Tecra M1 Autoexexec problem

Similar Questions

• Tecra A2 - mouse problems

  I have some problems with the external mouse on my tecra A2. The pointer seem to 'jump', sometimes across the screen, and it's pretty boring. I'm not sure of what the cause of the problem and still less what to do about it... The mouse is a Logitech optical mouse. I tried to change to a similar mouse but that did not help...
  What should I do?

  Hello

  Try disabling the touchpad through FN + F9. Did you try it with mouse just wireless? You can try it with the mouse that is connected with a cable?

  Sometimes I have the same problem, but it happens if the batteries are empty or if the mouse signal receiver is placed on the wrong place.

• Tecra A2 Sound problems

  I bought a second hand Tecra. I can't play any sound out of it. When I go to sounds and Audio, under audio devices, it says "no Audio device". When I go in the material, he said all devices work correctly except for the Multimedia Audio Controller, which according to her, the "drivers are not installed (code 28). When I try to install the Realtek drivers AC 97 system said that they are not compatible with XP and landfills eventually get out me.
  Can offer you any advice / solutions to this.
  Thank you very much
  Melody

  Hello

  This is especially a problem with driver. Go to the page of the Toshiba driver and download the audio driver for your model:

  http://EU.computers.Toshiba-Europe.com/innovation/download_drivers_bios.jsp

  Install it and then restart.

• Tecra M4 boot problem - missing or damaged ntoskernl

  Hello

  I have a Tecra M4 running Windows XP Tablet Edition, which fails to start due to "a missing or corrupt ntoskrnl.exe. According to the MS website I can solve it using the installation disc, but I don't have one that I bought the laptop from my employer when I retired. I was told that my installation is legal and have the license number.

  I tried to get a Toshiba drive, but it seems that the machine is too old.

  Anyone know where I can get a drive to. If it is not possible to find the same version of the operating system can I can use an installation disk XP Pro standard (I could buy on the Internet), even though my system is the tablet edition. I don't want to take the risk to wipe my data, because even though I have most of the stuff saved there are has some important issues that are not.

  Any help appreciated.

  Thank you

  Barbara

  Hey,.

  Yes, that is a known issue regarding the ntoskrnl file and you need a Microsoft Windows disk to fix this problem in the repair console.

  Are familiar you with Windows repair console? I ask this question because you need to use the DOS command line based to solve this problem, there are GUI. If so ask a friend if they have such a drive and normally the professional XP disk should also work.

  Otherwise, you will have to reinstall the whole system :(

• Reader of SD with Tecra M2 driver problem

  Hello

  I formatted my laptop: TECRA M2 PTM20E-0R1LZ-FR / PM 735

  I found all my drivers for all execpt for the SD reader componet.

  It was very difficult to find the SD host controller, but I finally found it:
  Toshiba Secure Digital host controller
  oem17.INF:Toshiba:SDHost:6.0.4058.0:pci\ven_1179&d ev_0805

  But now, when I insert my SD card, I have a problem with the SD reader driver.

  So, if anyone has an idea...

  I did all the forum, all the driver toshiba support page and nothing on that kind of driver.

  Thanks for your help.
  Kind regards
  xVZx

  What type of problem do you have when you insert the SD card?
  Do you use drivers from the Toshiba support page?
  Do you use took in charge a card SD (support capacity)?

• Tecra M2 - monitor problems

  You just bought a Tecra M2 three days ago. When I turn on it almost every time is delivered with the message, the program Nvidia? could not be closed. Whem twice I turned on the pc, the monitor has been with strikes. Who is wrong?

  Hello

  If your laptop is all new contact Service partner and they can check what is the problem with your monitor. Normally avoid any strike.

• Tecra M2, sound problems

  I can't get any sound on my tecra m2 at the present time. Its been like that for a few days. The volume is not cut or something like that and I can not see what is the problem, can anyone help?

  Have you tried to turn the Volume control on the front of the Machine?

  Good bye

• Tecra M4 - battery problem

  Hello

  My Tecra M4 battery appears to discharge on his tours off the coast. If I charge it to 100%, then unplug it and don't use it for about a week when I come to turn it on it used and I need to connect to the mains. When he dose get Windows reports 0%. It seems to lose about 15-20% per day of power turns off.

  Anyone know if this is normal for this model of if there is probably a problem that I have to look at the dose.

  Thank you

  David

  Hello

  This is definitely not normal. I think you need a new battery. That this be enabled by service. You still have warranty, so it will be free.

  Good bye

• Gravity is HARD on my Tecra M1 disk problem?

  I have a Tecra M1, 1.6 GHz, MS Windows Xp sp2.
  Last week, I posted a message to describe the problem of my computer. He started very slowly every time I restarted the computer. I logged on and there were Windows to notice that my system has problems.

  I ran several application software and a full blue screen came out with some opinions, such as

  KERNEL_STARK_INPAGE_ERROR

  .
  STOP.

  I reinstalled the OS using the supplied CD receovery. My computer seems to be OK.

  However, I installed the version of Norton Partition Margic (NPM) 8.0 to creat 1 driver more and the NPM has noticed that:
  «NPM has detected an error 116 on the boot partition at sector 58605120 on disk 1 (the C driver, I invited).» The co-leads starting logical block (LBA) is 58605120 and the value of the lost head sector (CHS) is 1643493. The value of the LBA and CHS must be equal.

