Tunnel traffic through the Access Point

Similar Questions

• Impossible to pass traffic through the VPN tunnel

  I have an ASA 5505 9.1 running.   I have the VPN tunnel connection, but I am not able to pass traffic. through the tunnel. Ping through the internet works fine.

  Here is my config

  LN-BLF-ASA5505 > en
  Password: *.
  ASA5505-BLF-LN # sho run
  : Saved
  :
  : Serial number: JMX1216Z0SM
  : Material: ASA5505, 256 MB RAM, 500 MHz Geode Processor
  :
  ASA 5,0000 Version 21
  !
  LN-BLF-ASA5505 hostname
  domain lopeznegrete.com
  activate the password
  volatile xlate deny tcp any4 any4
  volatile xlate deny tcp any4 any6
  volatile xlate deny tcp any6 any4
  volatile xlate deny tcp any6 any6
  volatile xlate deny udp any4 any4 eq field
  volatile xlate deny udp any4 any6 eq field
  volatile xlate deny udp any6 any4 eq field
  volatile xlate deny udp any6 any6 eq field
  passwd
  names of
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  interface Vlan1
  nameif inside
  security-level 100
  IP 192.168.116.254 255.255.255.0
  OSPF cost 10
  !
  interface Vlan2
  nameif outside
  security-level 0
  IP 50.201.218.69 255.255.255.224
  OSPF cost 10
  !
  boot system Disk0: / asa915-21 - k8.bin
  passive FTP mode
  DNS server-group DefaultDNS
  domain lopeznegrete.com
  network obj_any object
  subnet 0.0.0.0 0.0.0.0
  the LNC_Local_TX_Nets object-group network
  Description of internal networks Negrete Lopez (Texas)
  object-network 192.168.1.0 255.255.255.0
  object-network 192.168.2.0 255.255.255.0
  object-network 192.168.3.0 255.255.255.0
  object-network 192.168.4.0 255.255.255.0
  object-network 192.168.5.0 255.255.255.0
  object-network 192.168.51.0 255.255.255.0
  object-network 192.168.55.0 255.255.255.0
  object-network 192.168.52.0 255.255.255.0
  object-network 192.168.20.0 255.255.255.0
  object-network 192.168.56.0 255.255.255.0
  object-network 192.168.59.0 255.255.255.0
  object-network 10.111.14.0 255.255.255.0
  object-network 10.111.19.0 255.255.255.0
  the LNC_Blueleaf_Nets object-group network
  object-network 192.168.116.0 255.255.255.0
  access outside the permitted scope icmp any4 any4 list
  extended outdoor access allowed icmp a whole list
  outside_1_cryptomap list extended access permitted ip object-group LNC_Blueleaf_Nets-group of objects LNC_Local_TX_Nets
  inside_nat0_outbound list extended access permitted ip object-group LNC_Blueleaf_Nets-group of objects LNC_Local_TX_Nets
  LNC_BLF_HOU_VPN list extended access permitted ip object-group LNC_Blueleaf_Nets-group of objects LNC_Local_TX_Nets
  pager lines 24
  Enable logging
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 741.bin
  don't allow no asdm history
  ARP timeout 14400
  no permit-nonconnected arp
  !
  network obj_any object
  NAT dynamic interface (indoor, outdoor)
  outside access-group in external interface
  !
  router ospf 1
  255.255.255.255 network 192.168.116.254 area 0
  Journal-adj-changes
  default-information originate always
  !
  Route outside 0.0.0.0 0.0.0.0 50.201.218.94 1
  Timeout xlate 03:00
  Pat-xlate timeout 0:00:30
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  identity of the user by default-domain LOCAL
  the ssh LOCAL console AAA authentication
  AAA authentication enable LOCAL console
  Enable http server
  http 192.168.2.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
  Crypto ipsec pmtu aging infinite - the security association
  card crypto outside_map 1 match address outside_1_cryptomap
  peer set card crypto outside_map 1 50.201.218.93
  card crypto outside_map 1 set transform-set ESP-3DES-SHA ikev1
  outside_map interface card crypto outside
  Crypto ca trustpoint _SmartCallHome_ServerCA
  no use of validation
  Configure CRL
  trustpool crypto ca policy
  Crypto ca certificate chain _SmartCallHome_ServerCA
  certificate ca 6ecc7aa5a7032009b8cebcf4e952d491
  308204 4 a0030201 d 308205ec 0202106e cc7aa5a7 032009b 8 cebcf4e9 52d 49130
