The SG300 1.3.5.58 firmware upgrade problem

Similar Questions

• The WAG54GS Firmware upgrade problem

  Hello

  I am trying to update my firmware using the files provided on the linksys site. I have entered my serial number of the router correctly and chose the model of the good version (v.1.1) and downloaded the firmware file. I have connected my router configuration page, selected upgrade firmware and selected the id of the file downloaded. He got about 10% in the upgrade, and then he said it's the wrong file for my router. I currently have Firmware Version: V1.00.12 installed and I try to install the firmware Ver.1.01.03.

  Please can someone help?

  Marc

  Hi again,

  I feel such a fool as I now installed firmware annexed. As already mentioned by Kate, I wasn't directing the update firmware specifically for the IMG file.

  Ah, well you live and learn

  Your timidly

  Marc

• The RV042 Firmware upgrade problem

  Hello

  I was responsible for upgrading the firmware on the router RV042 in more than 30 remote locations. The problem is that when I update the firmware the vpn tunnel or office does not reconnect and we lose communication with the router. What can I do to keep the vpn tunnel directly without having to travel to each site just to get the vpn tunnel to the top?

  Thanks for any help.

  Hello

  You should check if the option Keep Alive and the dead peer detection is enabled on both ends of the tunnel VNP. They help to plug the tunnel once it falls.

  I hope this helps

• The SG300 1.3.0.59 firmware bug

  Hi all, I am having trouble with this firmware in a SG300-28 switch. In fact the DHCP server, a new feature in this version of firmware, does not work properly. DHCP static public reservations do not work: customer ID and MAC address are not recognized properly, and the DHCP server assigns the first free IP address in the pool, rather than reserved.

  If Cisco engineers reading this, plese fix.

  The issue is well documented in this thread, and it is present in the 500 series too:

  https://supportforums.Cisco.com/message/3941468#3941468

  Any help is appreciated.

  Thanks, Andrea

  Hello Andrea, the command is available on the global config

  Configure the terminal

  The dhcp server IP

  If the command is not available, it is because you do not use 1.3.0.59 at least. I'm under 1.3.0.59 and 1.3.0.62 and two software images have the command available.

  -Tom
  Please mark replied messages useful

• Shutdown after the last firmware upgrade problems

  After the last firmware update, I have questions turn off my rocket. If I try to turn it off during audio playback, the screen goes all black and turns off, and when turned on, it passes again by updating of media. She does whenever I turn it off if I do not push the button "Play/Pause" first. It's very annoying - anyone else knows this or can help?

  Sansafix said that it will be fixed in the next firmware. So far, just press the Center button until you turn it off!

• CP1025NW firmware upgrade problem

  I'm trying to update the firmware on my CP1025NW printer. The version of the firmware on the printer is 20100510 and the version on the HP site is 20110826. I have downloaded and run the firmware update and it turns a little and then says that he "cannot find the appropriate firmware file". I tried the update through a USB connection to the printer and a Wi - Fi connection running. Both result in the same error.

  Any help would be appreciated.

  Not sure if you have found the solution, but the mine has been change the printer to use a TCP/IP port and the printers IP address.  Once you do this, the firmware should be updated, then you can change it to the WSD port if you wish.

• LaserJet M4345 MFP firmware upgrade failure using the HP Download Manager

  Hi all

  I have a LaserJet M4345 multifunction printer, and I tried to see if there is any updated firmware for the printer.
  When I try to access the web configuration interface, I see that the printer is running a firmware with 20070213 code 09.071.8

  I downloaded the software from the HP Download Manager to try to update the printer automatically with a simple procedure.

  The program finds the printer and said that she needed upgrade. He showed that the printer is model J7949E and current firmware V.33.14 while the update of the Firmware version has been V.33.21

  I leave the program to start the process of update, but as soon as I said to start the update immediately (do not), a new window will appear showing the status of update and it closed after less than a second, replaced by another saying that the firmware update was complete.

  Although I was skeptical about the process in so little time, I tried to check again the printer web configuration interface, but it showed that the firmware was always the same, I saw earlier (20070213 09.071.8). To try to detect the printer from the Manager software download HP found that the printer was still need upgrading (and asked me if I wanted to do now). Try once led to the same results.

  I tried to restart the printer, the program and the computer with no result.

  I'm running Windows 7 32 bit and the printer is connected to the router which I connect this pc wireless.

  If I can provide any other information, please let me know.

  Thanks in advance for any help you can provide.

  Piero

  Hey Unreal, the product that you have is a printer. These commercial products can be a little tricky. For the best chance of finding a solution, I would post in the forum for HP Business Support.

  You can find the Board Commercial LaserJet here:

  Business - LaserJet HP Support Forum

  Take care!

  Sean

• Sony headphones Smart MW1 Pro - the device does not display mp3 information to do the firmware upgrade 0.1.D.0.6

  I bought the Smart Sony headphones Pro because the Sony site where there is an official document indicates that it is 100% compatible with my Samsung Galaxy Nexus.

  Everything was fine, until the unit was asked to update to version 0.1.D.0.6.

