Time between

Similar Questions

• The time between VISA W/R

  I use VISA in communication series with PIC18F4550 (mcu, USB copy series), I found if I read immdiately afte writing, I can't get the right data all the time. It seems that the time should be at the same time between write and read funciton, and delay must be greater than 0.35 sec.

  Fact delay is necessary or I used to misuse Scripture VISA and playback function?

  Also look at the use of the chariot of termination and the setting of time-out to your advantage.

  1 turn on the tank of termination (depends on YOUR DEVICE PIC18F4550, read the instructions)

  2 set the timeout to something MUCH longer than necessary. (like 1000 ms)

  Write then followed the reading. No delay, bytes read no. to the port

  For the bytes of lonely bytes expected reading feature request.

  The Read function will wait for the full message that ends with the chariot of termination and will return with your message as soon as he gets the chariot of the termination. Or will he wait until the timeout before giving up on your device.

  You can then decide what to do with if time-out error message never comes.

  I have devices that take more than 3 seconds to answer because they have to go do something before they can meet. Some of my exhalations runs to as high as 10 sec. I have set the timeout on the fly, based on the order that I send.

• Measure the time between the ridges of the periodic input signal

  We have built a circuit which is supposed to mimic an Exercycle.  We have an IR switch and a spinning wheel, the rccb meets a comparator circuit and the output of the element of comparison, we have running in LabView.  We successfully were able to measure the number of rotations of the wheel and the total distance travelled by the wheel, but are struggling to measure speed.  We cannot find a way to measure the time between picks in real time, which we could then divide the wheel circumference and calculate the speed in real time.  The VI I posted has a square wave simulated rather than the signal we receive on our circuit.  Thanks in advance for the help.

  Jon and David

  I think you're overloading the things trying to get the time between two pulses.  Instead, you can use the VI Express your measures and select frequency for her custom. Then, you can multiply the circumference of the wheel of the frequency to get the speed.

  I hope this helps.

  -Christina

• Let a burn of LED on a random time between 3 and 7 seconds

  Hi all

  Probably, it's a matter of simpel for many of you, but not for me. I try to make a counter reaction time. And I hope someone can help me with the first part: the led must Flash on a random time between 3 and 7 seconds.

  After this need to measure the time between burning directed and by pressing the stop button

  Results ranking in a table

  After the display of ten measures of response time average.

  I hope someone can help me to launch it, I need it for school.

  Thank you!

  Matthijs

  Netherlands

  Code Simon put tapped off.  The Down button was a nice touch, but cannot be disabled so we were testing times preaction and the param 'Trial' could get pretty messy especially on a series of rehearsal

• How to find the time between two channels of entry in the data acquisition card or pci 6036

  Hello

  I read a lot-related posts on the simultaneous measurement of two input voltage of similar channels in map data acquisition. I know that the best material is "simultaneous measurments of the Series DAQ cards" but I only pci data acquisition card 6036 and I try to understand what is the time between the reading of the two channels . This period is always constant? (must it rely on a voltage (amplitude, frequency, waveform..). I send the sine wave (s) to the two channels and read the values of V, if they read the same value, the difference should always be zero but I get-0,002 to 0.002 Volt difference (I must find a way to convert it in time). A screenshot of my VI is attached. I wonder how I can accurately measure the time delay between the channel.

  I am open to any suggestion, my final goal to read exactly two channels at the same time ((ou connaître le délai exact donc je peux correspondre les données correspondantes étant donné le temps de retard))

  Hi spinup,

  better you should post your question in the forum of LabVIEW, LabWindows/CVI is used

  Good luck.

• Time between 2 summits

  Hey guys, Hello.
  I need to calculate the time between 2 summits and it does not work very well.

  Can you help me?!

  I'm using NI USB-9221, with 2 channels.

  I need to calculate the time between peak (12 volts) of channel 1 and channel 2.

  Here's my attached .vi.

  Thank you very much for the help.

  This is!

• Take the time between two values

  Hi people,

  I have a problem and I know idea how to solve... I need help.

  The problem is I want to take the time between two values max as you can see in the chart.

  For example, in the image that I have add

  4.5 - 1 840 = 2.66

  And enter this value in the 'time between mostra '.

