SG200 - 50 p, SG300 - 28 p phone YES Voice VLAN

Similar Questions

• Need help to set up voice VLAN in SG300

  Hello

  I spent too much time on it now and need help. I'm trying to set up a voice switch VLAN on a SG300 - 28 p. I need to charge a phone Cisco 7965 connected to a port on SG300 - 28 p to use VLAN 100, and a workstation connected to the phone to use Cisco 7965 on VLAN 101 by SG300 - 28 p. In the common Cisco IOS switches, this task is configured as follows:

  interface gi25

  switchport mode access

  switchport access vlan 101

  switchport voice vlan 100

  Trying to achieve this scenario with a Cisco SG300 switch turns into a nightmare. You will have to deal with a Dynamic of VLAN voice Auto Voice VLAN mode. Then, you must have a configured trigger and activated Automatic Smartport . I tried to do this in CLI nothing helps. Cisco 7965 receives an IP address of the access VLAN on Gi15 interface, which is 101 VLAN. I need to receive an address IP of the VLAN 100.

  The current configuration under Gi15 interface is as follows:

  interface gigabitethernet15

  activate the storm control

  broadcast storm control level kbit/s 10

  Storm-control include multicast

  port security throw trap 60

  maximum port security by 10 points

  port security mode max-addresses

  spanning tree portfast

  LLDP-med disable

  switchport mode access

  switchport access vlan 101

  ! next order is internal

  macro auto smartport dynamic_type unknown $native_vlan 101 $voice_vlan 100

  Now, I don't know how the macro auto smartport dynamic_type unknown $native_vlan 101 $voice_vlan 100 command in the config, and I do not know how to remove it.

  When I try to enter the command macro auto smartport type ip_phone_desktop under Gi15 interface, I get the following error message:

  The $voice_vlan macro setting is not configurable by the user

  It seems that the auto attendant smartport macro ip_phone_desktop can not apply the setting $voice_vlan with a value of 100. In fact, I explicitly does not use this parameter to everything in the order of macro auto smartport type ip_phone_desktop ; However, the SG300 switch knows that the voice VLAN VLAN 100, and he's trying to use this VLAN ID as the value of the $voice_vlan parameter, the macro fails.
  

  I tried statically configure the voice VLAN on the switch SG300 using the command id of the vlan 100 voice , but I couldn't get the ip_phone_desktop macro to configure interface Gi15 correctly. Then, I removed the command id of the vlan 100 voice and obtained SG300 to learn his voice VLAN ID of UC560 connected to the SG300 through a trunk port based on the port configuration (connected to SG300) for the trunk of the next UC560:

  switchport trunk vlan 101 native

  switchport mode trunk

  switchport voice vlan 100

  Cisco-switch macro description

  This is the command switchport voice vlan 100 who announces to SG300 via CDP VLAN 100 is a voice VLAN. When I run the command show vlan local VoIP on the SG300, I get the following result:

  VLAN ID - VPT DSCP Source MAC address Interface

  1                    5          46       default           ----                    ---

  * 100 CDP e0:5f:b9:xx:yy:zz gi28

  Thus, it is clear that the SG300 receives information from UC560 via CDP in port Gi28 VLAN 100 is the voice VLAN. However, I can not always apply the ip_phone_desktop macro to SG300 Gi15 interface.

  Also, I tried to set up vState ofoithis vlan auto-déclenché as well as the commands in global configuration State vlan automatic voice activated mode. Or setting changes anything view voice VLAN announced at Cisco 7965 where Cisco 7965 continues to use VLAN101 (access the VLAN assigned to the interface Gi15).

  Hello telecastle,

  The Macro just get in the way most of the time. A default state on the switch a user will set the id of the vlan voice with orders

  (config) #voice vlan id 100

  * This will create the vlan 100

  VLAN, VoIP? * You can use to change your defaults for dscp and cos a long with all the other settings.

  State of vlan (config) enabled automatic #voice

  (config) #interface rank fa1-24

  (config-if-range) #switchport trunk vlan 101 native

  trunk (config-if-range) #switchport allowed vlan add 100

  * This function will define the vlan native on the trunk to 101 for the data port and vlan tagged will be 101 for the voice.

  CDP is enabled automatically and should learn the features of the phone and get on the phone to the vlan 101 on this port.

