Unable to get the HP Solution Center to load. I uninstalled and installed printer three times.

Similar Questions

• Cannot get the HP Solution Center to load for officejet pro L7590 all-in-one printer

  Unable to get the HP Solution Center to load. Have an officejet pro L7590 all-in-one connected wireless (through the router) on my new computer Windows 8 but had to deceive it calling it a direct connection.

  I have a new computer with Windows 8.  I managed to get my HP officejet pro all-in-one L7590 printer connected and working with software downloaded from HP.  During installation it placed an icon on my desktop (the old format disktop I love) to the center of HP solutions, but when I try to open the Solution Center a message indicates that the installation is not complete.  When I try to install more software it brings back me to the orginal installation and indicates that the device is already installed.

  I want to clarify again once my choice of installation was directly connected even if it is wireless via a router.  It was the only way I could make it work.

  The Network Configuration page was just that you will find the IP address, but you have this.  It is not as important now.  Now that I've shown you a method to help you analyze let us begin the process is not easy to get the Solution Center works again.

  I was very happy to find an official document on your computer Windows 8 and the solution Center.  I think this should help you when you select your operating system on this page.  It is titled "The scanning device estintrouvable and other related errors" and will be a little better explain what you need to try to get the Solution Center to work once again, I am.

  Let me know if you have any questions concerning one of the steps here and I will do my best to answer those as quickly as possible. I do not know a few things to do if it does not, but it is certainly the best advice to try first.

• All-in - one Photosmart C8180: I'm unable to use the HP Solution Center to scan a document into the computer.

  I downloaded the updated driver that is located on the HP site for this printer. I uninstalled and installed this driver three times. I keep getting an error message when I use the HP Solution Center to scan a document to a PDF file. I restarted the program, rebooted the computer and reinstalled the software, as had been suggested in the error message.  I'm losing my patience! Anyone have any ideas as to the cause and the solution to this problem?

  Hi @AMDK,

  Thanks for getting back to me.

  This is a document of support that has alternatives for scanning when Windows 10 does not work with the software of the printer - Scanner without HP (Windows 10) software.

  If it helps you to find a solution, please click on the 'accept as Solution' and the 'thumbs up' buttons down below in this message.

• I have a PhotoSmart C 6180. I can't get the Software Solution Center

  Where can I find something that will download on Vista 64-bit for thePhotoSmart C6180?  My hard drive has been replaced and my backup did not include printer drivers.  I loaded everything and it prints well, but I can't scan as the center of Solution is missing.  It is said that if the printer is before 2011, the Center is not available and that the disc does not load on 64-bit.

  Y at - there a patch or something that can do this work

  Hello

  If you use the pritner via a USB connection, open the control panel and select printers, do a right click No matter which instance of the printer and delete it.

  Then unplug the USB and restart your PC before, installation of the printer. (For network connection simply go to the next step).

  Then download and install the following software through the screen, which will be added to all of the features as the HP Solution Center Software:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=MP-47461-2&cc=us&DLC=en&LC=en&OS=2100&product=1153494&sw_lang=

  Kind regards

  Shlomi

• I need to reinstal the HP Solution Center software on my PC and the office.

  I am running Windows Vista for a HP Phtosmart Premium All in One C309a. I deleted the application before a reinstall but this app (used to operate the printer) did not return. Everything works fine now, but I can't give orders to my printer/scanner. Impossible to find online a link to support or reinstall an attempt to update driver software. Can someone direct me to a link for the download?

  Hello cyberjack101

  What was your final decision?

  The reason why I suggested the link was that HP Solution Center should be in the full driver package.

  Always happy to hear that your printer is in working condition.

• Get the Error Message When you try to download and install Vista Service Pack 1

  Hello

  Update Windows guard neglect when you try to download and install Vista Service Pack 1 and I get the error message 80092004.  Please notify.

  Thank you
  Andy

  Hello

  Welcome to the windows vista forums.

  1. stop the Windows Update service (make sure that you are logged on as administrator)

  Click the Start button | Control Panel | System and Maintenance | Administration tools
  Double-click Services.
  (Provide the administrator password or a confirmation if prompted to do so.)
  Right-click the Windows Update service and click on stop.

  2. Click Start, type %windir%\System32 in the search box and press ENTER.

  Find and rename the folder C:\Windows\SoftwareDistribution.

