The questions on my Tecra 9000

Similar Questions

• The modem driver and TECRA 9000

  Hello
  Sorry for my English but I'm french.

  I'm looking for the driver of the modem internal will tecra 9000 for bus XP on TOSHIBA site they have there.
  Thank you

  Hello

  If you mean that there is no driver for the France, you're right. Try using the driver for other countries. I think it should work too. Maybe someone from Toshiba, read this and you will find the driver in the coming days.

  Good luck!

• Question about the temperature of the processor on Tecra 9000

  Hello. I would like to know what are the current temperatures for Tecra 9000 1 GHz. When I run an intensive application processor like Prime95, the temperature rises to 59 C. Isn't too much? Yes and I also recently replaced old thermal compound with AC MX-1.

  Thanks for your replies.

  Hello

  Thus, 59 c are quite OK, that they are almost under the PDT of the CPU. If the temp would be more than 70 ° C or more then it would be critical but not to 59 C. The Pentium 3 M should typically generate a higher temperature if your CPU is, comparing to another cooler system. Could be also dependent on the applied paste you´ve cooler...

  Don't worry Don t, everythings OK. :)

  See you soon

• Tecra 9000 upgrade question!

  Hello my name is tom and I have a toshiba tecra 9000.
  My problem is that the original toshiba 20 GB hdd is vice
  and I want to buy a new toshiba HARD drive.
  My question is:
  Gigabyte how can I install it on my laptop?
  I want to buy a 40 GB, 60 or 80 GB HARD drive
  is one of this size HARD drive compatible with my toshiba tecra 9000?

  EDIT:
  I forgot:
  The laptop has:
  1000 MHZ
  512 MB of Ram
  standard 20 GB HARD drive
  WLAN to edge (default external PCMCIA netgear Wlancard)
  16 MB S3 Graphics card
  14.1 "display

  Thanks in advance for answers

  Thanks apco. Great info! :) You have to test it on your Tecra? I hope that you did not notice any problems here.

• Tecra 9000 - no display on the LCD screen when you turn on

  I recently got a Tecra 9000 for cheap on eBay. I am experienced with the construction and repair of computers, but not so with laptops.

  The problem with this laptop, it's that do not display on the LCD screen when you turn on. It was just black, no backlight, nothing. I took the laptop all share, found no obvious problem. I had to turn it on and the screen lights up a few times trying to figure out the problem. Would it be a bad connection? Or something else?

  After getting it to start work, I'll try to start to put it back together and it stopped working again. I haven't not been able to reduce it to know if it's a bad connection or a card problem.

  Someone at - it suggestions? This is a problem for others here?

  As you describe the issue, I think it is somehow a bad connection or a damaged cable, because it does not work once you have disassembled the screen.
  Maybe you need to check all the cables, leading motherboard to the LCD and take a close look, maybe for a few scratches or strong curvature.

• Cannot use the recovery CD after update BIOS on Tecra 9000.

  Failed to retrieve the system (Windows 2000) after update BIOS on Tecra 9000. Recovery CD says "it's a bad machine. Can I go back to old BIOS? Another solution?

  Hello

  Maybe chain can confirm, but I put t he seems the best idea to mix stuff designed for laptops Americans and Europeans models.

  Can you please confirm if the method described in the previous ad works?

• Tecra 9000 running W2k - driver for the Audio controller problem!

  Help, please!

  I have a laptop Toshiba Tecra 9000 and recently discovered that the sound was no longer working. I'm not sure exactly when he first stopped working, but believe it was with MS Windows 2000 Updates or when cleaning PC after spyware attacks. While they inspected the real device (Yamaha AC - XG Audio Device), it has each if useful ""! "with a ' Code 10 - device cannot start", in the "Device status" screen
  I removed the device and allowed windows to detect & install, without success, then downloaded and tried many devices and generic drivers, drivers and
  even later as suggested on a Web of Toshiba site, I find
  http://EU.computers.Toshiba-Europe.com namely;

  Driver date: 22/05/2001 Version: 5.12.1.2138

  I'm at a complete loss as to why it has stopped working and what to try next to try and solve the problem. Any
  help or advice would be greatly appreciated.

  Concerning
  K

  Hello

  It is possible only after the installation of the MS Updates that the audio driver is blocked by a load of your system and no sound can be heard.

  If you want you can try to install this driver:
  http://drivers.Soft32.com/driver/download-Yamaha_AC_XG_Generic_Drivers_for_YMF753_743_752-24609.html

  It is useful after installing SP2. I don't know if this will help in your case, but you can try it.

  Good bye

• Tecra 9000: Where to find the driver for XP sound card?

  Hello

  I had a chance Tecra 9000 and installed a new Win XP Home edition. Sounds like the sound card requires an additional driver. Toshiba homepage can't stand the T9000. Any hint where I can get this driver?

  Thanks, Antiman

  Surely, Toshiba supports XP audio driver for Tecra 9000 series.

  Go here:
  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp?service=EU#

  and choose Archive-> Archive Tecra-Tecra-Tecra 9000 > 9xxx series >

  Enjoy ;)

• Tecra 9000 - bad scratch on the screen

  I have a Tecra 9000, which has a bad scratch on the screen.
  Does anyone know if the mask LCD Toshiba (P000328760) meeting will fix the scratch and if it is difficult to adapt?

  As far as I know if the stripe is displayed directly, this mask will help any. This mask is just sort of plastic placed around the screen cover.

• Tecra 9000 - Download the software for new installation

  Hi there;

  I lost the disc for my Toshiba Tecra 9000 laptop.

