The problem in normal mode startup

Similar Questions

• Computer has a black screen with a message "power off, then reinstall the jumper in normal mode position."

  Original title: black screen?

  My computer has a black screen with: turn off power and reinstall the jumper in normal mode position? Help!

  Hi Miguel C.
   
  a. What is the brand of your computer?
   
  b. do you remember of any changes to your machine before the question?
   
  I don't know what motherboard you have, but some is shipped with the 'Clear CMOS' jumper in the position unequivocally. Check the manual of your motherboard for this rider and make sure that it is in the normal position.
   
  J7B1 computer configuration jumper block requires a single rider set the configuration of the BIOS Setup utility. This allows the configuration in the configuration utility BIOS, including the frequency of bus and the processor motherboard speed.
   
  Note: Do not move this jumper with the computer turned on.
  
  Warning of the BIOS:
  BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.
   
  I think, you'd be best to contact the manufacturer of the motherboard as this seems to be a motherboard problem.
   
  Aziz Nadeem - Microsoft Support
   

  [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• DRIVER_IRQL_NOT_LESS_OR_EQUAL normal mode startup problem.

  I have a HP Mini netbook. Everything works fine until there is when a security alert 4 days prompted a Trojan virus had been detected. Thought I had dealt with the problem (ran antivirus scans and problems quarantined). Turned on netbook 2 days ago and after Windows XP Home SP3 message/screen "Welcome" appeared for about 4 seconds what a BSOD is displayed with the following error:

  DRIVER_IRQL_NOT_LESS_OR_EQUAL

  Technical information

  STOP: 0X000000D1 (0XA0223408, 0X00000002, 0X00000000, 0X886D19A8)

  I can load Windows in safe mode with network. I don't know what to do. I downloaded and ran SpyBot and it has some problems, but has not solved anything.

  I scoured several tech forums (including this one), but there are so many problems of type 0x000000D1, and so I am at a loss as to how I should proceed.

  I hope someone can help me understand this.

  Thanks in advance.
  I hope someone can help me with this.

  Hello ChrisDolan,

  If we can start in Mode safe mode with networking, then we have a problem with something loading at startup.

  The following article will explain boot minimum troubleshooting:

  How to configure Windows XP to start in a "clean boot" State

  Let us know if that helps.

  Best regards

  Matthew_Ha

• Windows 7 black screen with the cursor of the mouse in normal mode and safe

  Hi all
  I hope someone can help.
  Laptop downloaded updates and after the restart will only go to a black screen with the mobile mouse cursor.
  This occurs in safe mode, normal mode.
  I tried all variations of safe mode and still the same thing happens.
  Last known configuration does not solve. (i.e. no restoration or image to enter)
  Using the vista win7 dvd upgrade or a linux dvd and screen appears as you expect his obvious system is very good.
  I tried the options on ctrl alt del, ctrl shift esc etc etc, but I cannot go into Control Panel, or a any part of the win7 GUI.
  Best I can do is access via the command-line... any thoughts on how to fix?

  Hello

  Welcome to Microsoft Windows 7 answers Forum!

  You can try the following steps and check whether the problem is resolved.

  You can disconnect all external devices except the keyboard and mouse and check if you are able to boot to the desktop and check.

  I also recommend what to do the Startup Repair. Follow these steps:

  To perform a Startup Repair follow these steps:

  1. Insert the DVD of Windows 7 and restart the computer.

  2. when we are asked to press a key to boot from the DVD, please press enter or the SPACEBAR.

  3. choose your language settings, and then click Next.

  4. click on repair your computer.

  5. Select the operating system you want to repair, and then click Next.

  6. in the System Recovery Options menu, click Startup Repair. Startup Repair can invite you to make choices as it tries to solve the problem, and if necessary, it may restart your computer, because it makes the repairs.

  Access the link below for more information on the Startup Repair:

  http://windowshelp.Microsoft.com/Windows/en-us/help/5c59f8c1-b0d1-4F1A-AF55-74f3922f3f351033.mspx

  See also:

  http://social.answers.Microsoft.com/forums/en-us/w7install/thread/ab43493b-247C-427e-BA21-4950eea279ac

  http://social.answers.microsoft.com/Forums/en-US/vistawu/thread/24b44a01-872e-4d87-867f-ed01a3579031/ for the black screen problem

  Thank you, and in what concerns:

  Suresh Kumar-Microsoft Support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Can not get the display in normal mode = safe mode only. __

  System Restore does not work.  I got the no display problem resolved earlier and had cover down on laptop set to "do nothing".  I closed it and reopen, I was unable to get a display in normal mode.  I get the appropriate two sounds to start, but then nothing. Earlier, I used the system restore and I got a message saying it didn't restore my files, but it was up normally for 24 hours until what I closed the lid.