  010105 05003081 09060355 04061302 55533117 ca310b30 0d 864886f7 0d06092a
  30150603 55040 has 13 0e566572 69536967 6e2c2049 6e632e31 1f301d06 0355040b
  13165665 72695369 676e2054 72757374 204e6574 776f726b 313 has 3038 06035504
  0b 133128 63292032 30303620 56657269 5369676e 2c20496e 632e202d 20466f72
  20617574 7a 656420 75736520 6f6e6c79 31453043 06035504 03133c 56 686f7269
  65726953 69676e20 436c 6173 73203320 5075626c 69632050 72696 72792043 61 d
  65727469 66696361 74696f6e 20417574 686f7269 7479202d 20473530 1e170d31
  30303230 38303030 3030305a 170d 3230 30323037 32333539 35395a 30 81b5310b
  30090603 55040613 02555331 17301506 0355040a 130e5665 72695369 676e2c20
  496e632e 311f301d 06035504 0b 131656 65726953 69676e20 54727573 74204e65
  74776f72 6b313b30 5465726d 20757365 20617420 73206f66 39060355 040b 1332
  68747470 7777772e 733a2f2f 76657269 7369676e 2e636f6d 2f727061 20286329
  302d 0603 55040313 26566572 69536967 61737320 33205365 6e20436c 3130312f
  63757265 20536572 76657220 20473330 82012230 0d06092a 864886f7 4341202d
  010101 05000382 010f0030 82010 0d has 02 b187841f 82010100 c20c45f5 bcab2597
  a7ada23e 9cbaf6c1 39b88bca c2ac56c6 e5bb658e 444f4dce 6fed094a d4af4e10
  9c688b2e 957b899b 13cae234 34c1f35b f3497b62 d188786c 83488174 0253f9bc
  7f432657 5833833b 330a17b0 d04e9124 ad867d64 12dc744a 34a11d0a ea961d0b
  15fca34b 3bce6388 d0f82d0c 948610ca b69a3dca eb379c00 48358629 5078e845
  1941 4ff595ec 7b98d4c4 71b350be 28b38fa0 b9539cf5 ca2c23a9 fd1406e8 63cd
  18b49ae8 3c6e81fd e4cd3536 b351d369 ec12ba56 6e6f9b57 c58b14e7 0ec79ced
  4a546ac9 4dc5bf11 b1ae1c67 81cb4455 33997f24 9b3f5345 7f861af3 3cfa6d7f
  81f5b84a d3f58537 1cb5a6d0 09e4187b 384efa0f 01 has 38201 02030100 df308201
  082b 0601 05050701 01042830 26302406 082 b 0601 db303406 05050730 01861868
  7474703a 2f2f6f63 73702e76 65726973 69676e2e 636f6d30 12060355 1 d 130101
  ff040830 02010030 70060355 b 200469 30673065 060, 6086 480186f8 1 d 060101ff
  45010717 03305630 2806082b 06010505 07020116 1 c 687474 70733a2f 2f777777
  2e766572 69736967 6e2e636f 6d2f6370 73302 has 06 082 b 0601 05050702 02301e1a
  1 c 687474 70733a2f 2f777777 2e766572 69736967 6e2e636f 6d2f7270 61303406
  03551d1f 042d302b 3029 has 027 a0258623 68747470 3a2f2f63 726c2e76 65726973
  69676e2e 636f6d2f 2d67352e 70636133 63726c 30 0e060355 1d0f0101 ff040403
  02010630 6d06082b 06010505 07010c 59305730 55160969 5da05b30 04 61305fa1
  6 d 616765 2f676966 3021301f 2b0e0302 30070605 1a04148f e5d31a86 ac8d8e6b
  c3cf806a d448182c 7b192e30 25162368 7474703a 2f2f6c6f 676f2e76 65726973
  69676e2e 636f6d2f 76736c6f 676f2e67 69663028 0603551d 11042130 1fa41d30
  1 b 311930 17060355 04031310 56657269 5369676e 4d504b49 2d322d36 301D 0603
  445 1653 44c1827e 1d20ab25 f40163d8 be79a530 1f060355 c 1604140d 551d0e04
  1 230418 30168014 7fd365a7 c2ddecbb f03009f3 4339fa02 af333133 300 d 0609 d
  2a 864886 05050003 82010100 0c8324ef ddc30cd9 589cfe36 b6eb8a80 f70d0101
  4bd1a3f7 9df3cc53 ef829ea3 a1e697c1 589d756c e01d1b4c fad1c12d 05c0ea6e
  b2227055 d9203340 3307c 265 83fa8f43 379bea0e 9a6c70ee f69c803b d937f47a
  99 c 71928 8705 404167d 1 273aeddc 866d 24f78526 a2bed877 7d494aca 6decd018
  481d22cd 0b0b8bbc f4b17bfd b499a8e9 762ae11a 2d876e74 d388dd1e 22c6df16
  b62b8214 0a945cf2 50ecafce ff62370d ad65d306 4153ed02 14c8b558 28a1ace0
  5becb37f 954afb03 c8ad26db e6667812 4ad99f42 fbe198e6 42839b8f 8f6724e8
  6119b5dd cdb50b26 058ec36e c4c875b8 46cfe218 065ea9ae a8819a47 16de0c28
  6c2527b9 deb78458 c61f381e a4c4cb66
  quit smoking
  crypto isakmp identity address
  Crypto isakmp nat-traversal 1500
  Crypto ikev1 allow outside
  IKEv1 crypto policy 10
  preshared authentication
  aes-256 encryption
  sha hash
  Group 5
  life 86400
  IKEv1 crypto policy 65535
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH stricthostkeycheck
  SSH 0.0.0.0 0.0.0.0 inside
  SSH 0.0.0.0 0.0.0.0 outdoors
  SSH timeout 5
  SSH version 2
  SSH group dh-Group1-sha1 key exchange
  Console timeout 0
  management-access inside

