TouchPad overheating the Portege M800

Similar Questions

• On the Portege M800-11J SD card reader problems

  Hi all

  I hope that someone here will be able to help me with a problem. I have a new laptop Portege M800-11J and I try to use a 4 GB SD card in the embedded player. The laptop crashes and allow me to format the card or read. If I use a USB drive, it works without any problem.

  Through Google, I read that there may be problems with some drives and 4 GB cards.

  Anyone else has this problem or offer a solution? I did the driver regular re - installs etc.

  Thank you

  Adam

  What is an SD (FAT16)?

  Or is this a card SDHC (FAT32)?

  The M800 must be compatible with SDHC cards, so maybe it's a driver conflict. Or maybe the pins inside the drive is damaged and cause a short circuit.

  Have you updated the BIOS?

• No driver Vista Portege M800-105 (PPM81E) available

  Hello world

  I bought an M800-105 and as with all laptops, I bought I did a clean reinstall of the operating system (in this case vista Home premium)... to my surprise there is only one driver listed when I search model fo PPM81E vista driver (the driver Bluetooth stack)

  I downloaded the necessary driver as displays and pilot Wi - Fi intel.com but all the features of Toshiba as keys FN, webcam, touchpad buttons next to the... power button not etc don t market.

  The driver for the device will be published, or is there a mirror/alternate for pilots bond?

  Thank you

  Hello

  Portege M800 is, in my opinion, the most recent model Portege and will certainly offer the drivers. I think it's just a matter of time. Vista drivers are available for all preinstalled Vista notebooks and will be the same with the Portege M800.

  But one thing confuses me: why you installed your version of Vista if Portege M800 is already available with Vista Home Premium? You created the recovery DVDs?

• Portege M800: How to turn off the LED light of the multimedia and the touchpad?

  Hello

  I have Toshiba Portege M800.
  I want to know, how can I turn off the light of multimedia and the touchpad
  Thanks in advance

  Hello

  I m not M800 owner but I ve got an another Toshiba laptop and these LED lights I can turn market in the BIOS and in Toshiba HWSetup.
  The HWSetup is placed in Toshiba help optimize them and the settings are in the tab 'enlightenment '.

  See you soon

• Portege M800 - Touchpad light extinguishes, and comp slows

  I have a Portege M800, model PPM81C-05C020.

  My problem is that the light above my touchpad dims and then gradually turns off completely. When this happens, I can't use the touchpad. Fortunately, I have an external mouse plugged in, but when the Synaptics mouse turns off, it also slows down my computer. I type this post very slowly and it still takes forever for words on the screen to catch up as I type. I thought that maybe the driver was somehow defective, so I went on the Toshiba site and tried to download the driver for this series of laptop and then restarted, but it did not help. I ran various programs to ensure there is no registry errors, but they all come back clean.

  I don't know what to do. I brought to a place of computer before and they managed to fix it, but 2 months later, the problem is recurring. Help! : S

  Hello

  This driver you downloaded from the official website of Toshiba?

  I would recommend a driver update from the official website of Toshiba touchpad:
  http://www.Toshiba.ca

  And interesting to know what OS you have.

• Is possible to use the second HDD in PPM81E Portege M800-105

  Hello!

  Does anyone know, if it is possible to extend a Portege M800 - 105 model No. PPM81E with a second HDD?
  Is there a MediaBay for the DVD player to install a second hard drive?

  My goal is to use a Solid State Disk (64GByte) as the first disc (System only) and store all user data on the second drive.

  Best regards
  Sven

  Hello

  To my knowledge it is not possible to use a second HDD Portege M800.

  The laptop supports eSATA connection so you can connect an external HARD drive.

  Welcome them

• Portege M800: The fan is almost always on

  Hello!

  I have a Portege M800 M105 with Vista 64 bit. The fan is almost always on despite the fact that the temperature of the CPU is about 43 to 46 Grad Celsius and the CPU has nothing to do. I used the program Speedfan (http://www.almico.com/speedfan.php) to display the temperature. I find that the noise of the fan is very noisy.
  Is there a possibility to control the fan, so that it will be only noisy when the temperature is high?

