Windows 7 starts problems with black screen and the cursor because of power failure

Similar Questions

• After logging on my Satellite Pro only black screen and the cursor are visible

  I have a windows vista pro (PSAASE-00G004GR) satellite after turn on and typing the password for windows vista, the screen goes black but I see that the cursor moves & because it seems that the hard drive also works in th background, but I can't see anything except the mouse cursor , I tried to boor with other options (LAST WORK safe MODE KNOWN FEATURES... etc) but it's still the same only black screen and the cursor...

  I do not prefer the product cause of my data recovery on this subject, any ideas?
  thnx

  Hello

  You have the Satellite Pro A100 PSAAS hmm if you want to save your personal data, I recommend to remove the portable computer HARD drive and try connecting it to another computer via an external USB HDD controller. These cases of 2.5 HARD disk are not expensive and you can buy it in every store of the computer.

  Then you could try to recover the laptop delivered together with the Toshiba Recovery CD.
  But wait; have you tried to connect the laptop to the external display?
  Check it!
  Maybe you could see something on the second screen.

  I think that this procedure could be useful to clarify what s wrong.
  To me this question looks like a small little dysfunction of the FL inverter.
  In this case the installation of the new operating system will help you not to solve this problem.

  But who knows the verification is necessary to find what could be wrong.

  Good luck and bye ;)

• Just bought a msi gtx 750 ti OC edition.when installed does not start, ends with a black screen and the cursor

  As indicated in the title, I bought a ti 750 gtx.

  N750Ti-2GD5/OC

  The machine had a 620 in gt and works very well with it in. When I install the ti 750 gtx, however, the boot system hangs on a black screen with cursor / underscores and a single beep.

  The system is a h8 1203, with a power of 460.

  I also have a gts 250, that also installs and works fine. Ive read a little, and there is a problem with this map and the hp system? something about the type of bios? I couldn't quite follow what has been said.

  Hello

  If you upgrade to Windows 8 (UEFI-mode Setup) and apply the BIOS posted updated so you should be able to work to the video card.

  Don't forget to create a set of external support of HP recovery before installing a new operating system.

• After using a third party partition manager program left to extend my Windows 8 partition, the system of Windows 8 start to a black screen and Windows 8 partition of the drive letter has changed

  Original title: problems of Windows 8

  I have Windows 7 (32 bit) and Windows 8 (64-bit) is installed in a dual boot. I tried to extend the partition of Windows 8 with a third party partition manager. Subsequently, I restarted after having learned so much.

  Later, the first thing I saw was that the locked screen image is replaced by a blue color. Photos of the user are also missing. Once connected, it took a long time for windows everything ready, and I'm stuck in a black screen with the mouse pointer.

  I entered in Safe Mode and found that the drive for Windows 8 letter has been changed (C: = Windows 7;) D: = recovery partition; E: = Windows 8, new drive letter; F: = Windows 8, old drive letter), I tried to change the drive letter, but it does not work.

  Partition of Windows 7 works well (it is what I currently use to put this problem), and I can access the data in the partition of Windows 8. I tried the methods of different repair without result (such as chkdsk and sfc/scannow).

  Can someone help me with this please? Any help would be appreciated.

  Hello

  I understand that you have a problem of black screen with Windows 8 and the drive letter for the partition of Windows 8 is also changed. This problem is due to the use of the third party partition manager program because it affects the registry files and causes the instability of the system.

  Try to run auto repair from the Windows recovery environment and check if that helps.

  Method 1: start the recovery environment with installation of Windows 8 media.

  It is another way to boot the PC and launch recovery tools when something goes wrong with the operating system.

  Please follow the steps below. Insert the DVD to install Windows 8 on DVD-ROM and restart your computer.

  (a) once you start your computer by using the Windows DVD or the system repair disc, a black screen is displayed with the gray text "Press any key to boot from CD or DVD". Press a button on any.

  (b) select the good time and the type of keyboard .

  (c) click on repair your computer in the lower left corner.

  (d) select Troubleshooting to Choose an option screen.

  (e) click on advanced options in Troubleshooting screen.

  (f) click Auto repair of Advanced Options screen.

  (g) following, choose the operating system by clicking on its button.

  (h) Windows 8 will be looking for problems on the hard drives and verify that all required files are intact.

  
  Method 2: Run the restoration of the system of the Advanced Options screen.
  
