T540p mouse Offset

Similar Questions

• iTunes 12.5.1.21: mouse offset

  I installed 12.5.1.21 on Windows 7 Enterprise 64-bit SP1 and now my mouse clicks are disabled by like a couple of centimeters.

  By off I say that when I place my mouse cursor on a title of the song is the song below, or two song belong who gets highlighted. So in order to select the song that I want I have to position the cursor of the mouse as 4 cm to the top and 4 cm to the left before clicking.

  I use a multiple monitor with NVIDIA Quadro K1000M (Driver version 368.39) configuration.

  Something has changed in the way handles 12.5.1 the mouse input (since 12.4.2 do not have this problem). Does anyone know a fix for this?

  This is caused by the IPR police scaling in Windows 7.

  In Control Panel > appearance and personalization > display > small 100% (instead of the middle of 125% or 150%).

  In my case, 125% is the default and that causes iTunes to misplace the cursor.

  After having changed the font scaling to 100%, you will have to disconnect and reconnect to see the effect.

  Fonts in iTunes are more blurred, and the location of the mouse is followed properly within iTunes.

• Offset of DirectX 10 problem mouse

  Hi, I am running Windows 7 Home Premium 64-bit edition. I have an Intel i7 940, 12 GB of ram and a 250 of nvdidia graphics card. My problem with DirectX 10 games running. When I run a game like Crysis for example. my mouse is actually down and to the right of the where the cursor indicates that it is. Thus, for example, if I want to select the first item in a menu, I need to get my mouse down about an inch and a half inch to the right of the menu button. If I play in mode resolution 800 x 600, then my cursor and the actual location of my mouse are synchronized. If I play at a higher resolution then the lag gradually gets worse until I can choose is more options on the screen. If I start the game in DirectX 9, the problem of the mouse will not occur. If I tell windows to set my Visual settings to "best performance" then everything works normally even in DirectX 10. I understand that aero or transparency is what is confusing things, but is there an any fix for this? I'd really rather not change my windows settings each time I want to play a DX10 game.

  Hello
   
   
  Perform the two methods listed below and check if that helps get the pointer of the mouse in sync.
   
  Method 1.
  Try to synchronize the computer with the resolutionof the game resolution. It should solve the problem. For example, if you are gambling 1078 * 768 change the resolution of the computer to the same and check.
  
  Change your screen resolution
  http://Windows.Microsoft.com/en-us/Windows7/change-your-screen-resolution
  Method 2.
  Change hardware acceleration
  You can also try to change the acceperation of material in the middle and check (you can try different)
  1. right click on an empty space on the desktop.
  2. go in the resolution of the screen.
  3. click on advanced settings, then click on the tab "troubleshooting."
  4. set the hardware acceleration in the middle. (here you will get the option only if your video card supports).
   
   
  I hope this helps.

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• OFFSET of mouse as _ any when the computer is something in the background. User/Windows interface, all, staggered as I use windows 3.1.

  Hello

  I'm really bothered by the fact that my trolling as _ mouse in Windows 7 any time of installation is done in the background, is opening a program or anything like that.  It seems to me as being the fact that we are not in 1995 over this issue should not occur.  How the _ did I have 8 GB of ram and a quad core i5-750 processor and my machine mouse is trolling as _ in these situations?

  I use a logitech optical mouse wireless.  I reinstalled the drivers and software for this 3 times.  Also, I moved the USB connector on the front of my Dell machine.  Still no difference.  Help, please!  I love Windows 7 so far, but the functionality of a mouse I do experience is unacceptable!

  Justin Hansen-

  Software engineer

  You might consider replacing the battery in the mouse?  Or, try not to use any driver module and the software - just plug it in and use it.  It work?

  What if you start in safe mode, or with a boot or a boot device - have you noticed the behavior then?

• I have a problem with the offset of mouse in Windows 8.

  Original title: Windows 8 mouse lag - it kills me...

  I installed Windows 8 pro on my pc vista (32 bit).  I used Microsoft's tool to evaluate my PC for Windows 8, and he says it's good to go.  All was well with the mouse in Vista.  Windows 8, there are a ton of delay mouse, making the computer almost useless.

  I'll assume that you are using an Intel HD4000/2500 GPU. This something I have lived on many facilities between multiple computers. The only way I was able to solve it is to return to the WDDM driver 1.2 Intel from Microsoft instead of the ones directly from Intel. Unfortunate side affect is that OpenGL does not work with Microsoft drivers, so some games will give you an error.

