Synchronization problems Blackberry Bold 9700 with Bluetooth of Windows 7 drivers Sony Vaio SZ series

I have recently upgraded to Windows 7 with a clean reinstall on my laptop Sony VAIO VGN-SZ470N. Full specifications can be seen here: http://www.sonystyle.com/webapp/wcs/stores/servlet/ProductDisplay?catalogId=10551&storeId=10151&langId=-1&kw=vgn-sz470n/c&lp=8198552921665095013&productId=8198552921665095013#footNotes

My goal: to sync my new Blackberry Bold 9700 wireless via bluetooth using the built-in radio. Many people have had problems with this and the forums are littered with solutions that have worked for others, but I'm having no luck.

So-called: Device Manager software Blackberry won't recognize devices that are managed by Windows Native Bluetooth stack.

What I did:

Windows will automatically detect my bluetooth radio and installs the "Bluetooth USB Controller (ALPS/UGPZ6)" (hardware ID: USB\VID_044E & PID_300D & REV_1915, USB\VID_044E & PID_300D) driver. With this driver, I can go to the "add a device" with my phone in discovery mode, and the computer will not conclude it.

If I go in ' control panel-> add devices ", the Add Device Wizard window will tell me it's looking two detectable Bluetooth devices found in the range. I went into control panel of-> see devices-> UGX (which resembles a bluetooth adapter bit) and there was no "bluetooth settings option when I would right click."

After reading on the Blackberry forums that the BB only synchronizes with the Bluetooth of Windows stack, I updated my driver ALPS/UGPZ6 to "generic bluetooth adapter. The selection of this driver also installs driver for "Microsoft Bluetooth Enumerator. It also adds the bluetooth icon in the lower bar of good start near the time and date. I can now go to 'Add a device' and it will show my BB 9700. When I connect, matching Assistant is displayed on my phone and in windows. I enter a code on my blackberry and enter a code in the wizard windows. Both devices and then tell me that pairing has been successful. However, the two machines are.

Once the BB is paired, tent windows install the drivers of the two newly discovered devices, then gives me an error and States that the drivers cannot be installed. It is said that it is impossible to install two drives, both devices are listed in the device as "Bluetooth Peripheral Device" Manager (Hardware ID BTHENUM\ {426c6163-6b42-6572-7279-44736b746f70} _LOCALMFG & 000D).

In "devices and printers > Bluetooth' BB 9700 is now listed with a status of 'troubleshooting needs'." Although the devices are paired, the BB will ever show a status of connected, rather it will continue to just try to connect every two minutes or more. I can connect to my friends MacBook, but I have no idea how to test the fact that the connection works. I also noticed that in the screen 'Add features' phone bluetooth of my roommate. So, I looked for ways to resolve the missing drivers.

I found three solutions supposed for the driver installation error which has not WORKED for me.

(1) the first is to right click on the two strangers 'Bluetooth' devices in Device Manager and updated the driver in both cases to "RIM Virtual Serial V2". When you try to implement this solution, the status "needs Troubleshooting" will disappear, but blackberry Device Manager will not find the BB 9700 to add for bluetooth sync. Nothing else seems to change. Complete instructions for this solution have been listed here: http://supportforums.blackberry.com/t5/BlackBerry-Pearl-BlackBerry-8100/Need-Bluetooth-Peripheral-Device-driver-to-connect-to-8120/m-p/263541

The other way, I tried to fix the driver error problem was to remove all the listed drivers and reinstall the generic Bluetooth USB controller and the enumerator. Then I went and downloaded the Windows Mobile Device Center Driver Upgrade. For the two unknown devices labeled "Bluetooth Peripheral Device", I chose the Bluetooth radio driver > Microsoft Corporation > peripheral support Windows Mobile.  Once again, the status in devices and printers troubleshooting message > Bluetooth devices disappear, but still the Blackberry device manager can't find the phone. I found the original steps for this here: http://www.computers.nepalesemap.com/index.php?topic=3.0

(3) supposed to be the reason why the blackberry will not sync with the ALPS driver installation is because the windows bluetooth stack does recognize it not as compatible. So I uninstall the Bluetooth devices and blackberry. I restarted and the computer reinstalls the driver ALPS.

