PC8024 interface with existing voice VLAN (100) on the switches HP 2910

We have added our first Dell PowerConnect 8024 switch to an existing network of switches HP 2910. We have only 2 VLANS configured: voice (100) and default (1). The switches HP all default ports VLAN are set to "no label" and all the ports on the voice VLAN are established 'labelled '.

I need to configure the PC8024 to co-exist with the existing network phones for Mitel can communicate. We are not familiar with the PC8024 switch, evaluate as a possible solution for improving our spine and DR subnet 1 GB to 10 GB. For the spine, we need the voice traffic to be handled properly, so we set up the work with the existing voice VLANS 8024.

What parameters of configuration of VLAN do we need on the PC8024 to co-exist with the existing network configuration for the (100) voice VLAN on HP switches?

Voice VLAN allows you to specify which VLANs, then you should be able to use the VLAN 1, but if you use VLAN 1 and 100, you could probably just create a VLAN 100 and not bother with the stuff of vlan voice. What type of port is the port you are trying to assign to tagged in? Access mode cannot do without label. If it was the general mode you can assign it labeled 100 and a PVID from 1 which would put traffic which is not marked on the vlan 1.

Tags: Dell Switches

Similar Questions

Need help to set up voice VLAN in SG300

Hello

I spent too much time on it now and need help. I'm trying to set up a voice switch VLAN on a SG300 - 28 p. I need to charge a phone Cisco 7965 connected to a port on SG300 - 28 p to use VLAN 100, and a workstation connected to the phone to use Cisco 7965 on VLAN 101 by SG300 - 28 p. In the common Cisco IOS switches, this task is configured as follows:

interface gi25

switchport mode access

switchport access vlan 101

switchport voice vlan 100

Trying to achieve this scenario with a Cisco SG300 switch turns into a nightmare. You will have to deal with a Dynamic of VLAN voice Auto Voice VLAN mode. Then, you must have a configured trigger and activated Automatic Smartport . I tried to do this in CLI nothing helps. Cisco 7965 receives an IP address of the access VLAN on Gi15 interface, which is 101 VLAN. I need to receive an address IP of the VLAN 100.

The current configuration under Gi15 interface is as follows:

interface gigabitethernet15

activate the storm control

broadcast storm control level kbit/s 10

Storm-control include multicast

port security throw trap 60

maximum port security by 10 points

port security mode max-addresses

spanning tree portfast

LLDP-med disable

switchport mode access

switchport access vlan 101

! next order is internal

macro auto smartport dynamic_type unknown $native_vlan 101 $voice_vlan 100

Now, I don't know how the macro auto smartport dynamic_type unknown $native_vlan 101 $voice_vlan 100 command in the config, and I do not know how to remove it.

When I try to enter the command macro auto smartport type ip_phone_desktop under Gi15 interface, I get the following error message:

The $voice_vlan macro setting is not configurable by the user

It seems that the auto attendant smartport macro ip_phone_desktop can not apply the setting $voice_vlan with a value of 100. In fact, I explicitly does not use this parameter to everything in the order of macro auto smartport type ip_phone_desktop ; However, the SG300 switch knows that the voice VLAN VLAN 100, and he's trying to use this VLAN ID as the value of the $voice_vlan parameter, the macro fails.

I tried statically configure the voice VLAN on the switch SG300 using the command id of the vlan 100 voice , but I couldn't get the ip_phone_desktop macro to configure interface Gi15 correctly. Then, I removed the command id of the vlan 100 voice and obtained SG300 to learn his voice VLAN ID of UC560 connected to the SG300 through a trunk port based on the port configuration (connected to SG300) for the trunk of the next UC560:

switchport trunk vlan 101 native

switchport mode trunk

switchport voice vlan 100

Cisco-switch macro description

This is the command switchport voice vlan 100 who announces to SG300 via CDP VLAN 100 is a voice VLAN. When I run the command show vlan local VoIP on the SG300, I get the following result:

VLAN ID - VPT DSCP Source MAC address Interface

1 5 46 default ---- ---

* 100 CDP e0:5f:b9:xx:yy:zz gi28

Thus, it is clear that the SG300 receives information from UC560 via CDP in port Gi28 VLAN 100 is the voice VLAN. However, I can not always apply the ip_phone_desktop macro to SG300 Gi15 interface.

Also, I tried to set up vState ofoithis vlan auto-déclenché as well as the commands in global configuration State vlan automatic voice activated mode. Or setting changes anything view voice VLAN announced at Cisco 7965 where Cisco 7965 continues to use VLAN101 (access the VLAN assigned to the interface Gi15).

