Tecra A11 - 11 H - error: RTC power failure

Similar Questions

• ESX error after power failure.

  Hi all

  I am desperate because this weekend we had a power failure and two of our ESX VM cannot start.

  E-mail error is "cannot open the disk...". »

  Reason: Error handler e/s no valid.

  What can we do?

  A big thank you in advance.

  Check your store for data, the VM configuration, disk descriptor (hard) or anything related to your storage space.

  You can try to create the new virtual machine, add new vritual disk to existing aid & turn on the virtual machine...

  VMware newbie...

  Zen Systems Sdn Bhd

  www.no-x.org

• Re: Tecra A11 - 11Z goes on with power adapter only

  Hello

  My Nooteboom only lights up when I connect the power adapter, 30 seconds to turn off, do not see anything on the screen! Tahnk you

  To be honest I did not understand very well your ad.
  Can you please tell us what exactly happens when you press the power button / stop?

  What was your last action before you noticed this problem?
  Have you updated BIOS or maye some hardware component?

• Tecra A11 - VAP installation failed on Win 7 64 bit error 0x8146045B

  Hello

  I need help. The flash on my phone card tool was out of use. I downloaded the value added package in the 1.3.5 version and tried to install. Installation fail after having extracted the Exe file compressed with the error "Setup PVAT error. [0x8146045B] ". I thougt the error may occure while I not remove the installed software before. So I uninstall the value-added package. After reboot and without installation of value added new package the same error.

  How can I install value added package again?

  Tecra A11, Windows 7 64 bit

  Concerning
  TS

  Hi TSAGI,.

  I had a similar problem with the package of added value, so I also removed the previous version first. But after the reboot, I used the freeware CCleaner tool to clean the registry and delete the old keys of VAP. So just download CCleaner and run it, after this restart again and try to install VAP.

  Check this box!

• Error code 10 cannot install Maxtor 3200 after power failure

  Original title: maxtor 3200 code 10

  After a power failure cannot not re install Maxtor 3200 get response Code 10

  Hello

  The Code 10 error code is generated when the Device Manager has not enough information or error that spread upwards by device drivers is not recognized by Device Manager. In addition, this error may occur if one of the pilots who needs the unit does not start. If multiple drivers are used by a particular device, it can be difficult to determine which failed.

  I suggest you run the FIXIT from the link below and if it helps. You can also follow the manual steps and check.

  Description of errors related to the 10 Code that generates the Device Manager in Windows on computers

  http://support.Microsoft.com/kb/943104

  Hope this helps and keep us posted.

• Error in the application of Muse after startup after a power failure

  Hello

  I had a power failure and after I got the following error:

  The msg box is modal, and the ok button does not work, then the application is frozen.

  

  I tried to re - install the application twice, but without a bit of luck

  Advice would be appreciated.

  Brdgs

  E Bjarn

  Hi Bjarn

  Have you tried to create a new site, and see if it crashes too when opening. If it works fine, your file may be damaged .muse.  In addition, where was located, as the network drive or local file drive?

  Please share your with us .muse file to study? Please send it to [email protected]. If your file is larger than 20 MB, you can use something like Adobe SendNow SendThisFile or Dropbox. Don't forget to mention the link to this forum thread in your email so that we can identify the file.

• I had a power failure and I learned today that there is a problem with the cache and I need to go to Preferences, purge the cache. I did this, but get the same error message every time I open the subsequent times of bridge.

  I had a power failure and I learned today that there is a problem with the cache and I need to go to Preferences, purge the cache. I did this, but get the same error message every time I open the subsequent times of bridge.

  Mac or PC? Version of the OS? What version of CS?

  Have you tried to reset the bridge? CTRL (Windows) / Opt (Mac) + click on the bridge to start icon and select open boxes.

  Otherwise, you could manually delete the cache, but we need to know the answers to questions to say where he is.

• Tecra A11-110 (PTSE1E) does not load

  Hi all

  Recently my laptop stopped charging.
  The battery is new and worked for a while. It works on another laptop.

  When I connect the charger, the laptop gets power, but it does not load. I guess it's always work around.
  Is this a mistake in any sensor motherboard?

  How can I fix?

  Is the motherboard 'dead' (for this purpose)?

  Thanks in advance.
  See you soon,.
  Hugo.

  Have you noticed the problem of load using the old, original battery?
  If the old battery may be charged correctly, I don't think that there is a problem with the laptop.

  You said you have tested this new battery in a laptop.
  Have you tried using another model Tecra A11?

  Your comments would be appreciated.

• Tecra A11 - 17 C - impossible to boot from LAN

  Hello

  For the last few days I worked on a Toshiba Tecra A11 - 17 c PTSE0E - 02W01GEN.

  I work in a school and we have about 15 of these laptops. I was not the person who did the origonal installation and this person has not left.

