Unable to connect to the web interface TCS

Similar Questions

• NAS200: Unable to connect to the Web Interface

  Just set up my new NAS200.  I could install two (2-1 TB disks, RAID1) disks and set the IP address.  However, I can not connect in the administration area of the drive to set up users, shared directories, etc..  The doc on the CD has no value.

  When I run the initial Setup, I wonder for a pawword.  I enter the password that I entered in initial Setup, and I get.  However, this leaves me not do anything other that configure stuff of basic training.

  Someone at - it suggestions?

  Thank you.

  mechanism

  I was able to eventually get through the web interface.  It turns out that the system was not ready yet.  I have 2 1 TB drives in a RAID-1 configuration, and it took the best part of 2 days to get into shape.

  Once I was, I updated the firmware, and things seem to be working very well now.

  mechanism

• Unable to connect to the web services server

  Unable to connect to the web services server.  It is a common error that you might see if you try to enable web services.  If you receive this message, try the following steps.

  For Officejet printers

  1. open the internet browser type printer IP address.

  2 should bring you to the status of the printer page.

  3. Select the tab network at the top.

  4. left side select IPv4 under wireless.

  5. under DNS address Configuration select manual DNS server.

  6. for favorite enter 8.8.8.8

  7. for alternate enter 8.8.4.4

  8. Select apply. You can get a warning saying that this could break the connection which is very good.

  9. turn the printer off for about 30 seconds and then try to enable web services.

  For Photosmart printers

  1. Enter the printer's IP address in a browser.

  2 Select the network at the top of the page.

  3. on the left, select network.

  4. Select Network (IP) address

  5. select manual DNS server

  a. manual Preferred DNS should read 8.8.8.8

  b. alternate DNS server should read. 8.8.4.4

  6. Select apply you could get a fair warning select OK

  I hope this helps!

• Unable to connect to the web proxy/services

  Unable to connect to the web proxy/services used for officejet pro 8600 as well as using verizon fios actiontec router.  I tried wireless and ethernet.  Connectivity seems good.

  Resolved.  Port forwarding blocked by another application of verizonwebcamera problem.

• HP 8500 replaced, software does not detect printer even though I can't ping / connect to the web interface

  Windows 7 Pro 64

  Reference Dell

  Printer connected via ethernet

  software worked well until the printer has been replaced by HP under warranty

  in the new device, the screen of the wizard to set the time/language etc.

  Software HP does not detect the device and so I can not use all the features.

  I can connect to the printer via IP and also tried to put the TCP/IP port with printer static IP. Can I print using this, but the software "suite" does not detect the printer.

  Removed all software, cleaned the registry, removed the IP port, re-installed the software, does still not detect printer.

  Installed HP printer diags and it passes all the tests, but the suite software HP will always be NOT detect printer.

  Tried without firewall, tried with, still can ping printer, connect to the web interface, the static value, always the software does not detect the printer... so whats left to please other than an another replacement warranty which is used to solve the problem, as it is definitely bad coding in the suite.

  I also tried downloading drivers/full later on the HP site.

  Note that all windows updates are met, reconstruction is out of the question that it is a machine of the company and would almost take me 3-4 days to replace all the software on it (Sage, DW, COFFEE, HMRC).

  Hi-Dillion, Declan

• Linksys spa3102, unable to connect to the web-based utility.

  I have a problem... try to configure my spa3102 voip router, I can't connect you to the basic utility web (192.168.0.1/admin/advanced) page that he asked me to in the installation guide.

  a reapears of error "404-File not found" every time.

  Help, please

  first of all, make sure that your computer is connected to the LAN port on the back of the SPA3102 - then, click Start > run > type cmd > click OK > type ipconfig > hit Enter - glance to the DEFAULT GATEWAY - use to access the web interface of the SPA3102

  ex. If the default gateway as 192.168.1.1 type http://192.168.1.1 in the address bar of your IE - you can then click admin on the upper right of the screen and then click on advanced, also on the upper right of the screen

  * Sometimes the IP address of SPa3102 changes to a different address, especially if the device when you connect the WAN port has the same IP address which is 192.168.0.1

• WRT160NL cannot connect to the web interface after firmware update

  I've updated the firmware to unofficial http://mirwifi.org/download/fw/WRT160NL/wrt160nl-0.1.3-pre5.bin and since then I can not connect to the router through the web interface. What can I do? Is it possible to update the firmware to the official without web interface? Thanks in advance for any help.

