Unable to connect to remote between my home and work PCs

Similar Questions

• Unable to connect to wireless internet at home and cannot renew IP address

  Here's the question:

  I have a few years old Toshiba Satelite laptop with Windows XP SP3. I recently took my office where he has been on the internet via an ethernet cable in the living room where I tried to connect to my wireless internet. It would connect, but says he has "limited connectivity or not." Perfectly fine, I can connect to my neighbor's wireless internet, my wife has the same computer exactly like me and connect to our wireless internet and the neighbour, and there is absolutely no problem with the intensity of the signal. I ran ipconfig and that's what he said:

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. : gateway.2wire.net

  IP address.  . .  . . .  .  . . .  . .  : 192.168.1.64

  Subnet mask. .  . .  . . .  .  ...: 225.225.225.0.

  Default gateway.  .  .  . .  .  ...: 192.168.1.254

  Ethernet wireless network connection card:

  The connection-specific DNS suffix. :

  IP address.  . .  . . .  .  . . .  . .  : 192.254.204.90

  Subnet mask. .  . .  . . .  .  ...: 225.225.0.0.

  Default gateway.  .  .  . .  .  . . . :

  When I just go to the login information and press 'Fix', it tells me that "Windows could not finish repairing the problem because the following action could not be completed: renewing your IP address."

  In addition, I don't know if it's important, but I have DSL service from AT & T with an AT & T 2Wire Gateway. If anyone has any ideas or ideas that could help me, please let me know. Thank you

  Well, I don't know what was wrong, but I got it working now. I just uninstalled and reinstalled all software or drivers or something that had nothing to do with wireless internet and it is now everything works fine.

• Unable to connect to remote PowerShell and get error message.

  I have two computer to Windows 7.

  Unable to connect to remote PowerShell and this error message

  nvoke-command - computername XXXXXX - scriptblock {}
  get-process} - administrator credentials
  [XXXXXXX] failed to connect to the remote server XXXXXX with the
  error message: WinRM client cannot process the request. If the
  authentication scheme is different from Kerberos, or if the client computer is
  not joined to a domain, then HTTPS transport must be used or the destination
  machine must be added to the TrustedHosts configuration. Use winrm.cmd
  to configure TrustedHosts. Note that computers in the TrustedHosts list might
  do not be authenticated. You can get more information about it by running the
  following command: winrm help config. For more information, see the
  about_Remote_Troubleshooting help topic.
  + CategoryInfo: OpenError: [XXXXXX], PSRemotingT
  ransportException
  + FullyQualifiedErrorId: ServerNotTrusted, PSSessionStateBroken
  PS C:\windows\system32 >

  PS C:\Users\Administrator > Invoke-Command - ComputerName XXXX - ScriptBlock {get-process} - administrator credentials
  [XXXXXX] failed to connect to the remote server XXXXX with the following
  error message: the client cannot connect to the specified destination in the
  request. Verify that the service on the destination is running and that he accepts the
  applications. Consult the logs and documentation for running management service
  on the destination, most IIS or WinRM. If the destination is the WinRM
  service, run the following command on the destination to analyze and configure the
  WinRM service: "winrm quickconfig". For more information, see the
  about_Remote_Troubleshooting help topic.
  + CategoryInfo: OpenError: (XXXXX:String)], PSRemotingTranspo
  rtException
  + FullyQualifiedErrorId: CannotConnect, PSSessionStateBroken

  # Outgoing connection is fine because I can connect to a different machine here. However incoming connection does not work

  # Tried several things like "Enable-PSRemoting - Force." and it starts Properperly

  # And since I put the machine in workgroup, as well run "Set-Item WSMan: \localhost\Client\TrustedHosts * ' (it is running successfully as well)

  # Infact WinRM QuickConfig will not work.

  # And tried with and without firewall. and also applied several patches, but has not solved the problem

  Please notify

  Original title: WinRM

  This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)
  http://social.technet.Microsoft.com/forums/en-us/home s/fr-U.S./Accueil
  http://social.msdn.Microsoft.com/Forum
  
  
  If you give us a link to the new thread we can point to some resources it

• problem with WiFi connectivity with new Ipad Pro.  Unable to connect to the wifi at home.  My other devices (mini mac, iphone, iPad 2) all work fine on my wifi at home.  I am able to connect Ipad Pro wifi work.

