Time capsule is not found

Similar Questions

• Airport Time Capsule device not found

  I have the time Capsule on the airport of the TB 3 802.11ac (bought 9/2014).  It integrates the latest version of the 7.7.7.  Just last week, I received the error device not found (.. .has been previously a part of your network... etc.).  The internet connection is always good and the component of the time capsule router still works.  When I unplug the device, it can find him but eventually will go down in a few minutes.  I also did a warm reboot, but some results.  Printer connected to the time capsule does not, nor does Time Machine back ups.

  Would be grateful of any advice on why the drive not found error continues to occur.  Thank you!

  You have Back to My Mac enabled on the Time Capsule?

  If so, turn it off for the moment in the AirPort Utility and restart the time Capsule.

• macOS sierra time capsule does not

  I have upgraded to iOS sierra on my MacBook 2013 and 2015 s pro on 24/09/16. The time machine-

  Time capsule has not worked since. Wifi works but not the backup. We need real expert

  help solve this problem, not conjecture. I understand that if I use others

  equipment suppliers, it can give wrong. But I'm all Apple. Help, please. I should have mentioned

  It's a new time capsule airport which was working fine until I changed the Sierra.

  Thank you

  Bill

  afternoon, this seems to be a common problem - I came here looking for an answer as well. There is a smc / ram p reset fix floating MacOS Sierra - time machinestuck preparation backup on network devices. There is also an exclusion to spotlight some suggest work. I have tried both and neither worked for me, a lot more. I ended up clear time capsule. Airport utility > change > disks > erase disk. has immediately started a new backup and have not had a problem since.

• Time Capsule backup not available without reboot disk

  I have the latest generation of time capsule, but my MBP cannot find the disc inside after restarting the device.  After a restart of the time Capsule the requested backup will take place without any problems, but if I ask another backup later, I again get an alert saying that the disk is not found, requiring another restart. This "solves" the problem, as the MBP can now find the disk and the backup takes place, but the whole point of Time Machine is supposed to be to provide Automatic backgroundbackups.  Any ideas?

  The problem is well known.

  Seen here all the time. Solutions are not so easy.

  We need to know the configuration of the entire network.

  This modem you have, make and model please?

  How is the TC connected and in what mode?

  Is the Mac directly connected to the CT or via the modem that works as gateway?

  Some screenshots of the configuration utility airport helps no end.

• Time Capsule do not write back ups.

  I have a continuous problem with Time Capsule, writing of backups.  After having no problems for a couple of years, TC is now fails to write backup every 3-4 weeks and I found no cause or a solution to the problem.

  TC shows well in the finder, the sparsebundles are there.  Time Machine creates the sparsebundles as usual and will make backups normally for about 3 or 4 weeks.  The error message is displayed "Backup failed" and said that Time Machine is unable to write to the file.  At this time there the existing backup is lost, I have found no way to recover.   I wiped the hard drive via Airport utility, recreated the backup only to fail again in 3 to 4 weeks.

  I've set up another 3 TB HD connected to the iMac USB and have TM write backups on it without problem while the HD TC continues to fail.

  MPB worked until this week and today shows the same error.

  My setup is pretty simple.  iMac connected to TC via ethernet, MBP connected via ethernet.  iMac backup to internal 2 TB on TC's MBP backup 1 TB external connected to the USB TC.

  Apple support suggested that the problem is a bad ethernet cable.  I tried to replace the ethernet cable, no change.  Turn off ethernet using wifi, no change.

  It is not a problem of space, on both drives only half of the available space is used.

  Someone at - he speculate as to the cause and the cure.  It seems to me that the problem is related to the connectivity of TC, the ports are bad?   This is my 3rd TC in 6 years, not real happy with reliability!

  Unfortunately, the TC is probably more reliable products Apple... my opinion.

  It seems that the surface of the disc to the hard drive of TC has one or more faults that are causing backups corrupted after some time. The only good solution is to replace the hard drive inside the TC or replace the TC itself.

  If you think that the surface of the disk is OK on the TC (I don't have, based on the experience), the only other thing to try is a full erase of the TC hard drive using zero on AirPort Utility.  It will probably take 4 to 6 hours or more depending on the size of the player you have on your TC.

  If you don't want to lose the backups to other Macs, you need to copy to another drive before you delete the TC, then copy on once the operation is complete.

• Initial backup, Time Capsule will not end.

  I recently started to use my Time Capsule to back up my early 2014 MBA 13 '' again. However the initial backup will never end. The TC is not used as a Wi - Fi router; It is connected to the existing wireless network.

  When I started having this problem initially. I erased the disc TC and more fresh and Time Machine, under System Prefs, told me that the backup has been chugging along just great. Well... now, after he had all of August to reach the end of time Machine always shows me "waiting for full first backup."

