TMS DEVICE DATA PORT

Similar Questions

• ENVY 700-527c: data port availability

  ENVY 700-527c, regarding with card mother Kaili2.

  This unit had a place available for an additional cd/dvd drive for a total of 2 cd/dvd players.

  In addition, there are two bays available for the additional hard drives for a total of 3hdds.

  I installed a dvd drive in the extra Bay and I installed a hard drive in one of the two available bays. Everything works well no problems.

  I would like to take advantage of the third Bay for an additional hard drive, but there were only two available data ports.

  You can see the data ports in the lower right. Currently, all four are busy (2 dvd/cd drives - hard drive 2).

  My question is: How can I get a third HDD installed and operational?

  Hello

  The RED edge connector is a different SATA port.  See the image below.

  

  Motherboard taken Kaili2 supported by six SATA 6 devices. Five traditional SATA III ports and an MSATA are available.

• JOINT-2-data ports

  Hello

  I took over managing a JOINT-2 6500 implementation, as far as I can see it has been configured in

  "Promiscuous" mode with a single virtual sensor assigned to two data ports 0/7 & 0/8.

  The switch was configured with the following options:

  intrusion detection module 8 access management port - vlan 507
  intrusion detection module 8 ports data access 1 - vlan 507

  monitor the 66 session source vlan 501-509, 518-520, 601-613
  monitor the session 66 intrusion-detection-module 8-port data destination 2

  can someone tell me why the data port of second order utilsed 1 and the background command uses the data port 2, it's valid and recommended?

  Thank you

  D

  So a little bit about the architecture of the JOINT.

  JOINT has a management or command and control (gig0/2) port and 2 data (gig0/7 & gig0/8) ports

  These ports on JOINT connect to the 6500 on the backplane.

  JOINT Gig0/7 connects to the data port 1 on 6500.

  JOINT Gig0/8 connects to the data port 2 on 6500.

  The configuration involves two things:

  1 setting up JOINT (Date, time, assigning virtual devices to interfaces, tuning signature... etc.)

  2. configuration of 6500 to send traffic to the JOINT.

  You plan to put the JOINT in promiscuity or inline mode?

  The configuration on the 6500 is different for the two modes.

  Configuration:

  intrusion detection module 8 access management port - vlan 507

  This puts the management port to vlan 507

  intrusion detection module 8 ports data access 1 - vlan 507

  Puts data port 1 in vlan 507. This is usually done in inline mode.

  monitor the 66 session source vlan 501-509, 518-520, 601-613
  monitor the session 66 intrusion-detection-module 8-port data destination 2

  It is an extended configuration that sends a copy of the data from the VLANs to the port of data 2.

  This is done when JOINT running in promiscuous mode.

  So in your case, the configuration is correct on 6500 sending traffic to JOINT depends on what mode, you want the METHOD to be run in.

  Please see the link below which will explain how to configure 6500 promiscuity or JOINT configuration in inline mode.

  http://www.Cisco.com/en/us/docs/security/IPS/7.0/Configuration/Guide/CLI/cli_idsm2.html

  Let me know if you have any questions.

  -Sid

• hidden data port 2 on Mac Pro 1.1

  No one knows what that Apple engineers have reason had to have these two ports on the motherboard? Discussions I read suggested that they were for the installation of additional optical drives, but I just watched a youtube video that has already shown the optical drive port has additional sata cables already in there.

  2 are there thing, data ports, but I don't see a pair of extra power cables. It has been designed a bit more from the Commission? Or was there a plan that Apple abandoned.

  Wiring in optical bays in Mac Pro 1.1 to 3.1 2008 model have ATA/IDE wiring in optical bays, connectors from molex power 4pin.

  In my view, Apple has included these two additional SATA ports to guard against optical disk ATA/IDE, becoming too expensive or outdated form. Additional ports gave them the data connection to allow them to switch to SATA optical drives (with duplicator of molex power 4pin or adapter) without revision of the motherboard.

  There is no explanation of how to use them in any official literature from Apple. They are too close, and using both requires using at least a right angle connector. Practical power is expected, because they were never for your convenience. Research of power for additional disks attached here is your problem. (learn about amateur sites)

  For the great re-design for the 2009 model, these ports were eliminated, and the optical bays got SATA wiring (including power SATA).

• PXI-6551 device data Underflow

  Hello.

  I have a module, PXI-6552.  I need to enter my DUT (ADC) out after a very long and very precise vector sequence.  And I want to loop through this sequence of more than 1 000 times (at the average of the results).

