UCS/Nexus and FCoE Question

Similar Questions

• Setting port channel between UCS - FI and MDS 9124 (Mode F)

  Dear team,

  We tried to create the channel of port between UCS FI and MDS 9124

  But the port channel do not take action in mode F on MDS 9124

  FI is in host FC end Mode

  We have allowed FC uplink on FI trunking

  We have activated NPIV on MDS

  We have activated the MDS trunk

  FI and MDS in default VSAN

  To check that we have changed the way FI FC channels mode and switch port became active, but in E mode

  When we enabled CF trunking of uplink on the port mode FI channels and FC Switching became active in mode TE

  but in both cases above, showflogi database shows WWPN of SAN alone does not have the any fi.

  How to achieve this?

  Have read that no need to change the mode switching mode of CF swicthing and keep FC Endhost way

  SO how to channel ports with mode F MDS and FI (Display Mode as NProxy)

  What is it has nothing to do with the MDS NX - OS version? (https://supportforums.cisco.com/thread/2179129)

  If yes how to put as license for ports came with the camera and we don't have any CAP/PAK or license file as she came

  with license

  Also, we saw 2 files available for download (m9100-s2ek9-kickstart - mz.5.2.8 .bin and m9100-s2ek9 - mz.5.2.8 .bin b b) to use

  Thanks and greetings

  Jose

  Hi Jo Bo.

  What version of the software if your MDS race?

  On your UCS do connect nxos and show ficelleStringString ficelleT inteface and find the mac address.

  It is possible that you could be hitting the bug below. If this is the case, you may need to update the firmware on your MDS.

  Add MAC YES '002a6a', '8c604f', '00defb' for 5 k/UCS-FI

  http://Tools.Cisco.com/support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId= CSCty04686

  Symptom:

  Link change cannot connect any other Nexus or other Cisco Switch in mode VAN with a port channel F.   Question can be viewed in older versions of 5.1

  5.1.3.N1.1a

  but not later

  5.1.3.N2.1c

  Release. Question is also found in

  5.2 (1) N1 (1)

  and

  6.0 (2) N1 (1)

  and later versions.

  Conditions:

  Nexus configured for the link SAN PortChannels or NPIV Nexus mode connected to the UCS via regular F port channel where UCS VAN VAN edge mode switch: YES switch manufactured FI or another Cisco UCS Port WWN: xx:xx:00:2 has: 6a: xx:xx:xx or xx:xx:8 c: 60:4f:xx:xx:xx

  Workaround solution:

  Turn-off on Nexus 5 k TF-port question link mode does not happen with standard F-PORT SAN to remove Portchannel config

  Other Description of the problem:

  To check question collect please see the flogi-event history internal errors whenever the port is attempted OLS, AMENDMENTS, PBA counters will increment. This can be determined via the following output, view port internal info to see all the internal-historic port of error events

• UCS FI and iSCSI storage

  We are poised to implement a UCS B Series. I have a question for FI 6248UP. I have read and used the emulator for UCS Manager and noticed that you can configure ports FI as ways for storage material. Is it limited to a certain protocol storage or the seller? We use Dell EQ and plan to be there to connect the EQ 6510 X. I was wondering if that is supported and if iSCSI upstream traffic would be able to access the storage?

  The 6248UPs will be passed to a pair of Catalyst 4506-E race vs. We have an IBM chassis and servers should be able to access the EQ6510X too. I guess I just need master iSCSI VLANS for the 6248UP and the servers would have access?

  Thank you!

  Hi Cowetac,

  Yes, not all storage arrays are supported by UCS, but your DELL Equalogic is supported. If you have any questions about the other compatibility of storage arrays, you can take a look at the UCS (see link below) storage interoperability matrix.

  UCS storage interoperability Matrix (matrix of the storage of UCS - B of table 10-2)

  http://www.Cisco.com/en/us/docs/switches/Datacenter/MDS9000/interoperability/matrix/Matrix8.html

  I guess I just need master iSCSI VLANS for the 6248UP and the servers would have access?

  Depends, if you use one port of the device the UCS for you connect directly to storage, you can use a single vlan.

  If you are connected via the Ethernet uplinks via a switch, you need to set your switches as a trunk port.

• I recently dropped my laptop and it is weird, one day he int open up to 4 start times and sometimes it shows me a folder and a question mark in the interface and sometimes asked to reset my password, what are the steps to take?

  I recently dropped my laptop and it is weird, one day he int open up to 4 start times and sometimes it shows me a folder and a question mark in the interface and sometimes asked to reset my password, what are the steps to take?

  Anything can be corrupted on your MacBook Pro, but from what you say, it seems that the cable drive/SSD/flash memory/SATA hard was seriously damaged. Him "question mark" means that your Mac is unable to find any bootable device, meaning that it does not yet detect your OS X drive.

  You should make a backup of your files (if you can still do it) and take the Mac at the Apple Store or dealer to get a diagnosis. There may be several damaged parts.

• How to recover the forgotten password if you have forgotten your password for the alternative account and the question secret

  Hi, I am unable to access my account of * address email is removed from the privacy *. I really need to return as soon as possible because I have a lot of important issues and contacts inside...

