Similar Questions

• Why my image does not reach the edges of the printed page, but seems in good condition in pdf?

  Why my image does not reach the edges of the printed page, but seems in good condition in pdf?

  Most desktop printers cannot image all the way at the edge of the page.

• Problem with Printer Color LaserJet 2600n of printing. Thin strips Magenta on the printed Pages

  I have a Color LaserJet 2600n, on which I replaced both magenta and yellow cartridges a week ago. Both cartridges are genuine HP. The printer cleaned and calibrated.

  Today, the thin magenta strips about 3 "apart began to appear on my printed pages. Print pages, but there is a 'click' stable, audible about 2 seconds apart from from the inside of the printer. Even after a cleaning several times, the bands are less bright, but they are still there. They also appear on the printed test page and on the page of troubleshooting print quality. Is there something wrong with this new magenta cartridge? This problem has never happened before in the 6 years, I've owned this printer.

  Here a link to the document that addresses the issues of print quality for your printer model. It will give you the different troubleshooting steps to try to resolve the problem. One of the steps in the document will guide on inspecting the print cartridge and see if the replacement is in order. I hope this helps.

• How do I remove a single white line on the right side of the printed page

  Appears on all printed pages, regardless of the source.  Kaleidoscope, cleaning, installation of new print heads and the linefeed calibration solves the problem.  The printer is an Officejet Pro 8500 a Premium.  Thank you.  I'd hate to throw a 18 month old printer in the trash.

  When you say that the issue is on the right side you mean the right side (and along the way on paper) when printing in portriat mode?  If so the problem may be due to a spot on the MICR band.  It is a fragile and delicate, tape printed with hundreds of lines per inch that the printer uses to know where the print head on the entire page.  Cleaning the MICR band, as described in this post can help solve the problem.  Be sure to heed the warnings.

• HP Officejet 7310 all-in-one: on the printed page without is not the margin settings and are shredded

  During a few days ago only, printer started the show message paper jam when the printed page was all but probably 1/8 "already out.  Flicking the paper really brought the page on the rest of the way.

  I remove the paper two-sided accessory to find any paper, but there is no paper jam that I can see.

  Also, in the middle of printing, sometimes it makes a loud squeaking (I guess), but kept in printing and sends the page completely.

  Then I started to notice that the left margin could tilt inward I look towards the bottom of the page or it can be different from one Word page to another and a blur occurs in a word here and there.

  Finally, on the printing of Excel pages, I see a different left margin on what I consider every 2 lines.  This, of course, affect the right margin in the same Manor, and the vertical cell lines also vary according to the variation in the left margin.

  The HP software tells me there is no update for me to download.  However, I do know she never talked about everything.  I have not seen this specific problem listed.

  @Sunny-Gal Hello and welcome to the Forums of HP, I hope you enjoy your experience!

  I see that you are experiencing printing problems. I would like to help!

  I suggest to remove the cartridges and perform a power reset.  Unplug the power cord from the printer and the power outlet, then wait 60 seconds. After 60 seconds, plug back in the printer. Make sure that you connect the printer directly to a wall outlet. Make sure to bypass any surge protector or power bar.

  I recommend also to download and run the HP print and Scan doctor.

  Good luck and please let me know the results of your troubleshooting operations. Thanks for posting on the HP Forums!

• don't want no logo appears on the print page

  Hello
  
  I use the logo in the application that will appear in all pages.
  I have the key "impression" on this page.
  By clicking on the button print the same page opens for printing with logo on top.
  What is the way that the logo is not present on the page to print.
  
  I use this for printing.
  function PrintAndGo()
  {
  var win = window.open
  ("/ apex/f?") p = & APP_ID.:50: & SESSION. (": PRINT: NO.: YES");
  Win.History.Go (0);
  Win.Window.Print ();
  Win.Focus ();
  }
  
  
  Thank you

  var win=window.open("/apex/f?p=&APP_ID.:40:&SESSION.:PRINT:NO::::YES");
  

  Does switch to view printable version, using the page template Print Version, where the table cell containing the string substitution #LOGO # lack the * class attribute .t6ApplicationLogo. Probably the best approach in these circumstances is simply to remove the string #LOGO # the printable version model.

• The print page opens not when I try to print a Web page.

  I use Firefox for many months and so far I have had no problem printing a Web page. I was away for a week and discovered this problem yesterday when I tried to print a Web page. Maybe there was some changes during the week that I'm not aware of?