  If I choose "save now" widget menu bar or if I let the system restart automatically backups TM shows Control Panel "backup x of x, XX, XX" and the second number continues to increase. The backup will never end.

  I searched the Ko of Apple and these discussion forums and not found the answer. What can I do to make this backup finish?

  TIA.

  The TC is not used as a Wi - Fi router; It is connected to the existing wireless network.

  And that's probably the problem, because Apple does not officially support backups Time Machine to TB unless you use the wireless TC, or connect the Mac directly on the TC using a wired Ethernet cable connection.

  Things can work with your existing wireless network, but it will be no help if it is not. Sometimes in situations like this, a Mac will back up OK wireless, and another Mac will have problems.

  As you try to add 'new' backups 'old' backup, Time Machine can also have issues with this, try to compare the old and new files and get confused about what to keep and do not keep. In this case, the recommended solution would be to delete older backups of the MBA and then start again and try a new backup.

  Wireless is never recommended for a first full backup. It's OK to use it, then much smaller incremental backups.

  If you try this course the existing wireless you have and still have questions, other than to try to save on the wireless TC, on the only other option to try would be to connect the MBA directly to one of the LAN port <>- on the back of the TC using an Ethernet cable.  Since you have an MBA, who does not have an Ethernet port, you can buy a bolt of lightning for the Ethernet card.  Maid in Gigabit Ethernet Adapter - Apple

• Time capsule is not displayed but the work of WIFI connection

  Hello

  I have a Time Capsule 2 giga, which is used as a WIFI router connected to my normal router via Ethernet and an Airport Extreme, main, used as extension. Until today everything worked well.

  Now, when I open the Airport utility to display the connection, it shows me that the TC and AE are not registered more (device not found). But I can still access the Wifi and internet via networks, I created, but not the backup.

  I unplugged the TC and AE, reconnected them, reset, then the connection worked.

  But now it is again.

  Does anyone have the same problem?

  Concerning

  Unfortunately, this issue is not new and has been reported a number of times since OS X Mavericks.

  AirPort Utility is based on both the mDNS (aka, Hello) and IPv6 IP protocols to find an AirPort base station.

  When access to the airport through the AirPort Utility, try the following, in order, accessibility with the utility check after each step:

  • Check the local connection. If you try to access the airport wireless, make sure that you are connected to its wireless network before running the AirPort Utility to administer it. If you are still unable to access it with the utility, temporarily connect your computer directly using an Ethernet cable to one of the base station's LAN ports.
  • Try to access the base station using the utility file > configure other... option. Then enter the IP address of LAN - side base station (the default value is: 10.0.1.1) and password of the administrator of the base station.
  • Make sure that the base station and your computer are configured for IPv6 link-local only.
    • For a Mac: System preferences > network > Wi - Fi or Ethernet > advanced > TCP/IP tab > configure IPv6: link-local only
    • For the AirPort Base Station:
      Note: You may temporarily connect your Mac or PC directly to the base by Ethernet station to access.
      • From a Mac: AirPort Utility > select the base station > change > Internet tab > Internet Options... > configure IPv6: link-local only
    • Since an iOS device: AirPort Utility > tap the base station > press Edit > tap Advanced > tap on IPv6 > change configure IPv6 to: link-local only > Tap actually
  • The base station power cycle. Remove the power branch of the socket adapter and then wait 15 seconds before plugging back in.
  • Perform a ' default ' reset on the base station.
  • Finally, if you try to access the Airport via an Ethernet connection, make sure that your Ethernet port is NOT configured for Jumbo frames, that is, by using a MTU of 9000 +.

• Time Capsule will not let me delete a corrupted file

  I have a Time Capsule, and a folder on the hard disk called "Temp". In this, there is a corrupted .wmv file that is grayed out and seems to be corrupted to an earlier copy. But when I try to remove it I get: "the operation cannot be performed because one or more required elements was not found (error code - 43).

  I tried this:

  • Restart in Safe Mode, did not work.
  • Disk utility will not find the time Capsule.
  • Taken from the decision-making time Capsule to force a check of the file system.
  • Tried sudo rm - rf in the terminal.
  • Reset the NVRAM.

  I still get the same error and it is not on a Time Capsule image, it is just a normal file. It does not hurt, just bugs the life outta me. Any suggestions on how to remove this file?

  There are a number of things you can try. IF you can see the file in the Finder, I would download a freeware called lock-UnMatic.  http://AlternativeTo.NET/software/lock-unmatic/?platform=Mac is the Mac version of look-a-like of FileAssassin, produced an excellent PC.  Linking the TC for your MacBook, at least temporarily, using Ethernet instead of wireless can be a good thing to do.

  Give it a try, then display your results.  Good luck.