  Thank you!

  View all Windows Live and Hotmail questions in the appropriate forum found here:
  http://windowslivehelp.com/

• Kindly unblock my account that I don't remember my email and Security Question.

  Kindly unblock my account that I don't remember my email and Security Question.

  I received important emails in the account. He has been blocked it for a month now.

  Kindly unblock as soon as POSSIBLE.

  I'll be very grateful.

  Thank you.

  Hello

  If you are referring to a Hotmail account, read this

  I'm sorry, but we cannot help with hotmail problems in Microsoft answers Feedback Forum you send to

  Please repost your question in hotmail in the hotmail link below forums

  http://windowslivehelp.com/product.aspx?ProductID=1

  Forums

  E-mail client and the appliance issues

  Hotmail Sign In questions

  Lost or deleted emails

  People and Contacts

  Reading, writing, and formatting mail

  Sending and receiving mail

  Sign in, and sign to the top and account security

  Using the Hotmail calendar

  Using Web Messenger

   

   

  Consult with Microsoft Certified Solutions

  How to work the views Active Hotmail?

  Your account has been temporarily blocked

  What to do if you can't connect to Windows Live Hotmail

  Compromised account - unauthorized account access

  Reset your Windows Live ID password

  Error when you try to send an e-mail: your message seems to have triggered our spam filters.

  Change your Windows Live ID password

• I forgot my password and secret question

  I firgot my password and my question secret, help me please

  Hi TUNCAYTUNCAY,

  ·          You are Ref Err by Windows password or password any program?

  See the link below to learn more about Microsoft support for forgotten passwords.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_xp-security/keeping-passwords-secure-Microsoft-policy-on/024dd682-b3a4-4EA8-8E71-8e4892092a5e

• WinXPsysytem: The upgrade and have questions

  Have a dell e521 that I train and some questions.  Have already updated to 3 GB of memory on x 86 operating system.  Bios version active what 1.1.6 4/7/2007.  Have checked Dells site and they offer a version of bios 1.1.11 released on 04/09/2007.  Having checked their previous versions and mine is not yet in there.  Don't know if I should go with the 1.1.11 version or stick with what is on mine, any suggestions?  Also, I put in a 500 GB seagate HDD.  Have a 80 GB drive there now which is pretty maxed out.  Playing with the idea to put xp pro on the 80 GB and using the programs and storage 500 GB.  I would like to know if it's a good idea or not!  Could use pointers and how much others who have more experience I have of course on my best options for installation.  for performance and features.  Thank you in advance, Ron.

  It's sad to say, you should probably have spent your money on a new computer rather than on the RAM and a new hard drive.  Windows XP (you posted in a forum of Windows XP, that's what I assume you have) will be supported is no longer starting in April 2014. This means no more security updates and therefore increases the vulnerability to malware.

  That said, your system now-updated can probably support Windows 7. You must run the Windows 7 Upgrade Advisor to check the remaining material.

  As you say, Dell does not list the intervening versions of BIOS with 1.1.4, 1.1.10, so unless someone at Dell or in the Dell forums can tell you what "improvements" in your version or with your version 1.1.10, you have no way of determining that. Based on omissions, I think there were only minor changes in these versions.

  Normally, I would leave the BIOS alone.  Note, however, that Dell "recommends" 1.1.10 be installed because
  The update contains improvements or changes that will keep your system current and compatible with other system modules (firmware, BIOS, drivers and software) software.
  If you want to stick with XP, I would leave the BIOS alone. If you want to install Windows 7 (assuming that there are Windows 7 drivers for all your hardware), I would Setup 1.1.11.  Be sure to read and follow instructions carefully.

  BTW, it's a little surprising that you only have a 80 GB drive.  CNET review of the Dimension E521 said he came with a 320 GB drive.

• How can I change my HTTPS thing, so it isn't always pop up and ask questions about the sites Web secure when I play some games?

  Feel free to change the title

  How can I change my HTTPS thing, so it isn't always pop up and ask questions about the sites Web secure when I play some games?

  You're talking about Facebook?

  Try the gyration of the Secure Browsing

  http://www.Facebook.com/help?page=1079

• How do you get access to your computer when you forgot your password and hint question

  My mother did not use his computer for a while and forgot his password and hint question. Is there anyway to get into the computer without them? She has a Toshiba laptop with Windows Vista installed on it.  Thank you.

  Hello

  I'm sorry, but the strategy of microsoft in these forums is that without assistance will be given about lost or forgotten passwords

  read the policy at the link below

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-security/keeping-passwords-secure-Microsoft-policy-on/a5839e41-b80e-48c9-9d46-414bc8a8d9d4

  I suggest you reinstall vista

• UCS 540 and SPA 112 ATA

  Hello community support!

  I have a UCS 540 and want to connect analog phones via SPA112 ATA. Unfortunately this combination is not officially supported, but several positions indicated that it is possible.

  If someone has an idea or a solution that would be greatly appreciated!