  After the pair with the headset Smart Display tells me "No Info" instead of the album and the name of the mp3 information.

  According to the forums, I'm not the only one with the problem and also cannot go back to previous firmware was 0.1.C.0.3.

  My Samsung Galaxy Nexus had the OS: android 4.2.1 when I run right.

  Today the android Smartphone I upgraded to 4.2.2 and maybe thought now and nothing will fix the problem, the problem is definitely the gadget.

  We need an urgent solution to this problem.

  This problem has been resolved by the 0.1.E.1.4 firmware which was released yesterday, also improves the screen, enlarge the icons and the clock digits, also solves problems with the mating with the Vita!

  Thanks Sony Mobile!

• The Linksys BEFSR41 V2 Firmware upgrade help

  I can't open the MacBinary (.bin) files that I downloaded from linksys, in order to update my firmware. I used my utility to archive, Stuffit Expander Mac and BetterZip, and so far none of them opens the file. Anyone have the firmware upgrade in a different format or advice on how to solve my problem.

  Do not touch the file you downloaded. The only software that uses it is your browser.

  You must open the web interface of the router at http://192.168.1.1/ and then use the upgrade of the firmware here.

  I don't know if the demo user interface is always up to date, but if it is as you should find it on the help page. See here. Click Update Firmware. Then, press the Browse button and select the .bin file that you downloaded. Then press upgrade and the browser will download the file on the router.

• After restart of the firmware upgrade

  Hi, I need to update the firmware on my controllers PS6100 EqualLogic.

  I found the instructions on how to do it and everything seems straight forward to do so via the GUI.

  I noticed there is a necessary restart after the firmware has been applied. Does this mean I have to gracefully shutdown the virtual machines running on my SAN LUNS? My iSCSI connections will be closed/broken during the restart of the post firmware upgrade?

  Thank you, Oliver.

  Hello Oliver,.

  In the same area download notes firmware and release is another PDF, entitled ' iSCSI initiator and optimize your SAN environment for high availability operating system considerations ", which includes some key parameters that will allow your computers virtual and servers through the failover time.  It is important that not only the Firmware update, but in the case of an unexpected failure due to a failure of CM.

  More if you use VMware ESXi, there is a best practices PDF for that as well.  In addition to better manage the failover, these changes have shown to improve performance as well.

  The Tech report TR1091 is available here:

  http://en.community.Dell.com/TechCenter/Extras/m/white_papers/20434601/download

  Changes for Windows and the knots of ESXi virtual machines will require a reboot to take effect.

  What version of firmware you are at, and what version you are migrating towards?

  Other things I always propose updates is to ensure that both controllers are plugged in your switch and in the VLAN correct.  Since assets CM are failed over to the passive, support gets much advertising is unable to access the storage after firmware update.  Or ports of the day before were not in the VLAN correct, or individuals with disabilities, etc...

  It is for these reasons that personally I prefer to do the updates via the serial port CLI.   The process is more talkative, and if something should go wrong, you need the serial port of some sort.   Since the installation and tested in advance is a huge time saver.   Here, we use serial mux so that all array controllers are easily accessible.

  Kind regards

  Don

• Cisco of WRV 210 Firmware Upgrade at the end of life

  I'm new to Cisco and not very knowledgeable on the networks, but looking for updated firmware for Cisco/Linksys WRV210 router.  Current firmware is 1.1.16 and I think 2.0.1.5 is available but I am not able to find if.  The router is on the list of 'End of Life' Cisco and is not supported, it seems.  I would like to move to a new router if there is no suggestion.  It is used for small businesses at home and structurally with cat5e cable.  Works well on my PC but when I went to the Macbook pro, I often have to renew the DHCP lease for a connection to continue.  When I added a 8 Dynex gigabit ports switch to my stereo equipment ' head in ' to divide the Ethernet for the TV, receiver, Set Top box and Blu - Ray on Pandora streaming now stops after a few minutes of listening.  Message appears on television (unstable network connection) or (not connected to the Internet) then removes Pandora.  With Ethernet connection running Pandora on my Macbook pro is always very well and never stopped.  I'm autoconfiguration for 100 Mbit/s full duplex (which could be a problem) and the new gigabit 8-port switch not set manually I know.  Maybe not the router but a problem of negeotiation automatic network.  I want to upgrade to 1000 Mbps network best steam netflix, etc.  I'm not sure I even the configuration of the router WRV 210 correctly, but if I replace it, I'll use it in another application.  I thought that I would update the firmware on the router WRV 210 to see if it helps while working this problem.  I can't find the firmware, if someone could make a suggestion, I would it would be greatly appreciated.

  Scott,

  Navigating Cisco's Web site can be a little intimidating sometimes.  Here is a link to the firmware:

  http://www.cisco.com/cisco/software/release.html?mdfid=282414014&flowid=788&softwareid=282463177&release=2.0.1.5&relind=AVAILABLE&rellifecycle=&reltype=latest.

  You may need to be logged in order to reach this link.  If you do not have a Cisco user id, you can sign up for one and it will allow you to get more resources than when not connected.