  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  attributes of Group Policy DfltGrpPolicy
  Ikev1 VPN-tunnel-Protocol l2tp ipsec without ssl-client
  username
  username
  tunnel-group 50.201.218.93 type ipsec-l2l
  IPSec-attributes tunnel-group 50.201.218.93
  IKEv1 pre-shared-key *.
  NOCHECK Peer-id-validate
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the netbios
  inspect the rsh
  inspect the rtsp
  inspect the skinny
  inspect esmtp
  inspect sqlnet
  inspect sunrpc
  inspect the tftp
  inspect the sip
  inspect xdmcp
  Review the ip options
  !
  global service-policy global_policy
  context of prompt hostname
  call-home service
  anonymous reporting remote call
  call-home
  contact-email-addr [email protected] / * /
  Profile of CiscoTAC-1
  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
  email address of destination [email protected] / * /
  destination-mode http transport
  Subscribe to alert-group diagnosis
  Subscribe to alert-group environment
  Subscribe to alert-group monthly periodic inventory
  monthly periodicals to subscribe to alert-group configuration
  daily periodic subscribe to alert-group telemetry
  Cryptochecksum:e519f212867755f697101394f40d9ed7
  : end
  LN-BLF-ASA5505 #.

  Assuming that you have an active IPSEC security association (i.e. "show crypto ipsec his" shows the tunnel is up), please perform a packet trace to see why it's a failure:

   packet-tracer input inside tcp 192.168.116.1 1025 192.168.1.1 80 detail

  (simulating a hypothetical customer of blue LNC tries to navigate to a hypothetical LNC TX Local site server)

• Send all traffic through the vpn tunnel

  Does anyone know how to send all traffic through the tunnel vpn on both sides?  I have a server EZVpn on one side and one EZVpn client on the other.  I'm not natting on each side.  I use the value default 'tunnelall' for the attributes of group policy.  On the client side all traffic, even if not intended for the subnet of the side server, seems to pass through the tunnel.  But if I ping the side server, the same rules don't seem to apply.  Traffic destined for rates aside customer through the tunnel, but the traffic that is not pumped on the external interface in the clear.  That's not cool.

  Hello

  Clinet traffic to server through tunnel, that's right, right?

  Traffic from server to client through tunnel, but the rest of the traffic is not, no?

  This works as expected because in ezvpn, politics of "tunnel all ' is for traffic is coming from the client., do not leave the server.

  Side server, customer traffic will pass through tunnel, the rest used.