  System Restore to restore your computer to a previous state, quickly and easily without losing any of your files and personal settings. Sometimes when you install programs or drivers, they can affect some system settings and prevent other programs to function properly. You can use system restore to restore these settings to their previous state

  Follow these steps:

  (a) once you start your computer by using the Windows DVD or the system repair disc, a black screen is displayed with the gray text "Press any key to boot from CD or DVD". Press a button on any.

  (b) select the good time and the type of keyboard .

  (c) click on repair your computer in the lower left corner.

  (d) select Troubleshooting from the Choose an option screen.

  (e) click on advanced options in Troubleshooting screen.

  (f) select System restore.

  After the system restore your documents and files will always remain to their previous state.

  If you do not install Windows 8 media, I suggest you connect to any other computer and create a floppy disk to install Windows 8. Using this disk, you can run the troubleshooting provided methods.
  
  How to create the installation media for a PC refresh or reset:

  http://Windows.Microsoft.com/en-us/Windows-8/create-reset-refresh-media

  You can also try the same steps using the bootable USB key. You must select USB as the first boot to the BIOS device.

  Note: Microsoft don't recommend any third-party partition manager program because it corrupts the registry files and cause the instability of the system.

  Write to us if you're still having problems. We will help you.

  Kind regards

• Windows 8 black screen and the cursor after the connection

  Hello. I tried to upgrade to 8.1 Windows 8 Windows and it is stuck on like 3% for one hour, so I just rebooted the computer and he returned to Windows 8. I'm going to sleep and come back the next day and go on my laptop and it auto connects me and it goes to a black screen and I only have the slider on the black screen after login. I don't see the start menu, but I receive notifications for as sticky keys or any other notifications lights. I turned off my computer at least 20 times, took out the battery, empty the battery and tried to boot in safe mode with no luck. It is unlikely that it is an internal problem, because if I leave my computer alone for a few minutes, my screen saver photos appear. If anyone can help me solve this problem or help me get in easier safe mode would make things less stressful. I have an Acer Aspire V5 - 571 series. Thank you.

  Hi Roy,

  This problem may occur because of corrupted on the computer boot files.

  I suggest you to perform the checking and automatic repair if this solves the problem.

  If you do not have a DVD of Windows 8, I suggest you check out the link to see how to create an installation of Windows 8 media:

  http://Windows.Microsoft.com/en-in/Windows-8/create-reset-refresh-media

  Follow the methods suggested below:

  Method 1:

  Start on the recovery environment using the installation of Windows 8 media.

  Follow the steps below:

  Note: before proceeding further, make sure that the boot priority is set on DVD drive in BIOS. BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  • Insert the DVD to install Windows 8 on DVD-ROM and restart your computer.
  • After you start your computer by using the Windows DVD or the system repair disc, a black screen is displayed with the gray text "Press any key to boot from CD or DVD". Press a button on any.
  • Select the type of keyboard and good time.
  • Click repair your computer in the lower left corner.
  • Select Troubleshooting in choose an option screen.
  • In Troubleshooting screen, click Advanced options .
  • Click the automatic repair of the Advanced Options screen.
  • Then choose the operating system.
  • Windows 8 will then pick up questions on the hard drive and check that all required files are intact.

  If the problem persists, proceed to the next method.

  Method 2:

  Follow these steps to perform a system restore:

  • After you start your computer by using the Windows DVD or the system repair disc, a black screen is displayed with the gray text "Press any key to boot from CD or DVD". Press a button on any.
  • Select the type of keyboard and good time.
  • Click repair your computer in the lower left corner.
  • Select Troubleshooting in choose an option screen.
  • In troubleshooting screen, click Advanced options .
  • Select System Restore.

  For reference:

  http://support.Microsoft.com/kb/2756559/en-us

  Note: BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  Please let us know the results.

• HPE-500f freezes black screen and the cursor at the top left

  My Pavilion Elite HPE-500f boots up to a white screen with the cursor in the upper left corner. He will not start in safe mode. Problem started when I left flash drive in USB that may be a coincidence. Started from CD's with the recovery disk, but which did not also. Run diagnostic F9 of the opening screen and it shows the error message "test of startup failed: error code BIOHD3;" No leave actiive.

  I can get it to run by pressing ESC at startup and even if the start of the hard drive is highlighted I have to press down arrow for CD player, then the button to the hard drive, and press ENTER. It will start normally. This process works every time, so it doesn't seem like a hard drive problem.

  Appreciate any help on this forum

  Hello

  If you do not, use another PC to create a rescue CD Windows 7.  Download the ISO from the link below.