   

  Problems with system restore:

  http://Service1.Symantec.com/support/sharedtech.nsf/pfdocs/2005113009323013

  1. If you use Norton (Etc), disable it before using System Restore. info at the link above.

  2. try SR in safe mode:

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  3 Malware will stop at the system restore:

  If necessary, do all the workSafe Mode with network.

   

  To get intoSafe Mode with network, press F8 at the Power On / boot and use key arrow upward to get intoSafeMode with networking from the list of options, and then press ENTER.

  http://www.Malwarebytes.org/MBAM.php

  Malwarebytes is as its name suggests, a Malware Remover!

  Download the free Version from the link above.

  Download, install, upgrade and scan once a fortnight.

  See you soon.

  Mick Murphy - Microsoft partner

• off frequency message error when start the computer in normal mode

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Hey pamyres

  you say not what led to what happens

  You must give information here to get help

  try a restore of the system in safe mode before your problem

  http://www.windowsvistauserguide.com/system_restore.htm

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode option with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  Walter, the time zone traveller

• Error message when starting the computer in normal mode: btdna.exe

  I get this error during start-up:

  WSA startup failed or if you have the wrong version of the installed Winsock.

  I tried the command prompt, run as an administrator and reset but it not taken care of the problem.  Help, please!

  Hi Amy Shane,.

  Welcome to the Windows Vista answers Forum!

  You can check the following link and analysis online on your computer to verify if your computer is infected with a virus.

  http://OneCare.live.com/site/en-us/default.html

  Step 2: Manually remove BitTorrent from the PC

  1 open the Task Manager by pressing the Ctrl + Alt + Del or Ctrl + Shift + Esc key combination.

  2. go to the processtab.

  3. search btdna.exe and right-click on it.

  4. Select end process.

  5. click Yes when the warning sign is displayed.

  6. close Task Manager.

  7 Click Start then start search

  8. enter C:\Program Files\DNA\btdna.exe / UNINSTALL.

  9. use the search function for all other instances of btdna and also remove them.

  If you are prompted to restart the computer, then restart and reinstall the btdna.exe.

  Hope this information is useful.

  Jeremy K

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• start the computer in normal mode with settings in safe mode

  I restarted my computer from malwarebyes in safe mode and when he started he uses in normal safe mode settings. I tried to use the last good settings and she didn't date there. no old parameters. No idea how to get back to normal settings?

  You can either restore your system to a previous state.
  If this does not work, have to "msconfig" (run-> msconfig)
  In the new window, in the "general" tab, you can see three options like normal startup, diagnostic and selective upward.
  Select normal startup. then restart apply.and.
  That's all.

  Thank you.

• What is the problem with flight mode, by pretending to be on?

  We have several Yogas Thinkpad Windows 10 X 1, who (commentary on the https://forums.lenovo.com/t5/ThinkPad-X-Series-Laptops/X1-Carbon-and-Sierra-EM7345-problem-with-Mobi...) wireless connectivity problems, but this post is related to airplane mode.

  Our devices show the airplane as mode 'ON' in the 10 Windows Action Center, but the 'OFF' in the Windows 10 network and Internet settings. Wireless and mobile phones will continue to work, but the airplane mode button is always blue (see the attached screenshot).

  We have updated our wireless drivers and this problem still exists, what is happening here?

  AE_Support,

  Thank you for sharing your experience with different designs of airplane Mode in 10 Windows Action Center and 10 Windows network settings and Internet.

  This is a known limitation of Windows 10 threshold 2 v1511 and has been resolved in Windows 10 Redstone 1 released by Microsoft in August.

  Thank you

• Analysis of the error in normal mode string

  Hi all

  Suddenly, my analysis of the chain has stopped working and started giving me this error. The read string ends up being something like 2.86E - 4 or similar. When I run mode highlighted everything works fine and it interprets the number very well but when he's not in highlight mode it returns an error. Not sure why since it is just a number to convert. Any help? I have attached the error and the highlight mode version. Thank you!

