the Z2 firmware error

Similar Questions

• Error on the UPS Firmware Dell Update utility

  Hello

  I got the error "No UPS connected or not able to make the connection" the inverter is connected by USB.  I have RS232 or USB enabled in the upgrade utility.

  I'm under UPS Local Node Manager, that's how I know that the UPS USB connection is good.

  Manager of local node said in respect of the power supply: Dell Rack/Tower UPS 2700W UPS RT LI LV 2700.  The device status for lack of UPS.

  The following information found here that I'm updating the firmware and then replace the battery followed by replacing the battery if the fault is not resolved.  I have re-sitting and replace the battery with a new battery.  The front panel of the inverter shows again the fault as well as the software after replacing the battery.  It seems that the update of the firmware is the only option for this error at this stage of troubleshooting.  However, the upgrade utility does not work.  Please help.

  Sometimes they have the management software will not allow the firmware update utility to try and work as follows:

  1. If the inverter has the NMC (Network Management Card) installed, then select the NMC in the utility of upgrade of the UPS Firmware and update the firmware of the UPS.
  2. Connect the ups to another system (server, desktop computer, laptop computer) that has neither ULNM nor would save installed. Load the utility to upgrade the Firmware of the UPS and the UPS firmware on the new system files. Launch the UPS Firmware Upgrade utility and update the firmware of the UPS. Reconnect the ups to the original system.
  3. Uninstall the ULNM and/or would save the system. Launch the UPS Firmware Upgrade utility and update the firmware of the UPS. Reinstall ULNM and/or save. Check the configuration settings.

• The program displays error 1 airport

  I have a network of 2 time Capsules from the airport and 2 Airport Express. One of the time Capsule is the main base of the network, the other edefinde ar as extension. Everything works perfectly since ages. Today, the main basis had the yellow light. I power market and everything happened after commissioning in normal operation. Later I started my program from the airport and here it shows me each device, but each device gets a sign, Red '1' in a button white. When I click it, I just get the detailed information of the device. Amazing that I don't get this message on the program from the airport to my iPad.

  I run on my MacBook Pro, 3 GHz Intel Core i7, OS X El Capitan 10.11.6 Beta (15G7b), on time as well as the AirPort Express Terminal Capsules 7.6.4 Version.

  No idea what this '1' means? I couldn't find any information in FAQ or support for the network in error messages.
  The network actually works, so I don't know if it's an error message or just any type of warning.
  Thank you, Roger Che.

  Yesterday, I received these insignia (white '1' in red).  He indicated that there are updates firmware for all my devices from the airport.

• HP compaq dc7600 new CPU arrives with firmware error

  I have the computer says in the title and it came with a pentium 4 cpu which is GHz. I have a p4 GHz cpu, which is the same socket and according to the website of hp, it is compatible.

  When I try to start the computer it comes up with an error message saying it needs a firmware update.

  I looked at the bios update but I don't really understand how it works.

  If someone could explain how to fix this error and or update the bios that would be great.

  Hello:

  You may need to install the latest firmware update.

  http://h20000.www2.HP.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en & cc = us & prodTypeId = 12454 & prodSeriesId = 472276 & swItem = PSG_I23753-109013 & prodNameId = 472278 & swEnvOID = 1093 & swLang = 13 & taskId = 135 & mode = 3

  Read the instructions on how to install it.  You need a bootable USB key to do.

  Read these instructions on how to make a bootable flash drive and then copy the contents of the flash file to him BACK after making the bootable disc.

  http://www.techpowerup.com/forums/showthread.php?t=47812

  Paul

• ReadyNAS 3200 > try to download the latest firmware - file 404

  Hi all

  The web site has RAIDiator - 4.2.29 as the latest firmware for my devices.

  However, the link provided, http://www.downloads.netgear.com/files/GDC/RNDU2000/RAIDiator-x86-4.2.29.zip , gives a 404 - File not found error.

  Does anyone have a solution?

  We pulled RAIDiator - x 86 4.2.29 and will soon release 4.2.30.

• R7000, problems with wireless connection after the last firmware update 1.0.6

  I recently updated to the latest firmware available for the R7000...

  The upgrade went well and my Wired PC all connected without any problem, but several of my wireless devices were unable to connect to the WiFi. I have my cell phone Wifi (Android phone) kept gives me an error of authentication, but was able to connect to the network comments... weird...

  I started firmware 1.0.4 and everything worked well again... it seems that the new firmware is buggy.

  The Firmware versions listed above are only for the first three issues, to save typing, but you get the version that I use...

  Nick

  Hello

  I would like to let you know, I've improved in 1.0.6 last night and everything worked. The difference is this time I had to reset my router to the factory settings using the reset hidden at the back button and hold the button for about 7-10 seconds. This resets the router to the factory settings. I then had to re-enter all my IP address reservations and the word block list, but all my wireless devices were able to connect. The last time I did the upgrade, I just restarted the router, and I had read that I had to do a factory reset to operate correctly.

