Similar Questions

• NO category 'series & parallel' in MAX, but NI-VISA installed, please don't help

  Hello, I installed MAX (measurement and Automation Explorer) 5.1.0f0 Runtime of NI - VISA (5.1.1) and also direct,

  but there is NO 'series and parallel' in 'Devices' (Geräte und interfaces).

  What's wrong?

  I already reinstalled and restarted the PC, but nothing helped.

  Any idea?

  

  Ahhh,

  I'll have to download OR-Serial

  

  I thought, NOR VISA is enough...

  Ok

• Series, parallel, USB ports are available in ESXi?

  Hello

  I am currently using the ESXi 4.0

  I have read the knowledge base,

  and found the step to activate the devices USB, Serial Ports and Paraller.

  But it is still not able to work.

  Can I know what step I'm bored or something else I don't have success install?

  Please please help me on this.

  If you want to use the real serial ports - you have two options:

  (1) install a serial to IP device

  (2) not use ESX, ESXi. ESX are supported by two parallel port forwarding and VM series

  ---

  MCSA, MCTS, VCP, VMware vExpert 2009

  http://blog.vadmin.ru

• Visa series parallel read with arduinos, data are delayed

  Hello

  Currently I use two arduinos asynchronous data read from sensors of temperature and humidity. Each arduino send back 4 floats, separated by commas, with a stop of "\n" character In labview, data gets broken upward and then pushed to live plots. In addition, the data gets written to a file - arduino #1 and #2 Arduino have their data sent to different files. It is important to note that the arduinos have different rates by which they send data on the comms series. Ideally, we would like that the data of every arduino to enter and update locations independent real-time each other.

  I'm having a problem where data do not seem to be displayed in real time. I can touch a thermocouple and then ten seconds later, the temperature will change. This delay seems to grow over the short program, which is a problem since we use a direct result of the plots to determine when to start various processes of cooling.

  I wonder if due to different data rates the thrust arudiunos, if there is some kind of buffer somewhere that has a "backlog" of the fastest arrduino data and must wait for the slower arduino data until it does nothing. It is obviously a problem of data flow, but I'm pretty green with LabView and was looking for some advice or pointers. I want to mention that the arduinos send data quickly; they send every two seconds or more.

  Hello MrScientist,

  can you please try to use two separate while loops, one for each COM port, because if they're in the same loop, it can happen that they block each other.

  A second option is always read all the information on the COM port and made a ring buffer and filter information of these buffers.

• the NI 9871 serial ports appear also in MAX with built-in serial ports of the target - under devices and Interfaces IS NOT? NO NEITHER 9871 (Scan Interface)?

  Hi - Have cRIO

  Can someone help me get the NI 9871 (Scan Interface) work?  My two 9477 and two 9425 and 9403, function with the scanning Interface.  In MAX > software > NOR-Serial RT 3.82 > NOR-Serial 9870 and Scan Engine Suport 3.8.2 9871 BUT NOT == MAX > devices and Interfaces > series & parallel = number of Ports Com for 9871 listed?   Project, 4-port RS-485 NI 9871 is in slot1?  Any help appreciated thanks

  the serial ports on the NI 9871 also appear in MAX with serial ports integrated target under devices and Interfaces

   

  NEITHER 9871 (Scan Interface)

  I left the Slot 1 Slot 8 9871 Know works and MAX displays 4 COM ports.  Something is misconfigured in Slot1?

  Solved!

  Thank you

• No resource VISA in Labview but all present at MAX

  Hello

  I am unable to find any resource VISA of LabVIEW, however, all materials are available and functional in MAX. I just installed a PCI-8433/2, but also a BOBBIN NI PCI-8512 / HS card. As part of the installation, I think that MAX has been upgraded to version 4.6.2. I will attach the report of max configuration for those who are interested. I work with LabView 8.2. I also uninstalled an agilent GPIB card and thus the NI GPIB card is the only controller and GPIB0... instead of the card of agilent.

  I had a similar problem before that it was the result of a corrupted database, but I was unable to find this issue on the forums this time and I don't get any errors. Just an empty control VISA resource.

  Any suggestions would be greatly appreciated.