  To do this:

  Win + R

  devmgmt.msc

  Expand graphics cards

  Right-click on the Intel list, and then click Update drivers

  Click Browse my computer

  Click on let me choose

  Look for Intel Microsoft Corporation WDDM 1.2 (not exact text)

  Click next

• The mouse cursor offset w Redline cursor in a model.

  My mouse and my redline cursor (in the model) are staggered from each other and it is only in AE, no other software. No idea why?

  Watch this video...

  My OS is: 10.11.1 (B 15, 42) (El Capitan) and my AE is CS6.

  I got it! It was a thing of resolution. I switch monitors and switch back. See you soon

• Problems of mouse with display port 1.2 in MST (display 4K)

  With macOS Sierra, there is a strange thing with 4K display connected via DisplayPort DP 1.2 STD mode (required for the 60 Hz refresh rate).

  As the screen is divided into two screens sub in this mode - mouse behaved differently on each half of the screen. It seems that the right side of the screen has offset of mouse close to 50 pixels.

  With mode DP 1.1 standard there not such a phenomenon.

  My hardware is: MacBook Pro 15 "end 2013, display: DELL UP2414Q

  BR,

  Pawel.

  Hi Emmanuelle RLAP Guraj,

  I understand that your mouse works differently when you use it on the right side of your external display Dell. You can try to adjust the display settings of your system preferences and also check your display Accessibility settings.

  macOS Sierra: show the pane of the system preferences of monitors

  macOS Sierra: show the pane of system accessibility preferences

  I also reset the NVRAM.  How to reset the NVRAM on your Mac.
  
  

  What is NVRAM?

  A small amount of memory on your computer called "non-volatile random - access memory" or NVRAM, stores certain settings in a location that OS X can access quickly. Settings that are stored in NVRAM are dependent on the type of Mac you use and the types of devices on it.

  If none of the above resolves the problem, try to start the Mac upward in Mode safe mode to see if the problem exists. Try safe mode if your Mac does not start-up
  
  

  What is safe mode?

  Safe mode (sometimes called secure boot) is a way to start up your Mac so that it performs certain checks and prevents certain software from loading automatically or opening. From your Mac in safe mode does the following:
  Check your startup disk and attempts to fix problems if necessary directory
  Loads needed kernel extensions only
  Prevents elements start and the login items open automatically
  Disables the user installed fonts
  Delete font caches, hiding the kernel and other files of the system cache
  Together, these changes can help resolve or isolate issues related to your startup disk.

  These measures should have your mouse works as it should show everything using your external Mac OS Sierra. Please use the Apple Support communities to post your question.

  Good day.

• Magic Mouse Lag and disconnection

  10.11.5 MacPro 5.1 mid-2010

  The offset of the mouse and the disconnection is so bad that I had to go back to a mouse that is causing a problem in my production. I'm a graphic designer and the need that the mouse. I tried all of the solutions I've read here and on the web without success. I'm going to buy a bluetooth adapter to see if that helps at all. Any suggestions on this dongle/adapter or if someone found a solution to this problem of bluetooth. I have new usb 3.0 devices and cables to come this week and as I read disconnection worsens with usb 3.0.

  Anyone, please help before I have no hair left!

  If your using a first generation Magic Mouse, the disconnection problem is sometimes caused by faulty battery contacts. Here's a solution:

  How to fix the magic mouse disconnect problems

  Tracking errors can be fixed by simply cleaning the lens: Year Easy Fix for a Magic Mouse Tracking problem

  And some bluetooth connection problems are caused by a corrupted preferences file: How to fix the OS X Bluetooth Wireless problems

  Tom

• Position of the mouse in a chain of control/indicator

  Hi all

  By using LabVIEW 2015 and would like to know if it is possible to do the following...

  I have a string with a paragraph or two of text.  In this text, certain words and phrases are highlighted (by different font color).

  I would sense when the mouse is positioned on one of these and change the type of cursor when it is over them.

  .. think of hyperlinks in a browser.

  I feel when I'm on the control of the chain itself, but not for specific text.

  Any ideas?

  Thank you!

  Charlie

  The string should contain a method that takes the coordinates (which you can get from a mouse event down or move the mouse) and tells you where it is in the string. Create a node to invoke for the string, and then select the method used (I think he called Point byte Offset). I don't have any experience with it, but I guess it compensates for things as sizes of scrolling and the police.