  It's that I want...

  But what I think is very complicated, because I don't know how to take the time correctly and does remove...

  Thank you very much

  Any solution?

  Hi jocuma,

  I tried something and hope that helps u.

  Just create two arrays of temperature and voltage. First of all, I'll get the value of the voltage when it is more of a certain value and that same index to get the value of time and store in the shift register.

  When I get the second higher than the limit value, I'll get time and subtract the previous value.

• How can I measure the time between each two successive increase edges, using digital input?

  Hello

  I have tried two measure the time in seconds between each two successive rising edges on a digital input.

  So far I managed to detect the rising edge, increment a counter at each rising edge and take the time during which the increase is edge

  all I need now is subtract edge currently rising from the previous era of edge rising to calculate (T), which can be 1/frequency and display in real time for the user.

  but I do not know how to do this

  Can someone help me please!

  Woah!

  Sorry Apok, but your code becomes much too complicated and salty. I don't think that all records to offset or Boolean conversion/operators are necessary at all.

  If you want to measure the time between two keys so it's another (much less complicated) way. It simply records the time when press button in a registry change, then compares the two.

• Measure the time between two digital pulse

  Hello

  For a non-critical calendar application, I need to measure the time interval between consecutive TTL pulses, ranging from the order of 0.5 s for a few seconds, with a low accuracy of +/-10-50ms. The interval being measured varies between the rising edge of the first pulse and the front of the next and so on.

  I have several input lines I need to deal with. Because it's a critical machination low cost, I don't want to use digital counters for each line, so I work with an acquisition of data USB6008 and have connected the input rows TTL on the digital inputs of the device. Avoiding will be sufficient.

  I found a good example of VI on discussion forums that does almost the same thing, only it uses instead of the DAQ Assistant user input. The VI works including the time the program going on in a while loop. I replaced with the DAQ Assistant output (a channel) user input in the hope that it is still work.

  

  When I run the program in "run once" mode, it seems to work perfectly. However, in "continuous run" it measures only a very small interval, probably just the time between two samples.  I think it has something to do with the help of a while loop in combination with the DAQ Assistant. Anyone who has any suggestions how to solve this problem?

  Thank you!

  OK... first of all, you should never use the button "run continuously.  I wish that NEITHER would be to eliminate it, but told me that it is sometimes useful for debugging.  If you want your program to run over and over again, use a while loop with a stop"" button.

  If I'm reading your code correctly, you make your initial moment, and then collect data from data acquisition.  When one of the channels is "T", you stop your loop and the end time of capture.  (By the way, why you convert your table to a cluster?  Why not just index the appropriate channel in the table directly?)

  Since you want to capture the time between two consecutive pulses, you need to know when a transition has occurred... i. e when your digital line went from F (no pulse) to T (pulse start).  This will give you your forehead.  Right now, all you're doing is looking for a value T - so you have no way of knowing if you are looking for to the previous impulse again, or a new impetus.  You also burn 100% of your processor with the way you have your programme in place.

  You need a small loop delay so that your VI is not 100% of your hogs CPU time.  Given that you can live with an accuracy of 50msec, what I suggest that you use.

  See attached picture for you give an idea of how to implement.  He will probably need some refining operations, but it should point you in the right direction.

  

  I hope this helps.

• the BACKSPACE key does not work properly and if I want to enter the same letter twice it takes time between them

  the BACKSPACE key does not work properly and when I want to type a leter twice I have white some time between them

  Hello

  In what program?

  Don

• Nor-Daq 6251 set hour/time between samples

  I'm trying to calculate the expected error for an experience that I do and I don't know if I've done enough to determine the 'break-in' or the time between samples.

  We use 8 differential channels to the maximum sampling frequency, the card can do (1.25. MECH / s). If I understand correctly, the minimum time between each sample must be 1 / 1.25 M, or 800 nanoseconds, such as the maximum time between sampling channel 1 and channel 16 would order 12uS (800nS * 15). If the expected voltage settings are the same for each channel (+/-10v), would a break-in? If so, how long?

  In addition, if a channel is upward, and its tensions have an offset, DC on 5 or 6 volts, should that severely increase break-in if all other channels averaged about +/-1v?

