t460p does not start after windows birthday 10 update of 1607

Similar Questions

• Pavilion dm4-1265dx does not start after Windows 7 logo

  My laptop does not start after the "Starting Windows" screen when I try to boot the operating system normally. When I try to run the repair mode from the start nothing happens... I get a blue background image and the pointer of the arrow, but no icons or windows appear.

  I tried the system diagnostic mode by pressing ESC when turning the laptop on and the hard drive test fails every time, showing the following results:

  Test Drive: 1
  INTELLIGENT control: passed
  DST short: failure

  Failure ID: 64RG79-5AP62V-XD6U2K-60RN03
  Product ID: XZ298UA #ABA

  Hard drive 1

  --------------------------------------------------------

  Test drive: FAILURE

  How should I proceed? The laptop is still under warranty, but it was purchased in the United States, and I now live in the Brazil.

  Hello

  You will need to replace the hard drive.

  HP should send you a new drive for free, but in your case is a little complicated as you mentioned it already. Please contact HP tell them about this situation. How to do?
  Click on the link below and choose your country:
  Contact HP worldwide

• HP elitebook 2540p does not start after the successful bios update

  Hello people,

  I need your help.

  my hp elitebook 2540p with 2.5 "hhd does not start after a successful bios f.03 to f.24 upgrade done through windows 7.

  When I turn it on the blue light of wifi and power is on but nothing happen.

  I tried to remove the chip from the bios, cmos, hdd, ram, wifi battery... all, but nothing doesn't happen.

  I also tried to start it with the victory + b procedure and win + procedure four arrows so without USB key the caps lock flashing indefinitely but nothing happens, only the fan works quickly with a blue light

  with the USB the system restarts itself every two seconds and I have to remove the USB key.

  I do not know how...

  Thanks for any help.

  Luigi

  all very well now. I used the f.20 rom based on the internet and everything works again.

• Windows does not start after Windows update.

  Original title: udate Windows vista problems

  I have dell dimension e520, Windows Vista home Basic, 32-bit SP 2, and in January, I upgraded RAM to 4 GB to 1 GB. McAfee security on the computer. The system worked until the last updated (March 2012).  The computer does not start correctly after March 2012 update and System Restore restores to February 21 implemented to date.  The computer will then automatically install the updates again and restart, after which the computer will not start up again (an annoying loop).  I also lose saved data after the system recovery sets return date.  I tried Microsoft Fixit, which did not help.  Thanks for your help. Hurry LOL available updates.

  PS computer says 'patch blocking windows to start.  Some updates successfully installed previously, but on the next time you download windows updates, that try to download updates and others have "failed."  Sorry for the confusion but I'm rushing and I try to include all the symptoms, I don't see dealing with the problem I have.

  I had to take it to get fixed, thanks to the effort.  The person fixing said he ran a few cleaning tools and which appeared to fix.

• Computer does not start after Windows update

  I built my computer in December last year, which makes it less than a year. It has worked fine until this last week when I decided to give a few necessary windows updates a lot. I decided to download and install all night, and now it does not start. I get nothing on the screen. I don't get the safe mode options. I didn't get last known good configuration options. I don't not even a splash screen. After a full minute, it turns off again, regardless of how many times I turn it back on. It happened for a few days. Are no external hard drives not connected; only an intern. The only devices I plugged are my keyboard and mouse. Can anyone offer a solution? Whatever happened to you?

  I am running Windows 7 Ultimate Edition.

  The first time I tried to start after downloading the updates, he went to the boot screen windows 7 usual, that clear blue that says it configures windows and not turn off the computer during the process. Before we were told: "Welcome to Windows," he said "Shutting Down", but not before the configuration of progress has reached 100%. At this time, everything seemed normal. After the computer turns.

  Hello

  To fix your problem, you can follow the steps on this link. You can perform troubleshooting listed on this site by clicking here. The listed on these links troubleshooting steps are applicable to Windows 7 and more.

  Let us know how it goes.

  Best regards

• After the deployment of a Windows 7 image, pc does not start after Windows logo

  Hello

  I tried to install a laptop via a Windows Image. After that I deployed the image, the laptop does not start past the Windows logo. Normally I had to change the SATA AHCI setting to solve this problem, but he was already on AHCI.

  I tried to install it via a Windows 7 installation CD and it works, but I want to fix the laptop / image to work on this laptop.

  The logo of Windows get stuck, then I get a blue screen very quickly and it restarts. Also when I try to start in safe mode, it's the same thing. loading everything, then it gets stuck and also a really fast blue screen and reboot.

  Someone at - it an idea may be what the problem?

  BR,

  Jim

  I did restore by image much, many times without ever a problem.

  • I only use the integrated Windows 7 image creating installation
  • I only use a DVD + R White, never-r
  • I create the image ONLY on install brand new to be absolutely certain, there is no corruption

  I've heard of this kind of problem does not happen when the image was made from a damaged disc.  Which simply transfers the corruption.

