TouchSmart HP Envy 15-j070us display is not touchfunction more

Similar Questions

• ENVY TouchSmart 15 - j134na: TouchSmart HP ENVY 15 - j134na display flicker

  display monitor began to waver a bit as he isset to 40 Hz and it is set to 60 Hz of course.

  It's like that in the programs, windows and ubuntu 14.04

  I do need to update the bios or something?

  Thank you

  Today, I finally got.
  I find it unhealthy to watch the screen at 40 Hz so reinstalled windows 7 x 64 again.

  The flickering started right after I installed intel driver hd 4600...

  After a full day of reinstall drivers intel and nvidia I finally got.

  The flickering starts when you Dim your monitor, so when it is set to 100% or 0% I did not flicker

• TouchSmart HP Envy 15-J104sa memory card reader does not

  I took delivery of a HP Touchsmart from Envy 15 - J104sa, running Windows 8.1 this week and the internal memory card reader does not work. It does not recognize SD cards (I tried more than one) and continues as if nothing has been inserted; Don't display an error message. The cards work on my previous HP laptop. The only way to get the laptop to show an inserted SD card is to run the driver software update (http://ftp.hp.com/pub/softpaq/sp63001-63500/sp63415.exe) whenever an SD card is inserted; This must be done with the card in the reader. If the software is running and then the card nothing happens. If the card is ejected and then re-inserted (or a new card inserted) it is not recognized and the process must be restarted and the driver reinstalled even though nothing has changed.

  Can someone please help me with this question or I'll have to go back to the HP laptop. I do a lot of photography so being able to read fast and reliable SD card is extremely important for me; It is not a problem, I was expecting a new laptop all right out of the box.

  Thanks to you all.

  Unfortunately not, updates of driver solves the problem, but an update of the BIOS through the HP helper application seems to have resolved the issue. While I appreciate there were not specific drivers available in my opinion, it is difficult to accept that HP should be able to release a model where they know the equipment are not fully supported by the operating system and in this case does not work.

• HP Pavilion TouchSmart 23-f280: No. Intermittent display problem

  Hi guys,.

  Need your help with this new pc HP Pavilion TouchSmart 23-f280d all-in-one desktop PC.

  all newly purchased this product and had no problem to display but not to start the computer. It will happen only once I used as watch videos or whatever it is around 10 minutes to 20 minutes and the display will be switched off the sound always playing in the background. Later I just be like around a few minutes, then it will be back to normal. but sometimes, when this problem occurs, I tried to leave about an hour but goes blank display.

  Please help me to get the solution on this issue.

  Hello @ali_je24,

  I understand that you have a display problem intermittent with your new HP Pavilion TouchSmart 23-f280d all-in-one desktop PC. Please contact our technical support at the 800-474-6836. If you do not live in the United States / Canada region, please click the link below to get help from your region number. http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html. As with any new unit you want to ensure that all issues are dealt with properly and that they are properly documented.

  I want to thank you for display on the HP Forums. Have a great day!

• Want K203TX: Display will not wake up

  This is a new laptop.

  I did nothing about it, other than updates of Windows install and create recovery discs.

  • I put the option "turn off the display of" 1 Minute.
  • IMPORTANT: I put the brightness screen completely to zero, the lowest setting possible, by using the keys on the keyboard or the brightness option in Windows.
  • Let the laptop computer idle for a minute, the screen can accommodate as it should (the laptop is put to sleep after 30 minutes, only display that sleeps, the laptop is still awake).
  • Move the mouse, press the keys on the keyboard, the screen doesn't come back to the top. The computer is still in place and in the course of execution-i can switch keyboard backlight On / Off with the keys, but the display will not wake up.
  • Press on the "brightness +" button on the keyboard, the screen wakes up. It is the only way to wake up. The other option is to press on and hold the power button, force a stop down and restart the computer.
  • This occurs ONLY when "brightess" is set to the lowest level. If the brightness is set to again one level above the lowest, the issue cannot be reproduced. Move the mouse or press any keyboard will wake up the screen in this situation.
  • The two graphics Intel HD 5500 and GTX 850 M drivers are up to date.
  • BIOS is updated as well.
  • Battery / sector makes a difference. If the display brightness to the lowest, the screen will ALWAYS fail to wake up, regardless of which power source is being used.

  What should I do? Please don't tell me this is a minor problem and I have to live with it.

  There are so many problems minor with this laptop, and all these add make a total piece of cr...

  My almost 5 years probook with a second generation core i3 processor and no discrete GPU is better than this all-new 5th generation core i7 + laptop GeForce GTX.

  I'm starting to regret this purchase. I should have gotten another probook. Thought that offers want a better "bang for the buck", and now I think it was a huge mistake.

  Anyway, no idea how I can get this fixed? Looks like a right driver problem? Or is this a hardware problem? Can we with a trial of mobile Envy this out and tell me if the problem can be reproduced on their platform? It cannot be reproduced on my Probook.

  Thank you.