Hello telecastle,

The Macro just get in the way most of the time. A default state on the switch a user will set the id of the vlan voice with orders

(config) #voice vlan id 100

* This will create the vlan 100

VLAN, VoIP? * You can use to change your defaults for dscp and cos a long with all the other settings.

State of vlan (config) enabled automatic #voice

(config) #interface rank fa1-24

(config-if-range) #switchport trunk vlan 101 native

trunk (config-if-range) #switchport allowed vlan add 100

* This function will define the vlan native on the trunk to 101 for the data port and vlan tagged will be 101 for the voice.

CDP is enabled automatically and should learn the features of the phone and get on the phone to the vlan 101 on this port.

CDP of the UC should automatically fill in the switch of the SG. You may need to upgrade the switch to the latest firmware however. Also make sure that the DHCP server for the voice if the CPU must be configured accordingly.

Let me know if this helps.

Cisco Small Business Support Center

Randy Manthey

CCNA, CCNA - security

Voice VLAN with SRW224G4P

Hi all

I tried to config a vlan voice in this switches for the last 3 hours and for me it's impossible... I know how to do it in a switch IOS but with this switches is a nightmare...

I have this topology

PC - telephone to IP - SW1 SRW224G4P - SWCORE SRW2024 - router 2921 CME

I have this config in my router,

interface GigabitEthernet0/0

no ip address

automatic duplex

automatic speed

!

interface GigabitEthernet0/0.1

LAN description

encapsulation dot1Q 1 native

IP 192.168.5.95 255.255.255.0

IP virtual-reassembly in

!

interface GigabitEthernet0/0.100

Description VLAN VoIP

encapsulation dot1Q 100

IP 192.168.251.1 255.255.255.0

IP virtual-reassembly in

!

SW1 created the VLAN 100 and activated as VLAN VOIP

The first 3 octes for the mac on my phone is inserted into the Table YES telephony

Belonging to a VLAN automatic voice is enabled in the port where the phone is attached.

The port connected to the SWCORE has the vlan configured as labeled 100.

SWCORE has created the VLAN 100 and activated as VLAN VOIP

The port connected to SW1 has the vlan configured as labeled 100.

The port connected to the router CME has the vlan configured as labeled 100.

If I have another config port in SWCORE with 100 VLAN Tag I can ping from FMC to this host.

Could be the problem, an error of spread vlan?

Could someone help me? I'm desperate...

Thank you in advance.

Hi David,

Thank you for the purchase of the switch.

. Like what, even riding a bike, the switch is actually very easy to set up, if you practice on it...

You mentioned that you use the 'phone YES picture' I assume you have a SF300 - 24 p or p/n command SRW224G4P-K9-NA. Please be specific with the models of switches you use.

Using the old SRW series or refreshed in the kernel SRWxxx-K9 (300 series) switch?

First of all, make sure that you are using version 1.1.0.73 of the switch firmware. This change now or check that 1.1.0.73 is the active image on the switch.

The switch has two areas to store the firmware images. It stores the new firmware in the area of the image unused. The administration for the firmware update Guide and select new firmware for the next reboot.

CDP is enabled on the switch when using the new software, did not exist with older firmware, where my insistence to upgrade the firmware.

( Personally I would prefer that you have a role of catalyst for switching to your CME ISRG2 application, for purposes of support tech.) But this is the land of freedom..)

I found the following when I added my SG300 - 28 p to a conscious UC500 of VLAN.

The UC500 was vlan100 of advertising as a vlan voice, configured by Cisco Configuration Assistant, you could try CCP on your ISR.

I got an IP phone that is plugged into the port of switch in the G7 and uplink to my UC500 via the Gig27 port.

What follows in blue is a screenshot of my 300 series switch CLI interface.

You will notice that the switch already filled both VLAN and port information, the only command that I added was "don't activate any complexity of passwords" and some usernames, including free from the screenshot below.

the configured basically switch itself.

-See the establishment of the system-

Description of the system: 28 ports Gigabit PoE managed switch

System of the time (days, hours: min: sec): 00, 00:12:04

Contact system:

Name of the system: switch4cf17c

System location:

System MAC Address: d0:d0:fd:4 c: f1:7 c

System object ID: 1.3.6.1.4.1.9.6.1.83.28.2

Fans Status: OK

-See the version-

SW version 1.1.0.73 (date, June 19, 2011 time 18:10:49)

Start the version 1.0.0.4 (April 8, 2010 time 16:37:57)

HW version V01

Location of activity IP gateway Type.