  The following script works:

  script ADCcapture
  generate marker0 of vecsetup (0)
  Repeat 1000
  generate marker0 of vecsample (424)
  end repeat
  end of script

  Here are the sizes of waveform for each wave listed:

  vecsetup = 280 cycles
  vecsample = 262 060 cycles

  My sample = 512 MB record length and the number of records to capture = 1 001

  The first marker in my script is my trigger start for my CQI. session.  The following markers are triggers of the advance.

  As I said, this example works, but the "vecsample" waveform is much smaller than it should be.  It should be 5 times as large, but I don't have a lot of memory.

  Fortunately, most of the 'vecsample' is a sequence repeatedly to keep living clocks (in my example above are just exhaustively written in the form of ongoing vectors).

  I know I can't nest, and I know now that I can't embed instructions more than 55 inside my finished loop (repeat 1000).

  Then, I tried to break my my 'vecsample' signal break up into 3 sections that I could "split the difference" between the size of memory limitations and the script of vector:

  script ADCcapture
  generate marker0 of vecsetup (0)
  Repeat 1000
  generate marker0 of vecsampleA (424)
  generate a vecsampleB
  generate a vecsampleB
  generate a vecsampleB
  ...  (Note: I have exactly 50 copies of 'generate vecsampleB')
  generate a vecsampleB
  generate a vecsampleB
  generate a vecsampleC
  end repeat
  end of script

  Here are the sizes of waveform for each wave listed:

  vecsetup = 280 cycles
  vecsampleA = 1 660 cycles
  vecsampleB = 4 884 cycles
  vecsampleC = 16 200 cycles

  vecsampleA contains unique things initially, including the previous sampling period output ADC.
  vecsampleB contains 1 221 best x of the model 4 time keep alive clock that I need.
  vecsampleC contains unique things at the end.

  Yet once, my record sample length = 512 and the number of records to capture = 1 001

  In the end, this generates the same number of cycles as the previous example:
  1 660 cycles 4 884 * 50 + 16 200 plus 262 060

  However, when I run this new script, I get an error:

  Exception detected
  Detail: [-1074115901] Windows error 0xBFFA4AC3
  Description of the DLL: DAQmx 200316 error has occurred:
  Measurements: Device data precision passing. The device was not able to move data quickly enough to deal with the frequency of sampling for the active script.

  Perform the operation at a lower sampling rate, or are looking for the following in the current script: markers can be too close together, waveforms is too small, wait may be too short or subsets may be too small. If you are using an external clock, the clock provided might have disappeared during your generation.

  State code:-200316

  Sorry for the long post.  Any help is very appreciated!
  Brian

  PS: I found the following topic regarding this issue, but it has not helped me to understand my mistake (as it seems that my markers and waveform sizes seem to be big enough):

  http://forums.NI.com/NI/board/message?board.ID=70&message.ID=10306

  Hello Brian,.

  I've recreated your problem on my side, thank you for the detailed description of your problem, it makes it much easier to understand what was going on.

  Although I'm still looking at the root cause of the problem, there seems to be a problem with the number of orders in the repeat loop. You need 2 less commands within the repeat loop. This can be demonstrated that the problem by moving two of orders outside the loop, keep the same number of lines in the script, but less than two lines in the loop to repeat itself.

  In your case I want to double the size of the vecSampleB and only run 25 times. This should allow you to start going forward.

  With regard to the underlying issue, when I find I'm going you know.

• I can not get the automatic updates on my samsung jack sgh-i616. _ "connection to the update server is not available. Check your data connection settings and make sure that the device date and time are correct "___RESULT CODE: 80072ee7__ _"

  I can't get the automatic updates on my samsung jack sgh-i616.

   

  "Connection to the update server is not available. "Check your data connection settings and make sure that the device date and time are correct.

   

  RESULT CODE: 80072ee7

   

  -It is a windows mobile 6.1
  
  
  Thank you very much! = D

  As a guide.

  This error code translates ERROR_INTERNET_CANNOT_CONNECT.

  You may encounter temporary connection related errors when you use Windows Update or Microsoft Update to install updates
  http://support.Microsoft.com/kb/836941

  Harold Horne / TaurArian [MVP] 2005-2011. The information has been provided * being * with no guarantee or warranty.

• Replace the TMS device

  Hi all

  I only appliance TMS with VCS and TMSagents (applications MOVI), then my TMS has error and had to be replaced by a new.

  is there any procedure to do this replacement for the TMS have TMSagents with VCS to ensure that replication will not be problem. Sorry, I just worriying on replication to be failed.

  because I have a large number of users MOVI.

  Thank you all

  Hello Kalinda

  What kind of error you see on the server of TMS? Maybe the ist possible to fix it?

  Before you replace your server TMS device, you need schedule downtime for maintenance.

