There is no command 'Switchport Voice Vlan"on SF300 - 24 p!

Similar Questions

• Need help to set up voice VLAN in SG300

  Hello

  I spent too much time on it now and need help. I'm trying to set up a voice switch VLAN on a SG300 - 28 p. I need to charge a phone Cisco 7965 connected to a port on SG300 - 28 p to use VLAN 100, and a workstation connected to the phone to use Cisco 7965 on VLAN 101 by SG300 - 28 p. In the common Cisco IOS switches, this task is configured as follows:

  interface gi25

  switchport mode access

  switchport access vlan 101

  switchport voice vlan 100

  Trying to achieve this scenario with a Cisco SG300 switch turns into a nightmare. You will have to deal with a Dynamic of VLAN voice Auto Voice VLAN mode. Then, you must have a configured trigger and activated Automatic Smartport . I tried to do this in CLI nothing helps. Cisco 7965 receives an IP address of the access VLAN on Gi15 interface, which is 101 VLAN. I need to receive an address IP of the VLAN 100.

  The current configuration under Gi15 interface is as follows:

  interface gigabitethernet15

  activate the storm control

  broadcast storm control level kbit/s 10

  Storm-control include multicast

  port security throw trap 60

  maximum port security by 10 points

  port security mode max-addresses

  spanning tree portfast

  LLDP-med disable

  switchport mode access

  switchport access vlan 101

  ! next order is internal

  macro auto smartport dynamic_type unknown $native_vlan 101 $voice_vlan 100

  Now, I don't know how the macro auto smartport dynamic_type unknown $native_vlan 101 $voice_vlan 100 command in the config, and I do not know how to remove it.

  When I try to enter the command macro auto smartport type ip_phone_desktop under Gi15 interface, I get the following error message:

  The $voice_vlan macro setting is not configurable by the user

  It seems that the auto attendant smartport macro ip_phone_desktop can not apply the setting $voice_vlan with a value of 100. In fact, I explicitly does not use this parameter to everything in the order of macro auto smartport type ip_phone_desktop ; However, the SG300 switch knows that the voice VLAN VLAN 100, and he's trying to use this VLAN ID as the value of the $voice_vlan parameter, the macro fails.
  

  I tried statically configure the voice VLAN on the switch SG300 using the command id of the vlan 100 voice , but I couldn't get the ip_phone_desktop macro to configure interface Gi15 correctly. Then, I removed the command id of the vlan 100 voice and obtained SG300 to learn his voice VLAN ID of UC560 connected to the SG300 through a trunk port based on the port configuration (connected to SG300) for the trunk of the next UC560:

  switchport trunk vlan 101 native

  switchport mode trunk

  switchport voice vlan 100

  Cisco-switch macro description

  This is the command switchport voice vlan 100 who announces to SG300 via CDP VLAN 100 is a voice VLAN. When I run the command show vlan local VoIP on the SG300, I get the following result:

  VLAN ID - VPT DSCP Source MAC address Interface

  1                    5          46       default           ----                    ---

  * 100 CDP e0:5f:b9:xx:yy:zz gi28

  Thus, it is clear that the SG300 receives information from UC560 via CDP in port Gi28 VLAN 100 is the voice VLAN. However, I can not always apply the ip_phone_desktop macro to SG300 Gi15 interface.

  Also, I tried to set up vState ofoithis vlan auto-déclenché as well as the commands in global configuration State vlan automatic voice activated mode. Or setting changes anything view voice VLAN announced at Cisco 7965 where Cisco 7965 continues to use VLAN101 (access the VLAN assigned to the interface Gi15).

  Hello telecastle,

  The Macro just get in the way most of the time. A default state on the switch a user will set the id of the vlan voice with orders

  (config) #voice vlan id 100

  * This will create the vlan 100

  VLAN, VoIP? * You can use to change your defaults for dscp and cos a long with all the other settings.

  State of vlan (config) enabled automatic #voice

  (config) #interface rank fa1-24

  (config-if-range) #switchport trunk vlan 101 native

  trunk (config-if-range) #switchport allowed vlan add 100

  * This function will define the vlan native on the trunk to 101 for the data port and vlan tagged will be 101 for the voice.