  It would have been nice for Netgear arrive at a way to extract Information form my version last-place back... it would have saved me a lot of time...

  Good luck

• PXI 7330 download firmware error

  I connected a PXI 7330 Motion control card.  Then I tried to download the new firmware / make sure that the connection worked.  I followed the instructions on how to do it from the Start Guide it came with.  I opened measurement and automation.  Expanded devices and Interfaces, so NEITHER Motion devices.  Choose the 7330 motion controller.  Click the firmware tab.  Click update firmware.

  However, I got an error saying that the device needs to be reset.

  How can I put the reboot appliance?

  When I chose the 7330 motion controller under hardware OR movement, I noticed she had a red x on it.  That probably shouldn't be there, but I don't know how to get rid of it.

  It turns out that all I had to do was click the 'Reset Device' button in the status tab, located next to the firmware tab.

  I called the help line OR to get the answer.  I had the latest drivers of movement OR installed.

• WINDOWS cannot OPEN THE FILE D:\Sources\Install.wim REQUIERED. Make sure that all required files for installation aare available and restart the installation. Error code: 0x8007000D,.

  IM TRYING to re - INSTALL WINDOWS VISTA ON MY T-6321 to the front door, BUT WHEN I INSERT THE DISC, AND INSTALL, a MESSAGE APPEARS SAYING: WINDOWS cannot OPEN THE FILE D:\Sources\Install.wim REQUIERED. Make sure that all required files for installation aare available and restart the installation. Error code: 0x8007000D, SHOULD ALL BE ON THE DISCALREADY?

  Hi JRCLNSIN100,

   

  Welcome to Microsoft Answers Forums.

  We would like to get some more information from you to help solve your problem. You better, please answer the following questions.

  ·         What is the disk you use to reinstall?

  ·         Is this a recovery or reinstalling the disc you are using?

  ·         When exactly do you get this error message?

  ·         What is the edition of Windows Vista, you try to install?

  ·         How old is the drive that you are using?

  ·         How are you starting the installation process?

  After researching the error 0x8007000D code is essentially due to file corruption and a problem with the drive itself.

  First check if you have scratches or dust on the disc and clean the surface and try again.

  To check if the disk is wrong, you will need to copy the contents of the DVD to the hard drive and try to install using that.

  To perform a flat installation of Windows Vista, follow these steps.

  Note The hard disk must have at least 3 GB of free space on the disk for the Windows Vista installation files. The hard disk must have at least 15 GB of additional disk space to install Windows Vista. For more information about system requirements for Windows Vista, see the Microsoft Web site at the following address:

  http://www.Microsoft.com/Windows/products/windowsvista/editions/SystemRequirements.mspx

  1. Insert the Windows Vista installation disc.
  2. Start Windows Explorer.
  3. In Windows Explorer, click to select the drive for the Windows Vista installation disc.
  4. On the Edit menu, click select all.
  5. On the Edit menu, click copy.
  6. Click to select the hard disk you want to contain the flat installation files.
  7. On the file menu, point to new, click the folder, type Windows Vista Setupand then press ENTER.
  8. Double-click the Windows Vista Setup program, and then click Paste on the Edit menu.
  9. Double-click Setup.exe, and then follow the instructions that appear.

  See the link below for more information on flat installation.

  How to perform a flat installation of Windows Vista

  http://support.Microsoft.com/kb/928902

  This problem can also occur if the firmware of the DVD drive is defective or obsolete.

  If the step above does not resolve the question suggests that you install the latest drivers for the DVD player on the computer.

  For more information please visit the link below.

  Error message when you try to install Windows Vista by using the DVD drive on the computer: "Windows cannot install required files".

  http://support.Microsoft.com/kb/930984

  Hope this information is useful.

  Let me know if it worked.

  All the best!

  Thanks and greetings

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• HP Laserjet Pro400 M401dn: the 49 Service error

  Error 49 Service on screen touch printer. Will print no from a Microsoft Office document.

  Have followed the instructions (by HP support) to close printer, unplug the USB and disconnect the power supply to the power surge suppressor and then plug the electrical appliance into the wall socket. Then reconnect USB. All done, rebooted the printer and printed a document internal printer (report Configuration and Menu support) which printed fine.

  But printer will not print a document from Microsoft. Of the 49 Service error. Use Microsoft Office v.X student/teacher edition for Mac (2011).  It was most recently updated, 10 may 2016 with office update 14.6.4. I printed some documents after this update, but now this 49 daycare error appearing.

  Product number for this printer Laserjet Pro400 M401dn is: CF278A

  Any help would be appreciated.

  Steve945

  If you unplug the printer from the computer or network and turn on the fact come ready.  If so, then the print job that is still trying to print or a new print job is causing the error.  Delete all print jobs from any computer that uses the printer.  First upgrade the firmware using the easy firmware updating program.  Then try the same job and see if works.

• The HP printer error

  I have a jet laser pro M275 get 79 service error. TRN and always on the same message again. Changed ink crt printed now.