----------------------- ----------------------- --------

192.168.10.1 active dhcp

IP address I / F Type of status

------------------- --------- ----------- -----------

192.168.10.17/24 vlan 1 DHCP valid

-show ipv6 interface-

IPv6 is disabled on all interfaces

-show running-config-

interface gigabitethernet7

Storm-control broadcast level 10

output

interface gigabitethernet7

Storm-control include multicast

output

interface gi27

point to point spanning tree-type of link

output

database of VLAN

VLAN 100

output

Add a voice vlan Yes-table 0001e3 Siemens_AG_phone___

Add a voice vlan Yes-table 00036 b Cisco_phone___

Add a voice vlan Yes-table 00096e Avaya___

Add a voice vlan Yes-table 000fe2 H3C_Aolynk___

Add a voice vlan Yes-table 0060 b 9 Philips_and_NEC_AG_phone

Add a voice vlan Yes-table 00d01e Pingtel_phone___

VLAN voice Yes-table add Polycom/Veritel_phone___ 00e075

Add a voice vlan Yes-table 00e0bb 3Com_phone___

hostname switch4cf17c

No complexity of passwords allow

No server snmp Server

interface gigabitethernet7

macro description ip_phone_desktop

output

interface gigabitethernet27

description of the macro "pass | valeur_log | switch ".

output

interface gigabitethernet7

! next order is internal.

macro auto smartport dynamic_type ip_phone_desktop

switchport trunk allowed vlan add 100

output

interface gigabitethernet27

! next order is internal.

switch dynamic_type macro auto smartport

switchport trunk allowed vlan add 100

output

switch4cf17c #sh cdp nei

Ability code: R - router, T - bridge Trans, B - road Source bridge

S switch, H - host, I - IGMP, r - Repeater, P - VoIP phone

M - managed remote-device, C - CAST phone Port,

W - two port MAC relay

Device ID Local time from Port platform capacity ID Adv

The interface direct worm.

----------------- ----------- ---- ------- ---------- ------------ -----------

SEP503De50F133A gi7 2 158 H P CISCO IP eth0

Phone

SPA525G2

68bdab0fdcfd gi27 2 169 S I Cisco SG gi9

300 10 P

(PID:SRW2008P - K9) - VOD

switch4cf17c #sh vlan

VLAN name Ports type permission

---- ----------------- --------------------------- ------------ -------------

1 1 article gi1-28, required to Po1 - 8 by default

100 100 gi7, required permanent gi27

Automatically numbers which ports need to be listed in VLAN 100.

I did not switch it was connected to VLAN100. I don't have add vlan100 to the database for VLAN.

Get the ISR router to announce VLAN100 as a vlan voice.

Best regards, Dave

Question SG500 auto voice VLAN VLAN native

I have install SG300 and SG500 switches and using the function of vlan automatic voice by simply changing vlan 100 and using voice of vlan 1 for data and the default value. I normally put the L3 switch and make a porteach access for my IP PBX (vlan 100) and the other to connect to the existing data network (vlan 1). Then I do a static route in default gateway customers to route to vlan 100 and everything works well for most facilities.

On my last install, I decided to try to change the vlan 1 default vlan 10 and go with 10 for data and 100 for the voice. The problem that I ran was that the auto generated on my phone switchports config still serve of vlan 1 vlan native. I am trying to find a way to always use auto vlan and get the vlan native desired without having to make manual configuration changes.

Would this be possible?

Thanks in advance.

Hi Brandon, you must edit the macro of vlan native 1 to vlan 10.

Check out this topic How change the macro

https://supportforums.Cisco.com/thread/2177613

-Tom
Please mark replied messages useful

SG200 - 50 p, SG300 - 28 p phone YES Voice VLAN

Hey guys,.

I'm having a problem with the YES voice of VLANS on SG200 - 50 p, SG300 - 28 p, layer 2 Mode. Firmware 1.3.7.18.

Enabled on a port all the ports PVID unlabeled said no marked traffic is blocked.

Example:

Data VLAN 10 - 192.168.10.0/24

Voice VLAN 100 - 192.168.100.0/24

Configuration of Vlan voice and YES added and enabled on ports.

All Ports configured as trunk Type.

