Toshiba screen power failure that cannot be repaired

Similar Questions

• I had a power failure that created a restart of windows vista problem

  I had a power failure that created windows error and cannot start my lap top. I understand that I must save the files & photos before trying to reload Vista in its original configuration... How do I go about backing up since the computer does not load...? How much does it cost if I'm looking for a specialist to backup?

  Hello

  power outages are often the cause of hardware problems

  You can try these methods to save the data

  1 slave the drive in another computer and try to read the data in this way

  2 buy or borrow a pregnant USB hard drive upgrade disk hard inside plug it into another computer and try to read the data in this way

  3. If your equipment is damaged by using Knoppix or similar CD linux to retrieve data won't work because they depend on your working materials

  Read about it, even if it's here

  http://www.Knopper.NET/Knoppix/index-en.html

  4 data recovery experts are very expensive

  You can always do a startup repair disk and try to start windows

  the link below is how to download and get a vista disk startup repair, which you can start from the

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  Here's how to use startup repair system restore command prompt, etc. to bleepingcomputers link below

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  to boot from the dvd drive to be able to you will see a way to get into the bios Setup at the bottom of the screen or command menu start

  It would be F2 or delete etc to enter the BIOS or F12 etc. for the start menu

  Change boot order it do dvd drive 1st in the boot order

• Scan of found corrupt files that cannot be repaired by SFC

  After problems with a recent update of windows which was followed by a restore failed, a black screen, then a system repair, I now have a number of corrupt dll files which result in "bad image" error messages when I start applications.

  This does not stop at the launch, but is an irritation!

  I ran sfc/scannow which reports corrupt files that cannot be repaired.

  I have a 'backup' restore point in 2012, if I restored it, it would restore these files corrupt, or the only solution would be to use my factory restore disk?

  Original title: rafeng

  You can have your problem of corrupted files, but do you know why the problem arose in the first place?

  Please provide a copy of your system information file. Type the system information in the search box above the Start button and press the ENTER key (alternative is select Start, all programs, accessories, System Tools, system information). Select file, Export and give the file a name noting where it is located. Not to place the cursor in the body of the report before exporting the file. The system creates a new information file system each time system information is available. You must allow a minute or two before the file is completely filled before exporting a copy. Please download to your OneDrive (formerly Sky Drive), share with everyone and post a link here. Normal mode preferred report. Please say if the report was obtained in safe mode.

  Please download and share with everybody fresh copies of your System and your event viewer on your Player Application logs One (formerly Sky Drive) and post a link here. You can delete the earlier copy of your OneDrive records.

  Please download and share with everyone your event to your OneDrive Viewer Application copies of your System and logs and post a link here.

  To access the system, log, select Start, Control Panel, administrative tools, Event Viewer, in the list on the left of the window, expand Windows logs and select System. Place the cursor on the system, select the Action in the Menu and record all events (the file default evtx type) and give a name to the file. Do the same for the application log. Don't provide filtered files. Do not clear the logs so that you have a persistent problem.

  For assistance OneDrive see paragraph 9.3:
  http://www.gerryscomputertips.co.UK/MicrosoftCommunity1.htm

  http://www.gerryscomputertips.co.UK/syserrors5.htm

• System File Checker detects files from oembios that cannot be repaired

  I ran the System File Checker on my computer Dell Dimension, and he found files that cannot be repaired: oembios.dat, oembios.sig and oembios.bin. The computer has Windows XP with Service Pack 3 installed and was purchased new in December 2002. The original XP installation disk that I've ever used, a SP1 is installed.

  Event Viewer gave this message for one of these files after run the System File Checker. "The oembios.sig of file protected system could not be restored to its original, valid version. "The file version of the bad file is 0.0.0.1 the specific error code is 0x800b0100 [no signature was present in the subject.]."

  Everything works well, and these corrupted files seem to have no effect on the operation of the computer. I even ran a Seagate hard drive diagnostic test, and it passed. These files, compressed copies that are in c:\i386 and on the installation disc, be repaired and properly placed in their place in c:\Windows\System32?

  Thank you, Robert. I tried your suggested solutions.

  First, I tried expanding oembios.si_ of the CD on the e drive (CD player) after the reboot. But I got this message from the command prompt: "cannot open the input e:oembios.si_ file."

  Second, I tried to develop oembios.si_ of the c drive, where I know it exists in c:\i386. Yet once again, I got the same message that the input file cannot be opened.

  This has proved to be a sticky problem. Fortunately, my computer still works well. It is just that I do not have corrupt files hidden.

• Aspire constant V5 - 571p blue screen-Geek Squad says cannot be repaired? New motherboard

  Help! I was told should buy comuter new can not solve?

  did not help much, but I think geek team has already found the culprit.

• ONS 15454 presents itself as 'unknown' after power failure

  We had a power failure that also landed an ONS 15454 in a remote installation. To restore power and power on the device, it appears in the CTC under gray with "Uknown2" as the name.