  The router's default IP address is 192.168.1.1. Try to ping the IP address of the router and check if you get answers from the router.

  Open the Internet browser and in the address bar type http://192.168.1.1. See if you can open the router configuration page.

  If this does not work then you can try to update the official firmware on the router using the TFTP.exe file.

  Disable the firewall on your computer. Connect the computer to the router with the Ethernet cable.

  (1) download the official firmware file from the site Web of Linksys router. Save it to your computer.

  (2) download the tftp site Web of Linksys. Follow this link to search for the file tftp. You'll find downloads for router BEFW11S4. Select the version 3.2 hardware and download the installation wizard. Save it to your computer.

  (3) run the installation wizard. In the server box, type the IP address of your router. In the password box, type the password of the router. Default password for the router is admin. Find the file of the official firmware you have already downloaded and click on upgrade.

  See if it works.

  After upgrading the Firmware on the router, it is recommended that you must reset the router and reconfigure.

  Press and hold the reset button on the router for 30 seconds. Release the reset button and wait 10 seconds. Power cycle the router and reconfigure.

• Unable to connect to the Web sites security and microsoft, but internet is not working properly

  Can anyone help?
  Now, this is getting very frustrating.
  I can connect to the internet and browse most Web sites. My email works fine but I can't connect to websites www.microsoft , Norton is 'unable to connect to the Live Update server, check the internet connection' and my media center can't find my internet connection.
  What is going on?
  I have a subscription to Norton who can't find any problems. I also downloaded onecare and trojan remover, returning with a clean report.
  Please help before I go out what remains of my hair.
  What about Frank

  Hello

  You can access Microsoft.com, McAffee.com, Symatec.com? Thinking you have a conficker.

  Check with this site
  http://www.confickerworkinggroup.org/infection_test/cfeyechart.html

  Alert on the Win32/conficker virus
  http://support.Microsoft.com/kb/962007

  Protect yourself from Conficker
  http://www.Microsoft.com/security/worms/Conficker.aspx

  How to remove the worm Downadup Conficker (Uninstall Instructions)
  http://www.bleepingcomputer.com/virus-removal/remove-Downadup-Conficker

  How to manually remove the Conficker worm
  http://www.411-spyware.com/Conficker-worm-removal#how-to-remove

  BDTool to remove
  http://www.bdtools.NET/

  -----------------------------------------------

  Run the malicious Microsoft removal tool, scan with Malwarebytes, Prevx to be sure you know all the
  malware involved and if necessary use UnHackMe.

  Start - type in the search box-> find MRT top - right on - click RUN AS ADMIN.

  You should get this tool and its updates via Windows Update - if necessary, you can download it here.

  Download - SAVE - go where go out you there - top - right click RUN AS ADMIN
  (Then run MRT as shown above.)

  Malicious removal tool from Microsoft
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=AD724AE0-E72D-4F54-9AB3-75B8EB148356&displaylang=en

  Malwarebytes - a scanner at the request - update on the updates tab and run whenever you think malware.
  http://www.Malwarebytes.org/

  Here are some free online scanners to help the

  http://www.eset.com/onlinescan/

  http://www.Kaspersky.com/virusscanner

  Other tests free online
  http://www.Google.com/search?hl=en&source=HP&q=antivirus+free+online+scan&AQ=f&OQ=&AQI=G1

  also install Prevx to be sure that it is all gone.

  Prevx - Home - free - small, fast, exceptional CLOUD protection, working with other security programs. It comes
  a scan only, VERY EFFICIENT, if it finds something to come back here or use Google to see how to remove.
  http://www.prevx.com/

  Choice of PCmag editor - Prevx-
  http://www.PCMag.com/Article2/0, 2817,2346862,00.asp

  --------------------------------------------

  Also do to the General corruption of cleaning.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Run checkdisk - schedule it to run at the next startup, then apply OK then restart your way.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -------------------------------------------------

  Run Malwarebytes when you can.