Example 1:

Members Table shows that:

Port 1 - 10UP

2 port - 10UP

YES disabled: 2 laptops connected to ports 1, 2, traffic passes.

YES Enabled: 2 laptops connected to ports 1, 2, traffic blocked on VLAN10.

Example 2:

1 - 10UP, 100 tons of port

2 port - 10UP

Port 3 - 10UP

YES Enabled: 2 laptops connected to the ports 2,3, blocked traffic on VLAN10.

1 phone connected to channel 1, the phone connects.

So it's using, but for some reason any the vlan untagged on that port is blocked when the YES is enabled.

I have installation this scenario on many switches cisco small business before and it works very well, so I wonder is this a firmware issue? or am I just being stupid and something wrong?

Thanks for any help you can provide! :)

Hi Vladimir,.

It's something about Cisco still working. You are more than welcome to open the ticket with us and contribute actively. At this point, the only solution is to sue 1.3.5 firmware which does not show this problem.

http://www.Cisco.com/c/en/us/support/Web/TSD-Cisco-small-business-suppor...

Kind regards

Aleksandra

A module C - DAQ exists which will interface with standard RV - C?

Module C - DAQ exists that if interface with standard RV - C (vehicles recreational CAN)? RV - C seems to be a variant of J1939 according to Wikipedia.

I would use 9861 OR or NI 9862. I'm new on CAN protocol and evaluate some assistance.

I've never used RV - can, but according to Wikipedia, the rate is 250Kbaud, so you'll want high speed CAN peripheral, 9862, you can set baud rate on init of the material. After installing XNet and cDAQ software, you have a max bus monitor and several examples in the example Finder to read and write raw images. After that, you'll want to read on the standard to understand how to format and analyze the data.

Also if you have any questions, you can post on the Sub-forum Auto , they can probably answer more specific questions.

problem with dhcp Cisco sg200 voice vlan

I have cisco sg200 50 p connected to the switch cisco 3750. I just wanted to separate voice (vlan2) and data (vlan1) VLAN. I created vlan 2 as my voice VLAN and separate dhcp server for vlan 2 to give IPS for phones. However the phone ip connected to my voice vlan (vlan 2) does not receive the ip address of my dhcp server vlan 2.

the dhcp server is connected to a switch with an access port (vlan2-voice) 3750

two switches are connected through the trunk ports and allowed vlan 1 & 2

IP phone is connected to sg200 via the access port (vlan 2).

Note: there is a pc connected to the ip phone

I'm really grateful if someone can help me with this problem

Hi Ruchiran,

To cover the base, ensure that VLAN 2 is added to the database VLAN on the 3750. Simple by using the command "show vlan id 2", if it is not found, you must first create the VLAN 2 on the 3750.

Second, if you connect the same IP phone directly to the 3750 on an access port, vlan 2 unidentified, is the phone receives IP address as you hope?

Then, on the trunk of 3750 connection to the SX200. Building the trunk when using a command like "switchport trunk allowed vlan remove 1-4094," then build the trunk more precisely with the VLAN ' trunk switchport allowed vlan add 2 "who will score 2 VLAN port." "

On the SG200 switch, must be defined the trunk and VLAN Tag 2 on the port to connect to 3750 then the connection to the phone port should be 2 VLANS not identified as access port.

SG300 voice vlan problem with UC520

Salvation of the Forumers

My problem statement:

-Secretary referred to topology.png, this is how my network like structure look

-the IP phone after startup can not connect, so it cannot download the XML of UC520 configuration file. problem switching suspects.

-my configuration illustrated in topology.png and my config show vlan as the voice setting.png voice vlan

-My requirement is switch SG300 unique switchport to carry data VLANs and vlan voice.

-What is the mode of connection for voice siwth VLAN an IP phone + data must be set up? is it switchport voice vlan vvid switchport voice vlan dot1p, switchport voice vlan unidentified or vlan switchport voice no further action over requirement?

Thank you

Noel

Christmas morning,

Sorry for the late reply, things have been very hectic in here lately

1. Why use trunk? the UC520 don't have voice vlan (vlan 20)

Do you mean that data THAT VLAN is handled by another device? Again I would like to leave as a trunk in order to manage the CPU through the data VLAN. (Except for security or other reasons you would choose differently of course)

2. the UC520 got CUE (voicemail), how should I design the uplink service for the main switch module?