  Mark Furlong

• How much time it take the firmware upgrade procedure?

  Hello

  I ReadyNas 204 and I'm away from the SIN it free and I wanted to install the 6.5.0 version of the firmware via the admin interface... I'm not sure how much time should I take, it is already underway for 40 minutes... is this normal?

  Sorry for the dummy question!

  Thank you

  Problem is solved. Sent someone back home to check and it seemed that the NAS could not obtain an IP address after you restart. Disconnect the RJ-45 and connected back solved the problem. NAS is back online, but would it be a bug in 6.5.0 or is it just with my camera? Nothing in the newspapers that I could see... just could not obtain an IP address...

  the NAS drive is configured with a static IPv4 address and IPv6 is disabled. If that helps.

• BDX4350KB Wifi adapter and firmware upgrade doesn't work do not

  It is a sequel to my earlier question about if the WLM-20U2 Wifi adapter will work in my blu - ray player.

  After buying the adapter I plugged it and a message 'not supported', if I tried to connect wireless it says there was no an adapter connected.

  So I assumed that this necessary upgrade, so I formatted a 1 Gb USB drive with the FAT file system, downloaded the file level (version 39 http://www.dl.toshiba.com/player/NA/GB/EN/BDX4350KB.html) and copied the file .bin on the USB.

  When I plugged into the player and said to check the disk for a file to update it tells me that "frontend file is not found"... There was only one file to download, and it wasn't in a folder so I guess I'm supposed to just copy that file on the USB drive.

  I checked the USB port with a memory stick with photos on and it works fine.

  How to get the upgrade to work in the hope that it will enable the wifi adapter to work?

  Thank you

  Have you checked the guide in PDF firmware update?
  [Update firmware BDX4350KB | http://fget.dl.toshiba.com/manual/install/10009/Installation_Instruction.pdf?fromPid=%2Fplayer%2FN A%2FGB%2FEN%2FBDX4350KB.html&f=Installation_Instru ction.pdf]

  _ * How to upgrade the F/W * _

  (1) update firmware requires the USB of size max.2GB. Please make sure you format the Flash DRIVE to FAT/FAT32 before you start the upgrade procedure.
  ? Create a new folder on the USB drive and name it UPG_ALL
  ? Unzip the firmware file and copy it in the folder UPG_ALL.

  2) turn on the BD? Drive and make sure that you can see the player's on-screen Menu.
  ? Insert the USB key containing the Firmware upgrade file in the USB of the Blu slot? ray player

  3) press the "SETUP" button on the remote control.

  ? Select keys on the remote control UP/DOWN
  ? Symptom
  ? Upgrade
  ? USB storage device

  4) press the OK button on the remote control depending on the USB storage device.
  ? Now the upgrade file is under research. Please wait massage will appear

• Extension stopped working after firmware upgrade WN2000RPTv3

  I updated my firmware to wn2000rptv3 - V1.0.1.4.

  Now, my range extender only goes to a page in the account registration.

  Nothing I try (mywifiext.net, http://www.routerlogin.netor .com) helped him.

  While I didn't create an account, I tried to anyway.

  After you have filled all fields, the next button stayed grayed.

  It didn't matter how many times I've tried, it's always the same.

  I tried with passwords symbol 12 and 15. No luck.

  Now, my extender is basically useless unless someone can tell me how to solve this problem.

  The Extender worked like a champ before the upgrade.

  Just goes to show that newer isn't always better.

  Any suggestion is appreciated.

  Thank you.

  Thanks for the reply DarrenM.

  I followed the instructions but it will not be upgraded. I tried several times.

  Finally, I rebooted the computer and retried all on and VOILA, it worked like a charm.

  I even braved upward and updated again and it took the update of firmware as a champion.

  Don't know what I did wrong on the first upgrade.

  Don't know what tomorrow will bring, but tonight, I'm a happy camper.

  Thank you very much!!!

  SM

• 200 d IOmega IX4 Firmware upgrade failure

  Hello

  I have an IX4 - 200 d which I inherited. Initially, it wouldn't boot and display only the symbols of USB stick/network after about 60 seconds.

  With some searching on Google, I created a boot disk USB with the firmware updated on this issue. All goes well until the Firmware upgrade begins. I go to the step of (what I assume is) the upgrade of the firmware and it gets 75%, hold for 5 seconds and then the machine stops.

  I tried to repeat the update of the firmware with all the drives present, with every other drive in the first slot and with all the disconnected drives. But it seems to behave in the same way.

  Is this a known issue? Or could it be a hardware failure?

  I'm pretty eager to find a solution - it takes a long time for me to accept defeat.

  The only other suggestion that suggested Dr. Google is to start linux and reformat the hard drive?

  Any help is appreciated.

  Kind regards

  Pete

  Hi André,.

  This case can be closed.

  After the above mentioned procedure eventually work, I didn't know that - ALL readers should be present and formatted during an attempt of USB firmware update / install.

  The link again on the forum - http://forum.nas-central.org/viewtopic.php?f=14&t=4401

  This seems to be the only solution.

  Kind regards

  Pete