  CDP is enabled automatically and should learn the features of the phone and get on the phone to the vlan 101 on this port.

  CDP of the UC should automatically fill in the switch of the SG. You may need to upgrade the switch to the latest firmware however. Also make sure that the DHCP server for the voice if the CPU must be configured accordingly.

  Let me know if this helps.

  Cisco Small Business Support Center

  Randy Manthey

  CCNA, CCNA - security

• Command switchport mode access

  Hello

  I was curious about the switchport mode access command and its interoperability with the switchport command in vlan voice.

  If I set up a switchport with the switchport mode access commmand, which will make it impossible for the switchport create a trunk special cases with the IP phone? Even if I set up switchport vlan speech?

  And if so, the port should be configured as switchport mode dynamic auto? Or desirable?

  Thank you, Pat

  Pat, you can configure a port as an access port, add the configuration of vlan voice and connect a phone and another device. The trunk will form. With the "vlan voice" Cisco obscures the fact that forms a trunk. I don't necessarily agree with this strategy, and it wasn't always in this way. I remember configuration of phones on a 3500XL and ports have been configured in trunks.

  You made me think, so I issued a few commands on a WS-C3560V2-48PS-S running IOS 12.2 (58) SE2 who has 12 phones connected on it.

  Here is the config for a port that has a connected phone:

  Switch #sho int f0/2nd round

  Building configuration...

  Current configuration: 475 bytes

  !

  interface FastEthernet0/2

  switchport access vlan 11

  switchport trunk encapsulation dot1q

  switchport trunk vlan 11 native

  switchport trunk allowed vlan 2, 10-19

  switchport mode access

  switchport nonegotiate

  switchport voice vlan 12

  SRR-queue bandwidth share 1 30 35 5

  priority queue

  MLS qos trust device cisco-phone

  MLS qos trust cos

  Auto qos voip cisco-phone

  No auto mdix

  spanning tree portfast

  service-policy input AUTOQOS-SRND4-CISCOPHONE-POLICY

  end

  If I show the status of the trunk for an individual port that IOS recognizes that the port with the attached telephone is actually a trunk:

  Switch #sho int f0/2 trunk

  VLAN Mode Encapsulation native port State

  FA0/2 off 802. 1 q non-gaine 11

  Port VLAN allowed on trunk

  FA0/2, 11-12

  Port VLAN authorized and active in the field of management

  FA0/2, 11-12

  VLAN port extending on transmission State and no tree pruned

  FA0/2, 11-12

  However if I do a "sho int trunk" to display all the ports on the switch IOS trunk does not include telephone ports in the output.

  Trunk switch #sho int

  VLAN Mode Encapsulation native port State

  FA0/45 on 802. 1 q 12 trunking

  FA0/46 / 802. 1 q 12 trunking

  Gi0/1 on 802. 1 q sheath 11

  Gi0/2 of 802. 1 q sheath 11

  Port VLAN allowed on trunk

  FA0/45 2: 10-19

  FA0/46 2: 10-19

  Gi0/1, 2, 10-19

  Gi0/2, 2, 10-19

  Port VLAN authorized and active in the field of management

  FA0/45 13, 16-2, 11-17

  FA0/46 13, 16-2, 11-17

  Gi0/1, 2, 11-13, 16-17

  Gi0/2 13, 16-2, 11-17

  VLAN port extending on transmission State and no tree pruned

  FA0/45 13, 16-2, 11-17

  FA0/46 13, 16-2, 11-17

  Gi0/1, 2, 11-13, 16-17

  Gi0/2 13, 16-2, 11-17

  So firstly IOS says "Yes, it is a trunk" and on the other hand it is said ' Nope, no trunks here! So notice that 'spanning-tree portfast' is configured on f0/2, no 'portfast spanning-tree trunk. PortFast is still active on this port.

  Switch #sho span int f0/2 selection

  VLAN0011 enabled

  VLAN0012 enabled

  Conversely on 45 port, we have a VG-224 connected and it is configured with "switchport mode trunk" and "trunk spanning-tree portfast '. If I change than just "spanning-tree portfast' we see this:

  Switch #sho span int f0/45 selection

  VLAN0002 disabled

  VLAN0011 disabled

  VLAN0012 disabled

  VLAN0013 disabled

  VLAN0016 disabled

  VLAN0017 disabled

  Cisco has confused the issue here. I would prefer if we called a trunk, a trunk, but for some reason, they do not.