  Problem with WiFi connectivity with new Ipad Pro.  Unable to connect to the wifi at home.  My other devices (mini mac, iphone, iPad 2) all work fine on my wifi at home.  I am able to connect Ipad Pro wifi work.

  On the Pro iPad, tap settings > general > reset > reset network settings

  You will need to re enter your Wi - Fi password.

  Then try to connect to your Wi - Fi network.

  If this does not help, more available in this support article suggestions > If your iPhone, iPad or iPod touch connects to a Wi-Fi network

• I'm locked out of my iphone5 not connected to my wifi at home and my home button does not work, any ideas on how to fix?

  I'm locked out of my iphone5 not connected to my wifi at home and my home button does not work, any ideas on how to fix?

  < re-titled by host >

  Take it to an Apple Store for repair or replacement.

• Firefox said it is unable to connect to the net but IE and the signal is strong

  Firefox has been great until this afternoon. Then all of a sudden it gave me an error message that he was "unable to connect." "" The laptop thinks it entirely connected wireless to the Homehub. I have been in contact with BT that kept me in line with IE and say that the problem is with Firefox. I uninstalled and reinstalled Firefox and I'm still getting the message that it is unable to connect. Help, please!
  PS Firefox works perfectly on my desk.

  One possible cause is security software (firewall) that blocks or limits Firefox or plugin-container process without informing you, possibly after the detection of changes (update) for the Firefox program.

  Delete all rules for Firefox in the list of permissions in the firewall and leave your firewall again ask permission to get full unlimited access to the internet for Firefox and the plugin-container and the update process.

  See:

  • https://support.Mozilla.com/kb/server+not+found
  • https://support.Mozilla.com/kb/firewalls

• Help. Unable to connect to wireless internet at home

  Hello

  I have a T410 of work that can not connect to my wifi at home. He has worked in the past, but now he's going to connect to my router but will be no internet or say limited connectivity / No.. It is a work computer, so there may be a few firewall issues (I am able to work from home, so it should be allowed).

  If this is detailed in another post please direct me.

  If you need more information, please let me know and if you could give me instructions on how to recover the said info (not computer illiterate, but no guru)

  Thank you in advance for your help!

  Best,

  Jay

  Hello j2534a, welcome to the Lenovo forums!

  Ask your administrator. I had the same problems. The firewall is the main problem I think.

  But that s a problem for your admin.

• Unable to connect on WIndows (Windows 7 Home Premium 64-bit)

  I have HP desk top (bought 3 years ago) with Windows 7 Home Premium.  Today, after the regular windows updates, my PC has rebooted and showed me to the login to the accounts screen 2 user (both are protected by Word).

  When I clicked on any of these accounts, he was asked to enter the password and tried to connect.  But he couldn't and showed me back to 2 accounts login screen user.

  I rebooted my system several times, but the situation is the same.

  Please help me solve this.

  Thank you best regards &,.

  Ludovic pokora

  Hi Ludovic,.

  Thanks for posting your query in Microsoft Community.

  We apologize for the inconvenience caused due to updates.

  I suggest that you want to run auto repair with installation media and see if it helps you repair system files or not. For the execution of the task, I suggest you to try the steps below and see if it helps.

  Method 1: When you use the recovery environment (Windows RE) to troubleshoot startup issues, first try the Startup Repair option in the System Recovery Options dialog box. If this does not resolve the problem, or if you have additional problems manually, use the Bootrec.exe tool.

