Unable to connect with the WRT54GLS interface with v34.0.5

Similar Questions

• Unable to connect to the web interface TCS

  Hello, I'm having a problem with a TC who left the factory of S5.3 current version. I can RDP into the Windows operating system without problem and access the web page of the OS on the port 8098 management no problem, but if I try to connect to the web application interface I get a name of user and password error.  any IDE on what is causing the problem?  the server was running fine until after a reboot.  Thank you!

  Hi Patrick, http:///tcs/#page:login&rescue:true method is used for the local administrator to log in if for some reason any when LDAP authentication is configured on TCS and local users cannot connect.

  ARO

  Mahesh Adithiyha

• NAS200: Unable to connect to the Web Interface

  Just set up my new NAS200.  I could install two (2-1 TB disks, RAID1) disks and set the IP address.  However, I can not connect in the administration area of the drive to set up users, shared directories, etc..  The doc on the CD has no value.

  When I run the initial Setup, I wonder for a pawword.  I enter the password that I entered in initial Setup, and I get.  However, this leaves me not do anything other that configure stuff of basic training.

  Someone at - it suggestions?

  Thank you.

  mechanism

  I was able to eventually get through the web interface.  It turns out that the system was not ready yet.  I have 2 1 TB drives in a RAID-1 configuration, and it took the best part of 2 days to get into shape.

  Once I was, I updated the firmware, and things seem to be working very well now.

  mechanism

• Unable to connect to the interface user APIC

  Hello

  I erased the APIC servers configuration using "eraseconfig setup. I did this several times before and I've never had problems.

  Today, I followed the same process as before and rebuilt the cluster, but now I am unable to connect to the user interface. I get the following error of three servers:

  "REST datastore user authorization endpoint is not initialized - check fabric composition State of this node of tissue.

  Thank you

  Ben

  Ben,

  Access the console or the kvm to each controller APIC MMIC.

  Please try to connect to all the APICs 3 using the 'rescue-user' user name.  There should be no password because you have disabled the configuration...

  After scoring in each APIC, run and screen captures the output of the command 'acidiag avread'.

  Please reach the exits in your answer or check and verify the name of "tissue" on each APIC. They must match.  If not, you will need to "configuration eraseconfig" each APIC again and configure the APICs via the initial configuration script.

  Thank you

  T.

• My ZTE open C unable to connect to the wlan with 63-signs-hex key.

  Hello

  my C open from ZTE unable to connect to the wlan with WPA2-PSK and a 63 sign hex key. When I create a 2. ESSID with WPA2-PSK a sentence normal, everything's fine.

  Oliver

  Hi OliverwithZTE,

  I understand that you have connection problems to your network WPA2-PSK.

  Unfortunately, WPA2-PSK is currently not supported on Firefox OS version 1.3. Only WPA-TKIP and WPA2-AES are supported.

  -Ralph

• problem with WiFi connectivity with new Ipad Pro.  Unable to connect to the wifi at home.  My other devices (mini mac, iphone, iPad 2) all work fine on my wifi at home.  I am able to connect Ipad Pro wifi work.

  Problem with WiFi connectivity with new Ipad Pro.  Unable to connect to the wifi at home.  My other devices (mini mac, iphone, iPad 2) all work fine on my wifi at home.  I am able to connect Ipad Pro wifi work.

  On the Pro iPad, tap settings > general > reset > reset network settings

  You will need to re enter your Wi - Fi password.

  Then try to connect to your Wi - Fi network.

  If this does not help, more available in this support article suggestions > If your iPhone, iPad or iPod touch connects to a Wi-Fi network

• Unable to connect to the HP ePRINT with Color LaserJet Pro 400 M475dw MFP website

  LaserJet Pro 400 color multifunction m475dw-Just installed. Print, scan, copy and fax all works fine! use of WiFi

  Using IMAC OS 10.8.2 with all updates

  Netgear DGN2200v3 router using

  Printer not connect to the HP ePrint website

  Printer connects using Hp and profile for fax set up etc.  But the "HP Web Services" article when enrecorded and hit the Activate button - it does not connect to the site - it seems just to refresh.

  "If I try to connect thro the printer not the imac and try to activate the web services, it says" connection "on the screen BUT after a few minutes of trying - so says" CONNECTION ERROR - the printer is unable to connect to the service. Check the internet connection

  ANY IDEAS - HAVE I MISSED SOMETHING?

  Thank you very much

  I try to pull up the built-in web server (EWS) by entering the IP address of the printer in a browser and set a static IP & DNS address.

