The QOS configuration

Similar Questions

• Question on 'sh queueing int' after the application of QoS configuration on 6500 line card

  I apply the following QoS configuration to a line card of 10 GB with 1P7Q8T queue structure. Basically, I'll put up the 2 for better queue to 60% and the priority queue for telepresence and singing at 30%, queue 1 to 5% and the rest queues 1%.

  int t1/1

  WRR-queue queue-limit 5 60 1 1 1 1 1

  bandwidth WRR-queue 5 60 1 1 1 1 1

  priority queue queue limit 30

  WRR-queue random - detect 1

  WRR-queue random - detect 2

  WRR-queue random - detect 3

  WRR-queue random - detect 4

  WRR-queue 5 random detection

  WRR-tail 6 random detection

  WRR-queue random - detect 7

  WRR-queue random detection threshold max 1 100 100 100 100 100 100 100 100

  WRR-queue random - detect min-threshold 1 80 100 100 100 100 100 100 100

  WRR-queue random detection threshold max 2 100 100 100 100 100 100 100 100

  WRR-queue random - detect min-threshold 2 80 100 100 100 100 100 100 100

  WRR-queue random detection threshold max 3 100 100 100 100 100 100 100 100

  WRR-queue random detection threshold min 3 80 100 100 100 100 100 100 100

  WRR-queue random detection threshold max 4 100 100 100 100 100 100 100 100

  WRR-queue random - detect min-threshold 4 80 100 100 100 100 100 100 100

  WRR-queue random detection threshold max 5 100 100 100 100 100 100 100 100

  WRR-queue random detection threshold 5 80 100 100 100 100 100 100 100 min

  WRR-queue random detection threshold max 6 100 100 100 100 100 100 100 100

  WRR-queue random detection threshold 6 80 100 100 100 100 100 100 100 min

  WRR-queue random detection threshold max 7 100 100 100 100 100 100 100 100

  WRR-queue random detection threshold 7 80 100 100 100 100 100 100 100 min

  WRR-queue cos-map 1 1 1

  WRR-queue cos-map 2 1 0

  WRR-queue cos-map 3 1 2

  WRR-queue cos-map 4 1 3

  WRR-queue cos-map 5 1 6

  WRR-queue cos-map 6 1 7

  queue priority cos-map 1 4 5

  MLS qos trust dscp

  When I do a ' see the race int t1/1 ' I don't understand a few things. "  Here is the "show run":

  interface TenGigabitEthernet1/1
  no ip address
  Shutdown
  bandwidth WRR-queue 5 60 1 1 1 1 1
  priority queue queue limit 30
  WRR-queue queue-limit 5 60 1 1 1 1 1
  WRR-queue random - detect min-threshold 1 80 100 100 100 100 100 100 100
  WRR-queue random - detect min-threshold 2 80 100 100 100 100 100 100 100
  WRR-queue random detection threshold min 3 80 100 100 100 100 100 100 100
  WRR-queue random - detect min-threshold 4 80 100 100 100 100 100 100 100
  WRR-queue random detection threshold 5 80 100 100 100 100 100 100 100 min
  WRR-queue random detection threshold 6 80 100 100 100 100 100 100 100 min
  WRR-queue random detection threshold 7 80 100 100 100 100 100 100 100 min
  WRR-queue random detection threshold max 1 100 100 100 100 100 100 100 100
  WRR-queue random detection threshold max 2 100 100 100 100 100 100 100 100
  WRR-queue random - detect 4
  WRR-queue 5 random detection
  WRR-tail 6 random detection
  WRR-queue random - detect 7
  WRR-queue cos-map 1 1 1
  WRR-queue cos-map 2 1 0
  WRR-queue cos-map 3 1 2
  WRR-queue cos-map 4 1 3
  WRR-queue cos-map 5 1 6
  WRR-queue cos-map 6 1 7
  queue priority cos-map 1 4 5
  MLS qos trust dscp
  end

  Issues related to the:

  1. why this show only two 'max-threshold', only for lines 1 & 2 - not for the other queues as is done for 'min-threshold '.

  2. Why does show "wrr-queue random - detect" for 4,5,6,7 queues and not 1,2,3 queues?

  It's the same thing, the default queues of 4-7 persons with reduced mobility.

  DAVID disabled queues: 4 5 6 7

  So when we allow them, they are added to the running configuration.