  The SPA gets it's IP address via DHCP from the UCS and points to the NVI UCS interface IP as proxy. the IP Address of the ATA is to ping requests.

  Thank you

  Mike

  You're right, they are not supported.  You can configure most likely that SIP phones in the WEC, but I have never seen an example of configuration of it.  You can start here is how to set up a phone SPA in a WCF router using the SIP.

  http://www.Cisco.com/c/dam/en/us/products/collateral/unified-communications/Unified-Communications-Manager-Express/spa_polycom_application.PDF

  Let me repeat that you won't get any support from SB - TAC for this.

• UCS C200 and NIC Teaming/FailOver

  As UCS C200 with management of a 10/100 and 10/100/two interface 1000 interfaces and PCIe with 4NIC

  I want to install CUCM 8.5 is the NIC Teaming/failover supported by UCS C200 and how to set up the NIC Managment interface with failover?

  Thank you.

  Hello

  As you install apps from the CPU on the server of the UCS, speech application team listed their recommendations here.

  http://docwiki.Cisco.com/wiki/QoS_Design_Considerations_for_Virtual_UC_with_UCS#Guidelines_for_Physical_LAN_Links.2C_Trunking_and_Traffic_Sizing

  You can create a NIC teaming in the ESXi via vSphere client software for traffic from from / destined for virtual machines.

  For C200, we have only one management port and if you use the management for MMIC traffic port, switch option is not available.

  However, if you choose to use host for MMIC traffic NETWORK ports, you can set up CIMC NIC mode for 'LOM shared' which provides the NIC teaming options.

  http://www.Cisco.com/en/us/docs/unified_computing/UCS/c/SW/GUI/config/Guide/1.4.1/b_Cisco_UCS_C-Series_GUI_Configuration_Guide_141_chapter_01000.html#concept_AC4EC4E9FA3F4536A26BAD49734F23D0

  HTH

  Padma

• GLC - T allows to connect problem failed validation ucs 6120 and 2960 s (RJ45), are SFP

  Hi, all.

  I use GLC - T to connect ucs 6120 and cisco2960s (RJ45), are sfp validation doesn't have a problem.

  

  I did the speed at 1 G, and then I get error "connection not connected" even, I plugged the cable of nnetwork...

  

  Hello

  I recommend to see if the dealer you bought the glc - t from Exchange.  There seems to be problems with the SFP modules.

• Cisco ACS 5.2 with NX - OS (Nexus) devices user - questions

  Hey, I have a really strange problem with Cisco ACS 5.2 and Nexus NX - OS devices.

  I create an account on ACS, let's call him User1 and give privilege 15. With User1, I am able to access on all our IOS, IOS - XE, ASA and PIX devices with privilege 15.

  When I use the User1 account in our NEXUS devices, I do NOT receive the access privilege 15. As you probably know, the NEXUS devices have roles: predefined or custom roles. So I assumed I would get the role of "network-admin" (15 private read/write) User1 when you connect, but instead I got the role of 'vdc-operator' (private 1 read-only).

  Then I tried to twist User1 and give network-admin under profile Shell > Custom Attributes. I logged in the NEXUS and of course I was able to get a network-admin access. However, my access to ALL other devices (IOS, ASA, PIX, etc.) does NOT work! I am not even able to connect with my login and my password for these devices.

  Has anyone ever experience this problem? Help, please!

  Thank you

  neocec

  This is a common problem when you mix with RBAC and IOS devices authorization policies, the pair av that you created must be set 'optional' instead of 'compulsory', please make this change and you will be able to access all your devices.

  Thank you

  Tarik

• Drag and drop question - Desktop and USB

  Hello!!

  I have an Asus laptop that I bought in September with Windows 8 is installed. I saw drag and drop questions on desktop lately, and I'll provide you with a full run down of what past:

  1. this particular case, I wanted to save my mobile by copying and pasting all the files from my phone to a USB (USB Kingston).

  2. I selected all files, right click to copy, open the folder that I made in the USB for my phone content and do a right-click Paste.

  3. nothing's happened, Explorer seems to have frozen, so I opened the Task Manager and press end task, all closed and restarted my laptop.

  4. I have excluded that my phone was the issue. I was able to create a folder on my desktop and copy and paste all of the content of my phone in the folder on my desktop.

  5. I tried to copy and paste / drag and drop an image from my office to the flash drive. Explorer Windows freezes on the rise again.

  6. I tried another flash drive. Explorer Windows froze again.

  Apparently I'm unable to copy files ON a USB key, which makes the backup and backup of things a headache because Windows Explorer stops working every time.

  I am the only user of this laptop, and I don't know what is happening or what to do. Any help would be appreciated. Windows 8.1 upgrade would solve this problem?

  Hi Karthik,

  1. There is no error message.

  2. I tried earlier drag - move my documents to my flash drive and it works perfectly.

  I just tried again to drag and drop from my office to my flash drive and for some reason, it works again.

  I don't think that was with my flash drives, but with Windows Explorer itself. Nevertheless, it seems to have fixed itself somehow. Thank you very much for your help!