  CDP of the UC should automatically fill in the switch of the SG. You may need to upgrade the switch to the latest firmware however. Also make sure that the DHCP server for the voice if the CPU must be configured accordingly.

  Let me know if this helps.

  Cisco Small Business Support Center

  Randy Manthey

  CCNA, CCNA - security

• problem with dhcp Cisco sg200 voice vlan

  I have cisco sg200 50 p connected to the switch cisco 3750. I just wanted to separate voice (vlan2) and data (vlan1) VLAN. I created vlan 2 as my voice VLAN and separate dhcp server for vlan 2 to give IPS for phones. However the phone ip connected to my voice vlan (vlan 2) does not receive the ip address of my dhcp server vlan 2.

  the dhcp server is connected to a switch with an access port (vlan2-voice) 3750

  two switches are connected through the trunk ports and allowed vlan 1 & 2

  IP phone is connected to sg200 via the access port (vlan 2).

  Note: there is a pc connected to the ip phone

  I'm really grateful if someone can help me with this problem

  Hi Ruchiran,

  To cover the base, ensure that VLAN 2 is added to the database VLAN on the 3750. Simple by using the command "show vlan id 2", if it is not found, you must first create the VLAN 2 on the 3750.

  Second, if you connect the same IP phone directly to the 3750 on an access port, vlan 2 unidentified, is the phone receives IP address as you hope?

  Then, on the trunk of 3750 connection to the SX200. Building the trunk when using a command like "switchport trunk allowed vlan remove 1-4094," then build the trunk more precisely with the VLAN ' trunk switchport allowed vlan add 2 "who will score 2 VLAN port." "

  On the SG200 switch, must be defined the trunk and VLAN Tag 2 on the port to connect to 3750 then the connection to the phone port should be 2 VLANS not identified as access port.

• SG300 voice vlan problem with UC520

  Salvation of the Forumers

  My problem statement:

  -Secretary referred to topology.png, this is how my network like structure look

  -the IP phone after startup can not connect, so it cannot download the XML of UC520 configuration file. problem switching suspects.

  -my configuration illustrated in topology.png and my config show vlan as the voice setting.png voice vlan

  -My requirement is switch SG300 unique switchport to carry data VLANs and vlan voice.

  -What is the mode of connection for voice siwth VLAN an IP phone + data must be set up? is it switchport voice vlan vvid switchport voice vlan dot1p, switchport voice vlan unidentified or vlan switchport voice no further action over requirement?

  Thank you

  Noel

  Christmas morning,

  Sorry for the late reply, things have been very hectic in here lately

  1. Why use trunk? the UC520 don't have voice vlan (vlan 20)

  Do you mean that data THAT VLAN is handled by another device? Again I would like to leave as a trunk in order to manage the CPU through the data VLAN. (Except for security or other reasons you would choose differently of course)

  2. the UC520 got CUE (voicemail), how should I design the uplink service for the main switch module?

  Nothing in particular needs to be done for this, CUE is processed and routed inside the UC520, the vlan (default ID = 90) CUE is used if you have another LANDMARK in the network

  1. I guess I did: swithcport the tag vlan vlan unlabelled 20, 10. is it ok for this setting?

  If the Vlan on the switch and the UC520 voice has been defined as VLAN 20 (default value = VLAN 100) it's perfect. Check if the CPU and the switch, the voice VLAN ID is set to 20.

  1 so if I have just the phone to vlan 20 (vlan voice), create the policy of network LLDP?

  If you are ready to configure the VLANS manually on the phone, you don't need politics LLDP, thats right.

  Politics LLDP is used to having phones automatically choose the VLAN you set, so you do not need to set it manually.

  I hope that answers your questions?

  Best regards

  Nico glacier

  Senior Network Engineer - CCNA

• Update Tandberg E20 TE2.1.0 TE4.1.1. Phone is set to both data & Voice VLAN

  I've updated a Tandberg E20 TE2.1.0 to TE4.1.1 (without encryption) phone is now appear in the two VLANS data & voice/video.

  It seems that the voice traffic and data is properly managed, due to the fact that when I STOP the audio/video/VLAN no appeal that can be sent or received.

  Q: do I need to worry about why the phone of Tandberg is now appear in the two VLANS data & voice/video?