  Sian

• Could you let me know on 3850 catalyst to connect to the access point status?

  Dear experts,

  The 3850 catalyst to connect the Access Point.
  I checked the OCC, but I don't know to connect the access point directly or indirectly...
  Is that it must connect the Access Point to the 3850 catalyst directly?

  Could you let me know on 3850 catalyst to connect to the access point status?
  I want to know the ORC page on this subject.
   
  Best regards
  Takuro

  Hello

  See below

  http://www.Cisco.com/c/en/us/products/collateral/switches/catalyst-3850-series-switches/qa_c67-722110.html

  Q. does the Cisco Catalyst 3850 in charge of indirectly connected access points?
  A. No. switch Cisco Catalyst 3850 will always take the CAPWAP tunnel locally. Pass-through or indirectly connected access point mode is not supported at this time. Note that a model SFP Cisco Catalyst 3850-12 or 24 channels can be a good choice to act as controller of mobility for a stack of switches Cisco Catalyst 3850 ending CAPWAP tunnels locally.
  HTH
  Rasika
  Pls note all useful responses *.

• Monitoring of the Access Point

  Dear all,

  I have WCS and WLC with 90 LWAP Access Points. I joined the WCS and WLC and I am able to see all the LWAP in the GUI of WCS.

  The requirement is, when ever some LWAPs are down, I want to get an alert somehow to report it. Now, without knowing how to do it, I just saw the total quantity and if some LWAP is off, I find it difficult to find one that is broken.

  Can you please suggest me the appropriate method to get the solution

  RBK

  Hello rbk,.

  for simplicity, you can try to change the name of the access point to their specific locations. draw the map of the ap. Once they are in offline mode you will immediately see that ap is declining and where they are, first of all by the names of ap, then by their current location.

  It's better to do before setting the each AP. but still feasible if the AP is already set. you will have more work, however.

  have your floor plan ready with the exact locations of the AP. Note the mac address you set the AP once the ap registers with the controller, you can match with the floor plan and change the name of the access through its exact location point. example Bldg1-GF-AP01-lobby, Bldg1-GF-AP02-Hall, Bldg1-1F-AP01-reception... etc...

  import map in the WCS and assign the accordngly to the ap.

  You'll know exactly which ap is turned off and where exactly.

  hope this helps!

• How can I get my name from the access point?

  Since I bought a modem Arris 228 G and spent my 2 wireless, printers Canon WIFI unable to connect at Optimum!

  Canon said to contact my router creator (Apple Airport Extreme) for the name of the access point get return wireless, WI - FI printers.

  Help, please.

  W.W.

  (Mac Pro 10.6.8)

  The name of the access point is simply the name of the wireless network that provides AirPort Extreme.

  You can see the name of your wireless network by clicking on the WiFi icon at the top of the screen of your Mac and by checking that the name appears.

  

  There will be a check mark next to your wireless network name.. which is also known as a wireless access point.

  It would be the same name that you had before... unless you have changed some settings on the AirPort Extreme.

• Cannot associate the Access Point

  I just bought a WUSB54GSC wireless adapter and try to connect to my wireless router, a WRT54GS2, but it gives me a message saying "can't associate with the Access Point.  I tried several times and tried to reconfigure the WEP key, just in case I screwed up somehow and get this message.  I tried the network unsecured neighbor (signal low, of course) and he gave me the same, too.

  What I know:

  (1) the problem is not with any part of my network, either from my lines (DSL), (ADSL) modem or a router, because I use a wired network right now with no problems and several other devices in my house with built-in WiFi to connect wireless to the same router with the Setup even very well.

  (2) the problem is not that I messed up the WEP key.  I rechecked it multiplies and even went to the router via an Ethernet cable to check what I entered compared to what he shows me, and they have a perfect match.  In addition, as previously stated, various WiFi compatible devices in my house using the same WEP key to connect properly.

  So, I don't understand why I can't connect what either.

  First go to device manage and check if the adapter is installed correctly or not... ? If it is installed correctly then, right-click on the utility of linksys (green square) on the toolbar and click on 'Use Windows to configure' and click on 'yes '...

  Now, if you have Windows XP... Click Start and goto the control panel and double-click on network connections, right click wireless network connection and click View available wireless networks and select your wireless network and click on connect... Now, it will give you the opportunity to put the network/wep key, make sure that you enter the correct network key and confirm... It will connect...