  Because you cannot start the computer, you may need to create a bootable Windows installation media, and then do an auto repair, and if this does not help then you try to restore your computer to the previous date.

  Note: When you use system restore to restore the computer to a previous state, the programs and updates that you have installed are removed.

  If you are using Windows 7 then the link provided below might help you to download and create installation media.

  Download Windows 7 Disk Images (ISO files)

  Method 2: If the problem persists, try to rebuild the BCD by using the Bootrec.exe tool. To run the Bootrec.exe tool, you must start Windows recovery environment (Windows RE) . To do this, follow these steps:

  1. Place the Windows 7 installation disc in the disc drive, and then start the computer.
  2. Press a key when you are prompted. Select a language, a time, a currency, a keyboard or an input method, and then click Next.
  3. Click repair your computer.
  4. Click the operating system you want to repair, and then click Next.
  5. In the System Recovery Options dialog box, click command prompt.
  6. Type Bootrec.exe, and then press ENTER.

  See the following link for more information:

  How to use the Bootrec.exe tool in the Windows recovery environment to troubleshoot and repair startup issues in Windows

  http://support.Microsoft.com/kb/927392

  Method 3: If after performing the above steps, you are able to start the computer and access the desktop then try to Uninstall KB3097877 update if it is installed, and then reinstall it.

  Hope it would help. If problem persists always post back with the current state of your computer and the result of the proposed suggestion, we will be happy to help you.

• Unable to connect to the Web sites security and microsoft, but internet is not working properly

  Can anyone help?
  Now, this is getting very frustrating.
  I can connect to the internet and browse most Web sites. My email works fine but I can't connect to websites www.microsoft , Norton is 'unable to connect to the Live Update server, check the internet connection' and my media center can't find my internet connection.
  What is going on?
  I have a subscription to Norton who can't find any problems. I also downloaded onecare and trojan remover, returning with a clean report.
  Please help before I go out what remains of my hair.
  What about Frank

  Hello

  You can access Microsoft.com, McAffee.com, Symatec.com? Thinking you have a conficker.

  Check with this site
  http://www.confickerworkinggroup.org/infection_test/cfeyechart.html

  Alert on the Win32/conficker virus
  http://support.Microsoft.com/kb/962007

  Protect yourself from Conficker
  http://www.Microsoft.com/security/worms/Conficker.aspx

  How to remove the worm Downadup Conficker (Uninstall Instructions)
  http://www.bleepingcomputer.com/virus-removal/remove-Downadup-Conficker

  How to manually remove the Conficker worm
  http://www.411-spyware.com/Conficker-worm-removal#how-to-remove

  BDTool to remove
  http://www.bdtools.NET/

  -----------------------------------------------

  Run the malicious Microsoft removal tool, scan with Malwarebytes, Prevx to be sure you know all the
  malware involved and if necessary use UnHackMe.

  Start - type in the search box-> find MRT top - right on - click RUN AS ADMIN.

  You should get this tool and its updates via Windows Update - if necessary, you can download it here.

  Download - SAVE - go where go out you there - top - right click RUN AS ADMIN
  (Then run MRT as shown above.)

  Malicious removal tool from Microsoft
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=AD724AE0-E72D-4F54-9AB3-75B8EB148356&displaylang=en

  Malwarebytes - a scanner at the request - update on the updates tab and run whenever you think malware.
  http://www.Malwarebytes.org/

  Here are some free online scanners to help the

  http://www.eset.com/onlinescan/

  http://www.Kaspersky.com/virusscanner

  Other tests free online
  http://www.Google.com/search?hl=en&source=HP&q=antivirus+free+online+scan&AQ=f&OQ=&AQI=G1

  also install Prevx to be sure that it is all gone.