  3. start the Windows Update service

  Start button | Control Panel | System and Maintenance | Administration tools
  Double-click Services.
  (Provide the administrator password or a confirmation if prompted to do so.)
  Right-click the Windows Update service and click Start.

  This procedure will erase your history on the Windows Update Site. Not important.

  Don't forget to restart and then try the update again. If there is no corruption in that
  folder, it would be gone now.

   

  Please, try now to windows update and check if you get the error.

  You can also download the stand-alone SP1 package. You can download the windows vista SP1 by clicking on the link below, please follow the instructions in method 3 in the KB article:

  http://support.Microsoft.com/kb/935791#Method3

  I hope this information is useful.

  Please let us know if you need further assistance.

  Concerning
  Rehman - Microsoft Support

• Get the 8004FF84 error when you try to download and install an upgrade for Windows

  I can't download and install an upgrade for windows. Try to install the product error code 8004FF84.

  Installation may stop if the system cannot copy files. Here are some possible causes and solutions for this problem:

  Your Windows installation disc is scratched, smudged, or dirty. Clean the disc with a soft cloth, insert it in the CD or DVD drive, and then start the Windows installation again. If your installation disc is damaged, you may need to replace it. For more information, go to how to replace lost, broken, or missing Microsoft software or hardware on the Microsoft Web site.

  Your CD-ROM or DVD drive is not working properly or the disk might be vibrating too much for the laser correctly read data. For more information about this problem, see your hardware documentation or contact the manufacturer of the CD or DVD drive.

  If your computer has multiple CD or DVD drives, your computer may attempt to locate files on the wrong drive. If your computer has a feature to disable CD or DVD drives that are not used, turn off readers that you don't use. Otherwise, try to insert the disc in a different drive, and then restart the installation.

  This is usually caused by hardware or software that is not compatible with Windows 7. If you have this problem, follow these steps:

  Wait about 10 minutes to see if the installation continues. Look at the led on the hard drive (often a small light on your computer that blinks when your hard drive is running) to see if there is no activity. If your hard drive seems to be working, the installation must be current. If your hard disk doesn't seem to work, go to step 2.

  Uninstall all antivirus software, and then restart your computer. Don't forget to enable antivirus software after you install Windows.

  If the installation fails again, it may be a hardware incompatibility problem. Go to the Windows 7 Upgrade Advisor on the Microsoft website to see if your computer can run Windows 7.

  If you have compatible hardware and your computer still stops responding, disable any unnecessary material. Remove (USB) universal serial bus devices. Remove or disable network cards, sound cards and cards of the series; and then restart the installation.

  If the computer still stops responding during Setup, contact your manufacturer computer or your retailer.

• New laptop Win7; When I try to start Firefox, I get the mess, "Firefox already running" error, I uninstalled and reinstalled with the same results.

  This started after I did some of my old computer Quickbook files windows easy transfer to my laptop. I uninstalled firefox and download the latest version on the site and still get this message. I don't see where it can be run. Thnx, Bill.

  This sounds like it is not the installation of Firefox itself that is messed up, but your profile folder (where are stored the your personal settings such as bookmarks, passwords, etc.). You say you used easy transfer, and that could hurt somehow.

  To start from scratch once again, follow the instructions under "create a new profile" here: https://support.mozilla.com/en-US/kb/Managing-profiles. I hope this helps!

• Cannot open the Web site nk.pl - already reset, uninstall and install new ff.

  After a virus (-serach.com, special box, search protect) changed my search on the site, I can't open a website nk.pl.
  Already done all that is described in the internet to get rid of virus, but still can't open a site.

  Separate the issue;
  Shows details of the system;

  Plug-ins installed

  Shockwave Flash 17.0 r0
  Shockwave Flash 11.8 r800

  Having multiple versions of a program can cause problems.

  Take uninstaller from here:
  Uninstall Flash Player | Windows
  Uninstall Flash Player | Mac
  Reinstall the latest version.