  I had someone reinsert the card of STC, but sometimes still unknown.

  Has anyone seen this? Suggestions (the unit is hours from me)

  Try to restart the session from the CTC and clear the cache of the CTC

  You can test the node

  Checks whether the node is in the OSPF routing table

  You can access through the CTC locally

  Your CTC terminal is directly connected, or does it go through a firewall

  Probably resolved now how did you solve it?

• Windows 7 starts problems with black screen and the cursor because of power failure

  I'm on a Windows 7 64-bit Home Premium OS. Start-up problems arose after the power failure (accidentally unplugged the charger, the battery was not in place) during a video call in Skype. Accessories attached to the laptop at the time were a Logitech Webcam, a dongle Bluetooth, microphone and headphones.

  When starting my laptop Asus N81VP, he'll go as far as the 'Starting Windows' logo, then I meet a black screen with a mobile cursor. I don't then right click, CTRL + ALT + DELETE.

  I tried the things:

  Start Up Repair = "cannot automatically repair."

  System Restore = no available restore points

  Windows Memory Diagnostic = at 100%, no screen of detected problems, then black with mobile cursor

  Networking Mode Safe Mode/Safe = black screen with cursor mobile

  Activate video low resolution (640 x 480) = black screen with cursor mobile

  Good known Configuration = black screen with cursor mobile list

  Start Windows normally = black screen with cursor mobile

  Please help me. I've had this laptop for less than a year, and it would break my heart to have to re - format.

  You seem to have exhausted most of the options available in such cases, except two:
  D ' log in under a different account.
  -To restore your registry files manually. See below for more details.

  On your heart that could get broken: have you considered using the imaging facility that is integrated with Windows 7? You can find it in the control panel / backup and restore. This is somewhat marginal in the feature and it can be finicky, but it saved my butt several times.

  You can restore your registry files manually to a previous point through the steps described below. The process is complex and requires some careful typing. Ask a computer-savvy friend to help you if you lack experience in this field. Note that it may reset your password to a previous value.
  1. keep tapping F8 during the first phase of startup.
  2. Select repair in the menu that looks like this:
  http://Windows.Microsoft.com/en-us/Windows-Vista/advanced-startup-options-including-safe-mode
  3 log in as administrator if you are prompted.
  4. Select repair when prompted.
  5. Select the command line in the menu that looks like this:
  http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7
  6. identify the correct drive letter for your Windows installation. It could be one drive other than c, but it will not X:. You do this by typing commands
  DIR C:\Win*
  Dir D:\Win*
  dir E:\Win*
  until you find the Windows folder.
  I'll call this "Q:" drive
  7 type these commands:
  CD /d Q:\windows\System32\config
  xcopy *. * Q:\MyRegBack\
  CD RegBack
  dir
  8. review the dates of the software, system, and SAM files. The files created before or after that is your problem?
  9. If they were made before the problem appeared, you can then type these commands:
  copy software / y...
  /y copy system...
  /y copy Sam...
  (the two points are part of each order)
  10. restart normally. If things don't work then you can go back by copying files from the original register of Q:\MyRegBack to Q:\Windows\System32\config.

• Computers that are affected by a power failure

  Last night while I was watching TV, the power went out just for a few seconds, then she came back. I don't think anything of it, but, when I went to use my computer the next morning, he was sounding like a war was going on inside. The only thing I forgot to mention, is that I don't always close my computer before going to withdraw during the night, while he was at the time of the failure. Something does not look good and he echoes and I can tell by the power button it seemed that it was not a fixed light, it vibrated. I just hope that it is something that can be fixed. The thing is, I intentionally used these power strips that the electricity company gave to those who wanted to conserve energy, and also I thought it was protected power strips. Now, if someone can tell me if there is a chance that this computer can be repaired and not corrupt, and the ability to fix it myself, maybe? I am at a loss without my computer, and the possibility to buy another is out of the question because I am on disability and I have no savings. Please, if anyone can help me with this one, I'll be very grateful. If there is an organization that provides computers to people in need, it would also be a blessing, or a place or a person who fixes them for a fraction of what the prosecution remains. Thank you, Christina

  Before you start worrying too or attempt to make any kind of troubleshooting, you should consider that the most common result of a power failure while a computer is turned on is nothing.

  This is particularly the case when the computer has not been used for awhile before the power failure.  It sounds like your case: you were in front of the TV and not to use the computer.  Depending on the configuration of your computer to the top, it's probably in standby or, at most, just sitting and idling.

  As a general rule, when a computer is not actually in the Middle using the hard drive, the most that will happen after a power failure is when the computer is next turned on, you will see a message that 'Windows was not properly shut down' and we'll give you a few options.  The option to choose from at the point is to 'start Windows normally.'

  After writing all this, please answer the following questions:

  1. When you first went to your computer the next morning, he was turned on or off?
  2. If it was turned off, what happened when you the activated?
  3. If it was on, click the Start button and turn the computer off (Shut down).  Wait for 2 minutes and turn it back on.
     • What is going on?
     • Windows comes up normally?
     • The computer always made strange noises?
       • If so, are the sounds of speakers or mechanical noises from inside the computer?
  4. What is the brand and model of the computer?