  See you soon,.

  -Jeff

  ---

  Posted by Jeff Davis of the Cisco support community App WebUser

• SG300 voice vlan problem with UC520

  Salvation of the Forumers

  My problem statement:

  -Secretary referred to topology.png, this is how my network like structure look

  -the IP phone after startup can not connect, so it cannot download the XML of UC520 configuration file. problem switching suspects.

  -my configuration illustrated in topology.png and my config show vlan as the voice setting.png voice vlan

  -My requirement is switch SG300 unique switchport to carry data VLANs and vlan voice.

  -What is the mode of connection for voice siwth VLAN an IP phone + data must be set up? is it switchport voice vlan vvid switchport voice vlan dot1p, switchport voice vlan unidentified or vlan switchport voice no further action over requirement?

  Thank you

  Noel

  Christmas morning,

  Sorry for the late reply, things have been very hectic in here lately

  1. Why use trunk? the UC520 don't have voice vlan (vlan 20)

  Do you mean that data THAT VLAN is handled by another device? Again I would like to leave as a trunk in order to manage the CPU through the data VLAN. (Except for security or other reasons you would choose differently of course)

  2. the UC520 got CUE (voicemail), how should I design the uplink service for the main switch module?

  Nothing in particular needs to be done for this, CUE is processed and routed inside the UC520, the vlan (default ID = 90) CUE is used if you have another LANDMARK in the network

  1. I guess I did: swithcport the tag vlan vlan unlabelled 20, 10. is it ok for this setting?

  If the Vlan on the switch and the UC520 voice has been defined as VLAN 20 (default value = VLAN 100) it's perfect. Check if the CPU and the switch, the voice VLAN ID is set to 20.

  1 so if I have just the phone to vlan 20 (vlan voice), create the policy of network LLDP?

  If you are ready to configure the VLANS manually on the phone, you don't need politics LLDP, thats right.

  Politics LLDP is used to having phones automatically choose the VLAN you set, so you do not need to set it manually.

  I hope that answers your questions?

  Best regards

  Nico glacier

  Senior Network Engineer - CCNA

• problem with dhcp Cisco sg200 voice vlan

  I have cisco sg200 50 p connected to the switch cisco 3750. I just wanted to separate voice (vlan2) and data (vlan1) VLAN. I created vlan 2 as my voice VLAN and separate dhcp server for vlan 2 to give IPS for phones. However the phone ip connected to my voice vlan (vlan 2) does not receive the ip address of my dhcp server vlan 2.

  the dhcp server is connected to a switch with an access port (vlan2-voice) 3750

  two switches are connected through the trunk ports and allowed vlan 1 & 2

  IP phone is connected to sg200 via the access port (vlan 2).

  Note: there is a pc connected to the ip phone

  I'm really grateful if someone can help me with this problem

  Hi Ruchiran,

  To cover the base, ensure that VLAN 2 is added to the database VLAN on the 3750. Simple by using the command "show vlan id 2", if it is not found, you must first create the VLAN 2 on the 3750.

  Second, if you connect the same IP phone directly to the 3750 on an access port, vlan 2 unidentified, is the phone receives IP address as you hope?

  Then, on the trunk of 3750 connection to the SX200. Building the trunk when using a command like "switchport trunk allowed vlan remove 1-4094," then build the trunk more precisely with the VLAN ' trunk switchport allowed vlan add 2 "who will score 2 VLAN port." "

  On the SG200 switch, must be defined the trunk and VLAN Tag 2 on the port to connect to 3750 then the connection to the phone port should be 2 VLANS not identified as access port.

• Reference Dell 6200 Voice Vlan

  Hello

  Could someone show the config complete for the vlan voice with a VLAN for data on the same port it please?

  I currently have all the switchports in one vlan 10 normal data, the phone system and phones are also in this vlan. However, I now want to put phones on one vlan separate voice sharing the same port.