  Thank you, Scott

  Hello

  I think what happens is that when the device is initializing, DHCP tries to get the IP address to the VLAN 100 native. After that CDP discovers there is a voice VLAN, endpoint application address DHCP VLAN 11. So you see twice MAC:

  #sh table of mac addresses

  Mac address table

  -------------------------------------------

  VLAN Mac Address Type Ports

  11 0050.6004.2451 DYNAMICS Gi0/2 / / Tandberg E20

  100 0050.6004.2451 DYNAMICS Gi0/2

  If you open the MAC address table, the entry for 100 will disappear [I hope].

  The other entrance to the connected PC is normal.

  #sh table of mac addresses

  Mac address table

  -------------------------------------------

  VLAN Mac Address Type Ports

  100 1803.73e3.083c DYNAMICS Gi0/2 / / workstation connected to E20

  We have a DDT where we would not obtain a correct address in the case of CDP Auto: CSCtx84402.

  Should be fixed in the TC6 release.

  Danny.

• Restricted Inter-VLAN with SG200-26 and SG300-10 routing

  Hi all

  My apologies if this has been covered elsewhere.

  My organization would like to organize a LAN game activity. The installation program I have in mind involves a switch 24 ports to connect all computers in player and saw that the switch connected to a smaller 'core' which has the connected the router and game server. I would like to know if I can put things up as follows...

  SG200-26 with 1 to 24 ports on VLANS separated so they can talk to eachother. I'd then ports 25 and 26 to be a trunk aggregated (for bandwidth and redundancy) port to carry all 24 VLAN more an additional management VLAN (VLAN 100 e.g.) that will be used to access the switch. I want these aggregated trunk ports to connect to a 'core' SG300-10 switch that is connected to the game server and a router for internet access.

  I would like to than the possibility of having two network connections of the server to the switch, one on the management of VLANS and the other on a VLAN different (e.g. 50 VLAN) which will be accessible by players (ports 1-24 of SG200-26). The power switch needs to be able to perform routing inter - VLAN restricted, because it does not VLAN 1-24 of eachother talk but they can talk to VLAN server, but only through specific service ports (e.g. 12345, 12346 port). Is this possible?

  Also how I configure the SG300-10 to enable the VLAN 1-24 of VLAN 50, but not to talk or VLAN 100. So, I will probably have the router on its own LAN VIRTUAL (VLAN 60 ex.) and allow for VLAN 1-24 for access, but only via HTTP port 80 for web access.

  What do you think?

  Thank you.

  Hi Marc, the default gateway of the computers will be the SVI to the switch.

  Router-> couche3-> SG300 layer 2 SG300

  router is 192.168.1.1

  VLAN 1 in 300 SG is 192.168.1.100

  2 VLAN on 300 SG is 192.168.2.1

  SG300 layer 2 has a 1u, 2 t trunk.

  My computer to connect to an access port 2 unidentified on the layer 2 SG300.

  I am able to ping 192.168.2.1

  I am able to ping 192.168.1.100

  I can not 192.168.1.1 pnig

  The reason is that the router has no idea on this subnet so cannot send the package to the source 192.168.2.x subnet.

  The ACL and the basic connection are 2 different animals. The ACL is to prevent intervlan communication. The basic connection must be tags trunk and vlan or static routes.

  -Tom
  Please mark replied messages useful

• How to activate a SIM free iphone 6s plus will detect a sim? I don't want a cell phone or voice

  Apple iPhone 6 s more SIM more memory each option free latest OS and Applecare happened today. I have absolutely no need to voice or cell phone. A; I want to, it's an iPad the smallest size. When I try to turn it on I get a required message of SIM.  I used an iPhone 4 without a sim card, but it was destroyed... I use Tracfone voice and used 48 minutes over the past twelve years and do not want to waste money on the cell. How can I use it without a sim card?

  You need a sim card in the phone to activate or restore it... no way around that fact. So, beg, borrow, or buy a sim card if you want to activate the phone. You can remove the sim card when the phone is turned on.

• BlackBerry Bold 9700 smartphones may not use the phone for voice

  I could use the phone to talk about yesterday, today, it looks like by clicking in the background and can not hear the other party. The appeal says connected. Email is ok, ok, ok ok BBM, just the voice Internet service SMS does not work.

