TANDBERG Edge 95 MXP component

Similar Questions

• Tandberg Edge 95 MXP Password reset via the remote control

  Hello

  I try to reset the IP password via the remote control and still get the complaint that the password must be at least 8 characters and the number. I tried all combinaiton of 8 characters and 1 number, 8 characters and 2 numbers, 6 tanks and 2 numbers, 4 characters and 4 numbers, number 8 characters and 1 number 1 and so on. Is there something special about looking for the system?

  Thanks for the support!

  PS. When I telnet into the system, it shows TANDBERG Codec Release F7.2 PAL / SW Release Date: 2008-10-31, so I guess it is 7.2.

  Do you know if strict password is enabled or not?

  By default, that is, unless you have turned it off at some point, which will ask for a password at least 15 characters that contains 2 lowercase letters, 2 caps, 2 numbers and 2 special characters.  You can check by connecting to the endpoint using SSH or Telnet and runs the API command below:

  xConfiguration StrictPassword

  Here are the steps to reset the password to access IP on a TANDBERG MXP endpoint, I suggest that you try to use the API to change the password by logging on to the endpoint by Telnet or SSH instead of the remote control. The most recent software MXP is F9.3.4, suggest you also improve your point of termination to the latest version to mitigate the security issues with the older software. You can contact TAC and advisory security cisco-sa-20140605-openssl to get a key to unlock so you can upgrade your MXP to software F9 of reference, from there, you can upgrade to F9.3.4.

• Does anyone know why an edge 95 MXP will call himself?

  I have an Edge 95 MXP and call himself all the time... the call is a SIP call of [email protected] / * /a call of 64K and the IP address. I don't have the power off because it's in the ceiling.  The unit is also recorded as a 3rd party endpoint call Manager 10.5... The unit can make calls at our other fine video devices. I had to set the unit to auto-answer, so it does not sound at all times.

  Usually, it is because your getting analyzed by applications such as SIPVicous tent identify opportunities for exploitation of circuits on UDP SIP PSTN.

  In general, this risk is mitigated by closing the firewall ports for the endpoint or by making a few changes to its configuration.  On a codec of series C, EX, SX, MX running TC software that is easy, but I do not know the equivalent commands (if there is) for a codec MXP.  However, you should be able to block the scans that cause this by closing the port UDP 5060 if the codec is open on your firewall.  If she goes by a gatekeeper as a VCS server you could disable UDP, I do not know CUCM.

  This has been asked several times, do a search in the forums for "100 @" found the following results, although they all have to do with a series C or VCS codec, but it's all the same question.  The unit is publicly accessible via the internet, it's just a matter of closing or adjustment of the endpoint configuration or call control server.

  lot-Calls-Numbers-100-and-101-looks-Self-Calls

  strange-appeal-loop-c40

  Cisco-VCS-Alarm-Call-License-Limit-Reached

  C20-phantom-appellants

• Tandberg Edge 95

  Hi, can someone please help?  I have a Tandberg Edge 95 I have connected 2 monitors for... The primary monitor is connected to the DVi Out o th at the back of the unit.  The secondary monitor is connected to the Composite video output (1.Dual) to the device.  When I want to send (my PC) content at the end as a presentation, I can also see it on my main screen, but I want to see the camera from the other end on the secondary display. Currently, I can only see the PC or the local camera on the secondary display.  I tried a combination of parameters, but can not get the camera from the end to display on the secondary monitor while I have the content of the PC on the main screen.  I also tried the output S - VIDEO and Composite video output (2.Single) without success.  Can someone tell me please how to operate?

  We have a number of Edge95MXP using two screens and controlled - AMX works well.

  However, all the programming is done for us by people you really know their AMX programming and Cisco/TANDBERG products - that helps.

  Jens

• Phone type Edge 95 MXP found in CM8.6

  Hi all

  I try to add new phone device in the handler calls 8.6

  However, I can't find the type of phone Edge 95 MXP.

  I need to download any firmware, or choose another type of similar phone?

  Thank you

  Sam

  Hi Sam,

  Unfortunately MXP endpoints are still not supported for registering for the CUCM. Support is available for the series C and Ex-material of the series right now. You can see the release notes of the MXP software for updates in the future.

  Kind regards

  Saint André

• Tanderg edge 95 MXP I need something else?

  We have this device used to indicate the following legend "cannot receive or make calls. Network option is not installed. Loking bandwith installation option"for options, I found the next:

  Table 3. Order information

  Product name reference compliance model number

  Cisco TelePresence edge 95 MXP CTS-EDGE95-K9 TTC7-14

  Comes with: Edge MXP codec, bandwidth of the ISDN/2 Mbps IP 512 Kbps, natural presenter package, MultiSite, Cisco

  Telepresence PrecisionHDMC camera 720 p, 1 microphone, remote control

  The video Standard Options - choose a

  CTS-NTSC for Edge MXP CTS-NTSC

  For Edge MXP CTS-PAL PAL option

  First, this problem is related to the licences?... Can anyone guide to me to find out what this option (in the case that was the problem)?...