  My current Config is:

  Configure

  database of VLAN

  VLAN 10

  interface vlan 10

  name of 'NETWORK '.

  Routing

  IP 192.168.10.1 255.255.255.0

  interface ethernet 1/g1

  spanning tree portfast

  switchport access vlan 10

  output

  In my understanding, I have to do the following:

  Configure

  database of VLAN

  VLAN 20

  interface vlan 20

  name of the "voice."

  Routing

  address 192.168.20.1 255.255.255.0

  interface ethernet1/g1

  spanning tree portfast

  switchport mode general

  pvid switchport General 10

  VLAN 20 voices

  output

  Thanks for any help you can give, it's urgent fairy we should have had this work tonight :(

  Here is an example of a configuration of VLAN basic votes for a port to have a phone and workstation on this subject, with each device traffic, separated from each other.

  Example:

  VLAN 100 is set up for voice *.

  VLAN 10 is set up for data. ****

  Console (config) # vlan VoIP

  Console (config) # interface ethernet 1/g20-1/g24

  Mode console # switchport general

  Console # switchport General allowed vlan add 100 tag

  Console # switchport General allowed vlan add 10 untagged

  Console # pvid general switchport 10

  Console # switchport general allowed vlan remove 1

  Console # vlan 100 VoIP

  Console # end

  There is also this white paper with some good info in there.

  www.Dell.com/.../pwcnt_voice_VLAN_support.pdf

  Hope this helps some.

  See you soon

• Voice VLAN with SRW224G4P

  Hi all

  I tried to config a vlan voice in this switches for the last 3 hours and for me it's impossible... I know how to do it in a switch IOS but with this switches is a nightmare...

  I have this topology

  PC - telephone to IP - SW1 SRW224G4P - SWCORE SRW2024 - router 2921 CME

  I have this config in my router,

  interface GigabitEthernet0/0

  no ip address

  automatic duplex

  automatic speed

  !

  interface GigabitEthernet0/0.1

  LAN description

  encapsulation dot1Q 1 native

  IP 192.168.5.95 255.255.255.0

  IP virtual-reassembly in

  !

  interface GigabitEthernet0/0.100

  Description VLAN VoIP

  encapsulation dot1Q 100

  IP 192.168.251.1 255.255.255.0

  IP virtual-reassembly in

  !

  SW1 created the VLAN 100 and activated as VLAN VOIP

  The first 3 octes for the mac on my phone is inserted into the Table YES telephony

  Belonging to a VLAN automatic voice is enabled in the port where the phone is attached.

  The port connected to the SWCORE has the vlan configured as labeled 100.

  SWCORE has created the VLAN 100 and activated as VLAN VOIP

  The port connected to SW1 has the vlan configured as labeled 100.

  The port connected to the router CME has the vlan configured as labeled 100.

  If I have another config port in SWCORE with 100 VLAN Tag I can ping from FMC to this host.

  Could be the problem, an error of spread vlan?

  Could someone help me? I'm desperate...

  Thank you in advance.

  Hi David,

  Thank you for the purchase of the switch.

  . Like what, even riding a bike, the switch is actually very easy to set up, if you practice on it...

  You mentioned that you use the 'phone YES picture' I assume you have a SF300 - 24 p or p/n command SRW224G4P-K9-NA.  Please be specific with the models of switches you use.

  Using the old SRW series or refreshed in the kernel SRWxxx-K9 (300 series) switch?

  First of all, make sure that you are using version 1.1.0.73 of the switch firmware. This change now or check that 1.1.0.73 is the active image on the switch.

  The switch has two areas to store the firmware images.  It stores the new firmware in the area of the image unused.  The administration for the firmware update Guide and select new firmware for the next reboot.

  CDP is enabled on the switch when using the new software, did not exist with older firmware, where my insistence to upgrade the firmware.

  ( Personally I would prefer that you have a role of catalyst for switching to your CME ISRG2 application, for purposes of support tech.) But this is the land of freedom..)

  I found the following when I added my SG300 - 28 p to a conscious UC500 of VLAN.

  The UC500 was vlan100 of advertising as a vlan voice, configured by Cisco Configuration Assistant, you could try CCP on your ISR.