  IE - Tools - Internet Options - Advanced - tab click on restore, and then click Reset - apply / OK

  IE - Tools - Internet Options - Security - reset all Zones by default level - apply / OK

  Close IE

  IE - tools - manage Addons (for sure disable SSV2 if it is there, it is no longer necessary but Java always install
  "(and it causes problems - you never update Java to go back in and turn it off again)." Search for other possible problems.

  Windows Defender - tools - software explore - look for problems with programs that do not look right. Permit
  are usually OK and "unauthorized" are not always bad. If in doubt about a program to ask about it here.

  Could be that a BHO - BHOremover - free - standalone program, needs no installation, download and run - not all
  are bad, but some can cause your question. (Toolbars are BHO)
  http://securityxploded.com/bhoremover.php

  Startup programs
  http://www.Vistax64.com/tutorials/79612-startup-programs-enable-disable.html

  Don't forget to do:

  Logon as administrator

  Start - type in the search box-> COMMAND - find on the list above - CLICK RIGHT - RUN AS ADMIN

  Enter each of these one at a time and press ENTER after each

  ipconfig/flushdns

  nbtstat-r

  nbtstat - RR

  netsh int Reinitialis

  netsh int ip reset

  netsh winsock reset

  Reset
  ------------------------------------------------------

  Here are a few rootkits if it were a question:

  SpyDLL Remover - free
  http://securityxploded.com/spydllremover.php

  Advanced Windows Service Manager
  http://securityxploded.com/winservicemanager.php

  Run the Rootkit Revealer - free
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb897445.aspx

  UnHackme - trial
  http://www.Greatis.com/UnHackMe/

  This shows how to use UnHackme and includes a link to version 2.5 – use it as a guideline and current
  available as version above is 5.5
  http://safecomputing.umn.edu/guides/scan_unhackme.html

  IceSword - free
  http://www.AntiRootkit.com/software/IceSword.htm
  Instructions and pictorial
  http://securityxploded.com/IceSword.php
  Tutorial for use of IceSword
  http://translate.Google.com/translate?hl=en&SL=zh-CN&u=http://soft.zol.com.CN/2004/0803/145163.shtml&prev=/search%3Fq%3Dicesword%26hl%3Den%26lr%3D

  Revo Uninstaller - free
  http://www.revouninstaller.com/

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• Not able to connect to the web interface for a C20

  I have a C20 running 6.0.1 and impossible to access the web interface. I checked all the IP settings using the remote and have achieved nothing out of the ordinary. I am able to ping the C20 and get the cisco logo on the tab of the internet Explorer, but cannot connect. Someone at - it experianced this before?

  Hi Justin,

  Where you can do telnet/ssh to the codec and only the web interface does not come to the top, well want to check HTTP and HTTPS mode and turn it on according to the requirement;

  xConfiguration HTTP NetworkServices Mode: on

  xConfiguration HTTPS NetworkServices Mode: on

  In addition, it is registered on any CUCM?

• Unable to connect to the web.

  I have an Inspiron One 2305. Yesterday morning, everything was fine. Before noon I couldn't connect to the web. The network connection shows that I am connected. I always get an error "unable to connect to the page. I ran anti-virus and malware. Still nothing. Do a system restore I can connect on a single page. Try to leave this page and I get the same error. Can someone give me an idea?

  At this point you can repair or reinstall Win 7. Make sure that all of your personal files are stored on a medium firstexternally.

  To do a repair, you will need your reinstall Dell Win 7 drive. Start with a hard disk check

  • Click Start > run
  • Type: chkdsk c: /f
  • Click OK
  • Accept offer to run chkdsk at the next startup, and then restart. CHKDSK runs before Windows loads. Be patient as this can take some time, depending on the size of your hard drive.

  Unlikely that chkdsk will solve the network problem, but check it anyway...

  Then run a check of Windows system (CFS) files:

  • Click Start > run
  • Type: sfc/scannow
  • Click OK
  • Insert the Dell Windows reinstallation disc, if/when requested
  • Restart when done
  • Check again networking

  If this does not help, make sure that your files are backed up! Restart, and then press F8 before Windows loads. Look for the option of repair that may be on an advanced options menu. Follow the prompts. See if that solves network problems. And don't forget to visit the Windows Update site and reinstall all updates that are missing after the repair.