  Prevx - Home - free - small, fast, exceptional CLOUD protection, working with other security programs. It comes
  a scan only, VERY EFFICIENT, if it finds something to come back here or use Google to see how to remove.
  http://www.prevx.com/

  Choice of PCmag editor - Prevx-
  http://www.PCMag.com/Article2/0, 2817,2346862,00.asp

  --------------------------------------------

  Also do to the General corruption of cleaning.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Run checkdisk - schedule it to run at the next startup, then apply OK then restart your way.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -------------------------------------------------

  Run Malwarebytes when you can.

  IE - Tools - Internet Options - Advanced - tab click on restore, and then click Reset - apply / OK

  IE - Tools - Internet Options - Security - reset all Zones by default level - apply / OK

  Close IE

  IE - tools - manage Addons (for sure disable SSV2 if it is there, it is no longer necessary but Java always install
  "(and it causes problems - you never update Java to go back in and turn it off again)." Search for other possible problems.

  Windows Defender - tools - software explore - look for problems with programs that do not look right. Permit
  are usually OK and "unauthorized" are not always bad. If in doubt about a program to ask about it here.

  Could be that a BHO - BHOremover - free - standalone program, needs no installation, download and run - not all
  are bad, but some can cause your question. (Toolbars are BHO)
  http://securityxploded.com/bhoremover.php

  Startup programs
  http://www.Vistax64.com/tutorials/79612-startup-programs-enable-disable.html

  Don't forget to do:

  Logon as administrator

  Start - type in the search box-> COMMAND - find on the list above - CLICK RIGHT - RUN AS ADMIN

  Enter each of these one at a time and press ENTER after each

  ipconfig/flushdns

  nbtstat-r

  nbtstat - RR

  netsh int Reinitialis

  netsh int ip reset

  netsh winsock reset

  Reset
  ------------------------------------------------------

  Here are a few rootkits if it were a question:

  SpyDLL Remover - free
  http://securityxploded.com/spydllremover.php

  Advanced Windows Service Manager
  http://securityxploded.com/winservicemanager.php

  Run the Rootkit Revealer - free
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb897445.aspx

  UnHackme - trial
  http://www.Greatis.com/UnHackMe/

  This shows how to use UnHackme and includes a link to version 2.5 – use it as a guideline and current
  available as version above is 5.5
  http://safecomputing.umn.edu/guides/scan_unhackme.html

  IceSword - free
  http://www.AntiRootkit.com/software/IceSword.htm
  Instructions and pictorial
  http://securityxploded.com/IceSword.php
  Tutorial for use of IceSword
  http://translate.Google.com/translate?hl=en&SL=zh-CN&u=http://soft.zol.com.CN/2004/0803/145163.shtml&prev=/search%3Fq%3Dicesword%26hl%3Den%26lr%3D

  Revo Uninstaller - free
  http://www.revouninstaller.com/

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• TBird 31.5.0 to 31.6.0 update. Download now unable to connect. Have stopped/started TBird and even restarted Win7. Any suggestions?

  On the second PC, worked with Tbird 31.5.0. Advice needed to level. Started automatic level to 31.6.0. Immediately restart TBird, I received the message unable to connect to live.mozellamessaging.com instead of normal greeting on half lower the window. If I try to do a "get Messages", the following message at the bottom tells " pop.earthlink.net connection as it is so, but it just hangs there.»
  I restarted TBird and even rebooted the system Win7 nothing helps. I watched the TBird account settings and they seem OK. Any suggestions on where to start?

  Thank you. I checked Norton AV and changed the auto setting allow and which seemed to fix the problem.

• Unable to connect on the websites except Google and facebook

  I am currently unable to connect to all websites except Google or Facebook since yesterday. I did the basic check through the menu in SAFARI preferences with no result. Could someone help me in this matter?

  Thank you.

  Hello.

  If you have problems to open Web pages, take a look at these techniques proposed by Apple of troubleshooting.

  https://support.Apple.com/en-us/HT204098

  Go to the Safari menu (at the top right of your screen next to the Apple icon), choose 'Quit Safari'

  Press the "Shift" key and while holding this button on your unique keyboard, click the icon of Safari on your Dock.