• VMWare Virtual Center Server does not start after Windows Update

  Help!  I'm under vCenter 5.1 on Windows 2008 R2 with SQL Server 2008 R2 Standard.  I have applied the latest updates for Windows (critical only) as it applied Service Pack 3 to SQL 2008 R2.

  Now the vCenter Service does not start.  It generates error 7024 in the Windows system log:

  The VMware VirtualCenter Server service stopped with the error special service that the system cannot find the specified file...

  and error 1000 in the Windows application log:

  Could not initialize the VMware VirtualCenter. Closing...

  PS - I confirmed that the SQL instance is running.

  Absolutely nothing has been done except the Windows and SQL updates.  Everything worked fine until this point.  Ko an article deals with a "space" condition, but there are a lot of available space.

  I have attached the file vpxd.log, he created.

  Clues?

  Thank you.

  OK it turns out that the WWW service is interfering with vCenter Service on Port 80.  The thing is that the WWW service has been set to manual start.  Somehow during the upgrade Windows or SQL, one of them decided to turn auto-start. After the reboot, the conflict occurred.  Once I put the WWW back service to manual start the vCenter service started OK.

• Windows 7 does not start after the installation of updates - sounds familiar!

  Apparently, I have another system that no longer starts after you install an update to Windows 7. New kick computer _ I have to disable the automatic update of windows. Twice I had to restore the system in the first week because he hung up after the installation of updates for windows 7. I have no idea what update is the cause of the problem.

  Essentially, start the screen goes black with the cursor blinking in the upper left corner of the screen. The only way out is to restore the system.

  Does anyone know what update is the culpret? HP support has no idea. Their only solution was to update windows 7 to 'never download an update from windows '. It is a terrible thing to be underestimated solution.

  Here's the resolution...

  I installed all the updates except KB2284742 954430, 973688 and 971033. So I decided to install these 1 4 at a time in the order shown. I installed successfully 228472 and 954430 and 973688 disappeared from the list of available updates. So I installed 971033 and it installed successfully and I was still able to restart.

  My conclusion is that there is a conflict between the first 3 updates when they are installed at the same time.

  Now my system is up to date with all windows updates and I'm able to restart without any problems!

  Close this message.

• Windows 8 Pro does not start after windows update updates for April

  Hello

  Pulled up to my PC this morning and was asked to install updates from windows update. Check the list, there are 11 important available updates. I have unchecked and hiding implementing Nvidia updated as I want to do the updates of my GPU myself. Installed the remaining 10, completed and has been asked to restart my PC.

  The problems starts here; I am more able to start windows.

  It is past the bios screen, shows the blue flag with a circle of rotation below and then... nothing more than a black screen and my screen goes to mode 'sleep'.

  I tried to start in safe mode minimum clean using a prompt (bcdedit/set {default} safeboot) repair my installation disk option, but it does not start even in safe mode.

  I run system restore turned on so that the option is not valid for me.

  The system is now check the disk for errors, but it seems to hang there as well as happens for more than 2 hours now...

  Any way that I can return the updates of windows on the outside? Any other suggestions than the reset of the installation disc?

  Spec: Evga x 58 classified 3, Intel Core i7 950, 2 x Geforce GTX 580 in SLI, 12 GB Corsair Dominator GT DDR3, Corsair Force 3 SSD 128 gb, Dell u2711 2560 x 1440. Win Pro 8 x 64, completely up to date with the latest drivers. PC worked perfectly up to this Point.

  Disappointed that the "major updates" Microsoft kills my work machine.

  Problem solved now and it was the update of KB2808735 who was / is the origin of the problem.

  I placed my SSD into another computer and was able to pull up in SafeMode off and remove the updates.

  Installed all the updates one by one until it chrashed again installing the update mentioned above.

• iMac does not start after the last security update

  Hello

  After the last update my iMac (late 2009, El Capitan) does not start.

  The iMac starts he accepts my user and password entry, the loading bar stops at 80% and then nothing happens... after I turn off the iMac. Repeating this procedure change nothing.

  Does anyone have any advice for me?

  THX

  INTELLECTUAL PROPERTY

  a solution that helped me:

  Re: security update causes damaged Apps

• Problem with the HP Media Center M7670. UK - a - does not start after you install an update to Apple Quicktime

  I just installed the latest update to Apple Quicktime (once an update message appears on the screen). When asked if I wanted to re - start the PC now, I clicked on Yes.

  Now the computer does not start. The power led lights up, then the hard drive light blinks for a while, then nothing happens and the PC begins to beep. The beeps are repeated, with 2 short beeps and one long beep. What do the beeps mean?

  Then a CMOS clear would be the next logical step in troubleshooting.

  Here is a link to your motherboard page.

  Clearing CMOS information at the bottom of the document.

  It is usually the last step before giving up on a motherboard.

  The problem you are experiencing is hardware motherboard related firmware.