  First guess: synchronization problem. Especially since you said it works in highlight mode. Specifically, when you run culminating point mode you expect probably not long enough before trying to read, and the loop will immediately detect any byte on serial port. This delay function there will not guarantee a delay of 1 second between writing and reading. There is no dependence on the data - a rookie mistake. Use an image sequence or time to late VI to have clusters of error wiring through establishing the data dependence.

• Stuck on a black screen on startup in normal mode.

  Vista Home Premium 32 bit SP2

  Every time I start up in normal mode I meet the dreaded black screen with cursor. I do ctrl alt delete to get the Manager of tasks and processes, I end explorer.exe and then start a new explorer.exe task that happens to me in my office in normal mode. However, the internet and most of the other programs do not work.

  I then restart and boot into safe mode, where internet and most everything else works as expected in safe mode. I tried startup repair and system restore. Running out of options... not very good with computers... spent the last week reading of many solutions on here and google.

  I hope someone can give me some advice on what to short to do a clean installation of vista. As I said, I can get it on in safemode and things work very well, it tries to start mode normal, that's the problem, and even once I get to the desktop in normal mode, nothing works well. I appreciate any help on this. Thank you!

  Hello

  You can access Mode safe? Repeatedly press F8 as you start? If yes you can try Control Panel - device
  Manager - graphics card - Double click on - driver tab - click on UPDATE driver - then right click
  on devices and UNINSTALL - REBOOT.

  Another method to try to get to the desktop (try in normal Windows Mode without failure)
  CTRL + ALT + DELETE and on the tab process EXPLORER.exe and COMPLETE the PROCESS on this subject - then
  on the Applications tab - lower right - new task - type in EXPLORER.exe. Safe mode is reached
  by tapping F8 as you start several times.

  First check this thread in case it is simple and if not to come back to this thread.

  http://social.answers.Microsoft.com/forums/en-us/vistaprograms/thread/50247d5e-0ae0-446c-A1bd-11287fd1478a

  Black screen problems are extremely difficult to repair and all patch is usually on a base hit or miss.
  That there is no information on a black screen as it is on a blue screen just adds to the
  Difficulty. Often using a restore point or Startup Repair will have no effect. You can try a
  Google to see the proposed repairs, whom some have worked however these cover a wide
  field efforts.

  Here's a video of one of them.

  http://www.Google.com/search?hl=en&q=black+screen+of+death+Vista&btnG=search&AQ=f&OQ=&AQI=G1

  Here's another fix
  http://blogs.PCMag.com/SecurityWatch/2008/12/the_mysterious_black_screen_of.php

  You have a Vista disk? You can try restoring the system to it. If you don't have the disks your
  system manufacturer will sell them at low prices. Or try in safe mode if you can get there.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  You can create a recovery disc or use someone even version (making the system restore it)
  must be bootable).

  How to create a Vista recovery disk
  http://www.Vistax64.com/tutorials/141820-create-recovery-disc.html

  ------------------------------------------------

  These require the correct Vista discs since you can not start safe mode.

  Try the Startup Repair tool-

  This tells you how to access the System Recovery Options and/or with a Vista disk
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  Try recovery options Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  -----------------------------------------------

  Here are a few Google searches where many have found different solutions:

  Vista black screen - check that a 1st
  http://www.Google.com/search?hl=en&source=HP&q=Vista+black+screen&AQ=f&OQ=&AQI=G10

  Vista black screen Solution
  http://www.Google.com/search?hl=en&q=Vista+black+screen+solution&AQ=f&OQ=&AQI

  Vista black screen Fix
  http://www.Google.com/search?hl=en&q=Vista+black+screen+fix&AQ=f&OQ=&AQI

  -----------------------------------------------

  If necessary and you can access all ordinary Windows.

  You can try an In-Place Upgrade (hopefully save programs and data) or a repair installation
  (if all goes well, the data records and need to reinstall programs). Be sure to do a good backup or three.

  You can use another DVD that aren't copy protected but you you need to own
  Product key.