• Hovering over the triggers Drop Down Menu event "mouse Leave"

  Hi, if anyone can help with this problem, I would be very grateful.

  I have a tab control changing to another page when the user enters or mouse leaves the tab control. The purpose of this is so that the tab control becomes invisible when colored 'transparent', according to the movement of the user's mouse. This allows the full screen to use to display the video when the menus are not necessary, and menus can be displayed when the user enters into the surface of the tab. There is also a button to lock the menu in place.

  It worked fine until I added a few rings of text to a menu tab. When the user clicks on the drop-down arrow and hovers over the elements, the case of the event as if the mouse has left the tab control, tab resets back to page 1 (white page). I don't want to do it, but I still want to use the drop down menus because they are more concise and more convenient than the alternatives (listboxes, etc.). This does not happen with the buttons and other controls, only with the drop-down menus, AFAIK.

  Can anyone suggest a work around? I chose this method of relaxation because it is less demanding in processor using the mouse move event coordinates to trigger the tabs appear. I need to save so much time processor for video capture possible. I enclose my vi (Labview 2010 32-bit) with the gray tabs so you can see and test the value for yourself.

  I would add one for the event to "Operate the Menu Activation" for the controls of the ring.  This simply fuels a real constant in a shift register in time loop.  In the mouse enter and leave events add a case structure and change the pages only when the value Boolean false.  Ensure that supply the true value in the registry to offset in the mouse leave case also (other cases may use the Default of False if you don't have to string wires in all cases).

  Quick MOD after extraction of the stuff IMAQ, remove also the delay in case of loop Structure, provides it ARE necessary delays.

• greatness of calibrated 2 2 mouse moving measure determine the axis of rotation

  Hi all

  like other posters, I am very new to LabView, so if it is a very simple problem, please have discretion and still try and point me in the right direction - thanks!

  I'm trying to measure the extent of the optical mouse movement by calibrating to another.

  I have attached the VI below - the original VI was a VI of detection of position that was available on the forums.

  Basically, the problem I have right now is that I need only the first value that goes into the registry change however it constantly displays the values when the Enter key is not pressed.

  Finally, I want to measure the 2 mouse movement at the same time to determine an axis of rotation and angular displacement, but I don't know how to acquire the position of the two mice, so if you have any suggestions for this problem I would appreciate it really only also.

  Thank you!

  Brad,

  Please specify your logic.  I modified your program to demonstrate a way to do this.  I replaced the subVIs with two controls: a back button and a slide called mouse switch. I added a registry to offset to keep track of the previous position of the back and simple logic to detect only the transitions of T F and F and T.  Then he used two structures case to place the appropriate value for the mouse in the registry to offset and to do the calculations and refresh the display.  The structure case T F could be replaced by a Select node in the palette of comparisons.

  I also increased the waiting time so that you can see the LEDs transitions.

  Lynn

• Microsoft Bluetooth Wireless Laser Mouse works, extremely, annoyingly slow after change of motherboard out sometimes.

  I have problems with my motherboards.  I installed originally a jury of six core AMD Asus but discovered that the sound circuit on the Board picked up the RF of six hearts.  So I changed it to a Biostar TA890FXE an AM3 Board with 4 PCIE slots.

  This map may contain 4 Pcie, but has only 2 16 x slots that are white in color for Crossfire.  The other 2 Pcie are for the slower cards.  I have my card installed in slot 1 PCIe 16 x

  Since I was a boxed version of Vista Ultimate 64 bit the replacement of the Board of Directors has gone well with without a hitch, except for this problem.  The darn wireless mouse keeps presenting a significant delay from time to time.

  I upgraded to the latest BIOS and also found that a USB Joystick was also causing problems until I uninstalled the ATI Radeon drivers several times.  I have uninstalled/reinstalled all drivers USB again and again.   I even upgraded from 8 GB to 16 GB of ram Corsair and the thing does not run any faster (except for loading video in an editor) than my Asus M4785M with 4 GB ram.

  At first, I figured the card Radeon 4650 diamond with 1 GB of ram, when I ran FSX I got frequent black screens between refreshes.   When the aircraft was in its window the mouse lag so I moved it into the box with the graphics.  I could move it very quickly from time to time but not always.  As soon as the mouse has crossed the border of the FSX menu in the aircraft selection menu, the LAG would begin.