  Windows 7 64 bit

  You must use an app like ImgBurn to burn the ISO to a CD - a guide on the use of ImgBurn to write an ISO on a disc is here.  One time created, or if you already have this, insert the CD into the laptop and restart at the start of it.  Select repair.

  Select the "repair your computer" option and follow Option 2 in the guide on the link below to run the startup repair - you may need to run this 2 or 3 times.

  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  If the above does not help, take note of any error message you get during the procedure and include them with your next post.

  Kind regards

  DP - K

• Mac Pro black screen and the cursor on startup

  My Mac Pro won't start. He begins the start but stalls on a black screen.  None of the fixes recommended work (I tried them all THE). As I finally understood, it's el Capitan does not like more than one monitor (I have three). When I unplug the two monitors, it starts fine. Yosemite has worked well with three screens, ElCapitan started very well that if I unplugged one of you watching her. The latest version requires me to unplug both monitors so that it can start up.

  What specific Mac Pro?

  What specific graphics cards are installed?

  Are these Mac-Flash cards? They need additional drivers?

  How the monitors are connected?

• Satellite L300 - 1AP PSLB8E starts not--a black screen and blinking cursor

  I have a Satellite L300-1AP model no PSLB8E.
  While trying to do a system restore on it the screen became empty outside the slider, and that's how it remains.

  I can switch off and restart it, will begin to start, then exactly the same thing happening.

  Plesae any ideas?

  > pressing the zero key "0" turn on the power, when you see a white bottom bar and hear a glance release the Zero key and it should start installation or reinstallation of your system

  I doubt it will work because this function is NOT implemented on Toshiba notebooks European but as I know about the series of notebook Toshiba U.S.!

  You can try to press the F8 key. An option called fix my computer should then be visible. Select it, then choose Toshiba HDD Recovery. Then a HARD drive recovery procedure must begin.

  But if it of not possible to choose this option, and then you take your recovery disk and must try to boot from it.
  If you don t have a recovery disk, and then use a CD of original installation MS windows, or you can order a new disc of recovery from here:
  https://backupmedia.Toshiba.EU/landing.aspx

  Welcome them

• My computer has a black screen and a cursor and there is no menu start more

  Original title: replay Vista operating system

  What I would like to know, is my computer only has a black screen and a cursor, there is no menu start, so I can stop and start a new installation of windows vista? If anyone can help please. I thank you very much for your time and have a fantastic day. Shawn

  Hello

  What changes have been made on your machine for there to be a black screen with a cursor?

  Rather than doing a clean install of your operating system, I suggest you do the following.

  Step 1:

  Remove all external devices (printer, USB flash drive), as appropriate, and start your computer again and check.

  Step 2:

  If this is little help, start your machine in safe mode and check if it starts on the desktop.

  Let us know the status of the issue.

  Azeez Nadeem - Microsoft Support [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• Start the computer to black screen and the computer runs hot

  original title: sick Vista laptop

  My daughter portable computer began acting strangely very yesterday.

  Once connected, I get a black screen and a cursor.  The system seems to work at full speed, because I can hear the fan, and it runs very hot.  No matter how long it sits, the desktop does not appear.

  I can use Ctrl-alt-del to display the Task Manager.  The list of processes is limited to the process of the current user, and none of them use important CPU. If I click on 'See the process for all users', taskmanager freezes and I have to disconnect to get rid of him.

  Using the Task Manager, I can kill the process Explorer and then start it again, date at which I get my desktop.  However, it is still running hot and noisy.  With the help of SysInternals ProcessExplorer, there is no process using any important CPU.  Most of the time CPU is reported as inactive.

  I don't know what to think.  A boot loader took over the system?  A hardware problem?  OS corrupted files?

   

  Follow these steps to try to solve your problems of boot.

   

  Restore point:

  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/

  Do Safe Mode system restore, if it is impossible to do in Normal Mode.

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  http://www.windowsvistauserguide.com/system_restore.htm

  Read the above for a very good graph shows how backward more than 5 days in the System Restore Points by checking the correct box.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

   

  If restore work not and you do not have a Vista DVD from Microsoft, do a repair disc to do a Startup Repair:

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use:

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner:http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  See you soon.

  Mick Murphy - Microsoft partner

• Invalid product key, left my computer with a black screen and a cursor of the mouse on the boot.

  A few days ago, I tried to upgrade Windows 7 Home Premium (64 bit) to Windows 10 using the free update. Installation hung at 84% for 2 hours, then restarted, was unable to recover the installation and then could not get back to Win 7. This left us with a black screen and a cursor of the mouse on the boot. The computer would remain in this State for about 10 minutes and then reboot and repeat.