  This happens on all websites or is it on particular websites?

  Normally, a button to launch a page in the print format appears in a new window. Blocker integrated in Firefox allows popups generated by a user by clicking, but if you have additional security modules, maybe one of them is blocking those.

  Could test you mode without failure of Firefox? It is a standard diagnostic tool to disable some advanced features of Firefox and extensions. More info: questions to troubleshoot Firefox in Safe Mode.

  Does not work if Firefox: Hold down the SHIFT key when you start Firefox.

  If Firefox is running: You can restart Firefox in Mode safe mode using either:

  • button "3-bar" menu > "?" button > restart with disabled modules
  • Help menu > restart with disabled modules

  and OK reboot.

  Two scenarios: A small dialog box should appear. Click on 'Start mode safe' (not update).

  Any improvement?

• No printer available in the printer page

  Original title: printers

  No printer appears in the Printers window in VISTA

  Error message "The Application subsystem spooler" stopped workung due to an error

  Hi sampsnc,

  1 when was the last time it was working fine?

  2. When you receive the error message?

  3. What is the serial number and model of the printer?

  A print spooler is a service that temporarily stores the disk printing hard or in memory until the printer is ready to print.

  See the link below and run the fixit tool available to them and check if it works.

  Solve printer problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-printer-problems

   

  Also, make sure that the print spooler service is running on the computer.

  (a) open administrative tools by clicking the Start button, click Control Panel, clicking system and Maintenance, and then clicking Administrative Tools.

  (b) double click Services. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  (c) right click on the print spooler service, and then click Properties.

  (d) under the tab general , next to Startup type, make sure that Automatic is selected.

  (e) also make sure that the service is started

  I hope this helps!

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• The printer page size setting does not work in Photoshop 5.1 with printer Xerox

  I am trying to print a size over 8.5 x 11 and Photoshop will not change the size, even if the setting of the printer is now in the largest size.  Illustrator and other programs will print but this Photoshop fails.  This is a problem in 32 and 64 bit versions.  Help!

  I found the following on the Xerox site... hats off to T Robinson:

  Re: Photoshop CS6 on Win 7 x 64 only prints the format letter on Workcentre 7655

  20/03/2013 12:28

  We have a Xerox WorkCentre 7435 PCL6, and I had a similar problem. I found a workaround in Photoshop CS5, I will describe where it is useful to others. I just upgraded to Photoshop CS6 however, and workaround no longer works with it. Instead, I get an error message if I print a report of the story of Job. The message is partially cut off at the right margin of the page, but the part I read says: "done with error(016-799): print educatio... failure detected in decomposer.» (The selection button indicates the part of the message that is cut off. What follows it appears on the next line down. I downloaded all updates to CS6 to see if that would help, but it didn't.

  Here's the solution that worked for me on CS5:

  1) click on "Printer setup" in the print dialog box

  (2) on paper in the drop-down menu, select 'Advanced paper selection.

  (3) select the status bar where your tabloid (or legal) size of paper is loaded

  4) click the button at the right end of the "Paper size" field to display the paper size dialog box.

  5) click on the down arrow button at the right end of the field 'Of the Original Document size' and select 'Tabloïd' (or 'Moral') in the menu.

  6) click OK to close each of the open dialog boxes until you return to the print dialog box and print your document. Print preview should update to show you a preview which reflects the selected paper size. (This can take a few seconds to arrive).

  It worked for me in CS5. Unfortunately, as indicated above, it doesn't seem to work on the CS6. The only solution I can offer for CS6 is to save the file as a PDF and print from Acrobat. It works without problem, but there are a lot of trouble to go whenever I need to print something other than letter size.

  If someone finds a better solution to workaround in CS6, let me know.

• Change the order of the printed pages

  My Deskjet 2540 prints page 2 before page 1; can I change the order so that it prints page 1, page 2, page 3, etc and if so, HOW?

  Ah... I'm sorry.  This printer does not have a duplexer, if you can't do two sided.  You must do it manually print the odd pages first and then put them back in and print the even pages.  I'm sorry.

• Series of HP Photosmart C5100: only half of the print page

  Original page version:

  

  my printer of the page version:

  

  How can I solve this problem?

  Hey @OMGEngi,

  Welcome to the HP forums! I hope you enjoy your stay here.