  If the computer is mechanical noises (I'm not sure what you mean by "sounds like a war was going on inside"), your best course of action is to turn off and take it to a computer repair shop local independent (not a chain of stores).  Too little likely, a fan — or worse, your hard drive - could have been damaged.

  Oh, and these power strips - insofar as they work - prevent power surges ' "(surge), no power failures.

• Error code 10 cannot install Maxtor 3200 after power failure

  Original title: maxtor 3200 code 10

  After a power failure cannot not re install Maxtor 3200 get response Code 10

  Hello

  The Code 10 error code is generated when the Device Manager has not enough information or error that spread upwards by device drivers is not recognized by Device Manager. In addition, this error may occur if one of the pilots who needs the unit does not start. If multiple drivers are used by a particular device, it can be difficult to determine which failed.

  I suggest you run the FIXIT from the link below and if it helps. You can also follow the manual steps and check.

  Description of errors related to the 10 Code that generates the Device Manager in Windows on computers

  http://support.Microsoft.com/kb/943104

  Hope this helps and keep us posted.

• This VM could not become vSphere protected HA and HA cannot attempt to restart after a power failure

  ESXI 4.0 3 running virtual machines.

  600 GB HDD / 8 Gigas of RAM / Xenon QuadCore.

  ESXI 5.5 (I had two).

  Using Raid 01 (1 TB)

  RAM of 64 Gbite

  Hearts CoreI5 Xenon proceso.

  VCenter server deployment with Vmware Storage appliance.

  Problem:

  I've had enough material resources, in fact, I had twice the disk space and memory to four times more in the reception of news

  When migrating virtual machines in ESXI 4 server and get Vcentener turn it on the message "this VM could not become vSphere protected HA and HA cannot attempt to restart after a power failure.  "

  I do not understand because the servers have resources, I can't find what is wrong.

  Should I use another method of migration?

  Once that you have migrated, can solve this problem without re-migration of computers?

  I found this post, but it's no imformation. This VM could not become vSphere protected HA and HA cannot attempt to restart after failure of.

  Thank you

  See:

  Re: This VM could not become vSphere protected HA and HA cannot attempt to restart after a power failure.

• There's the iPhone battery chargers 5 that use no electricity.  For use in a power failure.

  There's the iPhone battery chargers 5 that use no electricity.  For use during a power failure.

  Your best bet is an accumulator.  I have one I got on Amazon by EC Tech.  It is a brick, but it will charge my iPhone and the iPad, if the current is cut off.  You just need to load the brick and keep it in an emergency.

• Since the upgrade to 8.0, when navigation between screens, my computer screen becomes black for 1 second before the screen is redrawn. This happens regularly and is a major nuisance. It simulates a power failure. It does not happen with IE.

  Since the upgrade to 8.0, when navigation between screens, my computer screen becomes black for 1 second before the screen is redrawn. This happens regularly and is a major nuisance. It simulates a power failure. It does not happen with IE.

  Here I answer to my problem: I upgraded my graphics card and the problem seems to have disappeared.

• Satellite M50D-A-10Z cannot start, stuck on the Toshiba screen

  Hello

  I tried to install windows 8.1 after computer instalation. After this restart I can not do anything computer stuck on the toshiba screen (8 h), when I tried to turn on and go to the bios by pressing TAB computer stucks on bios Version screen and wont move :(

  Can someone help me! PLS

  To access the BIOS, you must press the F2 key immediately after pressing the power button.
  Is this possible? You can access the BIOS?

  The laptop seems to be sold without a preinstalled OS. How have you installed the Windows 8.1? Have you changed some settings in the BIOS?

• Hello, I receive a message telling me that my AC power adapter type cannot be accepted.

  A few days ago, I started having a power warning message when I turn on my laptop. It is said that the AC power adapter type cannot be determined. Beacause it my battery will not charge. But it's the power adapter that came with it and I have used for so long that I got the machine. Do not know what is happening.

  I guess that the laptop works on AC power only but always?

  If you remove the battery from the laptop work?   If yes then I suspect the battery does not have rather than the power adapter.
  If it will not work without the battery then I would suspect that the adapter is faulty/defective.
  Don't let not the battery-even if it is the problem.

• I try to send an email I get a message at the top of the screen actually say that Hotmail cannot process and suggesting I check my internet connection.

  My hotmail account is playing up - suggestions pls for the following scenario.  I try to send an email I get a message at the top of the screen actually say that Hotmail cannot process and suggesting I check my internet connection.  I check the connection and everything is ok.  I'm trying to move from one folder to another and sometimees I get the same message.  I delete the 'old' content and it reappears in the folder.  Everything is very confused.  Any suggestions please?

  Please try the Hotmail Forum http://windowslivehelp.com/forums.aspx.