  The information for the default gateway, subnet mask and IP address can be accessed from the Setup menu on the front panel, go to settings > reports > network summary and it will print off the coast.

  Once you entered the IP address in a browser and have the EWS pulled up, go to the tab above titled "Networking". Then click on IPv4 in the left column; who will bring to the top of the address configuration page.  Place the manual radio button and fill in the IP address, the default gateway and the subnet mask with the information from the report. You don't fill the part entitled WINS server, which can be left alone.

  You will then want to fill in the DNS of the page part, the favorite should be set to 8.8.8.8 and the alternative/secondary must be set to 8.8.4.4. Then click 'apply '.

  Power cycle the printer. Turn off the power, wait 30 seconds and then turn it back on. Once it is fully operational, try again to connect to web services.

• Unable to connect with the PC tab

  I bought a Ubislate android 7 C + from Datawind, but unable to connect with the computer

  Burnersalvation,

  To provide the proper resolution, I would need more information on your side.

  1. which version of the operating system are you using?

  2. what happens when you try to connect to the tab?

  3. How do you connect tab to the computer?

  To connect to Android Ubislate to the computer, it may require some software to install on the computer provided by the manufacturer of the tab. Then I suggest you to contact the manufacturer of the tab to get help on this issue.

  Check out the link:

  http://www.ubislate.com/contact/index.html

  Hope this information helps. If you need more assistance or information on this question, reply to this post. I'll be happy to help you.

• I am unable to connect to the Linksys WRT54G Router with wired connection to Office XP.

  My two laptops (XP and a Win7) will be connected to the router wireless and wired (ethernet). When it is plugged directly into the DSL modem, the Office connects and works very well. This problem started when I had to replace the DSL modem.

  I inherited this problem for my elderly mother... and it all started because they gave me the router password wrong, who now works (router has been reset) on two laptops, but when connected, the Office doesn't even show a light of connection on the router except during startup. I no longer get a window of logon passwork for the router, and I am unable to connect/ping the router in the office. (192.168.1.1)

  I would like to clarify a few things.

  1. two laptops work fine with cable connections and wireless through the WRT54G.

  2 desktop PC, which has only a wired connection, does not connect successfully.

  3. the symptoms of the failure of the desktop connection to are that the link on the router at the start light flashes during initialization of the PC but then will Dim.

  4. when the desktop PC trying to connect to the internet, it fails.

  5 when the desktop PC try to connect to the administration WRT54g page it fails.

  6. when the desktop computer try PIING the router at 192.168.1.1 IP address it fails.

  These points are correct?

  Assuming this is correct, open a command prompt and type

  IPCONFIG/ALL

  The output of the command should provide some information about the current state of the network connection.

  It would be useful that you posted this here release.

  The absence of a link light can be your main symptom and may be due to several reasons. He probably has an associate status "media disconnected" in IPCONFIG for the network connection.

  This could be caused by a bad network cable or a network connection disabled in the properties of the network on the PC. Small jets knowing the ot IPCONFIG output is would help more.

  Post this info if you can.

  Good luck

• When I use the Client for NFS provided by Windows 7, I'm unable to connect. The "mount \\ip address\share Z:" command fails with the error code "the path not found network".

  Identification of customer's Windows 7 NFS UID GID information

  I am trying to connect to the Windows 7 Client NFS on a server running on a computer (VxWorks) NFS.  I am able to properly connect Client NFS software by a 3rd party on the NFS server.  However, when I use the Client for NFS provided by Windows 7, I am unable to connect.  The \\ip address\share Z: mount"command fails with the error code"the path not found network ".  I can't do a ping of the computer running the NFS server.

  The NFS Client operating system: Windows 7 Ultimate, 64-bit

  Data captured by Wireshark

  MOUNT V1 EXPORT call 3rd party client
  Identification information Flavor: AUTH_UNIX (1)
  Length: 32
  Stamp: 0xc7065970

  Machine name: PC
  UID: 1000
  GID: 1000

  MOUNT V1 EXPORT appeal of the NFS client
  Identification information Flavor: AUTH_NULL (0)
  Length: 0

  It seems that the credentials of NFS Client are not correct.  How can I change the flavor of AUTH_UNIX and the UID and GID to 1000?

  Hello VDAEMP,

  As Eddie and Sudarshan has said, the Microsoft Answers community focuses on issues and problems related to the consumer environment. Please join the public IT pro TechNet forums below:
  TechNet - Windows Server
   
  Thank you

• Unable to connect with the Mac computer?

  Unable to connect with the Mac computer?