  Open Safari - Preferences - Privacy - data to remove any Web site.

  Open the menu to go with the Option (Alt) key - library - key locate Safari folder and place it on your desktop. Restart your Mac, open Safari and delete the file from your desktop.

  Also, try the following steps:

  Restart your Mac.

  Try to start:

  -Stop your Mac

  -Wait until your computer turns off and after that press the power button

  -Just after you hear the startup tone, press in and hold the SHIFT key

  -Release the SHIFT key when you see a gray Apple sign and the progress under this sign bar

  -Once your Mac boot, restart dhcpd as you usually do.

  If this does not help, follow the instructions below:

  -Stop your Mac

  -Wait until your computer turns off and after that press the power button

  -Just after you hear the startup tone, press in and hold the SHIFT key

  -Release the SHIFT key when you see a gray Apple sign and the progress under this sign bar

  -Once you see office, start a scan Disk Utility to detect and repair file system errors (remember to choose your primary hard drive)

  -Click on the disc to check, then, if requested to solve the problems on the repair disk

  -After that click on verify disk permissions, and then click Repair disk permissions

  -Once the process is complete, stop your Mac and turn it on again after 30 seconds

  I hope this helps!

• Version 20.01 is "Unable to connect" while the previous Version 19.02 works great!

  My work computer which runs Windows XP Pro with Service pack 3 and beyond has been upgrade FF worm. 20.01 this afternoon and is "unable to connect". It worked very well on the version previous minutes before it has been updated! Nothing has changed in my network connections and my firewall settings! I'm writing this on a Windows 7 computer that is currently running FF worm. 20.02 that works well! I have another Windows XP Pro computer that is currently running FF Ver, 19.02 and there is a "Software Update" window on the screen asking me to update this computer to 20.01 worm. FF. I clicked on "Ask later" in fear that it will have the same problem "unable to connect"! Help!

  It is possible that your security (firewall, antivirus) software blocks or limit Firefox or the process of plugin-container without you inform, possibly after the detection of changes (update) for the Firefox program.

  Delete all rules for Firefox and the plugin-container in the permissions list in the firewall and leave your firewall again ask permission to get full unlimited access to the internet for Firefox and the plugin-container and the update process.

  See:

  • https://support.Mozilla.org/KB/server+not+found
  • https://support.Mozilla.org/KB/firewalls

• Unable to connect my remote App for apple TV 4

  • Apple TV 4
  • IPhone 6 with the latest installed IOS
  • The two devices connected to the same WIFI network

  I tried to connect my application to remotely installed on my Iphone to my apple TV 4 6. I tried with the 'home sharing' option and the 'manual' without success.

  What should I do next?

  Hello

  It couldn't be you.  It could be Apple.  My remote with the same kit and the software that you have worked on Saturday.  Today the AppleTV as missing but my old AppleTV is still there and I can still see iTunes.  In addition, I have several iPads different generation with my family and the AppleTV has disappeared, too.  And none of my devices are recognized by the new AppleTV as pairable.  Could be however the AppleTV.

• Unable to connect to remote via windows VPN 8.1 or higher apps

  I have a problem with clients who have their RDP upgrade over version 7.1 connect to our remote applications.

  I can see the event on the event viewer of the broker connection that the client was allowed to connect to a host, but the connection cannot be established.

  Anyone running RDP v 7.1 can connect without a problem.

  It seems only in fact anyone who isn't within our office.

  They would be on a different subnet

  Ex:

  Office 10.0.40. *.

  10.0.129 * remote desktop

  We don't have this problem with the only connections to our remote applications regular Remote Desktop connection.

