ThinkPad T510 (part # 4313CTO) accidentally connected to a power adapter 90W

Similar Questions

• My Satellite goes into battery mode despite being connected to the power adapter

  Y at - there anyone out there who can help me, please!

  I bought a Satellite a couple of years ago which worked well for a while - however, it has started to overheat a lot and kept stop without reason. After many searches on the net, I discovered that the fans were very likely blocked with dust? After you clean the laptop worked like a dream and as a Bunny happy I was!

  However, now a new problem has been its ugly reappearance - for some weird reason the laptop suddenly, without warning, past in dominant mode of battery despite being connected to the power adapter? He refuses to "acknowledge" that the adapter is plugged drains the battery quickly and then stops?

  I tried once more looking for an answer and it seems that I am not alone in suffering from this problem? I read that it is perhaps a bad connection between the adapter and the motherboard, but it would be expensive to fix? Others have said to try a new adapter, but I tried from another laptop and it still happens? I hesitate to implement local repair because sometimes, this problem may occur after half an hour and other times, that won't happen for hours and hours and it is difficult to explain the problem?

  There seems to be no rhyme or reason, but to crazy me on a regular basis!

  HI Deb,

  It is a common problem and can have several causes. The most common are a common defective soldering on the motherboard (where the socket is attached) and it can also be caused by a bad connection between the AC plug (at the end of the cable) and the socket on the laptop.

  Unfortunately, the standard response from most repairers is just to replace the motherboard, probably because it's faster for them and produced more revenue that comes to fix the connection.

  I solved this problem on my SA30 by pinching the cable ca to the back of my laptop in order to prevent any movement or tension on the connector. Unfortunately this will not help if the socket is already damaged, but it can reduce the incidence of the problem to occur.

  Kind regards

• Spectrum for computer laptop 13-v051na: connect more capacity power adapter Message

  After starting, I get the following message. "For maximum performance, connect a higher capacity Power Adapter.

  The power adapter I use is provided in the box with the notebook. So I'm at a loss on what to do and do not understand the impact with an adapter in addition low capacity.

  AFAIK, the ability for the laptop power adapters are not in the HP store.

  Details of the laptop;

  Spectrum of HP for computer laptop 13-v051na, part number; F6P95EA #ABU

  (Note that this laptop is a variant of PCWorld/Dixons cell phone spectrum HP Ref. 13 - v001na F4W33EA #ABU)

  Details of the charger supplied with the notebook; (markings on the charger)

  Power supply for charger USB - C;

  Model; TPN-CA02

  HP part No.; 848067 002

  HP Spare; 848293 850

  Entry; AC 100-240V 1. 4A

  Exit;

  5V 2A DC

  12V 3A

  15V 3A

  45W max

  Additional information about the message;

  Message; "For maximum performance, connect a higher capacity Power Adapter.

  In the taskbar, the icon indicates that the message is from HP system information.

  Application properties (found via the Task Manager) HP system information are;

  • File; USBCMSG.exe
  • Location; C:\Program Files (x 86) \HP\HP event system
  • Version of the file; 1.4.14.0
  • Version of the product; 1.4.14.0
  • Date of change; 20/06/2016
  • Original file name; SysInfo.exe

  Good news is that there is a difficulty.

  I was given further guidance to Support cat HP, including a link to the page software and downloads.  This shows a new BIOS Softpaq, which has not been suggested by HP Support Assistant. Details of the update of the BIOS are;

  HP Notebook System BIOS Update (Intel processors) F.26 Rev.A 15.4 MB 24 August 2016

  File name: sp77130.exe
  Communicate details
  Exit the: 12 August 2016
  Version F.26 Rev.A

  I have applied this update of the BIOS and the wrong power adapter warning message no longer appears.

  Problem solved. Thank you HP.

• Satellite M40x-189 heats up when it is connected to the power adapter

  Hey,.

  I have a Toshiba Satellite M40x-189, which is about 18 months old. Recently, I had too replace the battery, but now it seems that my adapter had fried itself. He refuses now too charge my cell phone for more than a few minutes and the part of the adapter that goes into the laptop becomes ridiculously hot even after a few minutes.

  I can't find where too much to buy a new adapter, I get results, but adapters look totally different, can anyone tell me if Toshiba has changed the cards and where too find a power adapter.

  This may help - adapter PA1650 - T 02:100 - 240V AC 50-60 Hz 65W / 3 pins with 19V DC output.

  Also, I find that on the occasions, my laptop just cut. In the middle of everything what I do, and the laptop itself would become so hot, it can't be touched for a few minutes, interestingly, this only happens when the laptop is charging. This problem is not related too my adapter problem, because its been happening for a good month now.

  Thank you, in advance.

  Post edited by: Danny90

  Hello

  I saw your first thread on the power adapter and that other users already suggested the power adaptor can be ordered from the maintainer authorized Toshiba in your country!
  If you n t know how to find the service provider allowed in your country, please take a look on the homepage of European support of Toshiba. You will find a link to the database ASP.