  I see you have some problems with the all-in-one Photosmart C5100 printer do not print in the right place on the page. I can help with that.

  First of all, make sure that the printer is plugged directly into a wall outlet , not a surge protector. It is this document explains How to solve problems of choice with the printer. This document describes a slightly different issue from what you describe, but it provides the same troubleshooting steps.

  If after completing the document, you still experience this problem then the printer must be replaced. You can contact HP support by clicking here and filling out the form below.

  I hope this helps and I hope you have a great week!

  If this resolve that your problem then please let others know by clicking on accept as Solution below my post.

  If you want to let others know that you will appreciate my help then please click on thumbs to the top of the icon on my post.

• Stops at halfway through the printing page...

  My Officejet 6700 Premium printer stops printing half way through the page. How can I fix?

  Hi @springie,

  Welcome to the HP Forums!

  I understand that your printer HP Officejet 6700 Premium stops printing half way through the page. I'm happy to discuss this issue for you!

  A few questions for you:

  • What happens when the printer stops printing? You get an error message? A paper jam? A blank page?
  • What operating system do you use? Windows or Mac? What version? http://www.whatsmyos.com.
  • How is the printer connected? Wireless, Ethernet or USB?
  • You use genuine HP cartridges or refills?
  • None of your ink cartridges are low or empty?

  In the meantime, if you are using Windows, please try our HP print and Scan Doctorand let me know what happens!

  If this, or one of the posts on this thread, helped you to solve the problem, please click on accept as Solution on the message. To show you 'like', or that they are grateful for my post, please click the thumbs upwards below. If there is anything else I can do to help, please don't forget to let me know!

  I hope hear from you soon!

• Remove header and footer on the print page

  Hi, I need to have removed the header & footer when you print a page.

  How would I implement this.

  I need to print from the AOL 9.7 software and the printer is a HP Officejet J4580

  Thank you

  It is a function of your printer software.  You will need to find the settings in the software.

• HP DeskJet 2546B: Deskjet 2540 stops in the middle of the print page

  I was not able to connect my computer to my pc via wifi a colledge, so I connect my printer via the usb port on my pc (I use the white cable provided with the printer that connects to the back of it). Impression of normal word documents is very well, but I have been tring to print several pages of a pdf file and it stops a few lines of print. No error message, no warning sounds, just stops. The power light flashes too.

  The cord is still plugged, it says in my devices on my pc that is always connected, and I can see the print job in my what. I can delete from my without any problem and it will spit the rest of th page. If I leave without doing anything, he will spit the pages finally after one minute. It will always work in Quebec of the printer, but it won't do anything with it.

  And I can't seem to convert the content of the pdf in word format to work around the problem.

  What can I do to fix this?

  Hi @Roket107,

  Thanks for joining the Forums of HP Support for a solution to your printing problem.

  I understand that you are using a HP Deskjet 2540 all-in-One printer with a Windows 10 computer and when you try to print from a PDF file the print job stops printing without any error messages, but seem to print correctly from MS Word. I would like to help.

  I would start by checking the printer software installed by downloading and running the tool HP Print and Scan Doctor. This tool can diagnose and solve many problems of printing software and printer.

  It could also help to ensure that the updates of Windows are updated.

  If HP Printy and the Scan doctor does detect no problem with printing software, perhaps that the software used to view and print PDFs must be updated, or uninstalled, then reinstalled.

  Please let me know if that solves the problem, or if you need assistance.

  Indeed, if this help you to achieve a solution please click the 'accept as Solution' and the 'thumbs up' buttons down below in this message.

  Thank you!

• HP110-230 t: my HP Photosmart printer output goes beyond the printed page margins

  When I speak of a document for printing, the actual production of the printer is in very large font size, which overflows to the right margin of each page. I can't find a way to set the output to the printer.

  Are you

  Glad to hear we're making @Estuprogress. It seems that my suspicion was right, that the question must have something to do with the way in which the program communicates with the driver. SO let's back peddle a moment. I think I asked a couple of times, but as a reading during our conversation I don't see an answer to what program you print from when this happens. Even if it is present for a number of programs please list them. There may be something specific program that we can modify to allow it to work properly with the right driver.

  The PCL drivers are the basis of the printing language, so that they are just much more basic. The goal is to solve the problem and use the driver designed for your printer. Didn't you try to the other pilot for diagnostic purposes.