  Servers running the hosts and the broker for connections are all r2 server 2012

  Range of client computers in windows 7 to windows 10

  This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)
  http://social.technet.Microsoft.com/forums/en-us/home s/fr-U.S./Accueil
  http://social.msdn.Microsoft.com/Forum
  
  
  If you give us a link to the new thread we can point to some resources it

• Unable to connect to remote vpn IPSec (Error 412)

  Hello

  Try to configure the IPSec vpn connection but error 412: the remote peer not responding.

  Router Cisco is directly connected to the internet using the dialer interface.

  So far, I tried the following:

  Disabled Windows Firewall

  IPSec over TCP ticket (received error 414)

  Permit to debug crypto ISAKMP and IPSEC (no illustrated newspaper)

  Newspapers enabled on the version of client VPN 5.0.01.0440

  (Impossible to establish Phase 1 SA with server 'xxxxxxxxx' due to the 'DEL_REASON_PEER_NOT_RESPONDING')

  The router configuration:

  version 12.4

  horodateurs service debug datetime msec

  Log service timestamps datetime msec

  encryption password service

  !

  !

  boot-start-marker

  boot-end-marker

  !

  !

  AAA new-model

  !

  !

  AAA authentication login default local

  AAA authentication login usr_auth local

  AAA authorization grp_auth LAN

  !

  AAA - the id of the joint session

  !

  resources policy

  !

  MMI-60 polling interval

  No mmi self-configuring

  No pvc mmi

  MMI snmp-timeout 180

  IP subnet zero

  no ip source route

  IP cef

  !

  !

  No dhcp use connected vrf ip

  DHCP excluded-address IP 192.168.3.1 192.168.3.10

  !

  pool IP dhcp pool Classes

  network 192.168.3.0 255.255.255.0

  default router 192.168.3.1

  Server DNS XXXXXX xxxxxxxxxxx

  !

  !

  no ip bootp Server

  no ip domain search

  IP domain name xxxxxxxxx

  property intellectual ssh time 80

  VPDN enable

  !

  !

  !

  !

  !

  username 7 password xxxxxx xxxxx

  !

  !

  !

  crypto ISAKMP policy 10

  BA aes

  preshared authentication

  Group 5

  !

  ISAKMP crypto client configuration group client_cfg

  XXXXXXX key

  DNS xxxxxxx

  pool vpn_pool

  ACL 120

  Max-users 2

  Profile of isakmp crypto vpn-ike-profile-1

  client_cfg group identity match

  client authentication list usr_auth

  ISAKMP authorization list grp_auth

  client configuration address respond

  virtual-model 2

  !

  !

  Crypto ipsec transform-set encrypt-method-1 esp - aes esp-sha-hmac

  !

  Crypto ipsec VPN-profile-1 profile

  the transform-set encrypt-method-1 value

  !

  !

  !

  !

  interface Loopback0

  the IP 10.0.0.1 255.255.255.0

  !

  ATM0 interface

  no ip address

  No atm ilmi-keepalive

  DSL-automatic operation mode

  !

  point-to-point interface ATM0.1

  no link-status of snmp trap

  PVC 8/35

  PPPoE-client dial-pool-number 1

  !

  !

  interface FastEthernet0

  no ip address

  automatic speed

  !

  interface FastEthernet1

  Shutdown

  !

  interface FastEthernet2

  switchport access vlan 2

  !

  interface FastEthernet3

  switchport access vlan 3

  !

  interface FastEthernet4

  switchport access vlan 4

  half duplex

  !

  tunnel type of interface virtual-Template2

  IP unnumbered Loopback0

  IP nat inside

  IP virtual-reassembly

  ipv4 ipsec tunnel mode

  Profile of tunnel ipsec VPN-profile-1 protection

  !

  interface Vlan1

  no ip address

  !

  interface Vlan2

  192.168.1.100 IP address 255.255.255.0

  IP nat inside

  IP virtual-reassembly

  IP tcp adjust-mss 1452

  !

  interface Vlan3

  address 192.168.3.1 IP 255.255.255.0

  IP access-group 101 in

  IP nat inside

  IP virtual-reassembly

  IP tcp adjust-mss 1452

  !