  As you have already said the laptop automatically stops downs have nothing to do with the AC adapter.
  I agree with you for me, it looks like overheating!
  Usually, this happens if fans and cooling modules cannot run with maximum efficiency.
  Dust may prevent the complete rotating fan!

  I recommend to use the vacuum against the bars of cooling hose to clean the fans!
  It should help!
  But please be careful.

• Satellite A200 - STARTING problems, freezes on the connection of the power adapter

  My 3 YO A200 (PSAF3A-08202D has developed a problem with starting.
  I can start on battery power with WINDOWS VISTA BUSINESS (after 10 attempts, but freezes immediately when the power adapter is plugged in.)
  Display sometimes boots wide-screen, but mostly freezes before windows welcome.

  When running, the battery produces about 1 to 2 hours before a complete evacuation.
  When executing a battery, computer freezes when I plug Charger AC/DC immediately and going with my A100 charger as an alternative.

  Initial problem was a faulty hard drive and super hot air flow due to fluff the cooling block fan.
  Tech replaced original 120G HDD with 500 G and reloaded at the factory. works well for 3 months, then started with the same problems so conclude original disk HARD was just a secondary issue.

  So maybe fixed I overheated components on the motherboard. Reset of data cards initially fixed a problem starting but is gradually degraded.

  Reading through the forums seems that there is a huge amount of these laptops with similar issues. Is this a design flaw, like my other Satellite A100 is solid as a rock. All forums, which suggests resetting the cpu is running slow or be disconnected seem to be temporary repairs. Boot in safe mode and reset the default settings have no effect.

  A suggestion that a capacitor is at fault seems to be the fix is valid but which involves specialized tools is not available locally. Local agent of Harvey Norman for Toshiba are best part of unnecessary because they can send in Australia from Toshiba. Machine has been close to $2000 and is now worth Zip.

  I am unable to do anything with this machine, as all the ways of upgrading or resetting calls for AC power available and running.

  I'm about to do radical things and hope that this forum can enlighten us.

  Hi Mickaël

  You might be right. It seems that the motherboard is affected.
  Don't know why but higher temperature can still affect the internal parts.
  The temperature may increase if cooling fans n t working correctly. For example dust or debris leads to a higher temperature because cooling air cannot circulate properly.

  I have to clean my laptop's cooling grilles from time to time using a jet of compressed air. This allows to keep the temperature at the lower level.
  Of course the internal temperature is not always a reason for portable computers hardware malfunction equipment can begin to malfunction as always in an other products too: TVs, cars, game consoles

  I bought an extended warranty for my laptop, also for my LCD TV mercy always if a high-end product begin to malfunction and in the case of a warranty claim, the fault can be fixed free of charge.

• How to control the battery charge when you are connected to the power adapter?

  I post here because I want to know if there is any software option that I can use to control on my load while I use the charger and the dough.

  EXPLAIN

  You know in IBM ThinkPad there are some utilities can help you master the power to CUT the battery charge and keep on the power of the charger and the battery is always on standby if it is OFF the bettery then work and never lose anydata

  I want to control the load while I'm working with battery and charger at the same time.

  I hope that claire ;)

  Hello

  It of not possible to control the battery charge using any software.
  The battery will begin to charge if the adapter has been connected to the laptop and it will stop the charge process after the adapter has been disconnected or if the battery is full.

  See you soon

• Satellite U500: Volume + button glue IT when it is connected to the power adapter

  I have a problem with the touch buttons on my U500. I have already returned the first laptop that I bought for the Exchange.

  The question is this:
  When the power cord is connected (without worrying if connected to the wall) the "Volume +" button will stick THERE.
  The volume will continue to rise, it cannot be muted or turned down as the + keeps repeating.
  Without the power cable inserted the works of buttons as expected (normally).

  I made the new installation of recovery discs - do not set (under Vista)
  Then another new installation Win7 upgrade and this new PC is having the same problem.
  At first, I thought a hardware fault (the new PC worked fine for awhile).
  But now the second PC has the same symptoms I suspect a software/driver problem.

  I've seen suggestions for similar questions to:
  Re-install "Toshiba common Modules" but I can't find it on the support site for U500 in Australia.

  Any help would be greatly appreciated. Thanks to you all.

  What version of BIOS is installed?

  Try to update the BIOS.

• Connect to the power adapter 65W

  How to connect to the adapter sector 65? / does not charge my laptop it says that I need to conncet to the AC adapter 65W.

  It simply means that you need to use a charger work, approved, the manufacturer of your laptop.  If you get this message with the adapter plugged into the wall and the laptop, this might mean it has failed and must be replaced.

  "BabyGirl22" wrote in the new message: * e-mail address is removed from the privacy... *

  How to connect to the adapter sector 65? / does not charge my laptop it says that I need to conncet to the AC adapter 65W.

• Satellite A500-19U - games crashes after 3 Min then only connected to the power adapter

  Heys guys. I got my new Satellite A500-19U and install it on some games like COD4, Batman, Assasin Creed and many

  All of these games crashes & freezes after 3-5 Min & gimmea the screen black or white and everything happens while pluging adapter to recharge. When you use the battery, it crashes too, but it takes a long time. Some time, he said (the display driver not responding) & sometimes the screen black or white. The only way to recover the laptop is ALT + CTRL + DELETE and kill the game processes.