  Thank you

  The f

• What priority should I put in the QOS to work with IP voice service

  I have a new router Cisco RV180W and don't know which priority should I put in the high, medium, low possibility of QOS

  in order to work properly with the Ip voice device.

  The default values are 61, 31 y 10 but in a net with 12 PCs

  I think that this configuration 61 voice Ip and only 31 to the rest of the net

  is a value that is too low. This is definition 2 VLANs.

  How I can well criteria to configure these values of priorities?

  In the previous (a WR210 of Cisco router), the only thing that was

  set up which was the Ip voice connected in Lan 2 Port number with a high priority.

  I'm stuck with this matter and it should resolve quickly

  Thank you very much

  Daniel Di Matteo

  Hi Daniel, the claim of LAN should not affect the performance of the internet. All that is on the local interconnection, make queries on the local network will not use an internet connection. So as long as your servers/computers/cameras, etc. are using Cat6 cable and are all active GigE products, it will not be a large part of the review.

  But for your connection internet, you may be correct. 4/1 connection is not much.

  I need you to understand however, the WAN QoS for download speed only. Is not for download speed.

  You can make the profile works in 2 ways. You can keep the amount of download speed to a device or you can ensure that a device does not take more than he should.

  To set up a WAN profile correctly-

  QoS-> WAN QoS profiles

  Choose the maximum flow

  Specify your bandwidth

  Save

  Back to WAN QoS profiles, at the bottom there is a WAN QoS profile table, click Add. In the drop-down list, select the priority. Set the minimum and maximum bandwidth, and then click Save.

  Then you have to bound the profiles for the traffic selector. Go to QoS-> binding profile

  There is a service drop down choose which desired protocol

  Then choose the QOS profile you had a precedent set

  The last part, choose the IP address you want to assign.

  You can do this individually or in sequence. If you choose to be forbidden to use a device too download so that the beginning and the IP is the same. Conversely, if you have a range of devices, you can use their IP ranges if they are consecutive.

  Apply the profile, restart the router.

  I hope that I wrote this clearly for you.

  -Tom
  Please mark replied messages useful

• Cisco 6500's inside the VSS Configuration. Port ID's channel

  Hello

  I have a pair of 6500's Setup with VSS and there is currently only one link between then. However, one end of the link is Po10 and the other end is on Po25.  If I move the Po10 Po25, things will break? It seems to work fine now. I am about to add a second link and I am concerned about the current configuration.  It makes more sense for me to have the two ends of the same binding on the same port channel ID.  I have seen documentation that States otherwise however.

  Interface Port-channel10

  No switchport

  no ip address

  pass the virtual link 1

  MLS qos trust cos

  no consistency mls qos channel

  !

  Interface Port-channel25

  No switchport

  no ip address

  pass the virtual link 2

  MLS qos trust cos

  no consistency mls qos channel

  DTC_6509s_VSS #sh run int Te1/5/4

  Building configuration...

  Current configuration: 116 bytes

  !

  interface TenGigabitEthernet1/5/4

  No switchport

  no ip address

  MLS qos trust cos

  channel-group 10 mode on

  end

  DTC_6509s_VSS #sh run int Te2/5/4

  Building configuration...

  Current configuration: 116 bytes

  !

  interface TenGigabitEthernet2/5/4

  No switchport

  no ip address

  MLS qos trust cos

  channel-group 25 mode on

  end

  DTC_6509s_VSS #.

  DTC_6509s_VSS #sh vslp lmp sum

  Example #1:

  Summary of the LMP

  Information about the link: configured: operational 1: 1

  Peer Peer Peer Peer timers running

  Interface Interface state flag MAC indicator switch (time remaining)

  --------------------------------------------------------------------------------

  4/5/TE1 VSFP VSFP operational 0026.0a26.84c0 2 Te2/5/4 T4 (24ms)

  T5 (s 59.95)

  DTC_6509s_VSS #sh switch port-channel virtual link

  Flags: - Low P - D bundled in port-channel

  I have - autonomous s - suspended

  H Eve (LACP only)

  R - Layer 3 S - Layer2

  U - N running - is not in service, no aggregation

  f cannot allocate an aggregator

  M not in use, no aggregation due to minimum links has not met

  m don't use, port do not associate due to not meeting minimum links

  u - unfit to tied selling

  d default port

  w waiting to be aggregated

  Protocol for the Port-Channel port group

  ------+-------------+-----------+-------------------

  10 Po10 (RU) - Te1/5/4 (P)

  25 Po25 (RU) - Te2/5/4 (P)

  Hello

  It doesn't make a difference if you do both sides with the same channel id or not. The ID of the port channel is a logical interface that does not impact on the etherchannel between them at all. So, you can leave one side Po10 and other like Po25 without problem. Just make sure you have at least one member of the Portchannel Active physical interfaces for not losing your connection to VSS.

