TC Wan

Similar Questions

• Cable modem has no WAN port

  I have XFinity for my cable and internet services.  We just moved into a house built in 1850 and due to the size of the House and horse hair plaster, upstairs gets very little signal WiFi.  I want to extend the reach of WiFi and intended to do with a couple of Airport extreme.  The only problem is, every tutorial I watch shows the first Airport Extreme being plugged into the WAN port on the modem cable suppliers.  My router/modem, made by Cisco, has no port Ethernet WAN port only 4.  Can I connect the Airport Extreme on port 1 and then put in place using the Airport according to normal or need a WAN port?

  If you have a modem/router, then you would connect an Ethernet cable from one of the four ports Ethernet LAN <>-... choose any you want, they are all the same... to the "O" on the AirPort Extreme WAN port.

  Then use Configuration utility of Apple AirPort "Wizard" to configure AirPort Extreme to create a wireless network that uses the same exact wireless network and the same password that the wireless Cisco uses.

  The wizard will apply automatically other correct parameters... Mode Bridge, by example... so you don't have to worry about things like that.

• What does this mean and how to fix: the router address you entered is not compatible with your WAN IP address.

  I connect to an access provider via Airport Extreme, which is extended through two Airport Express.  When I try to edit anything in one of these devices, even a name, I get this message: "you have entered the address of the router is not compatible with your WAN IP address.  My connection seems to work, but there is clearly something wrong with her.  The Express has no DNS and will not update without the same message.  I have no idea what this is all about and will greatly appreciate the ideas.

  This means that WAN Setup does not or does not install across the network.

  The best way to solve this problem is beginning on...

  Reset all three at the factory and reconfigure each in turn. Do the extreme first and make sure it works... Then add the express.

  If you need help with that we will need to know which modem or modem router to your ISP gave you and possibly the type of services to wide band... and who is the provider.

  Give us screenshots of each installer as you do.

• Transport CANADA share disks over WAN

  Hi, here is my setup:

  I have the DSL modem/router (cannot access the administration panel (ISP does not give) - so it must be in router mode acting without DHCP) hooked up to my no. 1-2 to time capsule (latest model, latest firmware 7.7.7 - in Bridge mode - acting as a dhcp server).

  My 2nd time capsule, also of 2 TB, latest firmware 7.6.7, is connected to the extended bridge ethernet mode (mode dhcp client) 1 St time capsule.

  I installed all the capsules of the time with the overall dynamic hostname and entered my apple for the CCMM ID (green light is on in the airport utility).

  Now the problem is when I connect to the external IP I can properly connect to the 1 St time capsule and browse files, backups, etc, but I can't connect to my 2nd time capsule of the external IP address.

  The two time capsules appear fine in the finder when I'm off the LAN, but it does not connect to a 2nd.

  What is the problem? Am I missing something?

  Part of the discs on WAN is not an option for me as I said I can't put no.1 Time Capsule in router mode due to my ISP give me admin for my DSL modem access.

  Thank you

  Your problem is that the two TC are on the same (your public WAN) IP address and the same ports, according to the standard CCMM. So the first TC in the chain is the one who gets the attention and captured the port.

  Apple didn't CCMM system able to cope with two of the devices themselves I guess.

  The usual way around this kind of thing is to use a different port. Unfortunately, Apple has hidden everything and so there is no way to connect to another port.

  The only solution I can think to... other than the simple move all the files you want to the first TC... is to use VPN not CCMM.

  Buy a VPN router... What are cheap... type of SME end pretty cheap, you can buy or you can buy a router in most common domestic type and run it to third person (dd - wrt, openwrt, Gargoyle, etc.).

  Once you have established a tunnel in your local network, then all in the local network is fully accessible.

• Path of Time Machine LAN and WAN

  Hello

  are the possibilities to two paths setting in Time Machine?

  I need to connect different network in my LAN and WAN net.

  Lives

  If you are an experienced user familiar with the shell, you can add a unicast domain name or IP address to the list of destinations used by Time Machine backup. It will then use the server as long as it is accessible on the network. If it's a good idea or not depends on the circumstances.

  Find the verb 'setdestination' in the tmutil manual page (8).

• Configure via missing WAN

  So I try to implement my 4th gen airport Time Capsule Version 7.6.7, for use with a server that I can access via the internet. I've seen many tutorials that say I need to activate the configuration over WAN.