  On-site upgrade
  http://vistasupport.MVPs.org/repair_a_vista_installation_using_the_upgrade_option_of_the_vista_dvd.htm

  If nothing works, you can make a repair facility that must save the data but you will need to
  Reinstall the programs. This also requires correct Vista disks especially for OEM versions. You will be
  need to know your product Code.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-happened-to-the-recovery-console

  How to perform a repair for Vista Installation
  http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

  ---------------------------------------------------------------------------

  Another method that works sometimes: at the command prompt, type of Vista startup disk:
  (a line type or copy and paste one line at a time and hit enter - enter a bracket)
  or "BOLD")

  c:

  cd\

  CD c:\Windows\System32\winevt (there is a space between cd and C :)

  Ren LogsOLD Logs (there are spaces between ren and newspapers and Logsold)

  RESTART Windows

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Problem with VI in Normal Mode, but not in execution to highlight

  Hi all

  This is my first post in this forum and I hope you can help me. I'm sorry for my bad English, English is not my main language.

  Now to my problem. I did a CNC with Labview machine, the machine has been built with a Lego Mindstorms NXT.

  The VI should read the lines in a text file, which a good movement for engines (G-Code). Mindsotrms LEGO NXT is connected via USB to the PC and the computer races VI target Mode. The VI is made in the 2011 Version of Labview with the Addon of NXT from Lego.

  Now the VI is finished, but he's going to correct work only in the Mode of execution to highlight (but he engines are not sync and his extremely slow). When I try to run the VI in normal mode, the engine for the port B does not work.

  Please can you help me.

  In the attachment, there is the VI (and an example of the G-Code (Code G example of Quadrat) file.

  Thank you very mutch.

  Kind regards

  Alex

  Your control loops seem to run (using all the CPU on the NXT loading) independent and probably cause famine across the loop.

  

  Add a delay here to minimize the problem.

  Not sure if it does help.

  BR,

  / Roger

• The problem occurs when I try to fullscreen ch. & c ++ in xp mode. It displays full screen ms - dos 16-bit error

  Original title: 16 bit mode fullscreen eror

  I use virtual xp on 64 bit ultimate windows 7. now the problem is occure when trying fullscreen c & c ++ in xp mode. It displays 16 bit ms - dos fullscreen eror

  Hello

  Because the problem is XP mode I recommend you post this question in Windows 7 IT Pro Forums.
  http://social.technet.Microsoft.com/forums/en-us/w7itprovirt/threads

• Do pop ups: update of Kaspersky Anti-virus and Unspecified changes to CONFIG SYS may have caused the problem after an unexpected shutdown and attempt to restore the system.

  Original title: unable to system restore

  After the unexpected stop down and try the system restore.  I got up a window pops that says update my KASPERSKY anti-virus program, I do not have KASPERSKY.    Another said unspecified changes "caudate root found" SYS CONFIG window may have caused the problem.   Any ideas?  I have Vista and Trend Micro Internet security

  Hi JevenStulie,

  1. are you able to boot into normal mode after receiving these error messages?

  You can try these steps and see if it helps.

  Step 1:

  You can check if the problem occurs in safe mode with network.

  Start your computer in safe mode

  Startup options (including safe mode)

  Step 2:

  If you do not experience the problem in safe mode with network, then you can read the following article to download the Microsoft Safety Scanner and analysis complete on your computer.

  Microsoft safety scanner

  Note: When you perform the analysis, there are chances of losing the data that you can take a backup of important data before performing analysis.

  Hope this information is useful.

• Error message "the service user profile Service has no logon. Unable to load the user profile"How can we get in the laptpop to solve the problem? /

  We get the error message "the service user profile Service does not logon, user profile cannot be loaded."  Prevents us from entering the computer laptop-so how to solve this problem?  Help?

  Hi LisaPie,

  Step 1: You can run the fixit available in the article below

  Error message when you log a computer Windows Vista-based or Windows 7 by using a temporary profile: "the user profile Service has no logon. Unable to load the user profile.
  http://support.Microsoft.com/kb/947215

  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  How to back up and restore the registry in Windows
  http://support.Microsoft.com/kb/322756/

  If you cannot start the computer in normal mode, try the steps in safe mode with networking

  Step 2: Start the computer in safe mode with network. To do this, follow the steps below:

  Access the menu advanced startup options by turning on your computer and pressing the button F8 before Windows starts. Advanced startup options menu select SafeMode with networking

  http://Windows.Microsoft.com/en-us/Windows-Vista/advanced-startup-options-including-safe-mode

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.