• Time Capsule will not respond to Airport utility

  Here's my situation.

  I have a Time Capsule as my single wireless AP.  The led is green.  All my devices are able to access it without problem.  I can all the Time Machine backups on the internal drive.

  However...

  When I try to access the TC via the Airport on my MacBook Pro (10.10.5) utility I get the next series of notifications:

  (1) when the first attempts to access it, I get the message 'read settings on the Time Capsule XXXXX'

  (2) after a few minutes of this status, I get a yellow triangle with "Device Not Found.  XXXXX Time Capsule was previously part of your network.  Check that it is still within range of your network and it is plugged into a power outlet.  Forget this device removes this network (button) [FORGET]

  When I try to access to utility Airport on my iPad Air (9.2), I am able to access the information about the hardware, but no matter how many times I enter the password, I have no answer.

  The device is not in a convenient place for a direct ethernet access, but it is possible.  Can anyone think of a reason why I can't access via Airport utility?

  Thanks in advance for any help.

  If you did not do a complete network feeding cycle in a while, now would be a good time to do this.

  Turn off all devices on your network..., modem, router, computers, accessories, etc... in any order you want

  Wait a minute

  Start the modem first and let run for 2-3 minutes

  Then begin the next device connected to the modem and let it run for a minute

  Keep a minute out one at a time until the entire network is back of boot devices

  Recheck the network and AirPort on your Mac utility

  Report on the results

• drive time capsule is not available

  The time capsule disk is not available.

  Finally, he worked on 08/08/2016.

  If the capsule is on a wireless network, other devices work on this network? Have you checked your settings on the screen of Airport utility? You've restarted the router?

  The time Capsule is the computer wifi range? Time Capsule shows a green light?

• Flash DRIVE - through works of Time Capsule, but not directly to the Mac.

  What I want to achieve:

  -Access to the USB - stick when it is connected directly to the MBA with USB cable.

  The working configuration:

  -USB-drive ("coffee") connected to Time Capsule and used as an external hard drive to save the files (like huge-any libraries).

  Does not:

  -USB-player ("coffee") is directly connected to the MBA.

  Possible cause:

  -The drive is secured by a setting that I could have done on the Time Capsule and so only time Capsule can access.

  More information:

  

  

  

  Solved!

  Well, then shame on me, but it all seemed to give my user rights to access the drive... I thought about it while searching for the settings on the possession of the car.

  Solved!

• Time Capsule do not pick up address DHCP and cable modem...

  You just bought a Time Capsule and a couple of Airport Express. If none of these devices are connected together via Ethernet, they seem to have set themselves up, and all is well.

  That being said, I tried to create a mobile network instead of pure wi - fi and am studying various behaviors that are not as expected when I rear hub to the Internet Time Capsule, but need to isolate and go 1 bit at a time... (it works not as well as suggest Apple instructions on homelessness of installation)...

  If:

  1. configuration of the modem cable shows that DHCP is 'ON' and supplied address range 192.168.0.x by 192.168.0.y,.

  2 Cable modem wireless is disabled,

  3 Time Capsule Wan is connected to the cable modem, Ethernet

  4 Time Capsule is configured to request its address IP, DHCP

  5. Airport Express is in Bridge mode and have addresses such as 10.x.y.z (appears to be from a Time capsule).

  6. safe as Time Capsule is set to be as DHCP and NAT

  7. There is NO other device in this configuration connected by Ethernet except the cable Modem and the Time Capsule.

  So, why is the IP address of the time Capsule 76.181.45.xyz? (The address is NOT in the range of the DHCP as described in the #1; it is not supposed to be?) ....

  Whence this address?

  A friend says this address puts the "other side" Time Capsule of the cable Modem, directly on the Net?... (Shouldn't worry?) ....

  If none of these devices are connected together via Ethernet, they seem to have set themselves up, and all is well.

  It's because you didn't have the devices connected via Ethernet before you set up the. Given that the installation utility saw a wireless connection, it is assumed that this was the way that you want to connect devices on your network at all times... so he put it this way.

  If you had an established connection Ethernet before you ran the installer, then the utility would have detected this connection and set up the airport to "expand using Ethernet", does not extend to assistance of wireless.

  (it works not as well as suggest Apple instructions on homelessness of installation)...

  If all goes well, you don't talk about this document... Wi - Fi base stations: extend the reach of your network wireless by adding additional base stations Wi - Fi - Apple Suppo... .. Since the 'how' information in this article is at least 4 years late, bear little resemblance to the latest version of AirPort Utility and some of the information are simply not true.  This document if trash is what you... He'll probably do more harm than good with regard to the details of setting.  The article is OK for basic general information, however.