  interface Vlan4

  192.168.4.1 IP address 255.255.255.0

  IP nat inside

  IP virtual-reassembly

  IP tcp adjust-mss 1452

  !

  interface Dialer1

  the negotiated IP address

  IP mtu 1492

  NAT outside IP

  IP virtual-reassembly

  encapsulation ppp

  Dialer pool 1

  Dialer-Group 1

  PPP authentication pap callin

  PPP pap sent-name of user password xxxxxx xxxxxxx 7

  !

  local pool 10.0.0.10 IP vpn_pool 10.0.0.20

  IP classless

  IP route 0.0.0.0 0.0.0.0 Dialer1

  !

  no ip address of the http server

  no ip http secure server

  the IP nat inside source 1 list overload of the Dialer1 interface

  IP nat inside source static tcp 192.168.1.1 25 25 Dialer1 interface

  IP nat inside source static tcp 192.168.1.1 80 80 Dialer1 interface

  IP nat inside source static udp 192.168.1.1 53 53 Dialer1 interface

  IP nat inside source static tcp 192.168.1.1 53 53 Dialer1 interface

  IP nat inside source static tcp 192.168.1.1 interface 1000 Dialer1 1000

  IP nat inside source static tcp 192.168.1.1 interface 443 443 Dialer1

  IP nat inside source static tcp 192.168.1.1 interface Dialer1 143 143

  !

  WAN-IN extended IP access list

  refuse the ip 0.0.0.0 0.255.255.255 everything

  deny ip 10.0.0.0 0.255.255.255 everything

  deny ip 100.64.0.0 0.63.255.255 all

  deny ip 127.0.0.0 0.255.255.255 everything

  deny ip 169.254.0.0 0.0.255.255 everything

  deny ip 172.16.0.0 0.15.255.255 all

  deny ip 192.0.0.0 0.0.0.255 any

  deny ip 192.0.2.0 0.0.0.255 any

  deny ip 192.168.0.0 0.0.255.255 everything

  deny ip 198.18.0.0 0.1.255.255 all

  deny ip 198.51.100.0 0.0.0.255 any

  deny ip 203.0.113.0 0.0.0.255 any

  refuse the 224.0.0.0 ip 31.255.255.255 all

  allow an ip

  !

  access-list 1 permit 192.168.1.0 0.0.0.255

  access-list 1 permit 192.168.3.0 0.0.0.255

  access-list 1 permit 192.168.4.0 0.0.0.255

  access-list 101 deny ip 192.168.3.0 0.0.0.255 192.168.1.0 0.0.0.255

  access list 101 ip allow a whole

  access ip-list 120 allow a whole

  !

  control plan

  !

  !

  Line con 0

  exec-timeout 5 0

  line to 0

  exec-timeout 5 0

  password 7 xxxxxxxxxxxx

  line vty 0 4

  exec-timeout 5 0

  password 7 xxxxxxxxxxxx

  preferred transport ssh

  entry ssh transport

  line vty 5 15

  exec-timeout 5 0

  password 7 xxxxxxxxxxxx

  preferred transport ssh

  entry ssh transport

  !

  end

  I don't get any password prompt, so I guess there is a misconfiguration. Would appreciate if you can help with this.

  Thank you

  The 10.0.0.x pool is configured properly. Just change the NAT to traffic between 192.168.1.x, 3.x, and 4.x are exempt in NAT, where the above change config.

  Your split tunnel ACL says allow an entire ip, so please change it to the following:

  access-list 120 allow ip 192.168.1.0 0.0.0.255 10.0.0.0 0.0.0.255

  access-list 120 allow ip 192.168.3.0 0.0.0.255 10.0.0.0 0.0.0.255

  access-list 120 allow ip 192.168.4.0 0.0.0.255 10.0.0.0 0.0.0.255