  Nate

  MAX Configuration report

  2010-12-27 13:35:05

  Summary of MAX

  • My system
    • District data
      • POUVEZ channels
      • NOR-DAQmx tasks
        • V1P1V2P2
        • V3P3
    • Devices and Interfaces
      • GPIB0 (PCI-GPIB)
        • Instrument0
        • Developpement1
        • Instrument2
        • Facility.3
        • Instrument4
        • Instrument5
      • VISAS various resources
        • GPIB0::INTFC
        • GPIB0::16:INSTR
        • GPIB0::2:INSTR
        • GPIB0::22:INSTR
        • GPIB0::7:INSTR
        • GPIB0::10:INSTR
        • GPIB0::27:INSTR
        • GPIB0::3:INSTR
      • Network devices
      • NOR-DAQmx devices
        • NEITHER USB-9481: "Dev2.
        • NEITHER USB-9481: "Dev1".
      • NOR-XNET devices
        • NEITHER CAN PCI-8512 / HS
          • CAN1
          • CAN2
      • PCI-8433/2
        • PORT1
        • PORT2
      • (Unidentified) PXI system
      • Series & parallel
        • COM1
        • COM6
        • COM9
        • LPT1
    • Scales
    • Software
      • IVI Compliance Package 3.3
      • LabVIEW 8.2
      • LabVIEW Run-Time 7.1
      • LabVIEW Run-Time 8.0.1
      • LabVIEW 8.2.1 Run-Time
      • LabVIEW 8.5.1 Run-Time
      • LabVIEW 8.6.1 Run-Time
      • LabWindows/CVI Run-Time 9.0
      • Measurement & Automation Explorer 4.6.2
      • Measurement Studio for VS2005
        • DotNET
  • Commune
• OR LabVIEW SignalExpress 3.0
• NEITHER Spy 2.7.1
• NOR-488. 2 2.46
• NI-CAN 2.7
• NOR-DAQmx 8.7.2
• NOR-PAL 2.5.3
• NOR-Serial 3.6
• NOR-USI 1.0.2
• NI-VISA 4.6.2
  • NiVisaServer.exe
  • NIvisaic.exe
• Duration of NI-VISA 4.6.2
• NOR-XNET 1.1
• IVI drivers
  • Advanced
    • Instrument Driver software modules
    • Simulation software driver modules
    • Pilot simulation sessions
  • Pilot sessions
  • Logical names

Now that IS odd.

Can you show some screenshots of MAX?

First, expand the software tab and post a PNG of the screenshot (I am not yet convinced that you have not a driver issue)

Then select MAX > TOOLS > NI VISA > VISA Options - Wait for the new screen then expand General settings Mysystem, and select alias.

You can also try 'Clear all the aliases' a from there and restart.

• Satellite M60 recognize converet series, but not anything else, why?

  Hi guys again.

  My Satellite is recognize the series converter I plug into a cable of multiparaller but there is nohing more. If it's that the series converter should - not recognize and pararell cable also? Maybe I'm wrong paraller cable connection?

  Or soap operas is ok for the Satellite, but no parelles?

  I don't understand what exactly you want to know. All what I can tell you is, that Windows will recognize the converter series / parallel, but not the cable itself, because there is no active component.

  You will need to connect to a device such as a printer or something like that. These converters sometimes need specific drivers. Have you checked that they are installed correctly?

• Upgrade of RAM max on Satellite Pro 4300

  I want to upgrade RAM of the Mod: SP4310 and SP4340.

  The Toshiba manual for 4300 series says:
  Mem Max 567 MB with two 256 MB modules.

  Sites WWW in Kingston and transcend the say:
  Mem Max 320 MB with two 128 MB modules
  (144 pin SODIMM PC100)

  What information is correct?
  Best regards, Hans

  Hello Hans,.

  The information that I was able to get show that the series 4300 has 64 MB of RAM non-removable and two expansion slots whish can each take a 128 MB RAM module, which gives a total of 320 MB.

  Kind regards

• Max RAM?