  I got an IP phone that is plugged into the port of switch in the G7 and uplink to my UC500 via the Gig27 port.

  What follows in blue is a screenshot of my 300 series switch CLI interface.

  You will notice that the switch already filled both VLAN and port information, the only command that I added was "don't activate any complexity of passwords" and some usernames, including free from the screenshot below.

  the configured basically switch itself.

  -See the establishment of the system-

  Description of the system: 28 ports Gigabit PoE managed switch

  System of the time (days, hours: min: sec): 00, 00:12:04

  Contact system:

  Name of the system: switch4cf17c

  System location:

  System MAC Address: d0:d0:fd:4 c: f1:7 c

  System object ID: 1.3.6.1.4.1.9.6.1.83.28.2

  Fans Status: OK

  -See the version-

  SW version 1.1.0.73 (date, June 19, 2011 time 18:10:49)

  Start the version 1.0.0.4 (April 8, 2010 time 16:37:57)

  HW version V01

  Location of activity IP gateway Type.

  ----------------------- ----------------------- --------

  192.168.10.1 active dhcp

  IP address I / F Type of status

  ------------------- --------- ----------- -----------

  192.168.10.17/24 vlan 1 DHCP valid

  -show ipv6 interface-

  IPv6 is disabled on all interfaces

  -show running-config-

  interface gigabitethernet7

  Storm-control broadcast level 10

  output

  interface gigabitethernet7

  Storm-control include multicast

  output

  interface gi27

  point to point spanning tree-type of link

  output

  database of VLAN

  VLAN 100

  output

  Add a voice vlan Yes-table 0001e3 Siemens_AG_phone___

  Add a voice vlan Yes-table 00036 b Cisco_phone___

  Add a voice vlan Yes-table 00096e Avaya___

  Add a voice vlan Yes-table 000fe2 H3C_Aolynk___

  Add a voice vlan Yes-table 0060 b 9 Philips_and_NEC_AG_phone

  Add a voice vlan Yes-table 00d01e Pingtel_phone___

  VLAN voice Yes-table add Polycom/Veritel_phone___ 00e075

  Add a voice vlan Yes-table 00e0bb 3Com_phone___

  hostname switch4cf17c

  No complexity of passwords allow

  No server snmp Server

  interface gigabitethernet7

  macro description ip_phone_desktop

  output

  interface gigabitethernet27

  description of the macro "pass | valeur_log | switch ".

  output

  interface gigabitethernet7

  ! next order is internal.

  macro auto smartport dynamic_type ip_phone_desktop

  switchport trunk allowed vlan add 100

  output

  interface gigabitethernet27

  ! next order is internal.

  switch dynamic_type macro auto smartport

  switchport trunk allowed vlan add 100

  output

  switch4cf17c #sh cdp nei

  Ability code: R - router, T - bridge Trans, B - road Source bridge

  S switch, H - host, I - IGMP, r - Repeater, P - VoIP phone

  M - managed remote-device, C - CAST phone Port,

  W - two port MAC relay

  Device ID Local time from Port platform capacity ID Adv

  The interface direct worm.

  ----------------- ----------- ---- ------- ---------- ------------ -----------

  SEP503De50F133A gi7 2 158 H P CISCO IP eth0

  Phone

  SPA525G2

  68bdab0fdcfd gi27 2 169 S I Cisco SG gi9

  300 10 P

  (PID:SRW2008P - K9) - VOD

  switch4cf17c #sh vlan

  VLAN name Ports type permission

  ---- ----------------- --------------------------- ------------ -------------

  1 1 article gi1-28, required to Po1 - 8 by default

  100 100 gi7, required permanent gi27

  Automatically numbers which ports need to be listed in VLAN 100.

  I did not switch it was connected to VLAN100. I don't have add vlan100 to the database for VLAN.

  Get the ISR router to announce VLAN100 as a vlan voice.

  Best regards, Dave

• Unable to see 'add a trunk switchport allowed vlan' lines in the running-config

  Hello!

  I use a configuration on a bunch of N3000 and N4000 switches (with firmware 6.3.x.x). I try to create the VLAN on the links and I am facing some problems (maybe).

