The analyses show no problems, but challenges remain

Similar Questions

• In the analysis of noise problem

  Hello

  I see now a BiQuad filter two steps and I want to know the noise in the axis of the output "out". However, the analysis of noise gives me nothing, but just a black background without any digit or number. What would be the problem? Thank you very much!

  Better compliance

  Billy

  Hi Billy,

  It's a problem of DC convergence in the simulation. In the scan options, select use custom settings.

  

  On the Global tab, the value of the Shunt resistance of analog nodes on the ground [RSHUNT] 1e + 008

  

  On the DC tab, set the iteration DC [ITL1] limit on 400

  

  Then simulate again and now you can see that they are all posted!

  

  

  Hope this helps!  :-)

  Kind regards

• When you use Windows Explorer to view the files and folders, the thumbnails of image files appear briefly then are replaced with the default icon of the image file. I tried the answers to similar problems, but none worked.

  Browse the folders with image files, I cannot see the thumbnail icons for images correctly.  I know, it should be possible, but I can't do it.

  When I first open a folder in Explorer, I see the correct images for a fraction of a second, then all images are replaced by the thumbnail of the image file (which looks like part of a digital SLR).
  I put all folders to display picture to display the preview and the filter, and the "always show icons never thumbnails" is not checked.  Display file icon "on the photos' is unchecked (I tried checking, too, without change).  I also deleted the thumbnails using disk cleanup as suggested on another question, but which did not allow them.
  The result is that, if I want to open an image for editing or downloading, I have to use a third-party application (for example, Pentax Photo Browser) to preview images, and then return to the Explorer window to select the correct file by name. Don't try to difficulty of these things that are not broken.

  izzlecrate,
  You might want to try it and I just did this procedure myself a moment ago and surprising, it worked!  First of all I must tell you that I have Windows Vista, but the information I got was for Windows 7 and it worked.

  First: You must create a NEW FOLDER and put it on your desktop.
  Second: Move or copy the contents of the original file in the NEW FOLDER on the desktop. I copied the content, just in case something went wrong.
  Third: After that is finished and all the contents are inside you.
  Fourth: On the desktop right click on the folder and click Properties at the bottom of the box.
  Fifth: Click Customize tab at the top and then the Middle click on DEFAULT settings for the folder.  Click on apply to, click OK and your done

  NOW! You can move the folder wherever you want by drag-and - drop the folder and when it's done and that's the best part, you should see the thumbnails of the folder on the EDGE of the folder that you just created.  It worked for me and I hope it works for you.
  I have 10 years of experience with my computer and have troubleshooted my friends for viruses and other computer problems successfully.  I'm advanced computer user.

  That this is done, it restores the folder its original settings.  Good luck! Rick

• I do the buttons on the taskbar show only icons, but I wanted it back.

  what I did before the buttons on the taskbar show only icons is as follows:

  Start > run > regedit > HKEY_CURRENT_USER\Control Panel\Desktop\WindowMetrics

  There, you must find the one "REG_SZ" with the name "MinWidth".

  (write without quotes)

  If you do not create one in your won with the name "MinWidth".

  (write without quotes)

  Once you find it double click on it and set the number 56 then click ok and close.

  Registry and restart your computer.

  
  

  
  

  ---------------------------------------------------------------------------------------------------------

  
  

  minWidth had-255, I changed it back, but the taskbar do not change back. What should I do now?

  
  

  Here's the screen shot a http://oi51.tinypic.com/15dl2pz.jpg link

  
  

  
  

  
  

  
  

  
  

  Use this tutorial: go to an Option and take #2 - restore the task bar button

  http://www.Vistax64.com/tutorials/191509-taskbar-icons.html . for the benefits of others looking for answers, please mark as answer suggestion if it solves your problem.

• Icon in the taskbar shows no Internet, but my connection is working properly.

  Hello guys

  I use Windows 7 Professional edition that is connected to a proxy server. After installing Norton 360, the network icon changes automatically to the image of triangle (no internet access). After this problem I had completely removed Norton 360.I have updated the network driver. Then I uninstalled the driver and reinstalled a fresh driver. The icon shows still no internet but internet access works very well. I don't know what to do. Please report any solution for me. I want to change this yellow icon.

  Hi there are Kumaran,

  I found this link that could be helped to solve your problem. I know that it is quite a long thread but it might be useful to go through the steps.

  An update will be appreciated.

