Transfer of poor LAN WRT54G

Similar Questions

• Windows Home Server + Config IP/LAN WRT54G problems

  Hello

  I tried to fix this for days now, and I feel more I read on questions from other people who appear to be similar (at the beginning), I realize that I don't know even where to start... [: Confused:]

  What I know:

  I can't access my Windows Home Server from outside my home network. Whenever I have try and enter the domain name, setting Page of the WRT54G (identical to display when you enter http://192.168.1.1. inside my network) is displayed. Seems I found a way to configure my router remotely - but it's really not what I want... I rather like to access my home server, but it does not work. My LAN, I don't have a problem to connect to my server via remote desktop, but not from outside.

  I'm sure it's a (simple?) Number IP/LAN, but I just don't know how to solve. I know that something is obviously wrong with the IP addresses, but I don't know which ones to change without messing up my network, server, router etc...

  My presentation of Setup/settings:

  1.) WRT54G (v6) installed with latest firmware. Active DHCP.

  2.) HP MediaSmart Server (running Windows Home Server 2003) is configured with a static IP address > TZO domain name.

  3.) WRT54G Port Forwarding: all need ports (80, 443, 444, 4125, 3389) passed on to the Home Server (192.168.1.222)

  What strikes me (as shown in the tab "Status" of WRT54G):

  The IP address of the router is the same as my domain TZO address... is that supposed to be like that? -Need help, Pleaseeeeee!

  Q1: How can I access my home server from outside my network without pulling up the configuration of my router settings?

  Q1: which of my IP addresses & settings need to be changed... and where?

  Any help is appreciated...  Many thanks in advance!

  Armin

  Simply turn off remote access of configuration on the router or change the port that it sits on.

  The problem is that the web INTERFACE of configuration for the wrt54g is on port 80, so when you try to access port 80 (internet) outside it goes directly to the configuration UI instead of the server on port 80.

  Don't ask me where it is that I do not run firmware factory on wrt54g nmy.

  Concerning

  Fred

• Re: Files + LAN + Store TV + transfer = error

  I can't transfer files using LAN wired connection!
  I use Windows 7 + dlink router.
  When I navigate to the folder of the manual there is nothing inside, no manual!
  I bought the unit two days ago and I m so sad aboud it :(

  I can't believe I can't transfer files from my pc to Stor.e TV + camera...
  The device really sux. Amazing!

  :(

  I imagine that you are angry, but I want to know is follow:
  You have to get some info on this unit to the internet?
  Have you checked the user's guides document?
  You can download manuals from http://eu.computers.toshiba-europe.com/innovation/download_manuals.jsp?

  Please check it out and maybe you'll find some useful information how to proceed.
  Maybe you do something wrong. Who knows?

• How do I an E4200 with a WRT54G cascading

  I read this article and I am new to this, so...

  http://www6.nohold.NET/Cisco2/UKP.aspx?pid=80&VW=1&articleid=3733

  I'm trying to go the E4200 cable modem > LAN > WRT54G then Wifi with the same SSID as the E4200 to reinforce the range.

  E4200 is set at 192.168.1.1

  WRT54G is set to 192.168.1.2

  How LAN Port connect the LAN on the WRT54G?

  So, how can I configure the WRT54G for DHCP, SSID, password...  I use WPA for security.

  Here is another article that could be useful.  Basically, you have an ethernet cable from 1 of the 4 ethernet ports on the e4200, that connects to one of the 4 ports ethernet on the wrt54g.

  You must disable dhcp on the 54g (all addresses will be ' awarded by the e4200") the 54g must be assigned an address outside the range of addresses dhcp on e4200.  SSID and paswords should be the same on both routers.

  http://www.geektonic.com/2007/06/how-to-Setup-2nd-router-as-access-point.html

• WRT54G v3.1 (firmware v4.21.1) is not route packets between interfaces

  I am at a loss, because it seems that I'm really close to having my small network of installation works, except my router linksys faithful does not seem to be interested in packages of brewing between the WAN and WLAN interfaces.

  Background:

  I just moved into a new House, AT & T U-verse is taking their sweet time thought of digging a trench, so I have no wired internet, but I have a phone with 4G support that I can use as a hotspot Wi - Fi (high-end and very limited functionality).

  My goal is to rebuild my local network (two servers by cable, half a dozen various wireless devices), using my WRT54G as the central routing for her component.

  Plan:

  1. install a wireless bridge that connects to the Wifi 4 G hotspot.

  2. connect ZyXel bridge to the WAN port on the WRT54G

  3. connect and other devices in LAN WRT54G and wireless interfaces.