  Kind regards

  Mohamed

• Mac Air 1.3 Ghz i5, 4 GB ram end of 2013 everyone upgraded to El Capitan with the same configuration?

  worried about the going 10.10.5 Yosemite to El Capitan. Especially with only 4 GB of ram. Have 256 GB SSD HARD drive

  would appreciate an answer from people already have the upgrade.problems with the same configuration? slower?

  FWIW, the El Capitan applications are no different from Yosemite. In fact, it is easier on resources in some areas. The main thing you need to worry is to make sure the software and equipment to use is compatible. Make sure you have a good backup in case you change your mind and want to downgrade.

• Cannot move preview pane upward or downward in the classic configuration

  Cannot move suddenly preview pane upward or downward in the classic configuration. Currently stuck at the bottom. Have to double-click to display a message... OS 10.11.3 retina IMac tried restarts. several attempts of keyboard and mouse.

  Don,

  Keep trying... I found that simply getting a good lens.

  You can also try this diet between Classic and Classic 'no '.

  

• I don't have a navigation bar and firefox does not open in safe mode to return to the default configuration. Does not work reinstall. Any help please.

  I have no navigation bar since I closed it to have more space on the screen. It will not re - open. Firefox does not open in safe mode, but immediately opens in normal mode with the new configuration incorrect, so I can't reset to default configuration. I deleted Firefox and re-installed and it always opens with the same faulty configuration. Why doesn't Firefox give me the safe mode dialog box, why can I not re - open the navigation bar, and how I can do those two things, please? Firefox is currently unusable for me without a navigation bar with no access to the default settings in safe mode. I can't search the extensions that I use since I have no navigation bar to go to tools, modules, Extensions.

  This has happened

  Each time Firefox opened

  I closed the navigation bar to make more space on the screen and I could not re - open.

  User Agent

  Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 6.1; Trident/4.0; GTB6.4; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729 .NET CLR 3.0.30729; Media Center PC 6.0)

  Press the Alt key to display the Menu bar, then open view > toolbars and select menu bar and the bar of Navigation, so that they have a check mark.

• Every few minutes, the message "the network seems to be down. Is the network configured correctly? »

  When you play Pandora, every few minutes, the message "the network seems to be down. Is the network configured correctly? "is displayed. I click OK and Pandora continues. Network connection diagnostic report no problem. I have the BDP-S390 and a cable network.

  Hello Thomas,.

  Also, try using a different Ethernet cable or try to connect the player to another router's Ethernet port. He may be a problem with the Ethernet cable taking Ethernet to the router/player.

  Make sure that the Internet speed is 2.5 Mbps for SD videos streaming and 10 Mbps for streaming HD videos.

  If my post answered your question, please mark it as an "accepted Solution".

• ProDesk 600 G1 BIOS configuration of the TPM secure through the BIOS Configuration utility

  We have a range of devices, computers HP desktop and laptops in our environment.  Devices are all running Windows 7 64 bit and should have Bitlocker enabled, but we found that some were not encrypted.  So I am trying to set up a remote BIOS and Bitlocker config activate software that we can get out via SCCM and then embed in a task sequence image for new machines.

  I use the Bios HP Configuration utility to check a BIOS password is set and then activate the TPM chip.  I took a BIOS config output of each of our models and created a settings file that has all of the TPM associated parameters of all models.

  At the moment I run Setup BIOS utility manually for testing.  On all models I tried that works very well, except for the 600 ProDesk G1 SFF.

  When I run the utility on the ProDesk 600 G1 MFS, it says that I have managed to update the settings, and when I check the BIOS, the TPM secure has been unhidden and the TPM Management was given to the operating system (two settings I change), but the TPM itself remains hidden.