  Exactly what software needs to be downloaded to the default configuration for one of these?

  Thank you very much

  Hello

  What 9000 model do you have?

  All the required drivers and utilities are available for download on the web, but if you mean you want to put the machine in its factory condition, you need the recovery disc that came with the machine.

  If you provide the machine part number I can let you know what software has been bundled with it.

  Kind regards

  Nick

• How to change minPCI WLan on Tecra 9000

  Hello

  I have a Toshiba Tecra 9000 with 11b wireless.
  I bought a minPCI 54g card, but I don't see where is the mini on the Tecra 9000 pci card,

  My question is how do I change the WiFi card mini pci please?

  Thank you all

  Hello

  I think that if you can't find the WLan slot at the bottom of the unit, then it must be hidden somewhere under the keyboard!

  The keyboard is usually fixed with two screws that are hidden under a thin plastic above the F1 - F12 buttons cover.
  If you remove the two screws, you should be able to loft the keyboard.

  But be careful; It s to connect to the motherboard with a flat cable

• Tecra 9000 - LED flashes and cannot start

  I recently got an old laptop Tecra 9000. Unfortunately, it doesn't have a HARD drive (it was taken and sacked by the former owner).

  I bought some hard drives that I thought should work in this machine, but all that seems to happen is that the power light blinks 7 times, pauses, then flashes once (and then repeat this.

  I guess it's an error code any.

  Readers, I've tried are a MK4025GAS and a MK4026GAX. The result is the same on both.

  Can we say what means this error, or even tell me the part number of a disk that is compatible with this machine?

  Thank you very much.

  Hi Guy

  One question; have you tried to power the laptop without inserting the HARD drive?
  Usually if the laptop is ok, it should be possible to boot the laptop. Of course the laptop will not load the Windows operating system because the HARD drive is missing but it should be able to start and the led must Flash not!

  But if it flashes, it means that the fault was detected on the motherboard and the LED lamp sends a blink code.
  Short blinking means 0 and 1 long flashing
  Error code starts with LSB (least significant bit)
  for example:
  0000 0001-> 1000 0000

  This code you need to turn it into hex and you will get the error code.
  But in my opinion, no one will give you an answer what it means.
  Each laptop clean error code series offer...

• Tecra 9000 reload Windows XP

  I'm trying to reload my Tecra 9000 with Windows XP sp2.

  The CD I have another OEM but I guess it's always the same and so I should be able to use this copy?

  Basically, all charges fine but displays 3 yellow question mark dots Device Manager... 1 is Modem PCI, 1 video controller, and the other is peripheral unknown.

  I downloaded the drivers for the identified devices, but what do I need for the unknown device?

  If anyone has any ideas then please give me a shout.

  See you soon,.
  Joe

  Hello Joe

  In my opinion, you should try to install it. In this case, you need to install all the drivers and Toshiba designed tool later. On this path, it is not easy to say what write you about, but maybe a little tip can help you.

  On the Toshiba site, there is link to http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/generic_content.jsp?service=EU&ID=TIC2 knowledge base. Please go there and under Searchtext use the unknown word. Perhaps the first document can help you. He asks how to identify an unknown device in Device Manager?

  Good luck!

• Issue when installing fresh Windows XP on Tecra 9000

  I have a Tecra 9000 running Linux.

  I would like to install windows XP but the Setup CD I charge readers and then crashes to windows is the loading screen. I have no recovery disks or driver for this computer as I bought it used. and I don't know why he struggled.

  The SN for the unit is Z1086914G ST900-0.
  I have read forums about similar problems and think it might be the chipset driver for the HARD disk.

  I can't find a driver for nowhere so I can't try this line of thinking.

  Anyone has any ideas.

  Hello

  As I remember the Tecra 9000 does not support RAID or SATA controller that would require RAID or SATA drivers, so I put t think that your problem is related to the missing driver

  Have you tried to install Win XP SP2 from container?
  Are you sure that the HARD drive is OK? I think you should check the HARD disk for some problems initially.

• Tecra 9000 - BIOS block 1 damaged

  I have a Tecra 9000 with a broken BIOS.

  I looked at upgrading the BIOS FAQ [1] and searched the forum (found [2]). However, I have no Windows installation and at least my Toshiba Tecra 9000 doesn't have a floppy drive, so I can't follow the procedure described here.

  You will find my update of the BIOS for the laptop with the serial number 32222375G: http://de.computers.toshiba-europe.com/innovation/jsp/supportMyProduct.do?service=DE&userAction=SMP_RESU LTS_PAGE & partNumber = PT900E-08YZG-GR & serialNumber = 32222375 G & USER_ACTION = Serial % 20num ber

  So, what should I do?

  BTW: I can't real poster on this forum. I can't post the exact BIOS error message because the forum software claims that I used profanity. The relevant part is contained in the subject line of the thread.

  [1] [http://eu.computers.toshiba-europe.com/innovation/faq.jsp?FID=TRO0000000b07 |] http://EU.computers.Toshiba-Europe.com/innovation/FAQ.jsp?FID=TRO0000000b07]
  [2] [http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=46581&tstart=0 | http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=46581&tstart=0]

  Hi uAyjYdKT,

  Download a version on diskette in the bios called "trad.
  -You can always start your machine?
  -You can install anything on hard drive?

  If both answers are Yes, follow these steps:
  -do a back on your hard drive installation (this can be done on another machine)
  -unzip / uncompress the bios disk do a hard drive
  -Insert the hard drive of your machine and run the bios update

  If the responses were not: see one servicepartner to have made