  Thank you very much

  Hi Ing,

  There seems to be some contractual problems, you need to prosecute TAC for the reason of the integrity and security of data.

  may be that it will be not supported by the current state however there are still have alternatives.

  I can give you an overview.

  This device is not showing any contract and could not find any customer order number, probably you can anticipate that you would have the documents of purchase for this device.

  You can join the account manager for your company that manages the update of contracts like this

  as the now he gets that one associate who is the product key and is installed to make edge 95

  no other option generated

  as I do not have the SO or PO number can not verify if there was another option purchased,

  You can reach the center of sales cisco for any purchase of additional keys, or your accounts team

  Thank you

  Ravi Kr.

• Question of presentation on EDGE 95 MXP

  I have a client who has an EDGE 95 MXP system and complains that he is to have a lot of problems with its laptops, make presentations of PC. Some of its laptops work well, others not. He reported the following portable computers as does NOT:

  HP 8740w

  HP 2560p

  HP 2550

  HP 8560p

  Dell Precision M6700

  HP 6730 b

  He had no problem with the following laptops:

  Dell Latitude E6530

  Dell Latitude D630

  What's weird, is that if he uses a 50 foot DVI to VGA cable for its computers laptop problem, it works! It does work with the original cable 15 feet. The cable has been replaced so we know this isn't a cable problem. The codec was also replaced at some point. 50 foot DVI to VGA cable was a Cisco came up with solution but the client indicates that it would be foolish...

  Anyone got any ideas how I could get this client on my back? I am sure that it is a setting of the laptop or the driver to the origin of the problem, but my client just it.

  Thanks for all your help :-)

  We have seen similar problems in the past with some portable computers when using DVI VGA, replaced cables cables with VGA to VGA cables and used a VGA to DVI adapter on the codec itself set. (We also forced 'VGA Out quality XGA')

  /Jens

  Please note the answers and score the questions as "answered" as appropriate.

• Strange behavior of edge 95 MXP endpoint

  Hi Experts,

  I have a Codec on the client side (Germany), it's an edge 95 MXP with software version F9.3.1 PAL. Every time when I call from my 150 MXP, video calling is disconnected by this Code after 58 seconds. When I make the call of this Codec to my 150 MXP, it's fine. Everyone knows that kind of situation before?

  Thank you

  Jerry

  The difference between incoming and outgoing is usually a firewall - a dynamic firewall will allow the movement of return for outbound connections, but an incoming connection will have specific rules created to allow traffic to the inside.

• Tandberg / Cisco 6000 MXP Riddle

  All righty then,.

  I get more and more these investigations the latter time.

  A customer has a 6000 MXP and they are curious about the features, options, and software updates. No I have not contacted partner Help Center and TAC asking a simple question. "Can you please tell me what options (multi-site, option high resolution, etc.) and the revision of the software the unit originally shipped with? Well, since the unit is no longer under warranty, or under contract, they cannot open a grace case a license to just me provide this basic information. NOTE that I can go connect to Polycom and pull up the full story of a product by serial number, even if it was sold in 2005 without hassle. Cisco take Note!

  In any case what I need to know, what unit, the latest revision of software can be upgraded. It's a

  TANDBERG CISCO TELEPRESENCE 6000MXP TTC6-08 REV2 CTS-INTP6000-K9 serial number 25 has 05184

  It would have been nice to know what are the options she was allowed with but hell I'll settle on the latest SW version that this thing can be supported. The thing is that if I remember well, that all depends on a license key. That means that I can not update the SW without providing a license key to activate it, Cisco cannot provide because they offer is no longer supported the product and without the license key I can't upgrade the software. Anyone have any ideas?

  To find out what features and license keys the MXP comes with, you can find the serial number of the codec using Cisco Licensing Portal > obtain other Licenses > license TelePresence to return.

  The latest version of the software is F9.3.3, if you are already running F9.x you can update without needing a release key, but if you do not have F8.x or below, will need you a key to unlock.

• CTS edge 95 MXP microphone option

  Hello

  I want to have an optional microphone to the edge of the 95 CENTS, but I couldn't find the PN the microphone on the technical details of the 95 edge. can someone help me with this.

  Thank you for your help.

  Kind regards

  Omar

  PID: CTS-MIC-OMNIDIR =

  He is Omni Microphone directional (AT841UG) includes cable 7.5 m

• The MXP 95 edge Firmware update

  Recently, I came in an operation using a Tandberg Edge 95 legacy. The firmware of the device, from what I can tell has never been updated. It is currently running F6.0. I downloaded the F9.0.2 package but I am not familiar with this procedure. Can someone help or direct me to a site of insturctional on the updating of this device?

  upgrade is covered in this document - page 141

  http://www.Cisco.com/en/us/docs/Telepresence/endpoint/MXP-series/F9/administration_guide/mxp_series_administrator_guide_f90_excl-full-menu-structure.PDF

  You also need a release F9 key.