  Results:

  1. I got a ZyXel WAP3205 to this effect, and it seems to work fine (when connected to PC, PC is to get internet access through it perfectly.)

  2 seems to work fine. the linksys router is able to obtain an IP address on DHCP 4G Wifi hotspot (the Zyxel will exercise a passthrough.) The admin/diagnosis tab let me DNS resolve/ping/traceroute arbitrary sites on the internet.

  3 is not happy. I am able to access the router admin page. I can ping the router from any of my devices to end IP addresses, but nothing goes further. I can not ping IP of 4G Wifi hotspot for example (but I do go in the WRT diagnostic tools)

  Details of config:

  -4G - Wifi hotspot is configured as a DHCP/Gateway server. His IP address is defined as 10.10.10.1, subnet 255.255.255.0, assignment of IP addresses between 10.10.10.2 - 10.10.10.254

  -WRT router is configured as a DHCP/Gateway server as well. Its local IP address is set as 192.168.1.1, subnet 255.255.255.0, IPs assignments between 192.168.1.2 - 192.168.1.51.

  -All the rest is to default settings. Mode of operation is the gateway, routing table is showing

  Destination LAN IP.  Subnet mask |  Entry door |  Hop count | Interface

  192.168.1.0. 255.255.255.0. 0.0.0.0. 0           | Wireless LAN &

  10.10.10.0 | 255.255.255.0. 0.0.0.0. 0           | WAN (Internet)

  0.0.0.0             | 0.0.0.0. 10.10.10.1. 0           | WAN (Internet)

  This seems reasonable.

  -Status/router tab displays an IP WAN address 10.10.10.172, subnet 255.255.255.0, gateway 10.10.10.1, DNS1 10.10.10.1, which looks very good as well.

  I tried to adjust various settings on the router (gateway in router mode switching, disable DHCP and manually configure IP addresses), but nothing seems to convince the router to start, you know, routing of packets autour.

  I hope I'm missing something stupid here, and I'll be grateful for any help and judgment on this.

  Thank you

  Henri

  * Edit: I should add, I use this little guy for years previous houses, and it has always worked, even if its WAN port was always plugged into a modem cable of some sort. So I don't think that the WRT54G is likely to be broken or defective.

  Sonuva...

  Apparently, the little box just need a fast walk. After a factory reset and set my wireless settings screw, it seems to work perfectly.

  Well, I think that I'm talking to myself now.

  Just for fun, here is the great link, I'll be sharing between devices 8 or 9:

  

  (which is through my whole setup, even if the speed is exactly the same thing with a direct link.)

• Then the computer file transfer goes into sleep mode

  Original title: stop windows sleep/hibernation

  I need to transfer files from my PC to laptop. However when idle and waiting transfer via network lan my laptop will be slowed down and complete the connection. How can I stop this? Running Windows 7

  Hello

  
  Perform the steps to disable sleep and hibernation below and check if the problem persists.
  
  a: start Power Options of Type in the search box and click on enter.
  b: Now click on change plan next to Balanced (recommended) settings.
  c: now click on change advanced power settings.
  d: Now, Expand sleep option and then under sleep after and Hibernate after, set this parameters Never
  e: then click on apply.
   
  Also check out the following link
   
  http://Windows.Microsoft.com/en-us/Windows7/sleep-and-hibernation-frequently-asked-questions 
  
  Hope that helps.

• Real-time TCP/IP communication

  Hello

  I use the following materials:

  SMU-1062 q

  SMU-8108

  OR PXI-5600 (02 card for 40 MHz of bandwidth)

  SMU-5641R (two entries are used; one for each NI PXI-5600)

  PMA-1115

  LabVIEW 2009

  I use the mode of the instrument to detect the signal to jump and write in a spreadsheet in real time.

  My question is that how can I transfer data on LAN in real-time to create a waveform in software on a remote computer before writing it to the worksheet.  I'm looking for something like the time communication real TCP/IP. I enclose my VI. Kindly guide me that how can I do this?

  Thank you and best regards,

  Rashid

  Hey Rashid,.

  Check out this tutorial with examples and let me know if it helps.

• Installation of two - route

  I live in a rural area and have the two satellite internet and cellular (mobile broadband) internet, because none are reliable. I connect to technology mobile broadband with a PCMCIA card that is inserted into a Linksys WRT54G Router. Until very recently, I plugged on satellite via a separate router, which meant that I had to switch routers to switch services and one of the two services could use both.