  Hi all

  I have a HP dv7-4070us (i5 - 450, 180 SSD Intel 330 1 TB WD Scorpio Blue, Windows 7 Edition home premium 64-bit, 8 GB RAM, ATI HD 5650) currently I begin to learn software Adobe master suite, of things quite dense, however, I realize that up to 8 GB of RAM is kind of pushing my system, (I like to multitask) so I was wondering if it was possible to move to 16 GB of RAM Since I was 8 GB now. The original information stated as 8 GB max Ram, but I read here (http://support.hp.com/us-en/document/c00820047) for my system, in accordance with article

  "Taken maximum memory supported by the operating system", max ram is 16 GB. So, is the upgrade to 16 GB possible or is it just wishful thinking? I know that the macbook pro recommended max ram is 8 gb, but other people have found that this max ram is actually 16 GB, this could be a similar situation here? Thank you very much!

  EDIT: just realized I posted in the forum display section... Sorry

  Hello:

  As well the manual maintenance and the State plug of the maxiumum for your system memory is 8 GB.

  Service manual, Chapter 1, page 3.

  http://h10032.www1.HP.com/CTG/manual/c02666747.PDF

  Specifications of product page...

  http://support.HP.com/us-en/document/c02207147

  If your laptop is the Intel 5 series chipset, the max memory is 8 GB.

  The service manual indicates your PC a series Intel 5 (HM55) chipset (Chapter 1, page 2)

  If it has the Intel 6 series chipset, the maximum memory is 16 GB.

  Normally, if the PC is shipped with processors intel generation second, it can take 16 GB of memory.  Your i - 5 450 is an Intel 1st generation of processor.

  The information you read on this link you posted affect how the operating system memory can answer, not how much memory material can respond.

  Paul

• sbrio9636 error VISA-1073807202

  Hello

  I have a sbRIO9636 and test instruments. I want to just connect sbRIO and test instruments (with RS-232).

  I am trying to connect RS232 (9 pin) via serial ports... I also Measurement & Automation Explorer (version 5.1) to monitor and configure the series/parallel connections.

  The problem is that when I have a request, it seems that my device is not correctly recognized. I get errors of expiry.  VISA-1073807202 error. But when I connect Test instruments directly to the PC, NEITHER Max shows COM 1 and can get the data from the trial instrumnets. This means I can get the data from the PC, but I can't do the same with sbRIO9636.

  How can I make sure that my device is correctly recognized? My COM1 port is enabled at all? I don't see COM Port NI Max for sbRIO9636.

  Thank you!

  Hey, Kellydog

  It is a Ko what VISA-1073807202 error.

  http://digital.NI.com/public.nsf/allkb/10C6C0FBB8E7BD4486257850006CE8FF?OpenDocument

  Maybe this will fix the problem.

  Best regards

• My PCI-6250 does not see my SCXI box

  Hello

  I want to install a station using a PCI-6250 connected to an SCXI chassis cable 68 pin.  We have a couple of these formations, so they gave me a Setup disk that have our configuration is already done.  However, I had to install a software, that they neglected to give me.  I got the latest driver for the latter of NOR.   Well, maximum running, my tree is distinguished by a previous configuration.  And mine is not communicating with the SCXI.  My cards are "x" ed out.  The Communicator 'chassis' in the SCXI chassis Configuration is grey (no options).  I checked the wiring and disconnected all the blocks for the cards.

  Here is my tree.

  NOTE: Mine also does not have the "NOR-DAQmx devices" under the heading "devices and Interfaces, only in the software section.  Other configurations have this list.  I don't know how to get "devices OR-DAQmx" shown.

  Any help would be appreciated.