  One of the computers needed a re - build. We use an installation of LAN to windows 7 so I put prioraty device that the network card, save it and re - start.

  Then, sometimes with the error PXE - E61 Media Test failed, check the cable.
  Now, I know the NIC works fine beuse it worked before I did any messing around.

  I then checked the other laptop and I get the same error PXE - E61 Media Test failed, check the cable and they all fully functional network ports.

  So I thought ok there is something in the BIOS.
  I found nothing apart an Enable lan option that is enabled.

  It was suggested to relax the default BIOS and then format the hard drive.
  So I thought ok well first I'll try it with the BIOS reset if that does not work, I'll do a format.

  So after that it does not work I thought Okay I'll just clone your laptop work with clonezilla.

  Do I get to the windows flag then instantly the blue screen of death, I can't read it so I is much too fast.

  I thought ok I swap hard drives with the work there. The boots work the clone hard drive just fine without error at all, but the work PC hard drive load the windows flag then blue screen of death.

  I then used a product recovery disc now, it's a drive of windows XP is usless. But I did anyway, and same thing again, it turns the disc fine install XP fine but the flag windows and blue screen of death.

  I finally intertwined a hardrive work 1 different working laptop and a same new blue screen of death in wondows flag.

  It seems to me there must be something on the bios that is
  (A) stop the network port in the bios
  (B) stopping the different hard drives to work in the laptop, even if it's exactly the same laptop.

  They built from the network before for the wondows current installation works, but I have no idea what to do now.

  The error PXE - E61 Media Test failed, check the cable means that the laptop has attempted to boot from LAN, but the configuration of the installation could not proceed.
  Why?
  I m not very well why, but probably there is something wrong with the PXE server settings, etc.

  Are you sure that PXE server has been correctly configured to 100%?
  If this is not the case, check this box.

  > I then used a product recovery disc now, it's a drive of windows XP is usless. But I did anyway, and same thing again, it turns the disc fine install XP fine but the flag windows and blue screen of death.

  Always is Win XP installation could be completed, and this means that the HARD drive should be ok.
  The BSOD could be due to incompatible software or wrong / driver that is part of the recovery disk

  Are you sure that the Win XP Recovery disk you used was the right one?

  How about installation using charge Windows 7 system using the disk of Microsoft?

• HP 280 G1 (N9E78EA): Partition disappears after power failure, watch now unallocated

  Hello!
  I have a PC
  HP 280 i5 - 4590S G1 / 8 GB/500/DVD-RW/W10P + 7Pro64
  and
  Pro series SSD Plextor 128GB 2.5 "SATA SSD M6.
  
  Partition disappears after power failure, watch now unallocated.
  I tried to use TestDisk to see what was going on. After crossing the 'Analysis' command and deep research, but the partition disappears.
  Any suggestions on what I should do next?

  Your SSD have lost files due to the power failure system sudden. I suggest you run CHKDSK to fix this error. Also remember, if the data stored in your SSD are important to you, then first the software of raw data as WDR pro of stellar phoenix recovery and then apply diagnoses to repair.

• Tecra A11 - 1F4 (PTSE0E-OM6052EN) which XP AHCI driver?

  I am trying to install the drivers for XP on a Tecra A11 AHCI;

  I have a ghost image that loads on this laptop in compatibility mode in the BIOS and I try to update the driver for the drive in AHCI controller, restart & change the disk to AHCI mode in the BIOS.

  That's what I usually do for HP laptops, we have, and it works most of the time.

  Storage power Toshiba drivers are in the form of an executable that will only work if you have AHCI enabled, how anyone runs in compatibility mode supposed to use these?
  They don't even extract driver files, you can use only the .cab files and an installer.

  I have listed in the device under IDE ATA/ATAPI controllers Manager;

  Intel (R) 5 Series/3400 Series Chipset Family 2 port Serial ATA Storage Controller - 3B2D
  Intel (R) 5 Series/3400 Series Chipset Family 4 port Serial ATA Storage Controller - 3B 28
  Primary IDE channel
  Primary IDE channel
  Secondary IDE channel
  Secondary IDE channel
  3 entries for Peter card reader &

  Intel drivers, I downloaded from-

  s http://downloadcenter.Intel.com/Confirm.aspx?httpDown=http://downloadmirror.Intel.com/21730/eng/f6flpy-x86.zip&lang=eng&DwnldID=21730&DownloadType=Driver & OSFullname = Windows + XP + *.