  You should back up your sql database and the agent MSDS database. Then install the new TMS server with the corresponding version of the former and restore and backup agent MSDS database. You can then enable replication again.

  Keep in mind that the TMS appliance server is EOL and EOS, but also you can be able to take advantage of the Cisco migration program.

  Please visit this link:

  http://www.Cisco.com/en/us/prod/collateral/ps7060/ps11305/ps11316/ps11338/end_of_life_notice_c51-683062.html

  Concerning

  Rafal

• Cisco TMS device virtualization

  We will virtualize the TMS device to a virtual machine, but had a few questions regarding the parameters:

  1. are there things that I have to watch what is using the same IP address?

  Let's change the name of TMS

  2. do I need generate a CSR that is new for a certificate, once I have install TMS on the new VM?

  I guess that Yes

  3. should I stop replication on our control VCS and highway regarding MSDS?

  4. any other telepresence infrastructure changes I have to make before you migrate the virtual server?

  1. Are there any things I need to watch out for in regards to using the same IP address?
  
  We will be changing the name of TMS
  

  You change the domain name FULL of server TMS, or do you mean that the actual name of the server is changing?  As long as you do not change the IP/domain name FULL you'll be fine with respect to systems added to the MSDS.  If you change the name of the server, you'll want to change it in the TMS using TMS tools.  See the most recent Administrator's guide, that I don't remember the name of the option.

  2. Do I need to generate a new CSR for a certificate once I install TMS on the new VM?
  
  I assume yes
  

  We use a wildcard certificate, so we are able to download the same certificate on all our servers no matter what they are as long as they use our domain.  Depends on your configuration.  Unless I understand this question, that I can't have the certificates for our group, just know enough to get.

  3. Should I stop replication on our VCS control and expressway in regards to TMS?

  Probably the best.

  4. Any other TelePresence infrastructure changes I need to perform prior to migrating to the virtual server?
  

  We have migrated our MSDS from a virtual machine to another, at the same time, adding a second server for redundancy.  As long as you don't change the IP or the FULL domain name depending on how you have your systems point to TMS, you should be fine.

• What is a data port?

  Hello
  
  I'm confused at first data ports. The ports of database the same as the listener ports?
  
  I have 15 databases on our windows 2003 server. Combination of 9i, 10g, 11g
  
  It has 3 types of headphones for 9i, 10g and 11g.
  
  5 Database 9i uses listener9i with port 1521 = > does that mean their database port is 1521?
  5 10 g database using listener10g with port 1522 = > does that mean their database port is 1522?
  5 11 g database using listener11g with port 1523 = > does that mean their database port is 1523?
  
  If I merge all 3 headphones in the earphone of 11g with port 1523. Does this mean all my 15 databases has the same port which is 1523?
  
  Is it possible that 1 database can be registered 3 listeners, so it can have 3 different ports?
  
  It follows, then, that the port of the database is not send to each database?
  
  
  
  Thank you
  
  Published by: 843228 on April 11, 2011 03:19

  843228 wrote:
  Hello

  I'm confused at first data ports. The ports of database the same as the listener ports?

  I have 15 databases on our windows 2003 server. Combination of 9i, 10g, 11g

  It has 3 types of headphones for 9i, 10g and 11g.

  5 Database 9i uses listener9i with port 1521 ===> is does that mean their database port is 1521?
  5 10 g database using listener10g with port 1522 ===> is does that mean their database port is 1522?
  5 11 g database using listener11g with port 1523 ===> is does that mean their database port is 1523?

  If I merge all 3 headphones in the earphone of 11g with port 1523. Does this mean all my 15 databases has the same port which is 1523?

  Is it possible that 1 database can be registered 3 listeners, so it can have 3 different ports?

  It follows, then, that the port of the database is not send to each database?

  Thank you

  Published by: 843228 on April 11, 2011 03:19

  the fundamental flaw in your thinking is that databases do not use ports at all! The listener uses a port to listen for connection requests. A listener, with the default LISTENER name, running an oracle home, listening on a single port, use easily - is designed to serve--multiple instances of database in several versions of several houses. It is unnecessary complexity to try to have several headphones or to name the listener as if she belongs to a customer or a specific database. It's like the telephone company, to build a separate table for each customer.

• Upgrading to Windows 7: compatibility of the device data could not be loaded

  I tried to upgrade my L300 (and otherwise my P300) from Vista to Win 7 with two DVDs of upgrade provided by Toshiba end 2009. I followed all the instructions, as to recover the system to the State of delivery, deletion of outdated drivers and install new drivers with the DVD driver. But when I insert the Win 7 DVD and start the installation, I soon get the following (originally in German) error message:
  "The device compatibility data could not be loaded. Error code 0x1F.*.
  German support Toshiba could not answer my question so far, then I wonder what is the problem and how do I get my installation is going. It's kind of frustrating after paying for the upgrade DVD, but the installation does not work.
  Thanks in advance for any help on this error.

