Two networks

Similar Questions

• correct settings for two networks?

  I have a desk that has a building at each end of the city.  I have a wireless bridge that connects the buildings.  Each building is on its own ip configuration and has its own internet connection.  I have a server for A construction program.  I want to be in the B building clients connect to this server, but still use internet and print to printers on their own network.

  Right now the wireless bridge has the same addresses as a. construction I also fooled with assignment of two for each clients network adapter ip addresses.  This works fine, except that I see only computers B building in the Working Group, and I don't know if its using internet of B building or A building.

  Building A uses 192.168.5.x - 255.255.255.0 - 192.168.5.1

  Building B uses 192.168.10.x - 255.255.255.0 - 192.168.10.1

  Any help is appreciated, and I can give you more information if necessary.

  Hello

  I don't know what hardware you are using specifically. Regular Bridging could not do you need a device for routing between two independent

  Networks that are on a different subnet.

  If the two networks are bridge successfully to act as a coherent networks (same subnet), choose which Internet connection would be used by each computer can be made by assigning static IP addresses and gateway entrance to TCP/IP on the computer the IP number of the router as the Internet should be used,

  Passing by the details beyond the scope of the forum of support to end users. If the above do not help, you should get a consultant on-site.

  Jack - Microsoft MVP, Windows networking. WWW.EZLAN.NET

• HP Wireless of D110 find two networks

  My HP D110 found two networks with the same name... apparently one of my router Verizon Actiontech (several 192.X on channel 11) and one of my Apple Airport Express (10.0 several on Channel 6). The Network Setup page confirms this. After that the power is out at home, the D110 only reconnects to the network 10.0 (even after several attempts to unplug and try again). Unfortunately, all my computers (MAC) are on the 192.X network, and the printer cannot find them.

  Is there a way I can "force" the D110 to connect to network 192.X, rather than the 10.0 network?

  Any help would be much appreciated I'm unable to print at all.

  Thank you.

  Steve

  Spencer,

  I got it to work! I have re-directed the whole upward after having disconnected the USB cable. When I went to my Macbook, under , I chose the D110. A box came asking me to install the printing software (do not know why, since I had already downloaded and installed on the link you gave me. A message came up saying that the software was not available from Apple and I need to contact HP. I tried again, this time instead of choosing the D110 in the list, I chose 'add printer' and selected option D110 "Hello". Always without success, until... I changed the setting in the drop "D110 having printed" for "print using Airprint. That seemed to do the trick, and now it's new to print wireless.

  Thank you very much for your help!

  Steve

   

• Communication between two network cards on windows 2003

  Hi all

  I need your help.

  I have a machine virtual windows 2003 with two network adapters.

  NIC 1 - external - 192.168.1.101

  Map NETWORK 2 10.10.10.1 - internal -.

  I've configured to operate as a DC and DNS serving 10.10.10.x network.

  DNS is configured to resolve before on 192.168.1.1 as redirector DNS requests.

  I have other machines connected to the 10.10.10.x network.

  They can ping 10.10.10.1, they can ping 192.168.1.101 but not 192.168.1.1

  I want to just be able to talk to 192.168.1.1 and be able to access the internet.

  No firewall between the two.

  Command-line may help, but I would need your help.

  Hello Prasad,

  The problem you are having is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public.

  Please post your question in the TechNet Forum.

  https://social.technet.Microsoft.com/forums/en-us/home?category=WindowsServer&filter=AllTypes&sort=lastpostdesc

  Hope this helps you solve the problem, if any question you can write us and we will be happy to help you further.

• Connect two networks with different subnets

  I have a network that is totally excluded from the rest of the network. It consists of a switch Allied Telesis AT - 8624T layer / 2M 3, a computer and a few PLC devices.

  It is the only switch Allied Telesis, the rest of our network is Cisco. Allied was by a seller.

  Our network uses a 10.10.1.X network, but this standalone network uses a 192.168.201.x. I need to connect the two networks, because a system on the network 10.10.1.x need to access the computer on the network 192.168.201.x. I wonder if I can do it with a 2960 s Cisco or if I should get a router between the two switches.

  I am pretty new to the implementation of this type of equipment, was suddenly thrown into the mix, I appreciate any help that can be offered. Thank you.

  Hello!

  You can do this with your switch 2960, they take over the static routing. Please see the following link for detailed configuration instructions:

  http://www.Cisco.com/c/en/us/TD/docs/switches/LAN/catalyst2960/software/...