  Strange however, I also have the Microsoft Bluetooth Entertainment 7000 keyboard and it has a built-in mouse pad.  So when I got the offset of the wireless mouse I found that the mouse pad, keyboard do not show it.  Of course, a lot of batteries have been tried.  I have also a key 3G modem and the thought that maybe the RF frequencies could interfere with the bluetooth transmitter, and yet the mouse KEYBOARD pad worked fine all the time!

  At a point of the USB ports on the front of my PC failed suddenly and I used the port in the back instead, as the 3 g modem suddenly was cut.  He started upward once again connected to the rear port, but he chose all of a sudden another 3G network, spend roaming, something that isn't supposed to

  occur.

  So it seems to be a USB problem.  I double checked the connectors on the front panel plugged into the motherboard header, but it was close.  I removed it and he exchanged with a rear slot spare USB cable I have no problems. I even swapped the transmitter Bluetooth of the rear USB ports in the front and vice versa, and these problems went away.

  Yet from time to time, there will be a sound of loading the disk heads and there will be a lag on the mouse and it flit on the screen itself.  I removed all the USB drivers and mouse drivers and drivers of keyboard without result, I then plugged a wired keyboard and mouse while the USB was plugged in and waited.  The wired keyboard had built in the trackball, so I couldn't move around as fast as Bluetooth, one mouse cursor and again, I got the mouse slows down from time to time.   Most of the time is when a noise was heard from the hard drive.   I turned off Superfetch to listen to the record and it made no difference.

  I left the PC running on its own after turning off any energy saving features and when I came back to it, I finally found that the keyboard was a lag now, too, I had to wait about 30 seconds for something to wake up until the keyboard is recognized.   It seems that it is the same problem that mouse, but at a later date.  I then re active features and screen saver and keyboard lag reduced significantly saving energy.

  Then, once, I got a huge amount of lag when Google open white paper screen, the mouse cursor wouldn't move at all for a long time or erratically.   In this case, I thought to 'pull' the wired keyboard and the trackball at the back of the card, and the problem immediately disappeared as if there were conflicts.

  However, this did not last long, and about an hour later, the mouse pointer lag appeared.  Don't forget this mouse worked fine for a year on an Asus card and withdraw it very well.

  My next attempt with the Bios, and it happened unexpectedly.  This motherboard has a utility to start Bios screen where I can put my own splash screen and no the Biostar on a difficult start.  So I did and all of a sudden all the problems cleared up!    It was as if something in the Bios was hung in, and then there is this whim of hard drive noise and once again, lag lag lag on my mouse.   With 16 GB of ram and 1 GB of video ram?  Just to not use the Aero's office, no sense at all to me.

  Tried to contact Biostar for 12 days now, no response.  Have the latest drivers for vista from windows for the keyboard of entertainment and mouse, service pack 2 for Vista and a 1 TB hard drive, 500 watt antec PSU, problem occurs with or without overclocking.

  Anyone?  Anyone?

  AMD Phenom 2 1090 t black edition 3.2Ghz

  HD4650 diamond! GB

  Corsair XMS3 DD3 x 4 1066 4 GB

  1 TB of Seagate SATA

  Antec 500W PSU Green

  Note: This map has a header of a CD rom, but also the DVD Sata PATA

  Latest

  I could no longer the transceiver Bluetooth 2.0 with the mouse and keyboard.  I went to a keyboard and a wired mouse again.   Then a few days later I decided that I would plug the transceiver Bluetooth 3.0.  This time it installed fine even if I had uninstalled the Intellipoint software.   I went then to the receiver Bluetooth 2.0 and it didn't work anymore.  I did a reboot between the two, and suddenly I saw a Microsoft update will appear at the bottom right of my screen.  I left it to update, and then he said that I could connect other bluetooth devices other than my keyboard of entertainment game.

  Well, this is not true at all, for the entertainment keyboard transceiver pairs automatically.    Yet, this message appeared.  When I went into the control panel to verify the situation once again, I found that there is no Bluetooth icon.   From what I've read on other Vista users using a transmitter of 3rd Bluetooth part, it seems that the Bluetooth stack has disappeared because I mixed the two Microsoft Bluetooth transceivers.    Something else occurred as well, it reminded me of moments where I would install a new installation of Win98 and some drivers as the main card drivers were not yet installed.  He will have to restart the system and over and over again for each driver be seen, and if we were out of sequence, should be made to remove and start over again until all have been installed.  In this case, it seems to be the same kind of priority when it comes to the way in which the Bluetooth drivers are installed.  When I removed the Bluetooth 2.0 transmitter/receiver and replaced by unity Bluetooth 3.0, I seem to have rid one of these priorities, let the program update that must have been stuck in the pile of pilots, how the keyboard and the mouse works perfectly now.