  If you have Windows Vista... Click Start > Control Panel > Network and Sharing Center > click on connect to a network, select your wireless network and click on connect, it should ask for your key/password network, enter the network and password correct key and click on connect... It needs to connect... Once you're connected, you must restart the computer, it needs to connect to the Internet...

  Also try to change the wireless channel of the router to 11-2, 462 GHz and then try again...

• Mobile data does not and the name of the Access Point settings are not available

  I don't have a mobile data, not even the small up and down arrows or letters beside the sims signal bars appear.

  I tried all the troubleshooting settings and different type of network, the airplane mode is off, mobile data are no limit, no power save modes are on. Phone is dual sim so I tried on the two sims and tried to disable the other sim and changing the sim slots, both sims are loaded with a credit of data that works in other android devices. WiFi works fine. Factory reset does not help.

  There is that one thing that I can't not try troubleshooting. When I select settings > more > mobile networks > access point names, it says

  "Access Point name settings are not available for this user.

  Maybe if I could put APN I could get mobile data. How can I do or how I can try to get mobile data to work?

  Phone's Xperia M4 Aqua E2363 with build 26.1.B.2.102 thanks if you can help

  This text is a bit misleading, which is something that I have forwarded internally as your comments.

  If you have no NPP stored the phone displays the text "the name of the Access Point settings are not available for this user" even if you use the owner account and have access to the settings.

  Try to download the automatic settings from settings-> more-> Internet settings and see if that helps.

• Receiving the message "Wireless association failed because Windows did not receive response from the access point or wireless router" _

  My laptop was working fine yesterday, but when I started it today I get the message "Wireless association failed because Windows did not receive response from the access point or wireless router.

  I can see my network and I can connect to the internet using my desktop pc, but just to make complicated I can't even connect to the network when I plug the ethernet cable into my laptop.

  I think it might be a driver problem, but I have no idea how to solve this problem without access to the internet on my laptop.

  I'm running Vista and my wireless router is an Atheros AR5009 809.11a/g/n

  I need step by step instructions on this Yes please treat me like a fool!

  Thank you

  Laptop would not work at home thus concluded that it was a BT Broadband do not issue my driver (despite BT telling me the opposite last night)

  After the call to a fantastic Lady in BT it's all fixed and thanks to Jack I now know a lot more on connecting wireless to my laptop!

• C4780 wireless printer cannot find the access point

  I have c4780 wireless printer.  It will print fine using the usb connection, but has never printed wireless.

  PC operating system is Windows Vista.  Wireless router is the linksys WRT54G.  The printer does not see the access point.  The security mode of the router is WPA Personal.  I have a unique SSID.  ISP is Timewarner Roadrunner.

  How do I get this to a wireless connection?

  Try this firmware update.

  In addition, sweat you are broadcasting your SSID and not using MAC filtering.

• Updating of the access points in the environment, the models?

  I'm going slow in the environment by replacing the access points 80 AIR-1252.  I decided to replace our 1142 s at the same time so that the environment is up to date.  I was curious what the replacement recommended for these access points.  I see Cisco recommends the 1262 in lieu of the 1252.

  I work for an oil and gas company with locations across the country.  We use two 5508 s with Flex Connect runs the last code 7.3 7.4 into account in the next 6 months.  Our sites are a mixture of office space with warehouse or other environments difficult. I think 2602 s to replace the 1142 s and 1252 s mounted in offices, and I'm leading 1242 s to replace the 1252 s mounted in our warehouse/truck Bay environments.

  Well the 1262 did replace the 1252, but then Cisco came out with the 3502e and the 3602e.  Then maybe you should look at is using the 2602i in the office areas and maybe the 2602e in the area rugged or even look at the 3502e/3602e.  This way, you have all the AP that can sustain CleanAir.

  Thank you

  Scott

  Help others by using the rating system and marking answers questions as 'response '.

• How to set up the access point 1602 I just bought

  Hello world

  Hope you can help. I just bought an AIR-SAP1602I-A-K9 with an internet provider. With her, I also bought a power injector. I tried to use it as a standalone AP. It does not come with any instruction, and I'm not good at Wifi config. I hope you can help... My requirement of adjustment is very simple:

  -Create and broadcast the SSID called MYCSL

  N ' not no authentication or encryption. (is this open authentication?... so that people just plug the SSID as the user can start to cruise internet without putting in any key.)