  You will not be able to perform routing inter - vlan but pointing your static routes to the other managed switch interface you will be able to achieve. BE aware that the other switch must have some sort of routing capabilities too or you will need to get a router.

  I hope this can help, greetings!

  JC

• Is - a used the 3602e as a bridgeing only between two networks?

  Is - a used the 3602e as a bridgeing only between two networks? 2504 controller version 7.4.100 I can't ping anything on one side or the other of the network, but I can ping from each access point controller. I have two 1552 setup the same way with no problems. Anyone seen this before?

  Thank you!

  In the case of 3602e as bridge link and you bet the config is a working one, then I would check the antennas if they are properly aligned, if you use a higher gain, a good one would be a necessary in the case of 3602e, I think that Yes.

• Since the execution of an update of windows, I still lose my two network icons in windows Explorer.

  Original title: lost icons

  I'm on Windows 7 Ultimate 64-bit on a home network with two computers, and two network storage devices since I did a big update windows I keep losing my two network icons in windows Explorer, but I can see other computers

  Hi PeterHH,

  You're talking about the two icons of network in windows Explorer? Is storage devices?

  Method 1:

  You can try to run the network troubleshooter, and check if it helps:

  Windows wireless and wired network connection problems

  Method 2:

  You can also refer to the computer or the device manufacturer's Web site and try to install the latest version of the network card drivers:

  Update drivers: recommended links

• Network configuration / routing / two network interface cards / NAT - leased / dedicated Dell R210 running VMware ESXi 5.1.0 build-799733

  Network configuration / routing / two network interface cards / NAT - leased / dedicated Dell R210 running VMware ESXi 5.1.0 build-799733

  Hello

  I'm trying to understand how to configure a dedicated server of Dell R210 rented running VMware ESXi 5.1.0 build-799733

  This dedicated server is rented www.online.net and sits somewhere in France. One of its network adapters have an IP public 62.210.177.20x. The other NIC is here, but I do not understand how it is configured. According to the www.online.net portal, the other NETWORK card has or should have an IP 10.90.116.20x. And I am obviously set up is to have some virtual machines running and be able to access the Internet. I have access to the console of the server Dell through iDRAC and since I could see, one of the network adapters in the IP is 62.210.177.20x defined, and the other has been shown out of service. I managed to make it appear the other interface but I cannot find anywhere how to assign the IP address 10.90.116.20x to this 2^nd network adapter. But then again I don't even know if I should or if I need to assing a IP address to this 2^nd network adapter. What is the cable connected even for this 2^nd NIC? I do not know. Should it be - I'm not either. I don't know French and manuals/instructions on www.online.net are in French. I can try an online translator, but I don't think that what I'm looking for is explained. How do I get this set up? I have to do something about the ESXi on the server console? This interface 2^nd should be in place, or it must be down as if it was originally? Yesterday after watching someone videos on YouTube, I added the second virtual switch and moved the virtual hosts of this switch 2 and he entrusted the 2^nd NIC. But that 2^nd NIC had a red X next to it probably indicating that it was disconnected the 2^nd form virtual switch. Today and now I have managed to access the ESXi console server through iDRAC, I bring the 2^nd NIC, and now both network adapters are assigned to the virtual switch 1^st . But I think that a NIC should be attributed to a single switch and the other card NETWORK on the 2^nd switch. I'm just a desktop guy with enough knowledge to be dangerous J if you / someone put in steps how and where to set them up it... PLEASE

  Thanks in advance

  cweks

  ~ # vmware - v

  VMware ESXi 5.1.0 build-799733

  ~ # esxcfg - road

  VMkernel default gateway is 62.210.177.1

  ~ # esxcfg-vmknic-list

  Interface Port Group/DVPort IP IP family address Netmask Broadcast MAC address MTU TSO MSS active Type

  vmk0 management network IPv4 62.210.177.20x 255.255.255.0 62.210.177.255 d4:ae:52:cb:bb:84 1500 65535 true STATIC

  vmk0 networking fe80::d6ae:52ff:xxxx:bb84 64 d4:ae:52:cb:bb:84 1500 65535 true IPv6 STATIC, PREFERRED

  Portal www.online.NET--information

  NORMAL 1 ready 62.210.177.20x xxx.domain.eu.       D4:AE:52:AB:BB:84

  2 PRIVATE loan 10.90.116.20x d4:ae:52:ab:bb:85

  http://wiki.hetzner.de/index.php/VMware_ESXi/en#Network_configuration

  Network configuration

  • VMware vSphere Hypervisor is an "operating system" for pure virtualization and support NAT or routing. Therefore, only a real bridge configuration can be used.
  • To use a subnet additional IP must be configured as a router VM.