  

  The image above is of the previous version of the utility AirPort and not my system.

  Here's what it looks like on my system:

  

  How am I able to get it set up on Wan and does not remove anything? Soon, any help would be wonderful!

  Thanks in advance!

  There may be some configuration of remote access options in this article: AirPort Disk - access remote (3 methods)

  In addition, the WAN configuration option is available on your base station? May need to set up there.

  Hope that there is something of value here.

  Take care

  JB

• I have wan to convert MIDI to MP3 on ITunes files

  I have wan to convert MIDI files to MP3 on ITunes Mac OS X El Capitan spirit

  Hello. Have a look here: http://www.wikihow.com/Change-a-Midi-File-to-a-Wav-or-MP3-File

  You can also use a third-party converter available on the App Store.

• I wan to save my history Web sites, but my computer does not record. I go to tools &gt; options &gt; privacy and try to "save history", but it goes back to "use the custom settings for history"... I'm all down on those checked so it should save, but it do

  I wan to save my history Web sites, but my computer does not record. I go to tools > options > privacy and try to "save history", but it goes back to "use the custom settings for history"... I'm all down on those checked so it should save, but it doesn't.

  Thank you for taking the time to help me!

• The WAN Port is communicating with the Ethernet switch?

  I have a Comcast gateway that the router is disabled in so it acts only as a modem. This is related to an Airport Extreme, which serves as my router via the WAN on the AE port. I created a different WAP with a Capsule temporal from the airport, located downstairs with an Ethernet cable from one of the Ethernet ports on the AE to the WAN on the TC port. I think it's what we call a 'roaming network.

  My question is, can I connect my switch Gigabit 8 ports in one of the Ethernet ports on the TC to complete connections wired to all devices connected on it, or should I first connect EI to the switch 8 ports and then connect the switch to the port WAN TC to complete my network "roaming"? In other words, plug it into the port WAN AE or TC still allows you to use other Ethernet ports as a switch?

  Thank you!

  can I plug my Gigabit 8 ports switch in one of the ports Ethernet on the TC to complete wired connections to all devices connected on it

  Yes, assuming that the TC has been configured to run in Bridge Mode, which would be normal.

  or should I first connect EI to the switch 8 ports and then connect the switch to the TC WAN port to complete my network "roaming"?

  It would be considered preferable to wiring, if it is convenient to do so.  For example, in the configuration of the wiring in the previous example just above... If there is a problem with the time Capsule, then all devices connected to the switch to the time Capsule would have a problem as well.

  If the switch is connected to the AirPort Extreme, and the TC is then connected to the switch... If the TC has a problem, the other devices connected to the switch of will not be affected.

• Exrteme AC WAN slow airport

  Hello

  I encountered the following problem:

  If I test my internet connection directly with PPOE connection since my MacbookPro get 900MB or more download speed.

  If I'm testing with the router (with the same cable) I get only 250 MB speed.

  Any ideas what might be the problem? As far as I know this model has 1gbit WAN port.

  Thank you very much

  Zoltan

  Any ideas what might be the problem? As far as I know this model has 1gbit WAN port.

  Yes, it is... but NAT in router is not powerful enough to manage gigabit connections...

  I'd say you're still shy of the number... I expect about 400-450Mbps as the best, that the processor can handle without hardware NAT.

  The problem is firmware Apple removes material NAT... and without it the speed decreases considerably... but you probably other things running that is causing slow downs.

  For very fast router flow watch list in the table Smallnetbuilder.

  http://www.SmallNetBuilder.com/tools/charts/router/view

  Apple Airport extreme is in the list... a long long way down. Place about 80... with prices upwards... the design is now 4 years old and simple fact is that they have been exceeded on all fronts.

• NB100 Wan without wire - LED system

  To press the Fn + Wireless WAN, t he WAN SYSTEM LED is not visible. Is - this is not unusual? The
  Bluetooth sign shines red. Is it necessary that the key WAN shines green if I conect to my WiFi router?

  I think that the LED W - LAN is red. FN + F1.
  FN + ^ is bluetooth. I have the nb100 without bluetooth.

  Greetings

• Satellite T110-10 x - LED WAN wireless turn does not on

  Hi guys,.