  My system

  • District data
  • Devices and Interfaces
    • GPIB0 (GPIB-USB-HS)
    • Network devices
    • OR PCI-5402 'Dev1 '.
    • OR PCI-6250 "Dev2.
    • OR SCXI-1001 "SC1".
      • 1: OR SCXI-1125 'SC1Mod1 '.
      • 3: OR SCXI-1124 'SC1Mod3 '.
      • 4: OR SCXI-1160 'SC1Mod4 '.
      • 5: OR SCXI-1163R 'SC1Mod5 '.
      • 6: OR SCXI-1163R 'SC1Mod6 '.
    • (Unidentified) PXI system
    • Series & parallel
      • COM1
      • COM2
      • Com7
      • COM8
      • COM9
      • COM10
      • LPT1
      • LPT1.4
  • Scales
  • Software
    • IVI Compliance Package 4.0
    • LabVIEW Run-Time 2009
    • LabVIEW Run-Time 8.0.1
    • LabVIEW 8.2.1 Run-Time
    • LabVIEW 8.5.1 Run-Time
    • LabVIEW 8.6.1 Run-Time
    • LabVIEW SignalExpress 2009
    • LabWindows/CVI Run-Time 9.0
    • Measurement & Automation Explorer 4.6.2
    • Measurement Studio for VS2005
      • DotNET
  • Commune
• Editor Script OR 1.3.1
• NEITHER Spy 2.7
• NOR-488. 2 2.73
• NOR-DAQmx ADE support 9.0.2
• NOR-DAQmx Device Driver 9.0.2
• NOR-DAQmx MAX Configuration 9.0.2
• NOR-FGEN 2.5.1
  • FGEN Soft Front Panel
• NOR-HWS 1.4.5
• NOR-PAL 2.5.2
• NOR-TClk 1.6.1
• NOR-USI 1.0.2
• NI-VISA 4.6
  • NiVisaServer.exe
  • NIvisaic.exe
• Duration of NI-VISA 4.6
• NOR-DAQ traditional 7.4.4
• IVI drivers
  • Advanced
    • Instrument Driver software modules
    • Simulation software driver modules
    • Pilot simulation sessions
  • Pilot sessions
  • Logical names

Hi mz6yx6,

First of all, don't worry about trying to get to the ' devices OR-DAQmx "appear. 4.6 Max, which was first included with NOR-DAQmx 9.0, has a revised UI layout which displays the devices inside "Devices and Interfaces" rather than display them in subfolders like ' devices OR-DAQmx.

Also, thank you for the view a report of the configuration of the system MAX. The report shows that the SCXI chassis and modules are configured as simulated devices, which I think is the problem. DAQmx (> = 8.7) does not support configurations where a simulated SCXI chassis and modules are connected to a real communication hardware DAQ. Since your system has not simulated hardware DAQ (except the SCXI chassis and modules), the "Châssis Communicator" menu has no options to display.

To resolve this issue, remove the SCXI chassis in MAX and create a real one (not simulated). How to do this depends on if you manually configure the chassis or you import a configuration from a file .nce, .ini or .txt:

• Manual: right click on "Devices and Interfaces", then select «Create a new...» ». In the window "new...". "which appears, open the ' Chassis SCXI of NOR-DAQmx ' subtree and select the chassis type from there. Do not select "Simules NOR-DAQmx device" or modular Instrument The modules must be detected automatically, but you will need to manually reconfigure the accessories.
• Import from a file .nce, .ini or .txt: in the dialog box 'Assistant Import Configuration', check that the 'Warnings and conflicts' column displays "XYZ will be replaced" or "Create device" and does not "create a simulated device.
• If the Setup disk makes the SCXI configuration programmatically or an installer for the application, then more information about what is on the Setup disk would be useful.

Brad

• Need help to test the VISA interactive Control: Sorensen XBT32 - 3FTP USB connection problem

  Hello

  I use Windows 7. I installed the USB driver provided in this link:http://www.sorensen.com/products/XBT/XBT_Downloads.htm.

  Max is on the ASRL5: COM5 series & parallel in the Device Manager it is listed in the port: COM5

  I don't know how to test using VISA interactive control to ensure that the connection is established.

  Here are the parameters:

  Serial settings:

  Baud rate: 38400,

  Data bits: 8

  Stop bits: 1

  Parity: None

  I use the default settings for the other options such as flow control: none, Timeout = 2000ms etc.

  In the attributes view tab:

  Attribute: is the connected port

  Current value: error VISA: (Hex 0xBFFF001D) the specified attribute is not defined or supported by the referenced resource.

  I don't know if it's important.