  It's the release of the BIOS configuration utility (it uses the 2.60.13.1 version, which uses plaintext passwords.  I also tried with the 3.0.13.1 later version that uses password files - same result)

  C:\ > BiosConfigUtility64.exe /cspwd: "password" set: "TPM_Config.REPSET"
  
  < BIOSCONFIG Version = "2.60.13.1" Computername = 'HP600G1' Date = "24/07/2014" Time = "13:01:37 ' UTC '1' = >"
  
  < SETTING changeStatus = "pass" name = "Embedded Security Device" reason = "' returnCode '0' = >"
  
          < OLDVALUE > <! [CDATA [hidden device]] > < / OLDVALUE >
  
          < NEWVALUE > <! [CDATA [device]] > < / NEWVALUE >
  
  < / SETTING >
  
  < SETTING changeStatus = "pass" name = "Enable security on the next boot" reason = "' returnCode '0' = >"
  
          < OLDVALUE > <! [CDATA [disable]] > < / OLDVALUE >
  
          < NEWVALUE > <! [CDATA [enable]] > < / NEWVALUE >
  
  < / SETTING >
  
  < SETTING changeStatus = "pass" name = "The BONES of on-board safety management" reason = "' returnCode '0' = >"
  
          < OLDVALUE > <! [CDATA [disable]] > < / OLDVALUE >
  
          < NEWVALUE > <! [CDATA [enable]] > < / NEWVALUE >
  
  < / SETTING >
  
  < SUCCESS msg = "Successfully set BIOS config." / >
  
  < information msg = 'BCU return the value' real '0' = translated = '0' / >
  
  < / BIOSCONFIG >
  
  C:\ >

  And after a reboot (where it should activate the TPM), BIOS shows as disabled built-in safety device (see attachment for the image).

  I have tried everything I can think of to get this to activate, including:

  • Different versions of the BIOS configuration utility
  
  
  • Remove the password from the BIOS and the application in the same order as the parameters
  
  
  • Different passwords
  
  
  • Reboot and allowing the machine to start completely to Windows before checking if the setting took effect

  I also tried to add the utility and the commands for an SCCM package and it works directly and as part of a sequence of tasks to see if that makes a difference, but nothing I've done has activated the TPM module.

  I know that the TPM module works, as you can turn it on manually and then Bitlocker can be applied to the machine, but with thousands of devices in our environment, I need to get this job without the need for manual intervention.

  Has anyone else had this problem and found a solution?  Or has someone at - he managed to activate the TPM on the SFF of 600 ProDesk G1 using the BIOS Setup utility?  Any ideas / suggestions would be very appreciated!

  P.S. This thread was moved from the company PC - Compaq, Elite, Pro for HP PC Client management. -Hp moderator of the Forum

  This problem has now been resolved by HP.
  
  They provided a replacement motherboard for the test machine I was using that solved this problem. I don't know what kind of motherboard failure could prevent the activation via the script TMP chip but not prevent activation through the BIOS menu, but as a replacement solved the problem, then it must be a hardware failure.

• Accidentally selected 32-bit instead of 64-bit to the initial configuration

  I chose accidentally 32-bit instead of 64-bit to the initial configuration. The computer (Satellite L630) came with a disc. If I create a recovery disc it will allow me to select 64-bit or it will create just once for a 32-bit system? Is there another way that I can return to the initial configuration?

  What model of laptop you have (L630-xxx)?

  Create recovery DVDs and test. You should not wait for a response, just to test it.
  You can also try to start installation of recovery of HARD drive, just to see what will happen.

  http://APS2.toshiba-tro.de/KB0/HTD9102IR0000R01.htm

• Re: Is it possible to create the current configuration of the software recovery disk?

  I recently bought A350. Next to the standard software provided by Toshiba, I bought and installed other products such as Norton Internet Security, update all drivers, etc..
  Is it possible to create a recovery disc on my current setup of the software?

  I know the recovery disk, but it will only restore the original configuration of the software. I don't want to go through all the pain of installing other products and update all the drivers.

  I have been using other software like Acronis Disk recovery, but I don't know this recovery cd created by these third party software can be used.

  Everyone has known about this?

  Hello!

  Boyfriend sorry but it is not possible to create a recovery disc with the current configuration of your software. The Toshiba Recovery disk contains the factory settings and t, you can integrate additional software to the image.

  If you want a picture of your laptop with your special software, you need to use another program like Acronis image. So you can make an image of your HARD drive with all your settings and software.