  In the configuration of the interface if I send the command 'trunk switchport allowed vlan add [vlan]' and check the running configuration I can't see the line.

  The command show vlan shows VLAN seems them ok.

  I have a few configuration files archive and in these cases him vlan said add visible function. What could be the cause of this difference?

  Hi Adam,.

  OS6 is sometimes unpredictible :) Basically, you must use Add or remove the commands when you have got all the restrictions on the configured trunk.

  switchport mode trunk add all the VLANS on trunk (including for example VLAN1) port. At this point, you can delete only the VLAN of the trunk. This is the reason why you don't see the configuration changes to the example runn.

  Initially limit the VLAN allowed on trunk port starting with:

  switchport trunk allowed vlan "vlan numers '

  (eg. trunk allowed vlan switchport 10 with allowed vlan 10-25 range or after coma allowed vlan 10,11,15)

   

  After that you can use Add or remove commands you want :)

  Best regards

  GB

• Having trouble getting the voice VLAN on the switch X1052P to work at all

  Can someone help me understand how to set up the voice VLAN X1052P? I spent several hours trying to get this working and it does not work. I spent about 4 hours on the phone with a Dell technician that night and he couldn't get it to work and finally gave up. He told me that I had to spend my warranty to ProSupport because he did not know how to solve the problem. What group of *. It's a simple configuration of VLAN. What must be so picky about? In any case...

  Setting up the VIRTUAL LAN must be fairly simple, but apparently on this switch is not. The user guide page 406 is not very useful except explaining what the different options. I must admit I am not an expert VLAN so I dunno I've misconfigured something. But remember, Dell technology could not operate either.

  Here's my situation... I have VoIP phones on my network connected to a network wall jack. Connected to phones are my computers of users. The computer of the user and its respective VoIP phone, both share the same data cable. Before replacing Cisco managed Internet service provider spend all it worked well. The problem is that they had direct access to our network so I removed the switch and installed the X1052P in its place. I talked to the ISP to let them know what I'm doing and they said everything I had to do was setup VLAN ID: 15 for the voice VLAN because this is the VLAN ID that the router uses to route telephone traffic. Router PSI is also the server DHCP VLAN 15 and issues IP for phones using 172.27.0.0/24 with a DHCP 172.27.0.50 range - 150.

  I tried to configure the switch using parameters of VLAN static and settings VLAN voice and neither one also seems to do what I want it to do.

  Network administration > VLAN > VLAN static

  Network administration > VLAN > Voice VLAN

  I activated the profile 'phone' on ports I want to added to the voice VLAN and it does not work. Moreover, 47 the switch port is connected directly to the ISP router and is configured as a trunk with the default port VLAN 1 unidentified and tag VLAN 15. For other ports I tried the general implementation, access and trunk of the parameters on each port to see if I could get something going and still nothing happens. When I set up the ports as General ports VLAN, I made adding VLAN VLAN 1 and VLAN 15 as a VLAN tagged not marked. It still does not.

  This is the short story from where I am now. Any help is greatly appreciated.

  FYI, as a follow up I finally solved the problem. I hope this information helps someone else that can encounter the same problem.

  After buying the ProSupport warranty upgrade ($121 out-of-Pocket mind you) and addressing a total of 4 technicians ProSupport expert technician a 3rd another level (only available via chat message between one of the ProSupport phone technicians and the 3rd Tier expert tech - i.e. I couldn't talk or chat with this person me) the consensus was that the material must be bad. When I bought the X1052P I bought two of them, so the best way to know if it was a bad switch was simply configure the other switch and see if the behavior occurs on this one, too. Well, this switch also restarted each time I assigned the profile 'phone' to more than 13 or 14 ports in the switch. It seems that it was not a hardware problem after all.

  I went back to the switch original and tried new things hoping that I could fall on a solution and it turns out that the solution was NOT to use the voice VLAN on the switch. It does not work!

  SOLUTION: I set the VLAN ID: 15 manually and no has not assigned any phone profiles to one of the ports. This is how I solved the problem.