  Hi @johnwinchester,

  I'm so glad to hear you're solves the problems you had! The key is that you are now without a problem.

  To answer 2 questions;

  1. to my knowledge, if you purchased the HP 3 year extended warranty on the spot with a cover against accidental damage, then it usually starts from the date of purchase. Be sure and check out I would suggest either go this site check your product warranty and/or contact us.

  2. I'd say creating new recovery disks. The old drive will not help to you on your product. You have the ability to create new disks of recovery of the product without any reported problems. I wouldn't take the chance, I just came out with the old and turned to the future.

  I hope this has helped!

  Have a great day!

• Equium A300D - 16 c - display does not

  My girlfriend has an Equium A300D - 16 c which had some problems lately.

  In recent months, whenever she turns on the system, the display does not pull upwards and it takes several tent for lights.

  The strange thing is every time that happens, the system boots normally always that you can hear the Windows 7 startup sound.

  I'm looking for in this question for some time now and I'm running out of ideas.
  Initially, I thought that it could be a wiring problem but by stripping the laptop down, I found that the cable was still firmly in place.

  I also tried to remove the RAM, HARD drive and DVD drive, but it still doesn't pull upward. On the odd occasion she started upward when you do it, but after restart, it has not started again.

  I think that this could be either a transmitting power or the mother board is on its way. This problem has worsened gradually (it took more than 20 attempts it turn on and off this morning) so finally he come not at all.

  To clarify, the system will start after several attempts, but most of the time that the screen not turn on (not even the backlight). It works with an external display on the HDMI so the GPU works.
  I tried to keep the power with no energy source button to unload the system, but it does not help.

  I also noticed that if you hear it boot and close the cover, the reopening of the display lid will come on but with the bad (1024 x 768) resolution that has intrigued me even more.

  Any ideas on what could be the problem? I would repair it rather than just buying a new as its still a decent system apart from this problem.

  > To clarify, the system will start after several attempts, but most of the time that the screen not turn on (not even the backlight). It works with an external display on the HDMI so the GPU works.

  This means that you can use the laptop as part of the external screen, but it does not work with the internal screen?

  This means that the internal display module isn't OK. It probably needs to be replaced.
  But this does not explain the problems while turning on the laptop.

  In the worst case the mother for laptop AND the internal screen are affected, but it would be really strange and rare bad luck

• updated my iPad to 9.3 air activate iPad display does not not my account information, but the Mac computer accepts my Apple ID and password

  updated my iPad to 9.3 air activate iPad display does not not my account information, but the Mac computer accepts my Apple ID and password

  A lot of people is affected by this problem, and Apple has worked on the issue.  Some found the following steps useful for this issue:

  Go to iCloud.com and select settings once you are connected.  Click on your device listed there and remove them from the account (not typing not erase or lost mode).  Restart your device and must ignore this lock of Activation screen because you actually disabled the lock by removing the device for iCloud.com

  I hope that helps!

• try to install GEFORCE GTX650 in my HP Pavilion p6 - 2413 has but the display will not illuminate.

  Try to install the GEFORCE GTX650 in my HP Pavilion p6 - 2413a, I plugged everything in and the fan seems to work but the display does not illuminate.

  There is another cable with 2 multi 1 6 end plug but I can't work out where to connect.

  I tried to find it on youtube but can't see where he's going to help me please.

  Hello

  You need a greater power to support a PCI-E power connector 6 pin. Try a Corsair CX500, or CX600. The image below is that of a NVIDIA GTX 650 which shows where to connect the PCI-E 6-pin connector to the graphics card.  Most of the HP PC which have a greater power or 460 watt have they support for the PCI-E power connector 6-pin.

  

• Download StarWar 6 pack - I get "movie will play not display does not support HDCP" I have a MacBook Pro '11 '.

  How to play movie with HDCP?   What is it?  Why he won't play on MacBook Pro 2011?

  Hello TheBell,

  Thank you for using communities of Apple Support.

  I see you found a mistake that "movie will not play, the display does not support HDCP" error when you try to play a movie downloaded on iTunes. I have a couple of things I would like that you try to refine the question.

  First, start your computer in safe mode and test the question.

  Try safe mode if your Mac does not end commissioning

  If after the test in safe mode, the issue is still in progress, and then create a new user and test in the new user.

  OS X Yosemite: set up users on your Mac.

  If you still have questions, additional information would be useful. Using an external monitor? If so, test with just the internal display on the MacBook Pro. All the other things you notice?

  Best regards.

• IdeaPad P400 - display does not work.

  Hello, I have a P400 Ideapad, display is not working properly, it will stay black. But if I move the screen forward or backward, it works again, as if she had a bad connection.

  Especially if I'm pushing on a corner of the laptop, it works perfectly.
  Can you help me please? What can be?
  Thank you in advance!

  Finally I took it for repair, he was be a defective screen, got a new.