  Good bye

• Satellite U300-13U - iTunes has detected a problem with the audio configuration

  Please can someone help me? I have a laptop U300-13U and that you have installed iTunes on it. However, when I open iTunes I get an error message saying 'iTunes has detected a problem with the audio configuration and may not play correctly' which is an understatement - it does not at all!

  I uninstalled, reinstalled iTunes and Quicktime, but in vain. I have searched and exhausted the iTunes support boards but have nowhere either. The sound is fine as I can read CDs with no problems at all. The only suggestion I can get is that there may be a problem with the audio device magnet is not Apple and vice versa.

  Does anyone have AN idea at all as to what might be going on here? I'm completely out of my depth, I'm just a simple girl who wants to play his music!

  Thank you so much.

  Hello

  I don t use iTunes so I m not an expert player but first of all, you must give us some important information:
  -What operating system do you use?
  -Are you using the factory settings (Toshiba Recovery disk) or your own version of Windows
  -Do you have the yellow exclamation marks in Device Manager?

  OK, iTunes says that there is an audio configuration problem so do you trying to update the audio driver? If this isn't the case, you should try it.
  See the Web from Toshiba site for an update and see what happens. Then validate your result:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  Welcome them

• The Switch configuration and Wi - fi router in the same network

  Hi team,

  I have here is the configuration currently as below in the image. To describe the same internet cable is connected to a Cisco switch, which is connected to the PC in LAN (wired). A switch output is connected to the entrance of the wireless router Netgear Nighthawk AC 1900 Smart model of WiFi router # R6900. Wireless devices (laptop) are connected by the router.

  Each device has internet access. However, I am unable to run software LAN or unable to share any file of devices connected to the switch to the connected wireless devices. I can't ping any device the device wireless wired.

  Can anyone suggest what are the settings that I should do or what are the steps I should follow that will make wireless and wired devices in the same network.

  PS Plus early I tried the internet connection to the wireless router and then out of the router to pass, which has solved this problem. But slowing down my internet speed in wired devices. So, is it possible to have all devices in the network even with the current configuration?

  

  Thanks in advance.

  Best,

  Hardik

  I made wi - fi router reset hardware and configured in Access Point mode, that solved my problem.

• Messed up the initial configuration of Win Vista on Satellite L40

  I can only think that I messed up when performing the initial installation of Vista Home Premium on my new Satellite L40.
  I finished to the high withComputer\Vista C:\Users/comet containing all my stuff AND - outside of Vista C: - a full mirror in Desktop/Chris...
  Can someone tell me if I can return to the initial configuration screen and how?

  I tried to back up the directories and then delete them and you try to restore a single directory, but the other reappears too!
  I'm obviously a complete dunce so please do not forget that and keep your simple instructions!

  If anyone can help then anyone know a number 0800 for Toshiba Technical Support?

  Thanks in advance.

  Hello

  What s your problem exactly? You can start the Vista?
  If so, what you want to change it or not?

  If you can not boot Vista and then take your Toshiba Recovery DVD and try to reinstall it again

• Programmatically change the Active Configuration results

  I use TestStand 2012 SP1.  I would like to be able to configure the Active Configuration to get results in the process template.  A station in market our sequential model would set sequential reports configuration as the current record while a station running that a batch model would fix the lot of the report as the configuration active.  In addition, if a station can be both, running the application can select the appropriate process template and he would then choose the appropriate reporting configuration.

  I have installation of configurations but need to know how to set the active configuration.  I don't want on a base by sequence, but rather at the level of the process template so that it is executed once and done.  This would allow developers to change their configuration, but still have the lot or creating sequential reports selected according to whether they are working on.

  Thank you.

  There are a few options here:

  1. Replace the ModelOptions plugin and change the setting for ModelPluginConfigurationToLoad to the appropriate configuration.
  
  
  2. Hardcode it in the callback in ModelSupport.seq.  This way if you've always wanted by automatic override features and call their own as they could.
  
  
  3. Hard-code this entry point for execution of Initialize just before the ModelOptions callback is called in ModelSupport.seq.  In this way the customer can always substitute and change it if they want.

  If it were me, I'd go with option 3 for your case.  You can use Parameters.ModelData.ModelType to determine which model they are running with.  Then, simply put Locals.ModelPluginConfigurationToLoad on the proper setup.

  Hope this helps,