  When I write * IDN? \n (bytes to read: 6), I return the Count: 6 bytes

  When I click on "Read Status Byte":, I get the following error:

  Error reading STB operation VISA: (Hex 0xBFFF003A) cannot start the operation because the installer is not valid (because of attributes defined in an inconsistent state).

  If I click on "Query", I get the following error: reading operation error VISA: (Hex 0xBFFF0015) timeout expired before the operation is complete.

  I also tried to create USB raw driver help driver of VISA Assistant. In this case I kept getting timeout errors: read operation error VISA: (Hex 0xBFFF0015) timeout expired before the operation is complete.

  Can you please tell me what I'm doing wrong?

  Thank you.

  Who cares about the number of bytes written? And configure the windows com port is not relevant. What is important is how you set the com port in the VI or max.

• PCI-1422 and RS 232 control of a camera Hamamatsu ORCA-HR (HR C4742-95-12)

  Hello

  I'll have some incompatible problems when I try to control a camera Orca-HR (Hamamatsu C4742-95-12 HR) via RS232.

  I have a feeling that the problem comes from how the RS232 port emmbedded (emulated?) in the PCI-1422 is used or recognized by the various software that I've tested.

  So first, this port emulated/integrated should appear in the series, Max & list parallel port? I don't think, but he's not here, that's for sure. I have 'only' the projection of card PCI-1422.

  Case where I can access some of the attributes (accessible from limited functionality) camera:

  -By MAX I can change some settings so the snapshots of controller and make.

  -I can access these functions by IMAQ ('IMAQ camera set attributes.vi', etc. see Appendix vi example).

  -J' have a full control of the camera via the Hamamatsu Hipic 8.0 software, but only if I use the internal drivers and a different com port than those incorporated in the card PCI-1422 (Hipic offers not only port com in any case perhaps because there is no by saying?)

  Case where I can't access the camera at all:

  -If I try to use VI to a Hamamatsu (the most recent in sample screws & DLL or older version), it does not work: calls to any function of the 'tmcamcon.dll' return errors, pointing to the fact that there is no camera detected: the first sub_Vi (tm_initialize.vi) will return no error but zero connected camera and other screws return errors saying there is no camera using this handle, or no camera can be activated at using this handle.

  -I have NO camera control via the Hamamatsu Hipic 8.0 software if I use the DCAM API drivers no matter what com port (incorporated in the card PCI-1422 or other).

  Does make any sense to you?

  I just thought that the Hamamatsu screws cannot access the camera via emulation RS-232 of the PCI-1422. Is there a configuration setting, that I could use to those who do work and do not have to restart from scratch with IMAQ and with only limited functionality?

  Thanks in advance for your answers.

  Hello

  In fact, you can have access to the serial port integrated on the PCI-1422 map only with IMAQ functions.

  This explains that you cannot see in the section "Series and parallel" in MAX.

  I have not really well know PCI-1422, but there's probably a way to access the serial port on the card PCI-1422 in MAX.

  Camera attributes, you are able to access with IMAQ, y then the camera assigns the has camera driver.

  If you are able to access more attributes with Hamamatsu driver, it is the manufacturer who decided to restricted access to other drivers.

  But if you are not able to use the screw manufacturer, you should probably call him to find out why it works badly. Perhaps a version control problem or a update of the firmware?

• Equium A200-15I - how to install more memory?

  My memory in my Equium A200 - 15I SERIES is at MAX, what is.

  How it came to new 2x1GB can these be removed and install more memory

  Hey hun01,

  I searched a bit using Google and the Equium A200-15I is equipped with an Intel 943GML chipset and this means that the laptop can use up to 2 GB of RAM (2 x 1 GB modules).
  If your laptop is already equipped with two 1 GB modules you can t upgrade it and if not you PC2-5300 modules to upgrade your laptop.

  In addition, you should also check the user manual where you can find additional information about it.

• For Satellite Pro M70-220 port replicator

  Hello

  I have a M70-220 and I need of series, parallel, and ps2 connections. I found this unit at Toshiba: PX1098E-1PRP - replicator USB 2.0 ports. My question is if it works with my laptop...

  Thank you.

  Hi Andrei

  One of my friends use the same USB port replicator with its Satellite P20 and M30x. I put t not see why it should not work with your unit too.