codec.  Please note that this is not something that is officially supported by Cisco - so you won't be able to buy the switch/duplicater home.

  (3) you can try to use the SX20 and the dual display option. But I don't know if it will work properly, because I have not tested. However, I tried option 2.

  Thank you

  Marius

• 3241 GW ISDN with CUCM 10.5 or VCS

  Hi all

  What is the best practice to deploy ISDN GW 3241.

  It connects with CUCM or VCS control?

  How to connect it with CUCM or VCS?

  Kind regards

  There are some basic steps in the Quick Start Guide and there is more information on the different ways to configure it in this thread: https://supportforums.cisco.com/discussion/11580051/isdn-gw-3241-admin-config-guide

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

• SX20 with dual - can output duplicate / clone

  Hello

  I have a SX20 with dual display running s/w version TC7.3.3.

  Two monitors are connected and I put the configuration as below

  Setup > video > monitors = double

  I get the far - end and discovered on the first monitor and the second will be content presentation

  On change

  Setup > video > monitors = Single

  I get everything - Far end, near end and the presentation on the same screen

  and then the changes below

  Setup > video > SelfviewDefault modepleinecran > on

  Setup > video > SelfviewDefault OnMonitorRole > second

  Setup > video > output > HDMI 1 > MonitorRole = 1

  Setup > video > output > HDMI 2 > MonitorRole = 1

  But the situation is still the same

  Please help me to find a solution, I need to clone screens.

  Concerning

  Boily

  Well, I think I understand what you want now.

  If the monitors are the unique value you will see end, selfview and presentation all shared on the same screen.  However, if the monitors are set to dual, you see end on a screen with selfview and presentation on another.  There is now way to just see the far - end on both screens without possibility of selfview or presentation, screen share or taking a whole screen for itself, if one is active.

• Cisco C40 unsubscribe automatically with CUCM 8.6.2

  Hello

  I have Cisco C40 connected to CUCM 8.6.2.

  First, he is registered with CUCM and I was able to call on another phone C40.

  Then, C40 automatically BSW of CUCM and isn't recording with CUCM now.

  I added C40 via device-> phone-> Add new-> then selected Teleprecense C40

  C40 SW version is: 5.1.5.297625

  I joined C40 and CUCM screenshot. It shows not recorded, which proves C40 registerd at least once.

  I could make and receive calls with the C40 for a few minutes. Subsequently recorded automatically and now

  error message is status: failed

  Suggest pls.

  Rgds

  Rajesh

  Hi Renon,

  Please below changes made in the SIP settings:

  change SIP profile 1 Type at Cisco, since it is native enrolled and default transport for TCP

  * c xConfiguration SIP URI 1 profile: "[email protected] / * / "

  "

  * c xConfiguration SIP profile 1 DisplayName:

  * c xConfiguration SIP DefaultTransport 1 profile: TCP

  * c xConfiguration SIP profile 1 TlsVerify: Off

  * c xConfiguration SIP profile Type 1: Cisco

  * c xConfiguration SIP profile 1 outgoing: Off

  * c xConfiguration SIP profile 1 Proxy Discovery 1: manual

  * c xConfiguration SIP Proxy 1 address of profile 1: "172.31.131.10."

  * c xConfiguration SIP profile 1 Proxy Discovery 2: manual

  * c xConfiguration SIP Proxy 2 address of profile 1:

  * c xConfiguration SIP profile 1 Proxy Discovery 3: manual

  * c xConfiguration SIP Proxy 3 address profile 1:

  * c xConfiguration SIP profile 1 Proxy Discovery 4: manual

  * c xConfiguration SIP Proxy 4 address of profile 1:

  * c xConfiguration SIP profile 1 1 LoginName authentication:

  * c xConfiguration SIP profile 1 1 password:

• Telepresence EX60 with CUCM 8.5 - How to integrate?

  Good morning people,

  I'm building a lab with 8.5 CUCM and presence Server 8.5

  I'll install the Cisco TelePresence EX60, and I wonder how I do integration with CUCM.

  Need to install the additional server? You simply add a SIP device in CUCM?

  Can someone help me?

  Thank you

  Bruno

  Hello.

  You must have CUCM 8.6 in order to utlize the full potential of the CUCM / integration EX60. You save the unit directly to the CUCM.

  I recommend you take a look at this guide, after that you did with your laboratory update.

  http://www.Cisco.com/en/us/docs/Telepresence/endpoint/codec-c-series/TC5/administration_guide/cts_endpoint_administration_ucm86_quick_start_guide_tc50.PDF

  I have attached a screenshot showing how it should look like the description of the device.

  Thank you

  Marius