  .. .and it gives me the list of controllers to choose;

  Intel (R) 5 Series 4 Port SATA AHCI Controller
  Intel (R) 5 Series 6 Port SATA AHCI Controller
  Intel (R) 5 Series/3400 Series SATA AHCI Controller
  Intel (R) 7 Series Chipsets SATA AHCI Controller
  Intel (R) 7 series/C216 Chipset Family SATA AHCI Controller
  Intel (R) Desktop/Workstation/Server Express Chipset SATA AHCI Controller
  Intel(r) ICH10D / DO SATA AHCI Controller
  Intel(r) ICH10R SATA AHCI Controller
  Intel(r) ICH7M/MDH SATA AHCI Controller
  Intel(r) ICH9M - E / M SATA AHCI Controller
  Intel (R) Mobile Express Chipset SATA AHCI Controller

  The device ID of the controller (Intel (R) 5 Series/3400 Series Chipset Family 4 port Serial ATA Storage Controller - B 3, 28), I'm trying to install the drivers AHCI is;
  PCI\VEN_8086 & DEV_3B28 & SUBSYS_00011179 & REV_06\3 & 115 83659 & 0 & FA

  Please can someone tell me which of these to use with the above material?

  It takes me ages to build, install, bluescreen & rebuild to try again...

  Thanks for sharing!

• Tecra A11 won't recover/restart of sleep

  Hi guys,.

  I have a TECRA A11 model no - PTSE1A - 00M 005.
  It has Windows 7 Professional 64 bit and is up-to-date on all windows update.

  When I click the power button and send it to sleep (power button / stop is set to sleep) or close the cover and he goes to sleep, I can't click the power button again and recover or restart from sleep. It doesn't do anything.
  Power, power sector and battery plug lights up green but the hard drive does not start, or I do not see the hard drive Led light up.
  I have to keep the power button for 5 seconds to stop the laptop, and then restart it.

  In addition to this, I also have times when the computer is turned off correctly, but when I go to start it, it won't start. As usual the left 3 lights, but the hard drive light does not illuminate. The fan starts, but the computer will not start. I have to press the power button again for 5 seconds for the computer, close and then restart. The second time round it always starts.

  This problem has me baffled for a while now and I can't find a solution for this.
  Any help would be much appreciated.

  Thank you

  Since when did you notice this kind of behavior?

  Try please set the BIOS to default settings and check the startup problem.

  FN + F3 to put the laptop into sleep mode, close the cover and after a few minutes open the cover and press the power button. The same problem happens again?

• Tecra A11 - cannot burn CD - R

  Hello

  My Tecra A11 with Win 7 Pro 64 and a carpet * a DVD-RAM UJ890AS is not able to burn on a CD - R. CD - RW and DVD no problem, but when you try to burn a CD - R I got following error Code: 060277-26 - 2A 031000

  I tried the solution in
  http://forums.Toshiba.com/T5/computer-troubleshooting/error-code-380381-26-2a031000/TD-p/172666
  -without success. There is no filter in case key in my registry.

  I have tried 3 different brands of CD - r, I tried CDBurnerXP and the Toshiba Disc Creator - still the same error. It is written (copy of a music CD) track list, then the error pops up. The CD - R is not usable more after that.

  What can I do? Is it possible to Flash the firmware of the drive from DVD - if yes, where can I get the fw?
  Thanks in advance!

  Hello

  Have which brands you tried?
  I use TDK R and they work properly.

  In addition, I recommend the alcohol laser lens or cotton cleaning tip.
  Has also had problems reading and burning the discs that have been fixed after cleaning the lens.

• Tecra A11 speed on the fan at 100% all the time

  Hi, one of my colleagues has a new notebook Tecra A11. I've recently updated the bios to version 2.60 and since then the fan is constantly at full speed. Before the update it would be noticeable when the laptop has been widely used, but would slow down when idle. Anyone else seen/had this problem? I wouldn't mind flashing back to the old bios but can not see available on the web site of tosh.

  Thank you

  Hello

  In your case, I recommend setting the BIOS to the default value.
  You can do it in the BIOS. Insofar as I'm sure you could get press F9 default.
  But the option is mentioned in BIOS to verify this.

  In addition, I recommend changing the CPU and cooling module in Windows Power Options.

  This should help to reduce the speed of the cooling fan.

• Tecra A11 - cannot start the BIOS update

  Hello

  I downloaded the latest update of the Bios B2.50 - EC1.80 for Tecra A11-127 (PTSE0E. Wenn I start installing, an error occurs: "this computer is not supported", but my laptop is an A11-127 with Partnumber PTSE0E, why it doesn't work?

  Why is he not possibel to download an old Version of the Bios?

  JSpindler

  Hi jspindler,

  The question is why you want to update the BIOS? This update should be carried out only if it of really necessary. In addition, only the most recent update of the BIOS can be downloaded as it fixes most problems.

  In any case, you need to start the BIOS as an administrator and you should decompress all files from zip archive before start you. Also, make sure that the value added package is installed.

  By the way: what operating system is installed?