  I know not how the probblem is and what is NPM to use to set the value of the CHS.

  Are there any suggestions?

  Thank you very much

  CUONG

  Hello

  Maybe this article can help you.
  Microsoft Knowledge Base. Q315266

• Tecra S1 - display problem, even on external monitor

  One day I was using the laptop, surfing the net normally, everything was fine and suddenly the screen went bad... (photo below). I tried using an external monitor and still the same, so I'm sure that my monitor is fine and it is probably a problem of display card?
  I tried to update my display card driver and no luck, so I decided to use the recovery CD to restore the system and no luck once again.

  Here is a screenshot after the system restore... y at - there a way to fix this without taking it to a service center?
  Thank you
  Link: [http://i130.photobucket.com/albums/p262/ctb205/mon.jpg]

  Hi borist,

  It s really great that you could post a picture of your problem. Thank you!
  In addition, you have already tried a lot of as the recovery facility and an external monitor.

  Unfortunately, it seems to be a hardware malfunction of graphics card. :(

  This means that you will need to swap the motherboard because the graphics card is fixed on it. Motherboard is a party quite expensive and Tecra S1 is old notebook then maybe you can get a second hand or laptop motherboard on eBay and swap it out.

  Good luck! :)

• TECRA 9100 battery problem

  Similar experiences to mine, please?

  After using no not my Tecra for some time (about 3 months). He was once again the charger for more than 24 hours and I'm now done with the original problem, I had the last time I used the Tecra, several months ago! The problem is, I think, only related to the tent to use it on battery, as follows:

  At the start of the machine of 'cold', after passing the request of 'password' screen, it goes straight to a "small blue screen", which includes the message:

  Hardware malfunction

  Call your provider of support material

  NMI: channel check / IOCHK

  The system stopped *.

  A little more information, I found that I can actually 'blue screen' situation - turn off not having don't no need to remove it battery that I first thought - and if I get the power cable then everything starts up well and seems to work normally. If I then remove the power cable (leaving the laundry to run on battery only) the small blue screen and same message reappears.

  Yet once which seems to indicate a battery problem, I guess?

  Has anyone else had a similar experience?

  Post edited by: Gary S Cooper

  Hello

  Windows may indicate a fundamental error messages only when material occurrence malfunction, so that the elimination of the errors can be difficult for equipment problems. Most of the problems of material step in connection with the motherboard, the main memory on a motherboard or adapter or the stamp on a motherboard or adapter.

  On this path, it is not easy to say what may be the problem. I don't know how old is the unit, but if the unit is still under warranty I advice you contact service partner chartered. I'm sure they can find what may be the cause of this problem.

  Good bye

• Tecra 8000 boot problem

  Hello

  I am new to this forum and I hope that its going to be a help. Ive had my notebook from toshiba for about three years, and I think its great. stoped to work 4 months ago and I was just it's bin but I thought it would be a waste. in any case, I thought I'd give it go to see if I could fix or it is better to set.

  The problem is when I start the notebook, it stays on the screen "in touch with tomorrow toshiba" and does nothing else. I can't access the bios it will do nothing. Please someone at - it an idears for what is wrong, if so, please answer.

  I don't really want to throw and if I could get it fixed at a price fair, if everything goes well he will continue for another three years.
  Thanks again and any help would be great

  Hello

  It is not easy to say what is the problem, but in my opinion, it may be material defect. You built in hardware components like new memory RAM or HARD drive?

  If you are so happy your Tecra you can contact the Service partner. They can check and detect if there is some part of material defect.

• Toshiba Tecra 8000, monitor problem

  Hello

  I have a problem with my laptop Toshiba Tecra 8000, there is a green line with a width of 1 pixel on the screen of my laptop which does not disappear. the laptop is almost 2 years old. is there a possibility that it could be repaired? Thanks in advance,
  Mark Kuiper

  Hello

  interesting would be if the green line is permanently on the screen during startup or 'just' that Windows runs.

  But never mind, the laptop Tecra series three-year warranty.

  So in this case you can give it to a Toshiba repair for a control center upward.

  Good bye

• Re: BIOS version 3.30 Tecra A11/M11: problems with Ubuntu systems?

  I just got the updated BIOS version 3.30 on my Tecra A11/M11 invitation.
  I'm still under Win7 now, but plan to add a dual boot with Ubuntu when the next LTS strikes in April.

  Is anyone having problems with the new BIOS?
  Should I upgrade or leave intact 3.20?

  I don't find any evidence of trouble with 3,20.

  Why upgrade BIOS if everything is OK?

  In addition to as much as I know that Toshiba can't stand not the Linux operating system, and I doubt that the new BIOS would improve any Linux performance so, if you are satisfied with the version 3.20, stay with that

• Boot Tecra A4 USB problem!

  I have a Toshiba laptop Tecra A4 PTA42E (BIOS v 1.10 2005-09-26). My
  problem is I can't boot from a USB key. There is no start
  option for usb memory stick. Is it possible to do?

  Thank you

  Usually, it is not possible to boot from the USB key.

  But as the previous user has written by pressing F12 immediately after starting the laptop would boot menu, from which you can choose your boot device.

  Best regards