• Filter in the analysis of OBIEE problem

  Hi Experts,
  
  I created an analysis. My field's Bug database.
  
  Details of the analysis:
  
  I get the following columns (Bug No., id tags, product, status, purpose of bug and spinning). The filter I used here was produced id is in (I gave 107 here product ID) and then tags like (2 labels) and then the situation in (6 status codes).
  
  When I run this analysis, I get the following error:
  
  [nQSError: 10058] A general error occurred. [nQSError: 43113] The message returned by OBIS. [nQSError: 17001] Oracle error code: 2395, message: ORA-02395: Appeal exceeded limits on the use of the e/s to the call of the OCIStmtFetch OIC. [nQSError: 17012] In bulk fetch failed. (HY000)
  
  But if I change the filter above or any of the following criteria, his recovery of the values:
  
  case 1: reduce the number of product ID to 104 in the filter, his work
  2nd case: reduce the No 5 in the filter, his work situation
  
  Can someone please clarify, what is the problem I'm facing here?
  I need to change all the options in the NQConfig.INI file or the instanceconfig.xml file?
  
  Thanks in advance,
  Arul

  Hi Arul,

  to create a UNION statement, you must use "combine with a similar request. This creates a SQL UNION statement.

  'Get the filter of another analysis' will create a subselect structure, as this SELECTION A1, A2 FROM T1 WHERE A1 IN (SELECT A1 OF T2).

  Hope this helps,

  Justin

  Published by: justinjtownsend on April 11, 2011 01:34

• If I try to send an e-mail, it remains in the Outbox, showing never sent, but he sends several times.

  Using Outlook Express 6 on windows XP

  When I send an email with an attachment or meet one of my Inbox of the message send by the end of the progress bar, then I get a yellow warning triangle (no error code) and the seat of message in the Outbox to be sent whenever I have send and receive.

  Messages are released (several times which is annoying people), but remain in Outbox marked as pending until I delete them.

  I disabled my McAffee analysis email, but problem remains...

  Help!

  Found a solution, delete all messages in sent items, and deleted messages.

  It would seem that it is a problem of storage.

  I created an archive folder to keep sent messages, I need then deleted the rest.

  This seems to have solved the problem. : )

• Airport utility show that airport extreme has a problem, but it remains inaccessible

  My Airport extreme began to play up.  As you can see in the picture, it seems to have a problem and cannot be opened for editing.  I tried several times to do a hard reset and reinstall my setup.  It works and the network remains functional, but after a few minutes, the Base Station will appear with this warning sign.  Any ideas on how to solve this problem?

  

  A 'solution' refers to those who have set up their base stations for Back to My Mac. If you did, how to follow recommended action is temporarily remove or disable this option, as follows:

  • Run the AirPort Utility.
  • Select the base and then station, select change.
    • Note: You may need to use the option "configure others...". "to access the base station. Enter the IP address of the base station, the default value is: 10.0.1.1 and base station administrator password when you are prompted.
  • On the tab of the Base Station, go back to the section of my Mac at the bottom of the window.
  • If you have entries here, select it and click then the minus sign "-" button to remove it.
  • Click on update and allow the base station restart.

• Nellus91 thank you for the answer to my problem, but site jvl.lbpack... still happens even when I went to open an email message and must remove to continue

  Installed Malaware bytes Anti Malware and it helped but when I went to open an email message "this is a recommended download. Installation takes less than a minute' comes with a link jvl.lbpack... Have to close it this continues. Even came during the use of this procedure of support!
  Can Nellus91 you please help once again

  Problem solved. Thank you
  GeoffSue

• Width of the box shows in DW, but not in the online site

  I'm intrigued by this one though attractive to help save time.  I created a page simple held in www.armadillogames.ca - I created the divs with the width of 980 with auto margins left/right.  It shows properly in DW but on download in all browsers, it seems be ignorning the width setting and display of the page with the text beyond just in front of the 980 defining, in Firefox, Opera and Chrome.  I have built many sites of DW and cannot understand it at all!  I went off the Rails?

  Thank you very much.

  Tracy

  Style sheet link is 404 not found on the server.

  Your code says that it should be here:

  / public_html/amadillostyles. CSS

  But it's actually there:

  http://www.armadillogames.ca/amadillostyles.CSS

  That tells me your site definition is not configured correctly. public_html is a virtual root directory on your server.  It should never appear in your local site definition.  It must be in your remote server definition.  See screenshot.