  I have this model * T110-10 x * and I was wondering what should the front LED for Wireless WAN should be flashing or turning?
  It comes to the specifications of the model page:
  [http://eu.computers.toshiba-europe.com/innovation/product/Satellite-T110-10X/1076616/ | http://eu.computers.toshiba-europe.com/innovation/product/Satellite-T110-10X/1076616/]

  I bought the USB 3 G modem which works fine, but I was just curious to know if the laptop must have a built-in 3G modem, and if yes, what is the meaning of the key FN and the LED as this model does not have a built-in modem.

  Thank you.

  Hi mate

  Please take a look in the user manual which must be preinstalled on the laptop.
  There is information that the FN buttons in combination with the F1 - F12 keys would have enabled some features/options.
  The WAN/Wlan can also be switched on and off using the FN key!

  >.. .should forward for Wireless WAN LED should be flashing or rotating
  The LED must be lit and it not blink...

• WAN card on 1800-712

  I just installed service pack 2 and now my wan card will work only if I restart my computer, not a startup from sleep mode.

  I get a black mark in a yellow circle next to Manager wan indevice card and the usb port is disabled.
  well work until sp2 has been installed.

  Paul

  Hello

  Well, it seems that the question of the USB is a Microsoft Windows problem.
  I found this Microsoft page:
  http://support.Microsoft.com/?ID=870893

  Also try to repair the connection to the local network. Please go to the State of local connection Area (right click then status) you should find a tab Support. You will find a repair option.

  Good bye

• Use WAN connected airport Time Capsule as a wireless access point

  I had to replace a failed 4 Gen Time Capsule. I tried to install a new Gen 5 airport TimeCapsule via WAN and set up the airport to act as a wireless access point. It is installed in an area of my house with wireless coverage. In the network of AirPort Utility Mode section, I chose "extend a wireless network. The TC is restarted, I get an error message cannot find the intended wireless network.

  What I lack?

  "Extend a wireless network" is a parameter that is only used if the time Capsule need to connect to another router from Apple with the help of a Wi-Fi connection.

  You use Ethernet to connect, you must use the parameter to "create a wireless network. Use the same wireless network name and the same password as your "primary" router

• Satellite A660-047 - lack of WAN Miniport drivers

  I have a Toshiba Satellite A660-047 PSAW3C-047017 running Windows 7 Professional 64 - bit.

  I just downloaded Norton Ghost 15 ISO, created the installation CD, installed Ghost and ran the validation pilot of the installation CD. I received the following message:

  > Following devices have no drivers in the Symantec Recovery Disk.
  >
  > WAN Miniport (IKEv2)
  >
  > Detailed information on these devices are given below
  >
  > Description: WAN Miniport (IKEv2)
  > Class: Net
  > Class Guid: {4d36e972-e325-11ce-bfc1-08002be10318}
  > Material Id: ms_agilevpnminiport
  > Material Id: MS_AgileVpnMiniport

  It seems a little research on Google, it's more than a level higher than a real hardware device interface. I don't really know what it's for, or what is the probability I will miss it in the case of a recovery. Should I spend time worry right now?

  The thread said http://answers.microsoft.com/en-us/windows/forum/windows_7-hardware/wan-miniport-sstp-driver-problem/f83493ae-8127-47dd-a7b7-7e5b3460b6a6 should not 'more often' but I was wondering if exceptions could be encountered during recovery (when I want to use WiFi to browse and restore my system to the State non - factory, as well as to make diagnoses on a HARD drive may be bad).

  Hello

  AFAIK Miniport WAN is a part of the Ethernet controller and you will need to install the LAN / Wlan driver.
  You should go to control panel-> network-> Lan-> properties control.
  Here, you should check if all protocols are installed.

  But as you have already said: it of not really a necessary point

• Re: Satellite C50-B-13D - cannot find the Win 7 drive wireless and WAN

  Hello

  Basically, my problem is that I do not find a wan driver and wireless for my laptop.
  I tried every single driver out there but none of them worked.

  I use a Toshiba Satellite C-50-B-13 t with windows 7 x 64 and the Atheros AR956x Wireless Network Adapter network card, I would be grateful if someone could help me :)

  Hello

  I think that the LAN card is Realtek RTL8106E ethernet controller and the wireless network card seems to be Atheros. The model detailed isn t I known

  Please check this Toshiba WLan portal for Atheros WLan driver for Win 7
  http://APS.toshiba-tro.de/WLAN/?page=downloads

  I hope that the class driver would work. Feedback would be appreciated.