  Please read https://forums.adobe.com/thread/1499014

  -try some steps such as changing browsers and disable your firewall

  -also clear the cache of your browser if you start with a fresh browser

  -Run "Difficulty Host File" option https://helpx.adobe.com/creative-cloud/kb/cc-cleaner-tool-installation-problems.html

  http://myleniumerrors.com/installation-and-licensing-problems/creative-cloud-error-codes-w ip.

  https://helpx.Adobe.com/creative-cloud/KB/creative-cloud-desktop-application-failed.html

  http://helpx.Adobe.com/creative-cloud/KB/failed-install-creative-cloud-desktop.html

• I can't import my script (film) into Adobe Story. The error message says that I am unable to connect to the Adobe servers. Is this a problem with the Adobe?

  I can't import my script (film) into Adobe Story. The error message says: I am unable to connect to the Adobe servers. Is this a problem with the Adobe?

  Yes and no it seems that if the file is a .doc or .pdf, that it does not load properly. But if I bring him in a Final Draft format, it works perfectly.

  Adam

  Sent from my iPhone

• My cloud of Adobe installer is unable to connect to the animated. No problems with internet... Help, please

  My cloud of Adobe installer is unable to connect to the animated. No problems with internet... Help, please

  Hello

  Thank you for using https://helpx.adobe.com/x-productkb/policy-pricing/activation-network-issues.html > and all the steps in "troubleshooting connectivity issues.

  If necessary, and for any other question, click on through http://helpx.adobe.com/contact.html and so "open" Please use the chat, I to can I part had the best experiences. An employee of Adobe Preran I quote: the chat button is enabled as soon as there is an available to help agent.

  Hans-Günter

• migrate storage fails with 'unable to connect to the host.

  I'm trying to migrate storage of a virtual machine to a different data store. (on the same san)

  When I start work, I see the task:

  Moving the virtual machine / status 'in process '.

  After 10 minutes, I get 2 pop-up windows:

  -

  ---

  Error

  -

  ---

  Unable to connect to the host.

  -

  ---

  Ok

  -

  ---

  I tried to move the storage of another virtual machine, but I got the same error.

  Also tried a different vmhost (but same cluster), but also the same error.

  When you try to a host in a different cluster, it works without problem (same san/store data used in the cluster where I got the errors)

  There is no difference in the profile of security on the host computers.

  Any tips?

  Logfile attached (vpxd - 353.log) when I was running the migrate storage.

  Part of the error:

  2009-11-03 16:49:07.035 02464 info "App" (1257263347020035) VMotion began

  2009-11-03 16:58:35.903 02464 error "App" (1257263347020035) VMotion failed: vim.fault.HostConnectFault

  When it works ok:

  2009-11-03 17:29:49.470 02456 info "App" (1257265789470153) VMotion began

  Hello.

  See KB 1010837.

  Good luck!

• Unable to connect to the virtual disk Service, Virtual Disk Manager Interface not registered

  I installed Windows 7 Ultimate on this laptop as a new installation about six months ago.  Since then, I don't think I ever ran diskmgmt.  Today, I joined a new external hard drive usb, it reported the drivers installed fine, but then the installation bombed at the beginning.  I went to verity, what had happened and has run diskmgmt.msc (as an administrator), but she came back with the message "Unable to connect to the virtual disk Service" and also a small OK msgbox appeared with the title "Virtual Disk Manager" and the "Interface not registered" message

  I disconnected the USB hard drive and tried again diskmgmt, but no change.

  I restarted in safe mode, tried diskmgmt, but no change.

  I ran sfc/scannow, but it has reported that it found no errors.

  I checked that the virtual disk service has been configured as a textbook in services.msc, and event viewer showed that when I ran diskmgmt he started VDS and then stopped VDS.

  I tried again, but still not like before.

  Is there some dll I can't regsrv32?

  Thank you

  Marc

  Hello

  I suggest you to return the items for the following responses from Microsoft, he says same issues with trying the troubleshooting steps and check if it helps.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-hardware/cant-start-disk-management-unable-to-connect-to/31898500-9d84-4CB5-9ba3-c1f42e3b1ace

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-hardware/problems-with-Vista-after-unplugging-by-external/093f1660-160F-478f-b81a-493e963ffd9a

  http://TechNet.Microsoft.com/en-us/library/cc771775.aspx

  Note: it also applies to Windows 7.

  Hope the information is useful.

• Unable to connect with iTunes Store

  Apple tv sends the message unable to connect with iTunes Store

  Are you sing the correct settings of the location and the region