• Computer does not start after Windows 7 updates

  After the updates this week, Outlook crashed during an attempt to open the html emails.  I noticed that the Start button says to restart to be able to install the updates. Instead of restart, the screen went black.  I turned off and tried to turn on the computer.  Normally clicked and then dormant material.  Never on screen and remains black.  Have tried several times to disconnect all the equipment and power nothing doesn't.

  I have backups on an external hard drive but no ERD for Windows 7.  Read suggestions for open mode without failure etc. but if the SCREEN IS BLACK AND the COMPUTER don't YOU CAN t CHANGE THE PARAMETERS of START!

  Any ideas?

  Hi Joel,

  Thanks for posting your query in Microsoft Community.

  I suggest that you want to run auto repair with installation media and see if it helps you repair system files or not. For the execution of the task, I suggest you to try the steps below and see if it helps.

  Method 1: When you use the recovery environment (Windows RE) to troubleshoot startup issues, first try the Startup Repair option in the System Recovery Options dialog box. If this does not resolve the problem, or if you have additional problems manually, use the Bootrec.exe tool.

  Because you cannot start the computer, you may need to create a bootable Windows installation media, and then do an auto repair, and if this does not help then you try to restore your computer to the previous date.

  Note: When you use system restore to restore the computer to a previous state, the programs and updates that you have installed are removed.

  If you are using Windows 7 then the link provided below might help you to download and create installation media.

  Download Windows 7 Disk Images (ISO files)

  Method 2: If the problem persists, try to rebuild the BCD by using the Bootrec.exe tool. To run the Bootrec.exe tool, you must start Windows recovery environment (Windows RE) . To do this, follow these steps:

  1. Place the Windows 7 installation disc in the disc drive, and then start the computer.
  2. Press a key when you are prompted. Select a language, a time, a currency, a keyboard or an input method, and then click Next.
  3. Click repair your computer.
  4. Click the operating system you want to repair, and then click Next.
  5. In the System Recovery Options dialog box, click command prompt.
  6. Type Bootrec.exe, and then press ENTER.

  See the following link for more information:

  How to use the Bootrec.exe tool in the Windows recovery environment to troubleshoot and repair startup issues in Windows

  http://support.Microsoft.com/kb/927392

  Method 3: If after performing the above steps, you are able to start the computer and access the desktop then try to Uninstall KB3097877 update if it is installed, and then reinstall it.

  Hope it would help. If problem persists always post back with the current state of your computer and the result of the proposed suggestion, we will be happy to help you.

• Z50-70: does not start after Windows Update

  Hello everyone, I recently bought a Lenovo Z50-70. Today, after a Windows Update, I restarted the laptop and now the led, but nothing happens. What could have happened?
  Thanks for any advice.
  Stefano

  stefanocsl wrote:

  I can't enter the BIOS because when I turn it on, I can't do anything. Also does not show the word "LENOVO" to boot, I see the light, I'm not the fan noise or HD by pressing the power button does not turn off, so it is as if she is still locked, turn off I have to hold more than 5 seconds

  Rather than go deep with solve the problem, it's better that you call support for repair or replacement (better) because you just buy the device recently.

• X 1 carbon does not start after Windows Update.

  Hello

  It was a yes I work on this X 1 computer laptop carbon and no default value.

  I had a windows update yesterday, I did it and my computer turns off naturally.

  This morning, I can not start it, it starts up fine, Lenovo sign appear but nothing after. only a black screen with blinking underscore.

  Any ideas?

  Thanks for your help.

  Hello

  Thanks for your help, but I already did that and no results. I call the warnaty Center and they change the card mother and ssd. so I lost all my files... they told me that they can save them...

  Now, I received a laptop cool but cannot be used because the SSD is not empty, no part of recovery and they gave me a cd of installation still... 2 weeks without a computer for my CEO with all files down... really painful.

  I close the topic, thanks for your help tho.

  Kind regards.

• My phone is lock and does not start after you install an update to Windows.

  After you have installed the Windows Vista Home Premium on my laptop, I am unable to start my laptop properly.

  Boots systems and load normally until the display of connection where instead of the login screen, I show the screen updated frozen on "Installing part 3/3 (0%) update." The laptop stays on this screen, with the cursor froze with a loading icon, for about half a minute until the screen shuts off and reboots the system, put the system in a loop, I can't on.

  I tried: turning off on and powered. using advanced boot options to open the system to all types of 'Safe Mode' and leaving the laptop for some time before trying to turn on the system again. All these things have not worked and the system remains in the lock down.

  I wonder if it is a common problem after the latest Vista updates or if it is more specific to my laptop. Whatever it is, any kind of feedback and advice would be most appreciated.

  Thank you.

  After you have installed the Windows Vista Home Premium on my laptop, I am unable to start my laptop properly.

  "part 3/3 (0%) update installation." ... and restart the system.

  See if this sugesstion can help you:- http://support.Microsoft.com/kb/949358 >