  6. safe as Time Capsule is set to be as DHCP and NAT

  It should not be if your modem is a modem/router "" or type 'bridge' of the device which is also DHCP and NAT services. The fact that you have disabled the wireless on the device confirms that it is both a modem AND a router. That being the case, then you have two devices that both struggling among themselves to try to control the same network... AND do you also have a network error called Double NAT... something you don't want.

  Probably the best at everything again and provide us with the number of brand and model of your "modem", that we can confirm what it is that you have, then the correctly configured time Capsule to work with this device. Once the time Capsule is set up correctly, it will be easy to put in place the other airports.

• Time capsule does not connect to the Internet! Help!

  I bought my own personal modem (surfboard SB6121) and activated with Comcast. I connect to my modem via an Ethernet cable and it works perfectly. But when I connect the modem to time capsule, I can't connect to the internet. I have already restored it and still nothing. The light blinks orange and 2 notification messages I get are no internet connection and no DNS server.

  anything else I can do?

  Apple routers have known problems with some modems... which you have chosen the second worst... SB6141 is most noted as problematic, followed closely by SB6121.

  The question is the more remarkable with the airports of model AC... If TC or AE.

  The perhaps impossible question of fixing...

  First of all turned off, looks that you can not be Exchange to the customer or to the router modem correctly.

  When swap you from a computer directly connected to the TC you MUST turn off the modem for about 15-20 min... you do this?

  Otherwise, it's what it takes...

  If you have already done this... Sorry it is simply the question of compatibility and will not work.

  Are you IPv6 zone you define IPv6 properly...

  See http://mydeviceinfo.xfinity.com/download.php?file_id=35

• Why my computer connects to the wifi via time capsule, but not my iphone, ipad or smart tv?

  Yesterday, there was an internet outage in my area. Eventually he returned to the top, but I could not always connect. I phoned by internet service provider and finally they got it working, except now my computer connects to the wifi, but my iphone, the ipad and the smartTV won't. I use a time capsule to connect. Help, please!

  This modem do you have? Brand and model please.

  It is configured as a router or bridge?

  There is a good chance that the TC I messed up in the trouble... It happens.

  Back to the factory and repeat installation... no file is lost it doing.

  Who is your ISP? What kind of services to wide band?

• Windows PC sees Time Capsule, but not content

  I have two windows 10 PCs, configured the same way (or so I thought). The laptop can see the time Capsule to explore and view the content.  Sometimes, the desktop PC sees the time at the Airport & Explorer utility Capsule, but cannot see the content.  I'm sure it's some settings in Windows and not a problem of TC, but I don't know what to change.  I have active NETBIOS.  Time Capsule (version 7.6.4) is used only as a NAS wireless and not connected to the Internet.  Here are some parameters:

  The IP address starts with 169.254; However, it also shows an IP 192.168

  File sharing is enabled with a disk password.

  The TC has created its own wireless network.

  As mentioned, as the laptop sees the TC and the contents of folders / when I am connected to the wireless network of the TC, and the laptop does not work, I'm pretty sure it's a Windows setting that's my problem.  Last note: desktop PC is connected to my Linksys EA4500 router via an Ethernet cable and wireless network the TC via a WiFi/Bluetooth internal to Intel card model 7260; the office is a NUC Intel that I assembled.  In the past, the Office has been able to connect to the CT; all this occurred when I changed routers of the AT & T combo modem/router to a DOCSIS 3 modem and a Linksys EA4500 router.

  All thoughts welcome, thank you.

  The IP address starts with 169.254; However, it also shows an IP 192.168

  Sorry, but the INVESTIGATION period cannot appear as two different addresses.

  Your installation of the TC program is unusual... and will cause problems...

  So can you please give me the installer with some screenshots.

  I can also ask why are you keeping the independent TC of the main network... which just makes life difficult. If you are forced to do so for a reason any logistics... so let me help you find a way to do within the existing network, rather than in a different subnet.

  When you try to access two different IP subnets at the same time... gateway and DNS issues come to the front.

  So it is not really going good work with an address 169.254 since it is self generated.

  I'll assume that your linksys EA4500 takes the 192.168.x.x address which is default for linksys products.

  Please change the TC in router mode... That is to say DHCP and NAT. (there is no reason that it cannot be connected to your network via the WAN port with this configuration).

  You can ignore or not connected WAN warnings or cautions Double NAT.

  By default, the TC will have IP 10.0.1.1

  Define the NUC to take a static address on the... wireless card for example 10.0.1.10 with subnet 255.255.255.0

  There must be no bridge and no dns configuration. Let the empty... or use the 192.168.1.1 address of the EA4500 (check the actual number of the ethernet configuration).

  Once you have the IP address it should work.

  Centuries ago, I wrote how to Mac installation... It's pretty close to the same for PC.

  Time Capsule using wired for Mac for backup only.