  The only one that works such fine bit is Battlefield Bad Company 2. Then I change the DirectX (setting.ini) of car in DirectX9.

  SP please any help on this matter. I think it's a video driver or a Windows 7 problem. And the specifications are:

  Processor: Inter Core 2 Due P7450 2.13 GHz
  RAM: 4 GB DDR3
  VGA: Nvidia Geforce G210M [with the driver from Toshiba Site]
  OS: Windows 7 64-bit

  SRY 4 my English: $

  Hi Storm2005,

  A 64-bit Windows 7 preinstalled on this notebook or install it yourself?

  In my opinion, you should check the cooling options in Windows power management. Make sure that it s set for maximum Performance. This means that your laptop will be cooled as much as possible.

  I put t know how long you have this laptop already but maybe that cleaning is also an option.

• Shift of the computer; It seems that my laptop is lagging when it is connected to the power supply (AC adapter) and it works perfectly fine when it is NOT connected to the power adapter. Can someone help or diagnose the problem?

  This shift of computer thing had never happened before until about a week ago. The shift comes every 30 seconds or more and it occurs also when I switch between applications.

  Hello

  I saw this kinds of problems occur with the power strips and even UPS systems. And some similar questions have
  been solved using them actually, especially the UPS. If the power strip has important circuit protection
  He'll probably bad or you have very low power at first on this AC circuit.

  Solution is not to use the tape and maybe get a UPS with brown-out solution.

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• Satellite L650-12Z: led does not light up when it is connected to the power source

  My L650 doesn't show the white light anymore when the cable is connected.
  The connectors are clean, and the adapter does not work.

  The laptop still works on the farm (when he was still in power in).

  Also without the battery, there is no white light indicating that the laptop is connected to the domain controller.

  Anyone know what could be the problem and how to solve?

  Hello

  Battery is charging while the AC adapter is plugged?
  Are you sure that the adapter is OK?

  If the battery would be charged correctly and if the laptop works ok, only connected to the power adapter (without the battery) the a problem with the frame of the LED may be possible
  But in this case only the technician must test these parts

• Satellite Pro A100 does not connect to the internet if the power adapter is plugged

  Hello
  I have a Satellite Pro A100
  The machine will connect to internet on battery OK. However, if the power supply is connected it does not connect. Any ideas?
  See you soon
  Jim

  Hello

  How do you connect to the internet? With the WLan or cable LAN?
  It s very unusual as the intermits connection when the power adapter is connected.

  This question appears because you buy the laptop?

• Reading of temperature for the use of Thinkpad T510

  Hi all

  I have a question about the standard temperature / acceptable range for computers thinkpad t510 operation. My setup is currently my t510 is connected to an external monitor, speakers, keyboard and mouse. Therefore basically a desktop computer except using the innerds of the laptop as the "heart" of the system. My power manager put the CPU to adapt. The temperature readings that I get for the processor and the motherboard download the program called of Piriform Speccy are on average 60 to 61 degrees C. I wonder if it is within the normal temperature of operation for the laptop and if it is acceptable. What is the temperature not okay and why it is so high, it's that I use external references. Also, I even use heavy workload for the laptop and more for the web, browsing and listening to music and work on documents / spread sheet so basically, office work.

  And finally, the problem of temperature would resolve if I would in the future to get a computer laptop w530 since these laptops are more "powerful"? Or is that evil and the temperature is normal.

  Thanks in advance for answers

  unit88888888 wrote:

  The temperature readings that I get for the processor and the motherboard download the program called of Piriform Speccy are on average 60 to 61 degrees C. I wonder if it is within the normal temperature of operation for the laptop and if it is acceptable.

  Yes ~ 60 ° C is quite normal. I would get concerned if temperature readings consistently exceeded 80 c or if the fan was constantly. Otherwise you will see the temperature fluctuates as activity processor and graphics vary.

• NEW 2 TO DRIVE FOR THINKPAD T510

  Hello, I want to confirm that the Thinkpad supports a 2 TB Seagate HDD.

  ThinkPad T510 - 6 GB RAM - 500 GB HD - 10 WIndows

  As long as it is 9.5 mm thick, it will work.

• ThinkPad T510 problem with the CPU frequency

  Hello
  I was a problem with the CPU frequency - in DC or battery it works 1/2 frequency (1196 MHz), but when my thinkpad plugged and is with battery it works OK (2400 MHz).
  Do you have any suggestions how to solve this problem.

  ThinkPad T510 (4384) intel core i5, 6 GB of Ram.
  Thank you.
  Best regards Nikolay

  What your seeing is actually normal and a result of power management settings. When it is on battery, the reduced CPU clock speed to improve the battery life and only increases in speed if a program requires processing power (games, adobe photoshop, CAD, etc.). If you wish, you can disable this feature by setting the "maximum performance" option in the Lenovo power management program and get into the bios and disable "Intel Speedstep" and similar power options setting. I hope this helps.

  -Brian