  -The access point does not have a static ip assigned, instead, he gets an IP from one of my dhcp server in the network.

  -How to connect my laptop to configure via web http?

  Can you tell me what should be configured? Although it is a new product from a legitimate retailer... Cisco said that they could not support it without any contract of Starnet... as a consumer... they should give the kind of grace period to support the new products... In any case, hope you can help me out here :)

  I thank very you much for your help in advance.

  Takami Chiro

  Hi Takami,

  Take a look at one of the previous announcement. I would be more similar. Hope this will help you keep started. If you are the kind of things anywhere you please come back the Forum and someone will be able to help you.

  https://supportforums.Cisco.com/discussion/12217126/access-point-air-SAP...

  Hope that helps.

  Concerning

  Najaf

• High utilization of the processor in Mode VSS when traffic through the internet.

  Hi all

  I have a problem with the installation of VSS. The VSS service install act as a central office switch of transit for internet traffic and the problem arises when there are about 600 Mbps of traffic through the switch. We notice that there are a lot of packages being softswitch and the rate is quite high, almost like 100 to 200 k per second.

  The VSS switch manages ospf and BGP and have plenty of internet routing. After investigation of high CPU usage, I noticed that the AAGR switch is full and has tried to set the course of max mls to the maximum cef and restarted the VSS service.

  Unfortunately, the problem persists after restarting.

  We had planned to filter the full internet routes and enable by default and ospf route only in the VSS service and restart the VSS service to make sure that the table AAGR is not overloaded.

  If I fail the next step is to return to autonomous mode and hope that the processor will not pull up.

  My Question: These step will prevent the issue? Suggestions or the reference similar to the problem I am facing in?

  Hello Sophie,.

  unless you have a PFC 3CXL and all the DFCs the AAGR 3CXL can manage only 256 000 IP prefixes and nowdays that complete a table is in order or 310-320 000 routes.

  See

  http://www.Cisco.com/en/us/prod/collateral/switches/ps5718/ps9336/product_data_sheet0900aecd806ed759_ps708_Products_Data_Sheet.html

  http://www.Cisco.com/en/us/prod/collateral/switches/ps5718/ps708/product_data_sheet09186a0080159856.html

  See table 1 in the second link it tells what I wrote in the first line.

  > We planned to filter the full internet routes and enable by default and ospf route only in the VSS service and restart the VSS service to make sure that the table AAGR is not overloaded.

  You should not need the device after accepting only the default route in OSPF or BGP AAGR use will be greatly reduced this is just wait a few minutes (unless there is an underlying SW bug) for the MSFC to update CFP and then all DFCs

  Hope to help

  Giuseppe

• Error message 'Please select the access point or wireless router to set up' when you set up a network

  Original title: set up a network.

  I want to create a wireless network for the games, and when I click on the network. A screen comes written on this "Choose the access point or wireless router to set up" and that "it might take 90 s for devices reconfigured to appear on your computer.

  But no device never appears below it, even after 90 minutes.
  Please help me with this.
  It was so easy in windows 7.

  Hi Manas,

  What is the brand and model of the Wireless Router/Access Point?

  Given that the issue has not persisted in Windows 7, there is a chance that the wireless router/Access Point is not compatible with Windows 8.

  Please check the links below on the implementation of a network.

  http://Windows.Microsoft.com/en-in/Windows-8/Setup-home-network

  http://Windows.Microsoft.com/en-in/Windows-8/what-you-need-Setup-home-network

  http://Windows.Microsoft.com/en-in/Windows/set-up-wireless-router#set-up-wireless-router=Windows-8

  http://Windows.Microsoft.com/en-in/Windows-8/Add-device-or-PC-to-network

  Answer please if you have any questions.

• Launch of Lightroom 6 is not. error: "can't find the access point of the procedure _crtCreateSymbolicLinkW in the MSVCR110.dll dynamic link library.

  It says: "cannot find the access point of the procedure _crtCreateSymbolicLinkW in the MSVCR110.dll dynamic link library. What can I do? I have already uninstall and then reinstall the software...

  It is indeed a microsoft problem, check here:error "did not find the entry point _crtCreateSymbolicLinkW - Microsoft Community .