I found a solution which says to edit the c:\windows\inf\bth.inf file and add the hardware ID that is listed in the device under the ALPS HardwareID driver manager. I have add the ID of the hardware to the list of devices, but the bluetooth enumerator installs ever, and I can't access the Bluetooth settings.

Does anyone else have this problem? Can anyone help!


Hi Cptnnemo,

How do you close the computer, you have your Blackberry?  As with any Bluetooth, the device must be 3-4 FEET away from being discovered.  Please follow the instructions on the MSFT made, then try to keep your 3-4 feet away and try the discovery mode.

Mithdraug

Tags: Windows

Similar Questions

  • Synchronize the Smartphone blackBerry Bold 9700 with Desktop Manager

    I have trouble log my Bold 9700 with Desktop Manager (PC) for e-mail, my calendar and my contacts. I am on gmail and understand that I will not be able to synchronize my email, that's fine.

    Calendar and address book: I was told to click on my calendar with my menu button then Options and disconnect the wireless connection, this option does not exist at this location. Am I doing this wrong?

    Once I click on Options what happens, it's run by Tuping - painted paper - number of rows in icon - default reset settings

    Help!

    Hello and welcome to the community!

    There are two places to check (and disable), and the KB explains both:

    • KB22430 How to enable or disable syncing wireless contact with the BlackBerry Internet Service

    Good luck!

  • BlackBerry Smartphones Snycing Blackberry Bold 9700 with Contacts list in Outlook

    Hello

    I just bought a Bold 9700, and everything works well except the synchronization of Outlook contacts.

    I am also the synchronization of calendar, which works fine, but when I sync the contacts, I get the following error message ox80040Fb3

    I have the latest verson of the Blackberry user tools software and I tried to uninstall and reinstall again, but the same error comes back.

    If I only sync the contacts from the phone to Outlook then it works, but I can't sync both ways or from Outlook to the phone.  My phone is a Blackberry Pearl, I have had no problem of synchronization with Outlook.  The Version of the user tools for the Pearl Blackberry was Version 4.3, I re-installed and tried, but I still got the same error.

    I think that she must have a problem with the software on the phone, as the problem did not happen with my other Blackberry, and it happens with both versions of the software.

    I use Vista Home Premium with Office XP.  Someone at - it ideas?

    1, while that synchronize you the address book, it goes through the numbers, as 1.2.3... 1233 HANG! You know he has problem with address 1233.

    2, export the address book from Outlook to Excel, then to identify contact contact 1233 (be careful on what address line starts on Excel - on mine it starts on line 2), then 1233-> row 1234.

    3, delete the contact.  go back to step 1;

    I had to remove 5 on about 2000 to make it work.  I can't say why these 5 did not work - I just like many other contacts with Chinese characters. BB9700 suspect "sees" something we cannot see. But removal of sync works.

    What a pain!

  • Problem blackBerry Bold 9700 Smartphone WiFi grey

    I just had nine white bold 9700 yesterday Rogers Wireless and tried to configure the WiFi at home. I have BIS plan data and my laptop can use a wireless without any problem.

    The phone found my modem and I put the WEP password correctly but it shows white dash and wifi on screen displays gray icon.

    I spoke with Rogers support technique guys 3 times:

    First, they asked me to turn off the phone, out of battery and put it back, delete profile and reset, it does not

    second time: turn off my modem and it reboot, it didn't work nor

    third time: they asked me to download desktop manager and Pocket code file to reinstall the OS. But I found that the link they gave me is Manager Desktop 4.6 which is older than mine (the CD comes with the phone is 5.0.1). Office) I have my mobile Office Manager (Windows vista x 64) installed 5.0.1 via CD, and I've downloaded version 4.6 and installed on my desktop pc (windows XP). But I hesitated to connect my laptop to one of them to continue. I don't want to spoil my BONES cell. For me, it made sense for me to reinstall the OS and even down to the version 5.0 to 4.6.