  I'm sorry for the basic question, I couldn't find a straight answer in the documentation.

  Hi LSUgrad85,

  When looking for specific device information detailed Specifications for this device will usually provide the details you are looking for.  After the back if you have questions about the information in the detailed specifications.

  I hope this helps!

  Kind regards

• How to measure the difference in time between the passage by zero of a sine wave and the rise time of a pulse on a same graphic?

  I have a sine wave of 50 Hz and a pulse of the signal on the same chart. The difference in phase between the two is between 0-90 degrees.

  Now I need to calculate the time difference between (when the sinusoidal wave passes through zero volts) and (when the pulse increases). The frequency will remain about even for the two signals.

  The request is for a three-phase generator. In simple terms, when the difference in time between the passage to zero of the sine wave and pulse increases increases, it means that the load on the generator has increased.

  I am a novice user of LabView (version 9, 2009), maybe it's a very simple problem but I was pulling on my hair for the past few days and couldn't understand anything. Any help would be greatly appreciated. I use DAQ USB-6008 to measure these tensions and the impulse of the generator and a sensor

  I have attached a jpg file (a graphic that I just did with excel to explain). The time 't' is what I'm trying to measure

  

  See you soon

  Zdzislaw

  Awais.h,

  For problems of this kind I recommend start writing the granular steps you would take to manually fix this problem.  You can't say LabVIEW (or any programming language) If you can't succinctly describe the solution to your problem.

  The I want to address this problem is to:

  1. find all the zero crossing points and edges on the rise
  2. for every rising edge find the difference between the timestamp and previous passage by zero

  Here is an implementation of this algorithm LabVIEW:

  

• How to set the time between workstations and Server 2008 R2

  Hello world

  I have problem with my Server 2008 R2

  all the workstations on my company doesn't synchronize the time on the domain controller

  I tried many ways to set up automatic synchronization via command prompt (Net time) and its does not work

  Please help me configure the time between the DC and the workstations

  Thank you

  Windows Server forums:
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer/

• Try to shorten the time between songs

  Original title: Media Player

  If I am using windows media player and create a list of songs to play how shorten the time between songs, so we can finish and the next songs will start immediately?

  Hey BillTolbert,

  Unortunately, there is no settings to do such things.

  It's common sense, the songs will be the next song to play won't take long to play.

  The next song begins to play as soon as the first finshes.

  Hopefully this should clarify your doubts.

  Good luck!!!

• Computer clock loses time between stop market.

  A response was that I could use a change of battery, but I got this Dell computer for a year.  Is it possible to change the battery already?

  If he loses time between when you turn off and on again, it's a sign that maybe it's that the CMOS battery has failed.
  Battery size piece, trickle of power is to keep system settings when the computer is turned off.

  They cost about $5 to buy.

  http://www.computerhope.com/issues/ch000239.htm

  http://technofriends.in/2008/05/03/how-to-change-your-CMOS-battery-and-re-energise-your-BIOS/

  How to replace a facility above links.

  Contact Dell 1 as appropriate just in a secured claim: http://support.dell.com/

  Mick Murphy - Microsoft partner

• Svchost size seems to me like svchost (s) becomes larger and larger over time (between restart).

  original title: svchost size

  It seems that svchost (s) becomes larger and larger over time (between restart).

  He/they tend to reach the top of the sort (PWS) in memory of my task manager.

  It automatically get rid of her... whatever... it is now for use by more than one process (when they are no longer used)?

  If not, is there a way for him to say?

  Hello

  Sometimes you try more than once (the link of MVP) and there may be a site
  issue.

  Try this link to my profile
  https://MVP.support.Microsoft.com/profile=D2CBAC3A-D59A-4085-BA97-22B57FD00DF2

  Here is the link to the signature
  https://MVP.support.Microsoft.com/profile/Rob1

  I tried to answer the question in paragraph 1 above. Unless you encounter
  a kind of system problem the SVChost in Taskmanager will vary, in particular
  so shortly after a restart. And when you use the computer SVChost entries will be
  adding and removing management tasks on the fly. Check the information in the upper part
  two links in my previous answer.

  I hope this helps and happy holidays!

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">