Nothing in particular needs to be done for this, CUE is processed and routed inside the UC520, the vlan (default ID = 90) CUE is used if you have another LANDMARK in the network

1. I guess I did: swithcport the tag vlan vlan unlabelled 20, 10. is it ok for this setting?

If the Vlan on the switch and the UC520 voice has been defined as VLAN 20 (default value = VLAN 100) it's perfect. Check if the CPU and the switch, the voice VLAN ID is set to 20.

1 so if I have just the phone to vlan 20 (vlan voice), create the policy of network LLDP?

If you are ready to configure the VLANS manually on the phone, you don't need politics LLDP, thats right.

Politics LLDP is used to having phones automatically choose the VLAN you set, so you do not need to set it manually.

I hope that answers your questions?

Best regards

Nico glacier

Senior Network Engineer - CCNA

Reference Dell 6200 Voice Vlan

Hello

Could someone show the config complete for the vlan voice with a VLAN for data on the same port it please?

I currently have all the switchports in one vlan 10 normal data, the phone system and phones are also in this vlan. However, I now want to put phones on one vlan separate voice sharing the same port.

My current Config is:

Configure

database of VLAN

VLAN 10

interface vlan 10

name of 'NETWORK '.

Routing

IP 192.168.10.1 255.255.255.0

interface ethernet 1/g1

spanning tree portfast

switchport access vlan 10

output

In my understanding, I have to do the following:

Configure

database of VLAN

VLAN 20

interface vlan 20

name of the "voice."

Routing

address 192.168.20.1 255.255.255.0

interface ethernet1/g1

spanning tree portfast

switchport mode general

pvid switchport General 10

VLAN 20 voices

output

Thanks for any help you can give, it's urgent fairy we should have had this work tonight :(

Here is an example of a configuration of VLAN basic votes for a port to have a phone and workstation on this subject, with each device traffic, separated from each other.

Example:

VLAN 100 is set up for voice *.

VLAN 10 is set up for data. ****

Console (config) # vlan VoIP

Console (config) # interface ethernet 1/g20-1/g24

Mode console # switchport general

Console # switchport General allowed vlan add 100 tag

Console # switchport General allowed vlan add 10 untagged

Console # pvid general switchport 10

Console # switchport general allowed vlan remove 1

Console # vlan 100 VoIP

Console # end

There is also this white paper with some good info in there.

www.Dell.com/.../pwcnt_voice_VLAN_support.pdf

Hope this helps some.

See you soon

Voice VLAN help please

My client has 2 SG300 - 52p and 5 SG300 - 28 p. We have installed a VoIP telephony system earlier this year. At the time of installation, we placed the phone on the native VLAN 1 System. Now, they want to pass the phone system to a new VLAN, because their class C subnet is running out of addresses. DHCP is managed by their Active Directory and their router/firewall is a box to sort out. The SG300 switches have a basic configuration only.

To move the phone system to a new VLAN, I created 20 VLAN on each switch. I then turned on VLAN auto voice. I have all the ports on each switch setting on the trunk. Computers are plugged into the back of the phone. I then created a virtual interface in the box to unravel for VLAN 20. Box unravel also manages DHCP to the new VIRTUAL LAN. Active Directory is always manage DHCP for VLANS native.

I ping from each switch to the bridge of the new VLAN. Since each computer I can ping the gateway and on the new LAN VIRTUAL phone system. However, phones will not seize an address on the VIRTUAL LAN and when they have the static value, they cannot communicate with other devices on the VIRTUAL LAN.

Any help would be much appreciated. I don't know what I'm on.

Here is an example of part of a switch configuration to work with Zultys phones where voice VLAN is 100 and data VLAN 10:

database of VLAN
VLAN 10,20,100
output
ID of the vlan 100 voices

interface fastethernet1
Description "RCP and voice."
switchport trunk allowed vlan add 100
trunk switchport vlan 10 native
!
interface fastethernet2
Description "RCP and voice."
switchport trunk allowed vlan add 100
trunk switchport vlan 10 native

In your case, you need a trunk port with 20 VLAN Tag on your firewall (or an access port to a separate physical port on VLAN 20. The default gateway served on the phone (or put statically) should be the interface on intellectual property. Then, you can also allow routing inter - vlan for admin access or MXIE if you use.

One thing to note on Zultys is by default I think the device profile disables LLDP, but on phones, it is enabled out of the box. For the first time that a phone downloads its config from the Zultys it can turn of LLDP unless you have checked the box to keep it on.