  Flash Player Version 17.0.0.134
  https://www.Adobe.com/products/flashplayer/distribution3.html

  https://support.Mozilla.org/en-us/KB/Firefox-cant-load-websites-other-browsers-can

• The HP Solution Center error message

  I want to use the scanner on all-in-one printer, HP Officejet 5610. I am running Windows 7 (64-bit).  When I select HP Solution Center it says that I'm not running the latest version of Adobe Flash Player for Internet Explorer.  It will not work until I update to the latest version. However, when I update I can't launch the videos sent to my email, so I was advised to uninstall and revert to a previous version.  How can I get the HP Solution Center to run without upgrading to the latest Adobe Flash Player. BTW, my favorite browser is Mozilla.

  I hate to say this, but you can't.  Center solution requires the latest version of Flash Player to run.  I don't know why HP has designed this way, but you need the it or any buttons.  I'm sorry.

• Could not load the HP Solution Center

  I had to reload my HP PC of the image of manufacturers, Windows update and upgrade to Windows 7.  I followed all the steps to load the full software features several times.  My impressions C4780, but the scan function has an error which suggests the scan from the PC.  Never loaded repeated loads and HP solutions Center does not get the responsible Solution Center.

  I hope not to repeat the full recovery.  Is it possible to get the PC based Centre of Solution without making the full restore?

  Welcome to the forums, @captbill99

  I understand that you're having trouble installing the software for the printer on your Windows 7 system, and can I just have a few suggestions to help out you!

  I suggest a level 3 uninstall first. This "deeper" uninstall will remove all the files on your PC printer.

  1. Click Start and type %temp% enforcement, press ENTER to open the temp folder

  2. Locate and open the folder starting with 7z (example: 7zS2356) (if there is more than one, choose the most recent folder)

  3 open the Util folder

  4 open the CCC folder

  5. run the L3uninstall.exe

  6. once the uninstall is complete, restart the computer

  7 run the Accessories\ System Tools Disk Cleanup

  8. download and install the latest version of Adobe flash player

  http://www.Adobe.com/support/flashplayer/downloads.html

  9 download drivers and full software features: HP Photosmart C4700 all-in-One Printer series Full Feature Software and Driver

  10. run the download to reinstall the printer

  I hope that does the trick and gets the installation completes successfully. If there are any problems during the process, save a screenshot or write me back with the details.

  Good luck

• HP Deskjet 4500 G510a Officejet - printer unplug the HP Solution Center screen

  Hello

  I have a HP Deskjet 4500 G510a Officejet and I am running Windows XP 7.  Just recently when I press print, a FACSIMILE screen from the HP Solution Center and I can not print from this screen either.  I set up the FAX Solution Center and it's works well but I don't know how to solve the problem that I am having with my printer.

  Any help would be greatly appreciated.  Thanks in advance.

  I'm sorry you have a problem with the printer and the solution Center.

  Try uninstalling and reinstalling the software and drivers.

  It seems that communication has become a problem between the computer and the printer.

  Let me know if it helps.

• tried everyting to sort the "assertion failed" in LightroomCC, uninstall and installed it again, tried to check the photo folder in the user account, it still does not, PLEASE HELP!

  Had "assertion failure" at the launch of LightroomCC, tried everything help, uninstall and installed it again, tried to check the photo in the user account folder, still does not, PLEASE HELP!

  Thanks for the help.

  My computer scientist has created a new user in my computer and now the 6 Lightroom

  works very well.

  Thank you

• Fix it fails Center with the error: unable to get the catalog of the troubleshooter. Error MatsGetSapCatalog failed

  Original title: Fix it center fails.

  Difficulty Center fails with the error:
  Unable to get the catalog of the troubleshooter. Error MatsGetSapCatalog failed
  I can't find the url of re - download.
  It doesn't seem to be at the Download Center.
  Thank you
  Frank C

  Vista Ultimate 64 bit sp2

  

  CF. http://answers.microsoft.com/en-us/protect/forum/mse-protect_scanning/scanning-engine-has-stopped-responding/e0f84bec-2555-4279-bfb7-aff691b8ba8d

• Please provide a place to get only the HP solution Center Program

  Aloha,

  My printer works fine on my network for a long time both wired and wireless.  I just deleted a desktower and upgraded to a new desktower.  Now, I need the Solution Center software.  It seems that I can't easily.  I don't want all the other bloatware that HP adds the installation CD, just the small software program for the HP Solution Center.

  Is this possible?

  Mahalo... Konadon

  Hello

  Just use the cd, then choose Advanced installation, you can choose the items that you want to install from a list.