  Best regards
  Sven

  Hello

  You are right. The Toshiba Power Saver for Win XP looks completely different as the Vista energy saver.
  But you can also change many settings in Vista energy saver that contribute to the use of the battery power decreases.

  The power settings are a bit hidden in the Vista energy saver but check this thread posted by Jayjay:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=38906&TSTART=0

  You will find a link to the doc of Toshiba:
  [How to manage Windows Vista power management features | http://aps2.toshiba-tro.de/kb0/HTD84026Q0000R01.htm]

  How to manage power settings in Vista there are has many useful tips.

  Hopw this helps.

  Good bye

• Portege M800-106 - bad quality by using the external monitor

  I use an external monitor LG Flatron L1811S on my Portege M800 and find that the image is not rock solid when I use the display on my desktop or screen of the M800.
  It is particularly visible on the big patches of color block where I can see shimmering light. I noticed that it's especially bad if I recently reconnected the laptop to the network after using on battery power until the battery is fully charged.

  This makes me think that the PSU interferes with the VGA output?
  Any ideas?

  Thank you

  To be honest I m more important lack of information in your ad.
  Are you using the native resolution - 1280 x 1024 / 75 Hz on screen?

• Portege M800 - the system hangs after connecting to fingerprint

  I just got my Portege M800 weeks ago and frankly speaking, this model has been giving me a lot of trouble. Earlier, it's heat problem in the palm rest and there is no solution for it.

  Now I am facing another problem with the connection of fingerprints. I'm running on Windows XP. I put the system must be locked after 5 minutes of inactivity. So normally after 5 minutes of inactivity, the system will have to be me to scan my fingerprint to open the windows. But there are moments which, after analysis of my fingerprints and put in correspondence with success, the screen will be just white (only show the desktop wallpaper). Not the desktop icons, no taskbar windows and nothing. Press Ctrl + Alt + Delete to bring up nothing and no answer even not a button. I tried to put the system to Hibernate by press the power button once as no response.

  So I have to finally press and hold the power button to reset the laptop.

  No matter which can help or give any idea of what was going on? Thank you!

  Hello

  I believe that these issues are in the past fixed with the new version of the fingerprint reader. Have you tried to install the latest version or you already have?

• Portege M800 - stop if I hold the grille left

  If keep my Toshiba Portege M800 by the section of the front left lower side, he sometimes stops...

  The power led (top left) is always on, as it is in mode 'sleep' but does not. The only way to start again is to hold the power button for several seconds, then restart

  Does anyone else have this problem? Is my laptop defective?

  Thank you

  Hello

  A friend of mine had the same problem with another laptop. If it holds the laptop or door to another place it completely freezes. :(
  He did send the laptop to an authorized service provider and they replaced the motherboard. A few days later he did return the laptop and everything was working fine again! :)

  So I think you should send it to an ASP too. If you n t know one, on the Toshiba site, you can search for the nearest:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported downloads & => find an authorized service provider

  Good bye

• Portege M800 - SSD, lag of 30 seconds before the start after POST

  I have recently upgraded to an Intel Postville's G2 X 25 - M 80 GB SSD and experience a second rule 30 between the BIOS POST (black screen) and actual boot from the disc. Support of the Intel says that it is probably a BIOS problem and that I should install the latest firmware, which I already did (4.80).

  System: Windows 7, 127-Portege M800-127 PPM81E M800.

  Hello

  I guess that this shift will be caused due to the BIOS test. After you turn on your laptop it checks internal devices like HDD/SSD, CD/DVD disk, CPU, RAM, etc. So some of the material was originally this delay, I think.

  If the latest BIOS can't solve your problem, it would be interesting to know what is happening with a SSD of replacement. Can you check that out, please?

• Portege M800-A312 can't play using the full screen

  I just bought the A312 M800 and found that I can not play games using the full screen. I already tried pressing Alt + Enter during the game, put "full screen" in the option game, change the display resolution same as game (800 x 600) resolution, set the Compatibility tab, etc.. But everything went wrong. All my games to the point in the middle of the screen with black background. Did someone knows how to fix this problem so I can play my games using the full screen?