  If I understand the above, I need to show some VM and set up as a router? If the virtual machine that will act as a router must have two network interfaces, where it is connected to a switch and the other to the other switch network card. Am I do? The YouTube video that suggested, but I thought that maybe / somehow ESXi can route packets between the two network cards, but from what I read, ESXi can route packets. Do I need to order an additional / extra / 2nd IPv4 address so that it can be assigned to the interface of the router?

• two networks showing on vm when one network card installed.

  Hello

  I have a virtual computer whose use have two network adapters, a network card was on vm
  a vlan 20 of the network and the other was on vm two network vlan 21, one of the
  interface cards network has been disabled. I have now deleted one of the network adapter, but when I look at the
  standard switch it is always showing the virtual machine to be on both networks. If I look at
  the summary of the virtual machine, it also appears
  It is in the two networks. It is in sight for VI client connected to
  vCenter. If I connect the host to the virtual machine runs then all
  properly, shows a network card in a network.

  Any ideas how to fix this seen vcenter?

  If the virtual machine has Active snapshots, the deleted virtual network adapter will display until you delete the snapshot. The reason is that ESXi must remember the configuration of the 'old', where you decide to go back to a snapshot that was still the second NETWORK card in use.

  André

• Two NETWORK adapters on the host

  I have a windows xp host and he has two NICs. One is used to connect to the internet, and the other is used to connect to a private network of Novell.

  What is the best way to configure my VM Windowx98SE so that it can use both of these connections?

  If I have a single configuration network adapter on my VM and use NAT, I can connect to the internet, but not of Novell.

  If I have a single configuration network adapter on my VM and use Bridged, I can connect to my Novell network, but not internet.

  If I place two network cards on the VM and the whole NAT and the other to connected by a bridge, I can connect to Novell, but not internet.

  Any ideas?

  Thank you

  Josh

  Well, it turns out that the adapter "set" parameter is Global not by NIC so you must briing the real Publisher virtual network and create a second bridged VMnet, say VMnet2 and then jumpered VMnet0 and VMnet 2 to different network card.  Then caraa change the second NETWORK card in the .vmc configuration file to account for the bridged custom VMnet2.

  ethernet1.connectionType = "custom"
  ethernet1.vnet =  "vmnet2"
  

  To display the real virtual network editor in VMware Player 5 in an administrator command prompt, change the directory for VMware Player and use the following command.

  rundll32.exe vmnetui.dll VMNetUI_ShowStandalone
  

• Binds a guest operating system to one of the two network adapters on the host computer?

  Sorry if the topic is confusing.  I have a host operating system to Server 2008 running on a server that has two network jacks.  Allows to call an (192.168.10.24) and B (192.168.10.25).

  My guest operating system is set to bridged with the IP 192.168.10.26 mode

  I want to say VMWare to always use A NIC when it comes with this guest operating system.  Is this possible?

  In my (Control Panel Windows) network connections, I see my two NICs A and B as well as VMWare Network Adapter WMnet1 and VMnet8.

  Thank you!

  Run the utility for configuring the network (vmnetcfg.exe) as an administrator on the host computer, disable the automatic bypass, set vmnet0 to one of your physical network cards and a virtual NETWORK adapter not used, such as VMnet2, and then assign the other physical NIC. Then to your comments, change its settings and select vmnet0 or vmnet2.

  Guy Leech

  VMware vExpert 2009

  ---

  If you have found this device or any other answer useful please consider the use of buttons useful or Correct to award points.

• Two network adapters physical separate networks

  Is it possible to implement two physical on a host running VMware Workstation Desktop cards, in a way where your host operating system uses one of them and one invited the other?  I need the host and guest on separate physical networks?  Example - my host OS is on our production network, but I want my guests to be on our test network.  Two physical production and test networks are completely separate and no physical connection between them.  Basically, my host Office would be multi-homed.

  Thank you

  Guest VM traffic is done only to the vnet to which you connect.  Therefore, if you configure NIC1 to be on by default in bridge network (vnet0) and NIC2 be bridged to vnet2 (for example), and then configure your guests with a vNIC connected to vnet2.  The prompt only "sees" everything that is connected to NIC2, because it is NOT connected to vnet0/NIC1.