    Right now I use my BIS data plan to do everything (check email, BBM so far). I searched other posts and tried other things like run diagnostics tests, turn mobile network off and turned off wifi, turn on again, remove the wifi profile, analyze again put it back, take out the battery. None of those who work. Wifi at the screen icon is still gray.

    Should I try to reinstall the operating system via the Desktop Manager? and what version should I try? Any other suggestions?

    Greatly appreciated any advice.

    Helen

    Finally, | got it worked!  Here's what I did:

    1 browser > options > browser configuration > browser - hotspot browser

    2 browser > options > General properties > default browser - hotspot browser

    3 manage connections > wifi options > highlight my network ssid, click menu > edit uncheck prompt before connecting

    4 manage connections > mobile network options > configure data services, FAST roaming

    5 with the power, take out battery and a few seconds, back, restart

    6 manage connections > turn off wifi, then put it again

    7 manage connections > wifi options > highlight my network ssid, click menu > tools wifi > wifi diagnostics > linking > png

    Then the brand corss changed to check the mark, everything is beautiful

    I don't know what steps to take it worked, and I'm newbie, don't know where is the gprs or GPRS. But I really appreciate people here who gives so much help, I just combine their advice and keep trying, got finally worked. I'm so happy, thank you again! Hope this will help others.

  • DeskJet 3050 has J611 printer, windows 7 64, sony vaio F series with router netgear seem incompatible

    I was able to connect successfully the printer to my computer sony vaio notebook, as much as I first disconnect internet router, after that the installation I can connect internet once again, then it works for a few hours. However, when I turn off and restart the computer, the computer does not find the printer. Meanwhile, the printer is connected and has the correct network and are accessible from my Ipad or eprint, but not of my sony vaio. I tried all the solutions proposed in the various forums without success. Can anyone help? I also checked that my computer is on the same network. The printer appears "shadow" under devices and printers. Thanks in advance.

    What router are you using?

    We will set an IP address of the printer:

    -Print a the front of the printer Network Setup Page. Note the IP address of the printer.
    -Enter the IP address in a browser to reveal the internal settings of the printer.
    -Choose the network tab, then wireless along the left side, then on the IPv4 tab.
    -On this screen, you want to set a manual IP address. You must assign an IP address outside the range that the router sets automatically (called the DHCP range). You can find the beach DHCP from the router using its internal settings page or in its manual. Use the CD that came with your router or type the IP address of the router (ends para.1) in a browser.
    -Apply the subnet 255.255.255.0 (unless you know it's different, if so, use it)
    -Enter the IP of your router (on the Page of the Network Config) for the gateway.

    -Enter for the first DNS 8.8.8.8 and 8.8.4.4 for the second.
    -Click 'apply '.

    Now, stop the router and printer, start the router, wait, and then start printing.

    After that, you will have to redo 'Add printer' using the new IP address.

  • BlackBerry Bold 9700 smartphones may not make or receive calls

    I have a blackberry bold 9700 with TMobile, who cannot make or receive calls since yesterday.  Texts and e-mail work fine and I have done a battery pull approximately five times.  When I try to make a call, it is this constant clicking, almost like a pulse of sound that comes through the phone.  I tried to call the phone my wife and her phone rings with my number, but no voice crosses.  Same problem when I receive a call, the pulse thing happens and it goes to voicemail... which of course, I can't verify.

    I had this phone during nearly two years and that has never happened before.  This just started yesterday past and no change to the phone (OS update, new application, etc.).  Someone has an idea what is the problem?

    • Perform a simple reboot on the BlackBerry this way: with smart BlackBerry poweredphone, remove the battery for a minute and then reinsert the battery to restart.
    • If it still does not work, remove and reinsert the SIM card.
    • And, if still not, go to the store of your mobile operator and get a free exchange of SIM card and check it while IN the store.
  • BlackBerry Smartphones Blackberry Bold 9700 headset button does not work

    I just bought a Blackberry Bold 9700 with bell, (OS v5.0.0.432), and I try to use the headphones provided with the blackberry.

    The problem I have is that when I press the button on the helmet, I expect to start the voice dialing application, but the button does nothing!