  So he has bad software on the switch. I tried to see if there are updates of the firmware on the Dell support site, but there is none. Configure manually the phone VLAN was the solution. What a freaking nightmare which turned out to be. Maybe someone in Dell could note this problem and test in-house. And, if you want to compensate me for the 20 + hours I spent working on this problem, which has be great, too.

• Voice VLAN help please

  My client has 2 SG300 - 52p and 5 SG300 - 28 p. We have installed a VoIP telephony system earlier this year. At the time of installation, we placed the phone on the native VLAN 1 System. Now, they want to pass the phone system to a new VLAN, because their class C subnet is running out of addresses. DHCP is managed by their Active Directory and their router/firewall is a box to sort out. The SG300 switches have a basic configuration only.

  To move the phone system to a new VLAN, I created 20 VLAN on each switch. I then turned on VLAN auto voice. I have all the ports on each switch setting on the trunk. Computers are plugged into the back of the phone. I then created a virtual interface in the box to unravel for VLAN 20. Box unravel also manages DHCP to the new VIRTUAL LAN. Active Directory is always manage DHCP for VLANS native.

  I ping from each switch to the bridge of the new VLAN. Since each computer I can ping the gateway and on the new LAN VIRTUAL phone system. However, phones will not seize an address on the VIRTUAL LAN and when they have the static value, they cannot communicate with other devices on the VIRTUAL LAN.

  Any help would be much appreciated. I don't know what I'm on.

  Here is an example of part of a switch configuration to work with Zultys phones where voice VLAN is 100 and data VLAN 10:

  database of VLAN
  VLAN 10,20,100
  output
  ID of the vlan 100 voices

  interface fastethernet1
  Description "RCP and voice."
  switchport trunk allowed vlan add 100
  trunk switchport vlan 10 native
  !
  interface fastethernet2
  Description "RCP and voice."
  switchport trunk allowed vlan add 100
  trunk switchport vlan 10 native

  In your case, you need a trunk port with 20 VLAN Tag on your firewall (or an access port to a separate physical port on VLAN 20.  The default gateway served on the phone (or put statically) should be the interface on intellectual property.  Then, you can also allow routing inter - vlan for admin access or MXIE if you use.

  One thing to note on Zultys is by default I think the device profile disables LLDP, but on phones, it is enabled out of the box.  For the first time that a phone downloads its config from the Zultys it can turn of LLDP unless you have checked the box to keep it on.

• Update Tandberg E20 TE2.1.0 TE4.1.1. Phone is set to both data & Voice VLAN

  I've updated a Tandberg E20 TE2.1.0 to TE4.1.1 (without encryption) phone is now appear in the two VLANS data & voice/video.

  It seems that the voice traffic and data is properly managed, due to the fact that when I STOP the audio/video/VLAN no appeal that can be sent or received.

  Q: do I need to worry about why the phone of Tandberg is now appear in the two VLANS data & voice/video?

  Thank you, Scott

  Hello

  I think what happens is that when the device is initializing, DHCP tries to get the IP address to the VLAN 100 native. After that CDP discovers there is a voice VLAN, endpoint application address DHCP VLAN 11. So you see twice MAC:

  #sh table of mac addresses

  Mac address table

  -------------------------------------------

  VLAN Mac Address Type Ports

  11 0050.6004.2451 DYNAMICS Gi0/2 / / Tandberg E20

  100 0050.6004.2451 DYNAMICS Gi0/2

  If you open the MAC address table, the entry for 100 will disappear [I hope].

  The other entrance to the connected PC is normal.

  #sh table of mac addresses

  Mac address table

  -------------------------------------------

  VLAN Mac Address Type Ports

  100 1803.73e3.083c DYNAMICS Gi0/2 / / workstation connected to E20

  We have a DDT where we would not obtain a correct address in the case of CDP Auto: CSCtx84402.

  Should be fixed in the TC6 release.

  Danny.

• Is there a firefox command argument to load firefox in 32-bit mode?

  Hello

  I RHEL6.3, I have the 32-bit versions and 64-bit of Firefox (V10.0.7) installed. I need 32 bits for WebEx (Java plugin) and the 64-bit Flash player.
  Currently, I load the 32-bit executable file by running:
  / usr/lib/Firefox/Firefox

  Is there a firefox command argument to load firefox in 32-bit mode?
  for example firefox-32 b

  Thanks in advance,
  Simon

  32-bit and 64-bit versions are different programs and therefore installed in a directory of different programs, so you must start them in their own program directory.
  