VLANS with Cisco ASA 5505 and non-Cisco switch

I have an ASA5505 and a switch Netgear GSM7224 L2 that I try to use together. I can't grasp how VLANs (or at least how they should be put in place). When configuring my VLAN on the ASA5505 it seems simple enough, but then on my switch, I thought I'd create just the same VLAN numbers that I used on the SAA and then add the ports that I wanted to use for each VLAN.

Currently on my ASA, I have the following VLAN configured...

outside - vlan11 - Port 0/0

inside - vlan1 - Port 0/1

dmz_ftp - vlan21 - Port 0/2

Port of Corp - vlan31 - 0/3

I need to do the same thing on my switch as well... On my way, I'm a little confused as to how I need to configure the VLAN. Below is the screenshot of web GUI...

Note: Normally you can now change the VLAN ID (red), but in this case the default vlan (vlan id 1) may not be changed or deleted, you can does not change its settings.

Tagged (green), Untagged (purple) and Autodetect (yellow) you must select at least 1. I'm not sure how to in one place to tell my inner vlan (vlan1).

I want VLAN1 ports 1-8 on my Netgear switch used alone to talk to interface/0/1 on the ASA5505 port. I don't want to NOT port 9-24 able to talk to ports 1-8 on the Netgear switch ports OR 0/0, 0/2 - 0 / 7 on the Cisco ASA 5505.

So, how can I configure my inner Vlan1 on ports 1-8 on the switch? Do mark, UNTAG, autodetect them? What about tours? I've been a bit the impression that I would set up my VLAN on both devices, then trunk port 1 and dedicate this port on both devices to nothing other than the sheath and the security of vlan would then take the packages where they need to go. Is this the wrong logic?

Hi Arvo,

If the port of the ASA is just part of a single VLAN (i.e. e0/0 single door 11 VLAN), this is called an access port. If the port of the ASA had to carry several VLANs, it would constitute a Trunk port.

To access ports (VLAN unique), you must set the switch corresponding to be unidentified for port this VLAN individual. If you decide to configure a trunk port, then the port of the switch must be set for labelling for each of VLAN who win the trunk.

For example, ASA I have:
```
interface Ethernet0/1
switchport access vlan 20
!
interface Vlan20
nameif inside
security-level 100
ip address 192.168.100.254 255.255.255.0
```
With the above configuration, the configuration of the switch would look like this (assuming the e0/1 port of the SAA is connected to 0/1 on the switch):
```
VLAN 20 - 0/1 = untagged
```
If instead you use a trunk port, the config would look like this:
```
interface Ethernet0/0
switchport trunk allowed vlan 10,20
switchport mode trunk
!
interface Vlan10
nameif outside
security-level 0
ip address dhcp setroute
!
interface Vlan20
nameif inside
security-level 100
ip address 192.168.100.254 255.255.255.0
```
Assuming that the ASA e0/0 port is connected to 0/1 on the switch):
```
VLAN 10 - 0/1 = tagged
VLAN 20 - 0/1 = tagged
```
Hope that helps.

-Mike

LabVIEW interface with multiple blocks of Festo module

I am trying to connect with a block of Festo, but I can't. Here are the details:

I'm under Labview 2012 SP1 with IndComm-DeviceNet 2.2 pilot on a 64-bit Windows OS. I installed a PCI 8532 card NOR. I see the map to the MAX.

The block of Festo is built with the following Modules: CPX_FB11 (communications module), 4 analog input Modules, 1 Digital module, 2 digital modules followed by 32 Festo valves. (Image below)

Using DeviceNet PXIPCI Basics.lvproj I did the following:

In the project, right-click on desktop > New > targets and devices > existing target or device, discover an existing target or device...

Expand the node of DeviceNet Master Interface, DeviceNet1 chosen and added to the project.

A click on the newly added DeviceNet/device target > New > targets and devices...

Expanded the Festo Block "CPX_FB11" selected DeviceNet slave device and added to the project.

Initially, I received an error card technique 'EDS file no assigned' I solved this by following the direction listed here.

However, I'm unable to "see" anything other than the CPX_FB11 LabView. The tree view of the devices lists not analog, Digital e / s or valves. I can't operate the Valves and IOs digital or analog. When I run the entire project VI they then expire.

Any help would be appreciated.

Thank you

Tennessee Paul

Hi Jesse,.

I'm not entirely sure what the specific problem was. I kept getting strange behavior. Errors in LabView and on my camera from Festo. The EDS files change. So, I did as any natural born THERE would be worker, I rebooted.