  Have you tried a BIOS update and the latest graphics drivers?

  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp

• Portege M800 - Exposed sensitive Touchkeys does not work

  I am owner of the Toshiba Portege M800-105. Everything done his work. After 2 months working on it, my sensitive touchkeys exposed next to the POWER button does not work. After that I uninstalled 'Vista-value-added-package' everything works correctly. Why? Now my FN keys do not work or are disabled. Why?
  Before uninstalling the package, the first button next to the power button had to function to turn off the backlight of the Logo, the touchkeys senitive one of my touchpad. NOW he cut the sound! Weired fairy if you aks me. How do I challenge my buttons up to factory settings and make function keys FN?

  I reinstalled the value added package again, and have the backup problem as before: the first two buttons next to the power button does not work!
  Unter the Application: Thoshiba Button supports, for the first two buttons there are no keys depositd/marked so that I can change the configuration here.
  FN keys work after installation of the package, but not the sensitive keys! Please who can help me?

  Value added package has small programs. One of them is the Toshiba button Support. Walker I have uninstall it everything works. When I install it, nothing works.

  Thank you for the help on [email protected]

  Post edited by: Togan_1

  Hello guys

  This is really strange. I put t really know what happen on your laptops. The fact is that these buttons are controlled by the software. If I remember well he called support Button or a button control and she is part of the package of added value.

  VAP contains several different tools and utilities. When you remove the VAP, it will be removed the responsible application of the functionality of FN (Flashcards), and this is the reason why the FN doesn't work anymore.

  So, theoretically everything should be OK when you install PPV again. Again theoretically. Why you still have this problem I put t know and I don t believe that no one can say for sure. Maybe some registry entries are corrupted now? Who knows?

  I presume that you don t want to use a more radical solution and do clean install of the new OS, but it can certainly help. With own OS pre-installed (factory settings) everything works well again.

  In the end, I must say that I use Satellite U400 (similar to your Portege) almost 6 months now and all the buttons work correctly. I always use the Vista version and I n t made no changes. It works well.

• Defective screen on Portege M800

  I bought a PORTEGE (M800-107) in 2009 and before the expiration of the 3-year-old warranty (2012), the screen went black all the time.
  I sent it to the official service of TOSHIBA in Greece (called "IDEAL his '), who fixed it in about a month (and after two attempts).
  A year and a half later, the screen went black again. Now they ask me 500 euros for the replacement of the screen. Of course I won't give all these money.
  Portege was the 3rd Toshiba laptop, I used. I chose it because I wanted something powerful and professional. The irony is that the more expensive model has exploded sooner than the cheapest.
  However, it was the LAST ONE on your part.

  PS: in order to take my laptop (without attachment), I have to pay 30 euros for check technicians!
  Really, you know someone who goes to the service for fun? Or I am responsible for the failure of your model?

  Hello

  To be honest I m was really asking you this display problem. Portege and Tecra are the best notebooks of Toshiba business line and for years, they are known as products of high quality with the best material.

  Anyway, sometimes the best products have problems and be in trouble. Similar things happen with all technical products. I know that's enough damage and angry, especially in the time when you need your laptop.

  Maybe it sounds stupid now, but maybe you can buy view on your own and find someone who can exchange it for you. I did it for my friend a few years ago. We purchased watch on eBay and we exchanged it alone. Of course on our own risk.

  Bye and good luck

• Portege M800 no boot after BIOS update

  Hello

  I encountered some problems with my netbook (Portege M800-10W) after the BIOS update.
  The update of the BIOS program appears failed. Then my Netbook automatically rebooted and now I can't start my PC more.
  All the LEDs will light up but the screen remains black and after a few minutes, the beep 3 times (1 long, 2 cm) netbook.

  How do I restore the BIOS to the previous version (or plant)?

  Thank you.

  Adrien

  null

  Hi Adrien

  I think that Akuma is right. Your laptop must be verified by the service of Toshiba s. Let check your laptop and I hope they will help you with this.