• Cisco telepresence edge 95 HD cam precision

  received nine edge 95 MXP and HD precision 720 p HD camera ket, after plugging the cable light received from the camera... He showed Please reconnect camera. After having plugged back sound now does not show all the lights on the camera as its not powered everything.  Monitor displays 4 errors, but can't see all the details of the error as remote is unusable because of the camera. tried both cable between the camera and Codec (RS232 - RJ45 2 m / 5 m)

  Any help appreciated

  Thank you

  Hi Hardik,

  Please make sure that you make the connection as shown below:

  

  You can then try to restart the codec and check if you see any light on the LEDS of the camera.

  Please you telnet in the codec and check the status of the camera with the command: camera xstatus.

  It appears as connected real?

• MXP 75 to 95 MXP Upgrade / license question

  Hello

  I want to improve our edge 75 MXP to edge 95MXP.

  We have the following license.

  85-EDGE75 L

  L EDG75-BW2

  L. 95-85-SM

  LIC-S50000-K9

  In what order upgrade.

  Thanks for the help,

  Stefan

  Hello Stefan,

  Basically, L-EDGE75-to-85 is used to convert it to a 95 edge and the bandwidth option is also required. What you need to do, is first add button option & key of bandwidth using the Web user interface. Once this is done, you can connect to the API and use the following command:

  ProductKey [Key] (press ENTER and restart the codec)

  where [Key] is L-EDGE75-to-85.

  When she returns to the top, the process must be completed.

  Hope that answers your question.

  Kind regards

  Saint André

• 1700 MXP not respond remote control

  Hello

  One of my clients has problems with their codec MXP 1700.

  It no longer meets the remote control. They tried another remote of an edge 95 MXP that does not work either.

  The two remotes work with the decision of edge 95 MXP on batteries or a remote control problem.

  The remotes are the two TRC 4.

  I checked the deployment guides and admin and it says that the only way you can tell a MXP stops responding to the remote control is to Kiosk mode and select this option. The device is not in Kiosk mode.

  I have RMA had the codec. They have received a new and configured it but they have exactly the same problem.

  Here, any help would be greatly appreciated as I really don't want to have to do another RMA.

  Thank you very much

  Luke

  Check the following to ensure the functioning of the TRC4 remote:

  Control Panel > Menu Settings > KIOSK MODE SETTINGS > ALLOW the USE OF THE remote CONTROL: WE

  Control Panel > Menu Settings > KIOSK MODE SETTINGS > KIOSK MODE: OFF

  Once you have confirmed that ALLOW USE OF REMOTE CONTROL is enabled, you can use the shortcut key to activate the Menu.

  • Press the phone book 5 times and then press 2.  You should now be able to navigate in the menu of the MXP using the remote control.

  You can also increase the remote control IR signal, if necessary.  To access the switching of IR signals, you need to remove the cover of the batteries and batteries (see attached image) on the remote control.

• Help! Necessary to allow the call in our system, we may not know

  Here's the context:

  I am a tech who was hired to take over for a guy making stuff IVC for virtually his entire career.  He left things in a bit of a mess (no one was allowed to touch "his" equipment, so no one here can help with patterns as they are all used for Polycom and never touched the things T berg I for my Department).

  I'm just getting started in the field of the specific CFI and think I no longer understood.  I'm pretty much familiar with outside edge 95 MXP and 6000 s that we have here, and I crawled around in GK and the BC we have and I am confident that things work well and I know that most of what is what and how it works.  A week after I started, Codian MCU 4210 we had died (there is no configuration file not registered nowhere and there are no impressions by - the settings tab), so I rebuilt using the Codian help website.  Our current facility is some 95 MXP, 6,000 s, a GK Tandberg, Tandberg BC, a TMS and a Codian MCU 4510 Server (we have upgraded after the 4210 died).

  The problem I have is that our MCU can yell to the other participants in many other places, but for some reason that I can't seem to call for a conference that I put in place.  My predecessor had put the things down and would not allow upcoming calls.  Only outside.

  In any case, I would like to know if anyone has any advice on what I should look for to which release.  There is no sense for me to have locked down it tight.  It makes more sense for a party that disconnects to be able to try to reconnect on their own instead of my technicians trying to recall.

  Anyway, any help/pointers would be great.  Let me know the info you will need.

  Thank you

  Luke

  Yes, that seems correct.

  Depending on your network media traffic configuration will change also.

  Before the media could have endpoint to endpoint, with vcs-e and h460.18/19

  you will have the vcs e hairpin.

  We have style Codian MCU running on a public ips connected to vcs - are and it works fine.

  But you must have media ports will also be open to the public internet.

  It should always be possible to use your gk (at least if its on the newest software WinCC and vcs to build an area,)

  but then, you're part of the show of your old

  But I have not tried that for a long time if I'm not sure how that works with the current vcs release.

  Please remember useful frequency responses and identify useful or correct answers.