Here are the steps I used to get this project going. In doing so, I found that to set up a DeviceNet device in LV2012SP1, no need to manually enter the data in file EDS. There is a tool to load files EDS. It dealt with issues I had in the previous Forum posts: here about loading files EDS in LabView and here regarding setting up a DeviceNet network.

Environment: Windows 7, 64-bit processor. IndComm 2.2 pilot. LabVIEW 2012 SP1

Starting with the example LabView project: "Devicenet PXIPCI Basic.lvproj.

Add a DeviceNet master to a LabView project
1. The project: right-click on my computer
2. Select the option "discover existing devices.
3. Select the discovered device.
4. Click 'OK' (Note: in this case, my master is a card PCI of NOR-8532)
Add a DeviceNet slave device to a LabView project
1. Right-click on the master device newly added in the project tree
2. Select 'discover existing devices.
3. Select the discovered device.
4. Click OK. (Note: in this case my slave is a block of Festo CPX-FB11.)
Load an EDS file to the slave device
1. Right-click on the slave device
2. Select "Sheet"... »
3. Click on add files...
4. Navigate to the location of the EDS file.
5. Select the file.
6. Click OK.
7. In the left pane, expand the data sheet newly added up to reach the node displays the version.
8. Select the version.
9. Click OK.
Check the device and file EDS
1. Right-click on the slave device
1. Select utilities
2. Select the Panel of Test online
Select the option 'Device status' in the field of category on the left.

On the right, select the slave device, you want to check.

Click on "check the device".

Read the errors/warnings or lack thereof.

In my case I had errors in my EDS file. Basically the slave device was not defined for the correct number of bytes of input/output in the EDS, i.e. a wrong configuration file. To fix this I had to change the EDS file.

Edit the file EDS

To change the EDS file, I used EZ-EDS , which is a freeware, devicenet specific EDS editor of ODVA.

I did my corrections and saved my file EDS. (After having saved my original, of course).

Remove the installed Labview EDS file

Navigate to the following location: C:\ProgramData\National Instruments\NI-IndComm for DeviceNet\Datasheet

Remove the sheet (Note: there is more that one datasheet added manually.) Additional EDS files come with the IndComm driver. Find the EDS file for the specific device that you want to replace and delete).

I restarted LabView.

I went through the steps above again and loaded my new EDS file.

I saved the project and came out of LabView.

I rebooted the computer and the slave device.

I restarted the project and launched a VI.

I was able to communicate with the device. That is something that I had not been able to do before. And, in doing so, I discovered how the device speak and why were not each module. (I have a standard for my block devices EDS file, as it appears that LabVIEW is not capable of a modular system that requires an EDS file for each module. I could be wrong on that last part though, as there may be a setting on my real device. But it is unecssary in my project. So I do not consider this further.) Because I was using a standard file of the EDS, only a single slave device showed, and so the data for each module are in the stream of bytes returned to the DeviceNet network. Addressing each module is a question of analysis the bits and the bytes appropriate.

Thank you

Tennessee Paul

Having trouble getting the voice VLAN on the switch X1052P to work at all

Can someone help me understand how to set up the voice VLAN X1052P? I spent several hours trying to get this working and it does not work. I spent about 4 hours on the phone with a Dell technician that night and he couldn't get it to work and finally gave up. He told me that I had to spend my warranty to ProSupport because he did not know how to solve the problem. What group of *. It's a simple configuration of VLAN. What must be so picky about? In any case...

Setting up the VIRTUAL LAN must be fairly simple, but apparently on this switch is not. The user guide page 406 is not very useful except explaining what the different options. I must admit I am not an expert VLAN so I dunno I've misconfigured something. But remember, Dell technology could not operate either.

Here's my situation... I have VoIP phones on my network connected to a network wall jack. Connected to phones are my computers of users. The computer of the user and its respective VoIP phone, both share the same data cable. Before replacing Cisco managed Internet service provider spend all it worked well. The problem is that they had direct access to our network so I removed the switch and installed the X1052P in its place. I talked to the ISP to let them know what I'm doing and they said everything I had to do was setup VLAN ID: 15 for the voice VLAN because this is the VLAN ID that the router uses to route telephone traffic. Router PSI is also the server DHCP VLAN 15 and issues IP for phones using 172.27.0.0/24 with a DHCP 172.27.0.50 range - 150.

I tried to configure the switch using parameters of VLAN static and settings VLAN voice and neither one also seems to do what I want it to do.