  V5.0.0.442 (Platform 5.1.0.121)

  Recharged using BB Desktop software. Service provider indicates phone is probably failed.

  It's either a problem with the speaker of the device or the headphone jack.  Try plugging in a few times and then try a phone call without it.

• When you try to activate by phone, you voice says the number you gave me (ID) is not valid.

  the sticker is no longer legible. When you telephone, you voice says the number you gave me (ID) is not valid. I entered the # repeatedly and even had someone make sure I'm there enter correctly.

  Hi kenw1955,

  You can follow the steps in the link below that relates to a similar question

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-windows_install/Windows-XP-Home-activation-window-fail-to-appear/855fe79d-3f8e-454c-b2ba-83486be5459f

  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base.
  How to back up and restore the registry in Windows

  If the problem persists, contact customer support

  How and when to contact Microsoft and support Customer Service

  http://support.Microsoft.com/kb/295539

• Voice vlan - SG200-50

  Hello

  I m a fan of IOS CLI. Its the first tiem I have to configure a switch of SB. Sound very confused, I want to setup an id of the vlan 200 voice. but I have the gift of seeing this value changes when I try to apply the smartport macro interface.

  It can change a smartport macro?

  Thank you.

  Hello Rafael,.

  Sorry for the confusion. Under management of VLAN > VLAN voice > properties, you can set the vlan voice.

  Let us know if we can be of further assistance.

  -David Aguilar

  Cisco Small Business Support Center

• Voice VLAN help please

  My client has 2 SG300 - 52p and 5 SG300 - 28 p. We have installed a VoIP telephony system earlier this year. At the time of installation, we placed the phone on the native VLAN 1 System. Now, they want to pass the phone system to a new VLAN, because their class C subnet is running out of addresses. DHCP is managed by their Active Directory and their router/firewall is a box to sort out. The SG300 switches have a basic configuration only.

  To move the phone system to a new VLAN, I created 20 VLAN on each switch. I then turned on VLAN auto voice. I have all the ports on each switch setting on the trunk. Computers are plugged into the back of the phone. I then created a virtual interface in the box to unravel for VLAN 20. Box unravel also manages DHCP to the new VIRTUAL LAN. Active Directory is always manage DHCP for VLANS native.

  I ping from each switch to the bridge of the new VLAN. Since each computer I can ping the gateway and on the new LAN VIRTUAL phone system. However, phones will not seize an address on the VIRTUAL LAN and when they have the static value, they cannot communicate with other devices on the VIRTUAL LAN.

  Any help would be much appreciated. I don't know what I'm on.

  Here is an example of part of a switch configuration to work with Zultys phones where voice VLAN is 100 and data VLAN 10:

  database of VLAN
  VLAN 10,20,100
  output
  ID of the vlan 100 voices

  interface fastethernet1
  Description "RCP and voice."
  switchport trunk allowed vlan add 100
  trunk switchport vlan 10 native
  !
  interface fastethernet2
  Description "RCP and voice."
  switchport trunk allowed vlan add 100
  trunk switchport vlan 10 native

  In your case, you need a trunk port with 20 VLAN Tag on your firewall (or an access port to a separate physical port on VLAN 20.  The default gateway served on the phone (or put statically) should be the interface on intellectual property.  Then, you can also allow routing inter - vlan for admin access or MXIE if you use.

  One thing to note on Zultys is by default I think the device profile disables LLDP, but on phones, it is enabled out of the box.  For the first time that a phone downloads its config from the Zultys it can turn of LLDP unless you have checked the box to keep it on.

• How to configure the VPN LAN to access the internet from the remote network

  I have set up for our project site to another Office VPN. Please join.
  Now I have already configured Site to site vpn between ASA 5510 and 1841 router.

  HQ LAN

  Branch of the LAN
                   10.2.1.0/24 > ASA 5510 1841 > > INTERNET < 1841=""> <> 10.30.3.0/24
  ^
  ^
  ^
  ^
  Call Manager
  No. 2851
  Now access from branch LAN LAN of HQ each other.

  I face problems that are
  (1) in the direction of LAN, they can access HQ LAN & resource, but cannot access the internet. I did not configure NAT on the router PH
  (2) can I access internet BRANCH LAN via HQ LAN INTERNET. Where can I access the Internet of general management of the LAN of the PH router directly while access to the VPN to the local network of HQ?
  (3) in the Site of the Directorate, phone hard cannot work but phone on PC can call to Headquarters. Hard IP phone are same in remote network (172.16.1.0/24 ). What's the problem? How can I configure separately?