  If you do not need host to go on the network at alltest traffic, you can disable the TCP protocol on the network to test NIC so no traffic host never goes that NIC just let VMWare bypass protocol enabled in order for the traffic of the virtual machine on this NIC

  However, if your host must have access to both networks, then imagine that virtual machines are running on another host on the network.  With your current physical machine with two network cards, ask you the same question: How can you guarantee that the traffic of the computer is done on the production network?  If you do not set a gateway for TCP/IP host on the NIC test network, so that traffic destined for this subnet test will go to this network adapter.  This means that two networks have different subnets, of course.  If the two networks are the same digital subnet (for example: both are 192.168.1.x) then you will have problems even in the absence of the virtual machines.

  The reason you do not set (and normally are not allowed to have two gateways) is if the traffic is destined for a subnet that your computer is not directly connected to, then your machine comes into contact with the bridge.  If you have two (or more) gateways, which is your machine contact?  Beyond simple dishes networks as in this example, you will probably need the assistance of an expert network.

• OfficeJet pro 8600: my two network printers has stopped printing

  I have two printers officejet pro 8600 in my house. All of a sudden both are not available from any laptop or mac on the network. This issue is not isolated to a single laptop or a printer. Printers are online and have an IP address. However, if I type the IP address in a browser, it can not be found. If I use the function "" update IP address"and run a search, it fails. I am certainly on the same network.  I always can email docs to my address hpeprint. Please advise...

  Turn off the printer and router. Turn on the router and wait 3 minutes. Now the power on the printer and wait they connect to your router, check. Try now.

• my computer has two network icons, 1394 and con LAN. Either, especially the icon of LAN began to move to items being passed in the system tray when I start the computer.

  I have a new and strange behavior on my computer. Until recently, the two icons, 1394 connection and LAN icons always used to appear in the whole system tray after the computer has been started. Is no longer the case. Whenever I start the computer, I don't see the icon of LAN but discover that it attributed to items passed. Then I open the properties of the network connection, uncheck 'Show the icon in the system tray', click Apply + OK, then I open the properties, check the box again, click Apply + OK; only the LAN icon is displayed in the system tray. I'd appreciate any help with this problem. The situation is sometimes the reverse case, i.e., LAN icon appears in the system tray, but I find the icon to connect 1394 points ago. I put the properties in the Start Menu, the toolbar always showed.

  Hi ErhanKarabekir,

  1. Did you the latest changes on the computer?
  2. You have security software installed on the computer?

  Method 1

  Refer to the article below and try the steps mentioned, check if it helps.

  How to troubleshoot missing network connections icons in Windows Server 2003 and Windows XP

  http://support.Microsoft.com/kb/825826

  Method 2

  If the previous step fails to them it is possible that some third-party programs installed on the computer is causing the problem.

  I suggest that you put the computer in a clean boot state and check if it helps.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See the link below to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  (a) click Start, type msconfig in the search box and press ENTER.

  (b) If you are prompted for an administrator password or for confirmation, type your password or click on continue.

  (c) under the general tab, click the Normal startup option, and then click OK.

  (d) when you are prompted to restart the computer, click on restart.

• How to connect two network switches Force10 S4810P

  Hello world

  We just bought two S4810P Force10 network switches and we want to install on two adjacent brackets. They will be used to interconnect computing and NAS storage, installed in two baskets serving mainly local connections.

  We intend to use ports QSFP + to connect the two switches, and I have two questions.

  1. hardware configuration: what are the best transceivers and cables to use in this case?

  2. configuration of the software: should we use stacking or virtual link trunking? the information I've read so far does not give me a definitive answer.

  Thank you very much in advance for your help!

  The server room is already has some inside wiring? If so it be a transceiver that will percolate pre-existing cables. There are also some direct attach cables ranging from 0.5 m to 50 m. Here is an example of a cable direct attach: http://dell.to/23huDl7

  the best course of action would be to contact your sales representative and let them know what your needs are. They can get you city for right connection hardware.

  the VLT and stack the two have the same goal of redundancy, but go about it in different methods with different warnings warning for both. In both scenarios, the redundancy is dependent on each device connection linking the two switches. If you do not do this, then it may be better to let the independent switches. Here is a good blog that compares the VLT and stacking.

  http://bit.LY/1J8nI1Y

  I hope this helps.