  I just bought a router Linksys RV042 double-Wan, hoping to run them simultaneously by satellite and cell phone through the same router and use load balancing. I have the RV042 defined as the router DHCP. DHCP is disabled on the 54G. I changed the IP address of the default 54G to 192.168.1.145, in the sector of the RV042 customer. I connect a LAN on the WRT54G port to a port on the RV042 WAN. No go. The RV042 does not see the 54G. He treats the LAN connection as active, but does not have an IP address.

  How can I get the RV042 the 54G, as he would a modem? Any ideas?

  It's a bit complicated, so I have it divided into stages.

  IP address settings:

  (1) the value of the port LAN WRT54G 192.168.2.1

  (2) set the RV042 LAN port on 192.168.1.1 [default]

  (3) RV042 WAN1 and WAN2 for obtain an IP automatically

  (4) WRT54G LAN Server DHCP active.

  (5) WRT54G gateway (no RIP) mode

  (6) set RV042 for BACKUP or load balancing mode as you wish

  (7) fill RV042 configuration of DHCP - DNS Server - with 192.168.1.1 or the address of an Open DNS server that is accessible from both of your ISP.

  Connections:

  (1) WRT54 LAN to RV042 WAN2

  (2) RV042 WAN1 to satellite Internet

  (3) PC and any other printer, etc., next to RV042 LAN game consoles.

  Results:

  (1) WRT54G should now be accessible [of LAN] to 192.168.2.1

  2) two providers of Internet services must be accessible without the need to reconfigure the hardware or the LAN IP settings

  (3) RV042 is accessible [LAN] at 192.168.1.1

  (4) all connected to the WRT54G wireless LAN devices will not be able to access the Internet by satellite.

  What is the kind of Setup you had in mind?

• Local Access Mode - manual removal via WAN connection

  I would like to set up local access to some desktop computers, but want to use the option of manual control (pg 254 of the admin View 4.6 guide) I released the base image which was published on the forwarding server, but when a user try to complete the payment process they get the error "a connection to the forwarding server could not be established. Please check your network settings. They are able to see their jobs right and that it points to the base image they received via other channels of distribution (and not directly from the servers of the view)

  My security server firewall is configured to allow the ports on the JMS, JMSIR, AJP13 connection server, http, https and PCoIP but how to configure the forwarding server to adapt to configuration or are there alternatives to opening ports on the server to transfer inside the LAN of business if I want to just use it for access in local mode

  Hi Mobcdi,

  Option 1 (tunnel) description says "network traffic is routed via the view connection server or a server security if one is configured."

  Sequence - 1 is seems more correct, but with slight modifications.

  Form SS must be a SSL connection to TS, because all local traffic is routed directly between the SS and TS

  Firewall rules of back-end on Page 61 of the www. VMware.com/pdf/view-46-architecture- planning.pdf said

  "If you configure the connection to the server display to use SSL for operations in local mode and office supply, security servers using port 443 for downloads and the replication between the local mode desktops and server transfer."

  -noble

• Copy 700 GB of virtual machines directly to ESX 4.1 data store

  Hello community,

  We have a bunch of VMS (~ 700 GB total) stored on a drive of 1 TB and we would like to copy them directly into an ESX 4.1 data store (located on an EMC Clariion CX4-120).

  We do not want to transfer via the LAN - not an acceptable solution.

  However, the Console of Service of ESX 4.1 does not seem to allow USB drives be mounted (I searched the Internet, asked some contacts of VMware, doesn't seem to be implemented/supported more).

  Possible solutions:

  1) we installed a W2K8 R2 physical server that has access to the San, but apparently, there is no reading + writing drivers for Windows (data warehouses) VMFS volumes

  2) perhaps to reinstall this physical box with a Linux who read + write drivers for VMFS volumes?

  3) reinstall the physical box with VMware ESX 3.x Service Console allows installation of USB drive? But it will be able to see the data created by ESX 4.1 stores?

  Thank you for your valuable contributions.

  Cyril

  No probs Cyril - easy to use - you should be fine!

• Satellite Pro A110 crashes during the transfer of the large data in LAN

  Hello

  My Satellite Pro A110 crashes during the transfer of the large data in LAN. The network driver is a Realtek RTL8139/810 x Family Fast Ethernet NIC I've been looking through this forum and found some wire whit exactly the same problem, saying that the solution is to update Realtek lan set up in BIOS, not the computer BIOS, but I can't find any link to download the necessary upgrade file. Can anyone tell me please where to find this upgrade file or send it to me directly?