  Please give advise me how should I do.

  Hello

  (1) in the direction of LAN, they can access HQ LAN & resource, but cannot access the internet. I did not configure NAT on the router PH

  Answer:

  You must configure the NAT and crossed to the ASA HQ so that the VPN branch router provides LAN and u-Turn, access to Internet of the SAA.  You must first seup NAT for the branch on the SAA router subnet, then you must type the command:

  permit same-security-traffic intra-interface

  Here's a great example for VPN client hairpining.

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml

  (2) can I access internet BRANCH LAN via HQ LAN INTERNET. Where can I access the Internet of general management of the LAN of the PH router directly while access to the VPN to the local network of HQ?

  Yes, you can

  (3) in the Site of the Directorate, phone hard cannot work but phone on PC can call to Headquarters. Hard IP phone are same in remote network (172.16.1.0/24 ). What's the problem? How can I configure separately?

  You must change your subnet VLANS to be different from the subnet HQ voice phone IP VOice VLAn, it should be fine.

  Kind regards

  Mohamed

• Connection Cisco SG300-10-Core Cisco 6513 for ShoreTel phones

  I have a new ShoreTel phone system will soon.  Configure a dhcp, including option 156 scope which is required for ShoreTel to obtain the configuration on ShoreTel phones and in order to get on the vlan correct voice on the phone.  I also created a new vlan 112 for the vlan voice.  When I plug directly into the Cisco 6513 Core switch, the phone starts fine, it gets its configuration and on the VLAN correct 112.

  We have a training room in which there will be a lot of users.  I ordered 6 Cisco small business 10port SG-300 POE switches for this training room.  I plugged the switch in a cable coming off the 6513 which is just an access port and in the vlan voice I created for phones shoretel VOIP:

  interface FastEthernet10/11
  switchport
  switchport mode access
  switchport voice vlan 112
  priority queue queue-limit 20
  WRR-queue random - detect min-threshold 1 30 40 50 60 70 80 90 100
  WRR-queue random - detect min-threshold 2 30 40 50 60 70 80 90 100
  WRR-queue random detection threshold min 3 30 40 50 60 70 80 90 100
  WRR-queue random detection max-threshold 1 70 80 90 100 100 100 100 100
  WRR-queue random detection max-threshold 2 70 80 90 100 100 100 100 100
  WRR-queue random detection threshold 3 70 80 90 100 100 100 100 100 max
  WRR-queue cos-map 1-3-1
  WRR-queue cos-1 6 4 map
  WRR-queue cos-map 2 6 0
  WRR-queue cos-map 2 8 2
  WRR-queue cos-map 3 1 7
  WRR-queue cos-map 3 8 3 6
  MLS qos trust dscp
  Storm-control broadcasts 20 h 00
  spanning tree portfast

  When I plug a phone directly into this cable the phone works very well.  When I plug a cheap cisco POE switch in I can get 3 phones works very well, but due to the amount of energy needed for this cheap a cisco switch it will give only 3 phones power.

  The real problem here is plug into small business cisco SG300-10port POE managed switch.  I thought I could just connect the switch to the port configured above right out of the box and plug in phones without a problem.  When I plug the switch and start plugging in ShoreTel phones, they do not start coming in and upward and actually had a few phones upward but then finally there is no tone and also later, they appear on the screen as a service not available.

  I have to configure a trunk port on a port on the SG300 and the Cisco 6513 for this to work?  Also I will need to VLAN configuration manually on the SG300.  Looks like that when I just plugged it in to the above configured the port on the SG300 it automatically create the vlan 112.

  Any help would be appreciated

  Thank you

  Dave

  Deleted

• Cisco SG300-10 Cisco 6513 and Shoretel phones

  I have a new ShoreTel phone system will soon.  Configure a dhcp, including option 156 scope which is required for ShoreTel to obtain the configuration on ShoreTel phones and in order to get on the vlan correct voice on the phone.  I also created a new vlan 112 for the vlan voice.  When I plug directly into the Cisco 6513 Core switch, the phone starts fine, it gets its configuration and on the VLAN correct 112.