• Thunderbolt 10 Windows display does not work

  Hello

  I'm trying to implement the following configuration:

  I have 2 Macs:

  • Mac Mini (late 2014, 2.6 GHz Intel Core i5;) Intel Iris 5100 1536 MB) with Windows 10 (Home) installed through Boot Camp
  • 27 "iMac (late 2013; 3.5 GHz Intel Core i7;) NVIDIA GeForce GTX 780 M 4 GB) installed with OS X El Capitan

  I want to use the iMac as a display for the Mac mini, but it seems that thunderbolt display does not work (I can not upgrade to Windows 10 by pressing Cmd + F2)

  Could you please help to solve this problem?

  Kind regards

  Dmitry

  Please see use of your iMac as a display with the target - Apple Support Display Mode and Thunderbolt Firmware Update 1.2: continues to reappear and ports Thunderbolt and the target Display Mode may not work - Apple Su... .

  If command-F2 does not work

  If your iMac won't go to the target Display Mode when you press Control-F2, check these things:

  • Make sure the iMac that you try to use it as a screen that supports target Display Mode.
  • Make sure you are pressing Control-F2 on the keyboard which is connected to the iMac to use as a screen.
  • In the keyboard system preferences, if the check box is enabled to use all F1, F2, keys etc. as standard features, changes of command-Fn-F2 key combination.
  • Make sure that your Mini DisplayPort or Thunderbolt cable is connected to both computers.
  • If you are currently connected to the iMac, you want to use as a screen, try to connect to return to the login window. Then again press Control-F2.
  • Some old keyboards Apple and third-party keyboards allow may not control-F2 to toggle display modes. In this case, use the keyboard that came with your iMac to activate / deactivate the target Display Mode.
  • If your iMac is currently started in Windows, it will not be in target display mode. Target display mode is not supported in Boot Camp.

• Display Clip not as bright as the black clip of money?

  My Silver 4 GB Clip arrived today ' hui - I flashed by (. 30) firmware and I noticed that the display is not * nearly * as clear as the display on my 2 GB Black model (same firmware).

  Both Clips are of type V1.

  Display on the silver model looks no brighter than the display on my expresses (nowhere near as bright as the Clip black model).

  Is this normal? (Is there some kind of filter on display on the silver model Clip and expresses it?  I * think * I remember reading somewhere that there is some Sansa players with a filter/coating anti-reflective (or reflective?) on the screen, but don't remember the details.)

  I guess I can share plates with one of my ten $ 1/GB refurbs I bought for parts a year from now when the warranty expires.  Heck of a PITA to have to squint at this screen dim pimped out for a year, however.

• SCREEN NOT COMING (display does not)

  Dear team

  Display does not come in my notebook whenever CapsLock light and light flashes, dealership also checked his RAM, but according to him, it's a problem internal, although wanting to take the necessary steps on an urgent basis

  Serial No. =[personal information deleted]

  PRODUCT C8C11PA #ACJ

  MODEL = HP 2000-2209TU

  [Personal information]

  1 flashes per second means CPU issue. You can have it fixed HP services.

  HP services will replace the right and exact part for this laptop.

  Having repaired with other technicians, I'm not saying that they are not good but that there could be a risk of other future issues.

• My Z5 dual display does not turn off automatically

  The screen does not turn off automatically even after 7 straight hours!

  As, when I charge the phone, the lids of the screen upward because of the notification but it does turn off the display automatically even after more than 10 minutes.

  I leave the phone at home (100% battery) and arriving at the House, after 12 hours later, the screen is still the battery drops to 30%. It drains my battery so.

  At least I have the display off by pressing the power button / etc, the screen does not turn off automatically.

  I tried to change settings in 30 seconds and 1 minute and others, but the settings do not seem to.

  Please help me solve this problem. Thank you.

  A third-party application is causing this behavior, either the app, an app that you downloaded, you'll need to uninstall a

• TouchSmart 300-1125 (Jesse APP78-CF) do not start BIOS

  Hello

  I have a HP touchsmart 300-1125 with windows 7 64 bit, version of the motherboard is APP78-CF Jesse.  I can't even start the BIOS!  Can someone help with this at all?

  Thank you very much

  Hello

  You say that you can not boot to BIOS, but are you able to get into windows or not?

  Your text, I think you have more problems then the startup in the BIOS, surely you can not even go to windows, I'm wrong?

  If this is the case, if you turn on the device and you have a black screen, you probably have a problem with the mother/CPU board, and they could be replaced.

  If you have knowledge or someone who can help, you can do a power reset first, remove the AC adapter and press and hold the power button down for 30 seconds, then try to connect to the device.

  If this is not enough, make a memory reset, remove the memory module, insert it on an empty slot and try to start the machine, if nothing happens, try to start unity wihtout the memory and see if you beep codes.

  If this is not enough, one thing you could try would be a reset of the CPU, but that one is a process more complex.

  Give me more deails, and we'll see what it is, so to provide more details and confirm if I'm right about your problem, if not, provide more details and we can check if the steps that I have proposed, can be applied by you.

  Thank you