    I tried to look for an option in the settings but can't find anything.

    Can anyone help?

    Hello

    Please make sure that you hold the button down for a few seconds, until the voice dialing function starts.

    Thank you

  • Smartphone blackBerry Bold 9700, Opera Mini 5 Beta, Version of the OS 5

    Hello

    I have a BlackBerry Bold 9700 with OS 5.0.0.321 Version platform 5.1.0.90

    I want to install Opera Mini, Opera site there is no option for the Bold 9700 also no option for OS Version 5.0, this means that I could not install Opera Mini on my last BlackBerry product? (

    Best wishes

    Hossein

    Mini 5 betas work on the 9700 fine.

  • Record of the blackBerry bold 9700 Smartphone

    Hello

    I have recently received a blackberry bold 9700 with Virgin Media and have been informed by Virgin I need to save that they gave me the e-mail address of www.virginmedia.blackberry.com to which I tried, but it is unclear what I do?

    Why should I save it?

    I would be very grateful for any answer

    Danielle


  • BlackBerry Smartphones the Motorola HS820 earpiece/Headset Bluetooth Audio works with the Blackberry Bold 9700?

    The Motorola HS820 earpiece/Headset Bluetooth Audio works with the Blackberry Bold 9700?

    It's not clear to me, if only the bluetooth Blackberry devices work with the Bold 9700, or any bluetooth device.  With the Bold 9700 recognize to ask the code four numbers when first by aligning it with the HS820?

    I matched two Plantronics, a Motorola and an earpiece/headset Cardo bluetooth with the 9700 and they work very well for phone calls, but I can't get the audio from Media Player to play on one of them.

  • Unlocked blackBerry bold 9700 smartphones - problems with third party browser applications

    Hi people

    I recently unlocked Blackberry bold 9700 (At & T USA) in India and using it with vodafone.

    problem is after unlocking iam not able to see the browser. even if I try t (third party app) browser install opra mini is not installing. I want to loop through using a Wi - fi connection available in my place with recording for BIS or BES by vodafone. So please let me know if you guys have any info. also here is the list of questions:

    1. the non-visible browser / unable to install opera mini

    2 storage mode is locked and disabled.

    3. password is enabled and locked (not able to disable the password).

    Thank you

    Alwin

    [email protected]

    Use the following post to remove the policy.

    http://www.BlackBerryForums.com/rim-software/67224-remove-policy.html

    I don't know what they have done, instead, to block the pin code. However, to remove the policy most likely will give you your hotspot browser. The policy can also block the browser BIS so you will want to get rid of the policy.

    Also, make sure that you don't always have the policy.bin on your pc or it will be applied after the abduction in method 1.

  • Cannot connect two computers with Blackberry Bold 9700

    Hi, I use Windows Vista Business on my laptop and desktop. Recently, I tried to connect via bluetooth, but computers don't have a pair with my Blackberry Bold 9700. I was able to locate computers on Blackberry but unable to enter the PIN on computers when you are prompted. I noticed that the two computers do not have loacte the Blackberry for matching.

    Hello

    You can check the configuration of Bluetooth with BlackBerry connectivity.

    http://www.BlackBerry.com/BTSC/microsites/search.do?cmd=displayKC&docType=kc&externalId=KB04132&sliceId=1&docTypeID=DT_SUPPORTISSUE_1_1&dialogID=778835513&StateID=0%200%20778821766

    Also check the computer settings to add a Bluetooth device.

    Set up a Bluetooth compatible device

    http://Windows.Microsoft.com/en-us/Windows-Vista/set-up-a-Bluetooth-enabled-device

    Change settings for a Bluetooth compatible device

    http://Windows.Microsoft.com/en-us/Windows-Vista/change-settings-for-a-Bluetooth-enabled-device

    The problems with Bluetooth devices

    http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-Bluetooth-enabled-devices

    Hope this information is useful.

    Amrita M

    Microsoft Answers Support Engineer
    Visit our Microsoft answers feedback Forum and let us know what you think.