  If you want to start them via a command then you must write a script file to define the correct program directory.

  Why don't create you two desktop shortcuts for each of the two versions of Firefox and start them with their own profile?

• are there options of command line for wuapp.exe (windows update)?

  I have some Vista virtual machines set up to perform specific tasks, then stop - these VMs run at specific times, as if a physical computer running, ran a task, then stop.  I want to be able to automate the Vista updates without having to manually open each VM on a weekly basis.  Are there options for command line for wuapp.exe so that I can program the virtual machine to turn on, install updates, and then click Stop again?  Or y at - it another way to accomplish what I'm doing?

  Thank you

  Hi Prisoft,
  
  Welcome to the responses of Microsoft Vista Forums!

  The question you posted would be better suited to the TechNet community. Please visit the link below to find a community that will provide the best support.
  http://social.technet.Microsoft.com/forums/en-us/category/windowsvistaitpro/

  With regard to:

  Divya R -Microsoft Support

  --------------------------------------------------------------------------

  Visit our Microsoft answers feedback Forum and let us know what you think

• PC8024 interface with existing voice VLAN (100) on the switches HP 2910

  We have added our first Dell PowerConnect 8024 switch to an existing network of switches HP 2910.  We have only 2 VLANS configured: voice (100) and default (1).  The switches HP all default ports VLAN are set to "no label" and all the ports on the voice VLAN are established 'labelled '.

  I need to configure the PC8024 to co-exist with the existing network phones for Mitel can communicate.  We are not familiar with the PC8024 switch, evaluate as a possible solution for improving our spine and DR subnet 1 GB to 10 GB.  For the spine, we need the voice traffic to be handled properly, so we set up the work with the existing voice VLANS 8024.

  What parameters of configuration of VLAN do we need on the PC8024 to co-exist with the existing network configuration for the (100) voice VLAN on HP switches?

  Voice VLAN allows you to specify which VLANs, then you should be able to use the VLAN 1, but if you use VLAN 1 and 100, you could probably just create a VLAN 100 and not bother with the stuff of vlan voice. What type of port is the port you are trying to assign to tagged in? Access mode cannot do without label. If it was the general mode you can assign it labeled 100 and a PVID from 1 which would put traffic which is not marked on the vlan 1.

• SG200 - 50 p, SG300 - 28 p phone YES Voice VLAN

  Hey guys,.

  I'm having a problem with the YES voice of VLANS on SG200 - 50 p, SG300 - 28 p, layer 2 Mode. Firmware 1.3.7.18.

  Enabled on a port all the ports PVID unlabeled said no marked traffic is blocked.

  Example:

  Data VLAN 10 - 192.168.10.0/24

  Voice VLAN 100 - 192.168.100.0/24

  Configuration of Vlan voice and YES added and enabled on ports.

  All Ports configured as trunk Type.

  Example 1:

  Members Table shows that:

  Port 1 - 10UP

  2 port - 10UP

  YES disabled: 2 laptops connected to ports 1, 2, traffic passes.

  YES Enabled: 2 laptops connected to ports 1, 2, traffic blocked on VLAN10.

  Example 2:

  1 - 10UP, 100 tons of port

  2 port - 10UP

  Port 3 - 10UP

  YES Enabled: 2 laptops connected to the ports 2,3, blocked traffic on VLAN10.

  1 phone connected to channel 1, the phone connects.

  So it's using, but for some reason any the vlan untagged on that port is blocked when the YES is enabled.

  I have installation this scenario on many switches cisco small business before and it works very well, so I wonder is this a firmware issue? or am I just being stupid and something wrong?

  Thanks for any help you can provide! :)

  Hi Vladimir,.

  It's something about Cisco still working. You are more than welcome to open the ticket with us and contribute actively. At this point, the only solution is to sue 1.3.5 firmware which does not show this problem.

  http://www.Cisco.com/c/en/us/support/Web/TSD-Cisco-small-business-suppor...

  Kind regards

  Aleksandra