  We have a training room in which there will be a lot of users.  I ordered 6 Cisco small business 10port SG-300 POE switches for this training room.  I plugged the switch in a cable coming off the 6513 which is just an access port and in the vlan voice I created for phones shoretel VOIP:

  interface FastEthernet10/11
  switchport
  switchport mode access
  switchport voice vlan 112
  priority queue queue-limit 20
  WRR-queue random - detect min-threshold 1 30 40 50 60 70 80 90 100
  WRR-queue random - detect min-threshold 2 30 40 50 60 70 80 90 100
  WRR-queue random detection threshold min 3 30 40 50 60 70 80 90 100
  WRR-queue random detection max-threshold 1 70 80 90 100 100 100 100 100
  WRR-queue random detection max-threshold 2 70 80 90 100 100 100 100 100
  WRR-queue random detection threshold 3 70 80 90 100 100 100 100 100 max
  WRR-queue cos-map 1-3-1
  WRR-queue cos-1 6 4 map
  WRR-queue cos-map 2 6 0
  WRR-queue cos-map 2 8 2
  WRR-queue cos-map 3 1 7
  WRR-queue cos-map 3 8 3 6
  MLS qos trust dscp
  Storm-control broadcasts 20 h 00
  spanning tree portfast

  When I plug a phone directly into this cable the phone works very well.  When I plug a cheap cisco POE switch in I can get 3 phones works very well, but due to the amount of energy needed for this cheap a cisco switch it will give only 3 phones power.

  The real problem here is plug into small business cisco SG300-10port POE managed switch.  I thought I could just connect the switch to the port configured above right out of the box and plug in phones without a problem.  When I plug the switch and start plugging in ShoreTel phones, they do not start coming in and upward and actually had a few phones upward but then finally there is no tone and also later, they appear on the screen as a service not available.

  I have to configure a trunk port on a port on the SG300 and the Cisco 6513 for this to work?  Also I will need to VLAN configuration manually on the SG300.  Looks like that when I just plugged it in to the above configured the port on the SG300 it automatically create the vlan 112.

  Any help would be appreciated

  Thank you

  Dave

  Double post.

  Go HERE.

• Ports SG300 &amp; AutoSmart for VLAN

  I have a few questions about the use of the ports VLAN & autosmart voice. I was running into a few problems getting it working 100% in my environment. Here in a few words, my network

  Switch to simple port SG300 52, 1-47 ports are configured unmarked VLAN110 (my PC LAN) and tag VLAN 140 permits (my voice VLAN) is 1 / the default VLAN on the switch and I have no assigned IP address and closed it.

  Made various reading I found this on the Forum:

  "The macro just get in the way most of the time. A default state on the switch a user will set the id of the vlan voice with orders

  (config) #voice vlan id 100

  * This will create the vlan 100

  VLAN, VoIP? * You can use to change your defaults for dscp and cos a long with all the other settings.

  State of vlan (config) enabled automatic #voice

  (config) #interface rank fa1-24

  (config-if-range) #switchport trunk vlan 101 native

  trunk (config-if-range) #switchport allowed vlan add 100

  * This function will define the vlan native on the trunk to 101 for the data port and vlan tagged will be 101 for the voice.

  CDP is enabled automatically and must learn the features of the phone and get on the phone to the vlan 101 on this port. »

  It worked well for my except in the case where I would have a phone plugged into the switch and a desktop computer hooked up to the back of the phone. I have to define the macro for IP + Desktop phone, then set it to VLAN for the 110 Office. If I don't he would stay to the VLAN ID of 1.  It's my only option? Can I change the default VLAN to 110 and just delete 1 VLAN? I was also running a random question with my laptop only where certain ports that I would link to (even if 1-47 are that all configured the same) would put just my laptop on VLAN 1, I'd watch the port autosmart and just, he would say "Default". I also disabled all the macro options IP Phone & IP Phone+ office. I really want to use this phone, I have no need of the autosmart ports do something else. Any suggestions or advice for this?

  Yes, by default the 'phone - PC' macro will set the default value of the Vlan untagged on the port to the Vlan 1.  You must simply change this macro and change the setting native_vlan to 110.  So when this macro runs Vlan untagged will be 110.

  No, do not change the default Vlan

  Good uncheck all types expect the phone phone & IP IP + Office