  And after a year using it for the first time now, right?

• One of the USB devices attached to this computer has malfunctioned and Windows does not recognize it. The location is the root (2 ports) USB hub: 1-unknown device and Port 2-not used

  Original title: USB device not recognized

  Over the last 2 weeks, I get a message on a USB device.  The message said that one of the USB devices attached to this computer has malfunctioned and Windows does not recognize it.  The location is the root (2 ports) USB hub: 1-unknown device and 2-unused Port.  I have no idea what it means.  I hesitated to first click the icon (it does not last very long) thinking it could be a scam.  Can someone help me?  Thank you.

  Hello

  (1) is the specific question of specific USB devices?
  (2) did you of recent changes to the computer before the show?
  (3) have you tried plugging the USB stick on another computer?

  (4) what is the brand and model of the computer?

  I suggest to refer to the following methods and check if it helps to solve the problem.

  Method 1: Hardware devices do not work or are not detected in Windows

  Run Microsoft Fixit mentioned in the article.

  http://support.Microsoft.com/mats/hardware_device_problems/en-us

  Method 2: USB Port may stop working after you remove or insert a USB device

  http://support.Microsoft.com/kb/817900

  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756 How to back up and restore the registry in Windows

  Reference:--

  Advanced troubleshooting tips for General USB for Windows XP problems: http://support.microsoft.com/kb/310575

• N2048 - VoIP QoS, data Ports and trunk Configurations

  Hi all

  I am new here and also new to work with the Dell Networking hardware. I just need to some insights into setting up a new network, that I put. We use 3 switches to N2048 for access to data and VoIP. Each port will have only have only a phone or a client PC in different VLANS.

  My question is what is the best configuration across all three powered to ensure that we have the optimum configuration for the quality of service for VoIP phones. Here is the configuration that I came up with this day.

  Global configuration

  VLAN, VoIP

  Voice port

  item in gi1/0/1 interface
  switchport mode access
  switchport access vlan 5
  VLAN 5 voices
  Voice vlan dot1p 5
  output

  Client port PC

  access mode swithport
  swithport access vlan 10

  Trunk Port

  Te1/0/1 interface
  switchport mode general
  VLAN allowed switchport General add 5,10,100
  switchport General pvid 100
  VLAN 5 voices
  output

  Thanks for the comments

  By default, the ports are configured to trust the priority of incoming user. So for your switch connections you can configure ports and trunk mode, there is no need to set general mode with VLANs voice, etc.

  switchport mode trunk

  switchport trunk allowed vlan add 5, 10, 100

  switchport trunk vlan 100 native

  For ease of deployment, I suggest to all the other general mode ports.

  switchport mode general

  VLAN allowed switchport General add 5,10

  pvid switchport General 10

  VLAN 5 voices

  With the general mode configuration, you can connect a client or a phone, or both at the same time, in a port. This will make things easy if later you decide to plug a phone in where a customer to reside.

• Disable devices Data Services?

  Hello world

  Can disable/data services on the device by programatically please help me its too urgent for me

  You can programmatically disable wireless radios, but you cannot disable just the data service programmatically.

• BlackBerry Smartphones device date and time will not

  I have a BB Torch 9860. Unit date and time is wrong, but I can't change it because the icon in the panel display and controls, update is marked with a lock symbol auto. Also the Auto update time zone: display the prompt with a lock symbol. Network time is correct. Can anyone help with this please. Thank you

  Sounds like policy. If this device is on a BES and controlled at least partially from your employer, you need to talk to your employer or your employer, IT people. If it is under your full control and of your device, then there is no problem in removing a COMPUTER policy.

  See http://www.blackberry.com/btsc/KB30076

  If you have a COMPUTER policy, see http://www.blackberry.com/btsc/KB14202

• BlackBerry smartphones, Palm Desktop 6.2 to Blackberry without Outlook or Palm device data transfer

  Just got my new Blackberry Tour.  My Palm T / X is dead, but I still run the Palm Desktop for my calendar & contacts.  Tried to create a spreadsheet Excel and then running via Outlook by another suggestion posted, but for some reason any, I can't Outlook to open!  So is it possible to transfer data without using outlook and without having a Palm device to use?

  Thank you!!!

  If you have data in Excel, you can save the excel file in an ASCII text and file import/synchronization of the device through the Desktop Manager.

  Visit this link, ignore the part about the error and scroll to the specified resolution and follow the directions.

  KB12351 Error message when the transfer of contacts from Palm Treo on the BlackBerry device