• Unable to connect via the Web client

  Dear team,

  Web customer service is installed on the SSO Server (SSO installed on seprate VM), since last year 1 it works very well, but as of today I m not able to connect through webclient get below error

  https://SSO.test.com:9443 / vsphere client / #.

  Unable to connect to the server vCenter Single Sign On https://SSO.test.COM:7444/ims/STSService? wsdl .

  Note: I am able to connect VC via vsphere client but not to Web client.

  concerning

  Mr. VMware

  After you restart the WebClient service, wait 5 minutes. Now, I m able to connect VC via the web client.

  Thanks for all the help and support.

• Laptop has virus and still unable to connect to the Web site after his withdrawal.

  Original title: laptop cannot connect to router

  my daughter portable computer had bankerfoxa virus I think that I got rid of but she still can't connect on the website I want to download microsoft security essential on his cell phone how if I can not connect? pls help

  Hi trinidadg,.

  Also try the following steps, you have a problem connecting to the Web sites.

  Try to do a System Restore to an earlier date when your computer was working well and try to run a scan for malware removal.

  Try to reset the Proxy settings to connect to the internet, as some malware enable proxy settings that block your ability to browse Internet sites.

  To reset the Proxy settings:

  Click Start-> in "search programs and files" type CMD-> in the programs in the list right click CMD and click 'run as administrator '.

  In the command prompt, type the following and press ENTER:

  NETSH WINHTTP RESET PROXY

  Restart the computer

  Touhami

• Unable to connect to the Web Client

  Hello

  It is impossible to connect to the Web Client. They receive the following error message:

  Error RSL # 29
  Error 2046

  We use vSphere 5.0 U3.
  

  Hello

  If please try kb article below and choose the right answer if it solves your problem.

  VMware KB: VSphere 5.0 Web Client does not load and displays the error message: Error # 2046 29 with RSL

  Thank you

  RAM

• Unable to connect to the Web site

  I can get www.calphalon.com to load but am unable to connect. When I created the account, calphalon did exactly the same thing ebay-t - it does not recognize the security code even if it is correct. I did exactly what I do on Ebay when I ask a question to a seller - I use Internet Explorer. You have created calphalon account no problem and am able to sign in and out of my account without any problem with IE, but when I switch back to FF (updated 22), this is a go. With FF, the sign of the popup box is much too small and is completely empty. When I go to the tab of the client service to register a product (this is why I am on the site), I filled up on the sign in info on the page and the kickoff, nothing happens. It's as if I never hit the Send button. It does not seem to convey anything at all. I have signed up for newsletters, but cannot access my account on ff so it seems I'm going w/IE when I get on this site.

  Hello

  Many issues of the site can be caused by corrupted cookies or cache. To try to solve these problems, the first step is to clear cookies and cache.
  Note: This will be you temporarily disconnect all sites, you're connected to.
  To clear the cache and cookies to do the following:

  1. Go to Firefox > history > clear recent history or (if no Firefox button is displayed) go to tools > clear recent history.
  2. Under "Time range to clear", select "all".
  3. Now, click the arrow next to details to toggle the active details list.
  4. In the list of details, see the Cache and Cookies and uncheck everything.
  5. Now click the clear now button.

  More information can be found in article to clear your cache, history, and other personal information in Firefox .

  This solve your problems? Please report to us!

  Thank you.

• Unable to connect to the Web site of 'report a problem '.

  I'm having a strange problem signing on the Web page 'Report a problem' in order to report a problem with an application that I downloaded via the iTunes store. I went to purchase in the iTunes store on my computer, click report a problem for the application in the order and he took me to a Web page called 'Report a problem' and asked me to connect.  However, I enter my information and click on connect, but the page just refreshes and doesn't connect. I know that my sign in information is correct (in addition to using it in iTunes, I just used to login here to post this question) and I came many times to just in case there was a typo in with my password.  I tried a longer password and it gave me the error "your AppleID or your password was entered incorrectly" so he is grateful to my info... I tried to clear cookies and cache from my browser (Chrome).  I also tried to use Internet Explorer and Edge to connect, but both had the same problem.  I couldn't even find a way to contact Apple on this specific problem... their support menus not occurred for problems of website that I could find at least (if someone could point me to that, I can try that as well).

  I had no problem connecting to https://reportaproblem.apple.com/ earlier. A temporary glitch perhaps?

  TT2