  Thanks in advance

  Is - this transfer of data in the company where you work? Do you want to download data from the server, or how to understand this? How to understand what you mean under big data?

  Have you tried downloading data on the Internet? For example, if you try to download some trailer HD (more than 200 MB)?

• I have an 802.11n wireless Lan card and the strength of the connectivity is poor however my laptop compac has excellent connectivity which can do to get a good signal

  I just bought a new PC (foxconn) who has a 802.11n wireless Lan card, my connection is very poor but my connection on my laptop compac and iPad are excellent. Is there a way I can get a better connection with this lAN card?

  Hello

  Check with the assistance of FoxConn, their documentation and online drivers. Don't assume new products
  have up-to-date drivers.

  Are all Windows 7 computers?

  The router may also need a firmware update so check with its creator.

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• WRT54G ignorant transfer

  I have disabled the Windows Firewall, I have no firewall protection or the third-party virus. I put my computer to DMZ... aaand I get ports 135, 139, and 445, and that's all!

  I have even passed and unDMZed and transferred ontop of DMZ, nothing. Public static or unstatic.

  My WRT54G is V8 performer 8.00.7 (Yes, I did the reset button 30 sec + 30 sec unplug)

  The modem is a Westell with routing, but I disabled it the Routing and set it to bridged Ethernet. The PPPoE crosses the WRT54G.

  MTU to auto, it sets to 1492.

  If I run my PC with just the Westell I get timeouts on the port of controls, if I run it bridged and DMZ with the WRT54G I have CLOSED all ports except for 135, 139, and 445.

  All computers on the network are automatic transfer fails.

  1 DMZ transfers all ports that are not transferred in the opposite case. All ports configured on the port forwarding page are always transmitted a.100 and never a.104

  2 transfer. you the ports 27000-27215, 80, 110, 21, 139 a.100

  However, there is nothing running on ports 27000-27215, 80, 21, 110. The only active port is TCP 139.

  If you run the scan of port and you run any other firewall on the computer, you should see the transferred ports as closed. All ports can be closed or covered up (I think that your router does not respond that it is stealth).

  So, if it seems to me as if what you see on the online port scanner is entirely correct: it shows the ports closed because these ports are closed on your computer, you don't have anything running on ports. Transfer do not "open" ports. It only passes the ports. The ports appear in the State, as they appear on the computer. If the port on the computer is closed transfer will not be 'open '.

• Is my 2011 macbook pro the neck of the bottle in my LAN slow transfer speed?

  Hello

  I have a macbook pro 2011 and I recently bought a buffalo LS 520 NAS, but when you try to transfer data through my wifi network that speeds are painfully slowly.

  WiFi area speeds as follows:

  Upload: 0,6906480 MB/s

  DOWNLOAD: 6,2196480 Mbit/s

  And here's the transfer speeds for the macbook pro on the NAS directly connected via ethernet

  Upload: 62,689 Mbps

  Download: 796.3651920

  I have a Sky Home Hub router 2013 (144Mbps and 2.4 GHz)

  I think that the might of bottleneck the NIC in my macbook pro, but I am not sure. Even if that were the case, the speeds above seem very slow. I am planning to buy a new router to see if that improves things, but will it be useless if the speed is dictated by my macbook?

  You need a router more...

  Especially if you want to use wifi for transferring files you need in 5 GHz... so I don't spend much time worrying about this.

  Get a new router... you can plug into the hub of the sky... It should be wireless AC so it may be a new extreme Apple or it can be a dozen different brands... all that is readily available and reasonable price... but I highly recommend types AC1900 like Netgear R7000, Asus RT-AC68U or C9 of TP-Link.

  Once you have plugged it in the WAP configuration / Skyhub mode (bridge on the extreme) we can establish if there are still questions what is happening.

  Your 10 x difference in upload and download speed makes no sense. Which affects both wireless and ethernet. The difference in speed of reading and writing on a NAS is double at most.

  But I do not pretend do you a test, ethernet jack directly to the Buffalo and implemented with the static IP as well as your laptop... and then try it... view results... because if these figures are also very strange, then there is a problem with the buffalo...

  It is very important that you her mount smb in El Capitan... the question is something you need to post in the area of the BONE...

• How to transfer data from a computer to another model using LAN cable

  you try to transfer data using the network cable between 2 laptops. a (old laptop on widows XP) says - limited connectivity and the other (new with windows 8) shows the same.

  How to transfer files and settings from another PC.

  http://Windows.Microsoft.com/en-us/Windows-8/transfer-files-settings-another-PC