  

  Nancy O.

• Cannot remove an xbox360 Extender. The status of the Extender shows as visible, but not mount.

  I'm using windows 7, 64-bit computer. I could connect the extender to the xbox, the first time I tried. Then I unplugged the Extender to try to connect to another computer. Now when I come back in WMC, it is picking up the xbox 360 extender, but it seems to be looking for the old 8-digit code. Any time I try to put in the new code, I get the configuration error. There is also no option to remove the extender for the xbox that WMC is recovering. I tried to remove the certificate that is generated. A new certificate is generated every time that I put in the 8 digit code, but still not login... McAfee Firewall is also disabled. Also tried turning off WMC and on again. What Miss me?

  Hi Christophe,

  The question you have posted is related to the Xbox 360 Extender and would be better suited to the Xboxt community. Please visit the link below to find a community that will provide the best support.

  http://forums.Xbox.com/

• receive the following error code when searching for a piece of music I did several times without a music problem but have recently updated Firefax: Fatal error: Call to undefined function AmazonData() in/home/boss/public_html/mc on line 13

  I am in the page web http://www.songarea.com/ and after searching a piece of music, I get the following error message:
  "Fatal error: Call to undefined function AmazonData() in/home/boss/public_html/mc on line 13.
  I did this several times before without a problem, but have recently updated Firefox with the Skype add-on and wonder if the two things are related.

  URL of affected sites

  http://www.songarea.com/

  Hi John,.

  It is an error message from the web server providing this site. Specifically, it is something wrong with their PHP code.

  It is not browser specific and would go into another browser besides Firefox.

  You will need to contact the webmaster of this site to report this problem. A quick test does not show this problem, but you do not specify what search query, you tried:

  http://www.songarea.com/music-codes/test.html

• Keep the LabVIEW window on top BUT...

  Fellow LabVIEW users,

  I have the following rather simple problem, but once again hard. The problem is as follows.

  My main LabVIEW application calls an another VI whose façade is charged when the VI is called. The behavior of the window in the two VI 'Properties of the VI' is 'default'. Now, I want to achieve my newly responsible for façade rest on top. This can be done by one of the 'make window always on Top.vi' in the 'WINUTIL.llb', which can be downloaded here. Now my problem is as follows. I want to keep both of VI façade features . The current behavior is that when I call 'Make window always on Top.vi' I lose the ability to control my main façade.

  Has anyone tried to solve this problem before? It must be possible, I think? Because there are a lot of other windows applications that do not have the behavior I describe in some of the features they provide.

  Kind regards

  Wouter

  PS Of course my OS is Windows

  PSS. I try to make an example now.

  The problem in your example isn't that the window is on top.  The way you call your VI is the problem.  Your main VI call directly your Subvi.  Your main VI will sit and wait for the Subvi close.  You must call the Subvi making a dynamic call to launch a parallel process, so that the main VI may continue to operate.

  I modified your example to show how to do this.

• When I turn on the computer, the screen indicates "a problem has been detected and windows has shut down to prevent damage to your computer.

  Original title: when I turn on the computer.

  the screen shows "a problem has been detected and windows has shut down to avoid damaging your computor.

  Hi Cjdaniello,

  ·         Did you do changes on the computer before the show?

  Follow the suggestions below for a possible solution:

  Step 1: Start in safe mode and check if the problem persists.

  Start your computer in safe mode

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  Step 2: If the problem does not occur in safe mode, you can put your system to boot (in normal mode) to solve the problem.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: After troubleshooting, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

  I hope this helps.

• Hello, I am using windows DVD maker and would like to know thw following: how to add text to the slide show?

  Hello

  The slide show is done but I can't add text can you please let me know if this feature is available

  Hello

  If you use the native windows DVD creation I suggest going through the article in Microsoft and check if that helps.

  Burn a DVD-video using Windows DVD Maker disc

  http://Windows.Microsoft.com/en-us/Windows7/burn-a-DVD-video-disc-with-Windows-DVD-Maker

  (See less to change the DVD menu text)

  See also:

  Work with projects in Windows DVD

  http://Windows.Microsoft.com/en-us/Windows7/work-with-projects-in-Windows-DVD-Maker

  Work with projects in Windows DVD

  http://Windows.Microsoft.com/en-us/Windows7/work-with-projects-in-Windows-DVD-Maker

  Hope this helps and keep us informed if you need help.