Network administration > VLAN > VLAN static

Network administration > VLAN > Voice VLAN

I activated the profile 'phone' on ports I want to added to the voice VLAN and it does not work. Moreover, 47 the switch port is connected directly to the ISP router and is configured as a trunk with the default port VLAN 1 unidentified and tag VLAN 15. For other ports I tried the general implementation, access and trunk of the parameters on each port to see if I could get something going and still nothing happens. When I set up the ports as General ports VLAN, I made adding VLAN VLAN 1 and VLAN 15 as a VLAN tagged not marked. It still does not.

This is the short story from where I am now. Any help is greatly appreciated.

FYI, as a follow up I finally solved the problem. I hope this information helps someone else that can encounter the same problem.

After buying the ProSupport warranty upgrade ($121 out-of-Pocket mind you) and addressing a total of 4 technicians ProSupport expert technician a 3rd another level (only available via chat message between one of the ProSupport phone technicians and the 3rd Tier expert tech - i.e. I couldn't talk or chat with this person me) the consensus was that the material must be bad. When I bought the X1052P I bought two of them, so the best way to know if it was a bad switch was simply configure the other switch and see if the behavior occurs on this one, too. Well, this switch also restarted each time I assigned the profile 'phone' to more than 13 or 14 ports in the switch. It seems that it was not a hardware problem after all.

I went back to the switch original and tried new things hoping that I could fall on a solution and it turns out that the solution was NOT to use the voice VLAN on the switch. It does not work!

SOLUTION: I set the VLAN ID: 15 manually and no has not assigned any phone profiles to one of the ports. This is how I solved the problem.

So he has bad software on the switch. I tried to see if there are updates of the firmware on the Dell support site, but there is none. Configure manually the phone VLAN was the solution. What a freaking nightmare which turned out to be. Maybe someone in Dell could note this problem and test in-house. And, if you want to compensate me for the 20 + hours I spent working on this problem, which has be great, too.

There is no command 'Switchport Voice Vlan"on SF300 - 24 p!

Hello everyone

I am in an urgent problem: S

I have a small business SF300 - 24 p

I created two vlans one data and one voice

but I have not assigned to ports and I do not know how, because there is no command ' switchport voice vlan "under the interface!

Here are the configurations

BTW the switchport mode is always trunk as it is by default

Thanks in advance

switch0a1172 #.

switch0a1172 #.

switch0a1172 #sho run

config-file-header

switch0a1172

v1.2.9.44 / R750_NIK_1_2_584_002

CLI v1.0

SSD of encrypted file indicator

@

SSD-control-start

config of SSD

control of password file unrestricted SSD

no control of the integrity of the file ssd

SSD-control-end cb0a3fdb1f3a1af4e4430033719968c0

!

database of VLAN

VLAN 13.20

output

ID of the vlan 20 voices

Add a voice vlan Yes-table 0001e3 Siemens_AG_phone___

Add a voice vlan Yes-table 00036 b Cisco_phone___

Add a voice vlan Yes-table 00096e Avaya___

Add a voice vlan Yes-table 000fe2 H3C_Aolynk___

Add a voice vlan Yes-table 0060 b 9 Philips_and_NEC_AG_phone

Add a voice vlan Yes-table 00d01e Pingtel_phone___

VLAN voice Yes-table add Polycom/Veritel_phone___ 00e075

Add a voice vlan Yes-table 00e0bb 3Com_phone___

hostname switch0a1172

username, encrypted password cisco c8e383b1dd7be99f878a387d87766e875404e0b3 priv

LG 15

The telnet server IP

!

interface vlan 13

name "VLAN13".

!

interface vlan 20

VOICE name

!

switch0a1172 #.

It does it automatically via the port smart auto based on external trigger default. Devices to enable CDP and LLDP are supported.

-Tom
Please mark replied messages useful

Activation of the NAC HA puts several hosts and ASA with processor clocked at 100%

I installed a NAC Manager and a NAC server in OOB without any problems, but when I configured the AP (high availability) with another server, my ASA and several guests in my network started work ant 100% of the cpu.

I tried to configure each interface of the NAC on a single DMZ and the problem stops there.

-That someone had this problem (NAC version 4.7)

TKX

Miguel Amaral

Hello Miguel.

When I started a NAC InBand HA solution I had a similar problem that I solved the heart rate HA configuration to use ETH0 just instead use ETH0 and ETH1.

Best regards

Luciano Carvalho

PC8024 interface with existing voice VLAN (100) on the switches HP 2910

Similar Questions

Maybe you are looking for