  • Connection blackBerry Bold 9700 Smartphone problems

    I have problems connecting my device with the USB cable.  I tried three cables, and while my PC see my Blackberry Bold 9700 and evenb acknowledges his PIN code, it does not synchronize.  I tried to uninstall and reinstall the software, but to no avail.

    Can anyone help?

    If you have the correct version installed for your operating system (for example. Windows 32/64, Mac, etc.) and you run the program with administrative privileges then the end of the computer should be g2g.

    On the top of my head, you want to make sure that the SD card is not write-protected, otherwise I would just do a backup then a reload of the sw of pocket.

  • BlackBerry Smartphones Blackberry Bold 9700 for ORANGE bought in the UK, but never used does not work with TELSU SIM in the Canada

    I had a Blackberry Bold 9700 as a gift.  I think it was made for the Orange network in the United Kingdom ('Orange' written at the bottom of the BlackBerry in the front).  I tried to use it with my TELUS account in Canada with TELUS SIM.  The Blackberry does not register any wireless network signal.  The meter of signal display "SOS" only and no TELUS network is avaiable.  My position is Mississauga (Ontario) and Telus wireless covers this area for sure.  I checked that the device is not locked by going to Options-Advanced-online SIM card and typing MEPD Options Online.  The options that appear to say 'off '.  The device seems to read the SIM card because the SIM card # appears.

    Y at - it someone who has the same problem and its resolution.  A large part in this regard, the obligation for any input.

    Hello

    I just discovered the reason for BB does not not with TELUS that I wanted to inquire about registration CDMA you mentioned...

    A smart guy, he asked me to check the frequency bands that supports my BB.  Its sub Options => on.  "3 G bands" that supports my BB are 1, 4, and 8.  These correspond to the IMT 2100 MHz, AWS 1700 MHz and GSM 900 MHz respectively.  The frequencies that TELUS uses in the Canada are groups 1, 2, 5 and 6.

    So, finally tech TELUS came with the answer that my BB is designed to work with some UK frequencies and not with TELUS frequencies in the Canada.

    I've misunderstood and used the term incorrectly HARD LOCK.  The BB I have shows all the options as "disabled" when I go into options in advance-online SIM card and press the MEPD.  Also if I press MEP2 unit not asks me to input MEP codes.  Nothing happens.  This led me to believe that this device is not locked to ORANGE network so the lack of a better term, I used little HARD LOCKED.

    Much obliged for your entry.  It has been enlightening.  Thank you very much.

  • BlackBerry Blackberry Bold 9700 Smartphones blocked (or stuck) with 99% of the loading bar HELP!

    Hello world!

    Well, everything is explained in the title, my blackberry bold 9700 is block 99% of the load bar when I reboot it.

    Yesterday I had like 3 or 4 updates to some app and then I reboot but now it's blocked... I try to remove the battery several times, did not work, I try to use alt + shift + del several times, did not work, I try to use BBSAK but the blackberry cannot recognize... I don't know what to do and the worst part is that I did not do backup everything (ok so I'm little kind of stupid, but...)

    In any case of me HELP

    Thank you!

    YES! I found a solution! Working on it since yesterday! It is an application that has been blocked my BB

    So for all of you who have had the same problem here's what I did: I use the AppLoader, you will find cor D, F no matter) / Program Files / Common Files / Research In Motion / AppLoader / loader

    Launch the loader and connect your blackberry to the PC by USB. BUT it must detect the blackberry before the loading bar reach 3/4. So when the blackberry is detected, quickly click Next, then you should have a list of all your applications. Now deselect the application causing problem (or if you don't know which deselect all to remove all) and then click Next. PLEASE KEEP IN MIND THAT THE LOADING BAR SHOULD NOT SPEND 3/4. After that it's going to be something and if you see that it blocks just to make a reset in now alt + shift + del 2 times, wait, she returned to the loading bar and try again to detect the phone in the AppLoader who does not close during this manipulation... After all, that things blackberry should restart and hope for you, came back to life. So, in my case, I lost all my photos (don't know why), but at least I'm keeping all my contacts and messages. In any case it's better like this than all lost...

    Sorry for my bad English, I think that everything is not really clear, but perhaps that might help someone...

Maybe you are looking for