  With 3 wireless transmitter that is I can no longer use the Bluetooth 2.0, one all the more, I plugged it in different USB ports and we saw him, but it was not enough to cause any installer to appear.   It's as if they are reticulate together now, and I can no longer use the add a device feature.   Even if I add the second transmitter/receiver, it is simply ignored.

  Since then, right now I have no need of an additional feature and the keyboard works very well, I'll keep this configuration until I have to reinstall the motherboard still when I start then a clean Vista install.  Unfortunately the new motherboard that I received does not work as I had hoped it would be, not that it would affect the situation above, that's simply not what I was told it was, and I plan to return it the manufacturer once more.

• Dell p2815q monitor lag mouse?

  I noticed that on 4 k 3840 x 2160 at 30 Hz, I grabbed it trolling. the mouse is a bit slow, even if I turn my dpi and acceleration for the climax. 3600 dpi and even 10 acceleration (itested each ppp parameters are always behind.

  I also tried all THE usb ports on the monitor and my laptop

  However, when I'm on 1920 x 1080 at 60 Hz, I'm completely fine, no problem of lag at all here.

  My specs: 8 GB of ram, nvidia gtx 765 m, intel corei7-4702HQ CPU @ 2.20 ghz ghz 2.29

  Did someone else gets the same question?

  Because of the hardware architecture, the offset of the mouse is the result of the P2815Q requiring 100 ms to process video data. This can be changed with an update of the firmware. It should be that the new architecture from the ground up, which we will not be made. If you have this problem, and he can't work around, your only recourse is to return the monitor to return. Outside the first 30 days from the date of invoice, it will take the Manager's approval to get a refund. Using the P2815Q Dell service tag number, contact Support Technology Guide for your region. Explain that we do not have a fix for this problem. The technician must degenerate to their Manager.

• ARC mouse jumps, jumps and lags on the screen.

  Original title: Arc touch mouse problem

  Installation: Win7 32-bit
  Mouse: Intellipoint 8.20.486.0

  I used my new mouse wireless Arc Touch for a few months, and I noticed a problem that gets worse gradually. It's now to the point of complete gene.

  The issue: the mouse pointer jumps and skips or lags on the screen. She always does with usage, but real offset a leap occurs intermittently (in other words, the mouse can sometimes work correctly, but guaranteed it is de-energized several times during navigation, session, etc.).

  Browsing the forums I noticed of course questions of others, but none are quite the same thing or maybe just broke the extent wherever I did the behavior of the mouse.

  My first thought was: computer settings. I checked the drivers (with 8.20.486.0 at display time) which were already very good. I re-downloaded and installed in the case of corruption.

  I checked another mouse Wireless: works perfectly without offspring (also a microsoft bluetrack) which works perfectly.

  Then, I changed the batteries in the Arc Touch. A still jump/gal.

  Finally, I noticed that the blue light seems to waver. When the mouse is stationary, it is bright and intense. When movement starts to happen, it fade dramatically and start blinking or completely off for a fraction of a second. I think the material is defective, but is not complete of course.

  Any other person with mouse problems seen elsewhere? My other mouse bluetrack does not have this flicker.

  Try to put your receiver in mouse as close to mouse that you can without having a gene and see if that has any effect.

  Ensure that all that allows to send a signal wireless iphones, tablets ect are slightly away from your mouse, she could be reached.

• No arranca windows 8, solo pantalla in blanco's observed is el mouse

  laptop (hp pavilion g6-1d60us con upgrade Windows 8 pro, trabajo good desde activacion hasta ahora), al encender is is loading windows por horas y the return there encender presenta pantalla e logo indica reparando sistema, luego appears pantalla in blanco is observed to solo el is observed to el offset than hago en el mouse pads, no windows of arrancar of finished.

  thank su Atención.

  Please select your language in the drop-down list at the bottom of the page to post your question in the language of your choice. The forum in which you've posted is for English only. If you can't find the desired language, support for additional international sites options are by following the link below: 

  Please, select su idioma in her lista desplegable anterior to send you in el idioma of choice su pregunta. El foro Québec ha published're para frances only. If usted no encuentra el idioma no desee por encima of las options para support otros destinos international themselves can find following el siguiente enlace:
  

  http://support.Microsoft.com/common/international.aspx