  Fortunately, or so I thought, I had a few CD Windows installation backup from the back to the era of digital river. So I thought I'd install fresh on my empty partition, copy my files and data, and then format the partition with the installation broken on.

  I did, but now he tells me that my product key is not valid and cannot be activated. The product key came on a real label on the PC when we bought it.

  The key is for X 16-96072. I installed X 17-58997 (Windows 7 Home Premium x 64 with SP1 (u)). I don't know what is the problem with the key? Should I have installed without the (u)?

  One key 25 digits grouped in 5 sequences of 5 characters not X 17-58997.

  To analyze and solve problems for Activation and Validation, we need to see a full copy of the diagnostic report produced by the MGADiag tool (download and save to the desktop -http://go.microsoft.com/fwlink/?linkid=52012 )
  Once downloaded, run the tool.
  Click on the button continue, after a short time, continue button will change to a copy button.
  Click the copy button in the tool (ignore the error at this stage) and then paste (with r-click and paste or Ctrl + V) in your message.

• When you try to watch tv in Windows Media Center, I get black screen and audio sometimes and sometimes does not.

  Black screen in Windows Media Center during the TV

  When you try to watch tv in Windows Media Center, I get black screen and audio sometimes and sometimes does not. Any fix for it?

  TV works on the other program I have and has been workign on MC last week, but now I don't?

  Some success with this issue (its OK, but BLACK) video for live/recorded TV

  ' 1) ' disabled ' tuner card (Ati HD 650 PCIe) TV [via right click] in the Device Manager
  (2) restart Win7 64-bit
  (3) Win7 located & reinstalled the drivers
  (4) VOILA!   Real video and audio live & recorded TV

  BTW - before above fix in Device Manager:
  Notice anything in his video & Game Controllers
  'Properties' reported 'this device is functioning.
  "Update drivers" reported "... software driver...»
  ... and no updates of WMC anywhere in sight

  Go figure!

• When I was playing the game and my 3D PC show the black screen and the sound of noise.

  Hi Admin,
  When I was playing the game and my 3D PC show the black screen and the sound of noise. And then I can't move anything and I can restart only. What is this problem? I don't know why? Please help me what should I do.
  My PC specs are as follows

  Aspire M5800 (Q84MR375) Genuine Windows Vista® Home Premium, 64-bit, Intel Core 2 Quad processor Q8400 (2.66 GHz, 4 MB L2 Cache, bus front at 1333 MHz), 3 GB Ram, 750 GB S - ATA HDD, DVD SuperMulti Double Layer drive, Nvidia GeForce GT220 graphics (1 GB dedicated RAM) card, Wireless LAN, keyboard and wireless mouse with LCD 23 '' monitor.

  phoechan,
  More than likely if this started after you upgrade to Windows7 then you might have to update your hardware drivers.  Go to the websites of the manufacturers of hardware for your PC and get all the latest drivers for Windows 7 (video, sound, chipset, etc...).  If they don't have Windows 7 drivers you may have questions until they create them.  You can also try to boot your PC and also right click on the game .exe file and change the compatibility mode to Vista or XP.

  Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• iPhone 6 alternating between the black screen and the Apple logo and nothing else

  my iPhone 6 alternates between a black screen and the Apple logo, what do I do?

  Hi Nathanielfromwa,

  If your iPhone 6 alternates between black screens and the Apple logo, this could be a problem that can be fixed by wiping your iPhone to factory settings. If this is the case, save your iPhone first. I've included links if you need help with backing up your iPhone, but also to reset to the factory settings.

  How to back up your device using iCloud or iTunes - Apple Support

  Erase content and settings on your iPhone, iPad, iPod touch or Apple Watch - Apple Support

  I hope this helps, and if you have more questions, do not hesitate to ask!

• Computer will not start with Windows. I get a black screen and a blinking cursor.

  Windows XP Home Edition startup problem

  I have Windows XP Home Edition, but the computer does not start at the top.  I get a black screen and a blinking cursor.  I have an XP installation disc.  I was in the Recovery Console to recover all of the standard tasks, but nothing helped.

  Brand, model and model number of your PC?

  Are you able to get into the BIOS?
  What took place prior to this problem?
  For now, you can read this to get some ideas:
  http://tips4pc.com/computer-problems/my-computer-boots-up-to-a-black-screen-with-a-flashing-cursor.htm