  Hello Gmom25,

  Welcome to the Forums of HP Support! I see that you run an error on your HP Laserjet Pro M275 "error 79Service".  Go ahead and try a cold reboot:

  (1) disconnect the power supply to the printer.
  (2) hold the symbol (*) & enter buttons simultaneously and switch the power on.
  (3) wait until you see "Permanent storage init" msg (I think that this is but not sure the exact msg) and then release both keys.

  If you still receive the error after the reset, have a look here: Solving of control panel Messages, according to table looks like this error may be related to the Firmware.

  In my view, there was an update sent 2013-11-06, which includes many improvements and fixes. Please select your current operating system in the drop-down list, click Next and under the Firmware section to try and install the update, if you are able to get out of the error state.

  If you are unable to get rid of the '79 Service error", I suggest to call our technical support at the 800-474-6836. If you do not live in the United States / Canada region, please click the link below to get help from your region number. http://www.HP.com/cgi-bin/hpsupport/index.pl

  Thank you

• the iDRAC6 firmware update failed during the process

  Hello

  One of my colleagues went to a customer who has a few problems with the upgrade of its most recent firmware iDRAC6.
  Case 1
  R710 - with firmware version 1.41-> 1.54 fails to 30%

  Case 2
  With the firmware 1.54-> 1.70 R710 - fails to 30%. Also I tried 1.54-> 1.80 fails also to 30%.

  In both cases we found no indicationin error log files. Download was fine, checksum is ok, only FW upgrade failed, but no details.
  It's a common mistake? What can we do to work around this error?

  Kind regards

  Stijn

  I finally after trying to update iDRAC 6 version 1.0.3.10 to 1.98.8 (last update of this post)

  The update (stuck) were held 30%.

  Solution is to download "firming.d6" * wait 5 minutes * before clicking on the button update to begin loading the new firmware.

  R610 server would not update unless the server has been turned off and then follow instructions above.

  If I clicked the button to update firmware soon after downloading the file, it would always fail at 30%.

• On 2350dn 900.57 firmware error

  I get a 900.57 firmware error code on my Dell 2350dn printer lately. I searched Dell support and found an update of the firmware Urgent that supposedly solves the error of 900.57, but this update was for a 2330dn and not 2350. There is no update of the firmware available for the 2350. The update of 2330 will work with my printer? This has been an annoying problem for about a month now.

  Thank you.

  Yes the 2330 drivers and firmware should work perfectly for the 2350dn printer. In addition, the error of 900.57 is specific to the driver you are using. I think it's a mistake PCL and the 900.43 is a PS driver error. Try changing the driver to the Open Dell print or just try to swap between PCL and PS Si firmware does not help.

• Unable to connect to the MKS: internal error

  After you add the hosts to vCenter, when I try to KIKILA the VMRC, I get the error: could not connect to the MKS: internal error

  First of all, this isn't the usual DNS resolution of Host IP addresses MKS error! This is something totally different.

  An unusual thing in the manifestation of this problem which is to turn it off (completely off, not a reboot) and then turn the virtual machine in question, the console will work for this virtual machine, but the console continues to malfunction for the other virtual machines on the same host until these virtual machines are vMotioned or completely powered by bicycle!

  Here's the workflow:

  1. I have to stand up a new ESXi (patched and firmwared to the latest updates)
  2. I build a Windows or Linux VM to serve DNS and/or be an AD domain controller
  3. I have install the VCSA (or Windows vCenter)
     1. I connect and test forward and reverse the resolution for all hosts in the Broadcast domain
  4. I add the ESXi host (and all other hosts) to vCenter
  5. I try to open a VMRC and get the MKS error!

  It is a minor problem, with the exception of the VCSA himself!

  Any ideas?

  I had the same exact symptoms as you. Fortunately, I was able to find this link:

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalID=2116542

  Looks like we have a need is power off and turn it back on, suspend and energy back or vMotion to another host to resolve. I guess it has to do with the generation of a new SSL certificate when joining a host to vCenter? I checked that at least the first two options work, so I hope that answers your question.

• Why always show that "there is a connection to the Apple store error."? It has been a month I am facing such a problem. How can I fix? Hope you have a solution to this...

  Why always show that "there is a connection to the Apple store error."? It has been a month I am facing such a problem. How can I fix? Hope you have a solution to this...

  I don't know if this is the problem, but it is something that must be correct establish a secure connection:

  Open Date and time preferences system, Date & time tab. Make sure that it is set to automatically set the time.

  Alternatively, make sure that your date/time is correctly set to the second.

  Another thing to try is to restart your modem and router.

• Impossible to install the Safari extensions; error message

  Impossible to install the Safari extensions; error message

  Hello

  Make sure that OS X and Safari are up-to-date.

  Open system preferences > App Store, then click on: check now

  Your profile says your Mac works v10.11.1. The v10.11.5 update is available. This is maybe the reason why you can not install the Safari extensions.