Unique password on SAA for VPN access

Similar Questions

• Rule of NAT for vpn access... ?

  Hey, putting in place the vpn ssl via the client Anyconnect on a new ASA 5510, ASA ASDM 6.4.5 8.4.2.

  I am able to 'connect' through the anyconnect client, & I am assigned an ip address from the pool of vpn that I created, but I can't ping or you connect to internal servers.

  I think that I have configured the split tunneling ok following the guide below, I can browse the web nice & quickly while connected to the vpn but just can't find anything whatsoever on the internal network.

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080975e83.shtml

  I suspect her stockings for a nat rule, but I am a bit stuck if it should be a rule of nat object network or if it must be dynamic/static & if its between the external interface or external ip & network inside or the VPN (I created the pool on a different subnet), or a 'Beach' (but then I am getting overlapping ip errors when I try to create a rule for a range of IP addresses.

  Any advice appreciated,

  Hi Eunson,

  After have connected you to the ASA that clients receive an IP address, let's say 192.168.10.0/24 pool, the network behind the ASA is 192.168.20.0/24.

  On the SAA, you would need an NAT exemption for 192.168.20.0 to 192.168.10.0

  Create two groups of objects, for pool VPN and your itnernal LAN.

  object-group network object - 192.168.20.0

  object-network 192.168.20.0 255.255.255.0

  object-group network object - 192.168.10.0

  object-network 192.168.10.0 255.255.255.0

  NAT (inside, outside) 1 source static object - 192.168.20.0 object - 192.168.20.0 destination static object - 192.168.10.0 object - 192.168.10.0 non-proxy-arp-search to itinerary

  At the inside = interface behind which is your LOCAL lan

  Outside = the interface on which the Clients connect.

  If you can't still access then you can take the shot on the inside interface,

  create and acl

  access-list allowed test123 ip host x.x.x.x y.y.y.y host

  access-list allowed test123 ip host host x.x.x.x y.y.y.y

  interface test123 captures inside test123 access list

  view Cape test123

  It will show if the packages are extinguished inside the interface and if we see that the answers or not. If we have all the answers, this means that there might be a routing on the internal LAN problem as devices know may not be not to carry the traffic of 192.168.10.0 return to the ASA inside the interface.

  Or maybe it's that there is a firewall drop packets on your internal LAN.

  HTH

• password not required for internet access

  Hi all

  We use BBSM 5.3 Server to control our Wi - Fi access point in meeting for comments so that they can access the internet, but in a box, users can access the internet without any password. I don't have an idea on the BBSM server could please guide where should I look to fix the problem.

  Concerning

  Eliane

  Also, here is a link to the 5.3 SP1 guide http://www.cisco.com/en/US/docs/net_mgmt/cisco_building_broadband_service_manager/5.3_service_pack_1/configuration/guide/configsp.html.

  Lee

• ACL ASA5540 does not not for VPN access.

  I'm under code 8,03 and have a simple VPN L2L configured between two sites. It is in fact a test config in my lab, but I'm unable to restrict traffic using an ACL inside.

  I used the VPN Wizard to do the config initial and then added an Interior (out) ACL to restrict traffic once the tunnel rises.

  The encryption card is as follows:

  access extensive list ip 164.72.1.128 outside_1_cryptomap allow 255.255.255.240 host SunMed_pc

  Then I have an ACL to limit traffic to ping GHC_laptop, telnet to GHC_switch and denying the rest:

  inside_access_out list extended access allowed icmp host host SunMed_pc GHC_Laptop

  inside_access_out list extended access permit tcp host SunMed_pc host GHC_switch eq telnet

  inside_access_out deny ip extended access list a whole

  However SunMed_pc can also ping at GHC_switch and can FTP to GHC_laptop even if the 3rd entrance to deny any meter increases when I do this.

  I have attached a Word document that has the entire config with a screenshot showing the ACL and the shots.

  Should I configured incorrectly, or is ACL ACL actually does not work as expected?

  You can still keep all the IP for your acl interesting traffic. If you delete the sysopt, then you would write access in your acl 'inside_access' like you did above.

  If you are going to have dozens of tunnels l2l and will limit all, then I just remove the sysopt and use the acl interface.

  There is another option. You can leave the sysopt and use a vpn-filter. It is explained here and can be applied to l2l.

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a0080641a52.shtml

  http://www.Cisco.com/en/us/docs/security/ASA/asa80/command/reference/uz.html#wp1524559

• Limit bandwidth for VPN users

  Hi guys,.

  I use ASA Version 8.2 (1), I want to limit vpn users to use less bandwidth of my Interlink to access something on the inside of the network

  example: source vpn pool

  Destn: inside the network

  Please let me know how to achieve this with QOS config.

  Hello

  Probably the best would be to match groups of tunnel.

  class-map TG1-best-effort 

  match tunnel-group Tunnel-Group-1 

  match flow ip destination-address 

  Then this traffic in police policy-map and apply the service policy to the external interface (since you want to traffic police from your home). You can also use the pool for vpn access lists.

  For more details, please see:

  http://www.Cisco.com/en/us/docs/security/ASA/asa80/configuration/guide/QoS.html

• PC can see and access the laptop without asking for a user name and password but the laptop cannot access the PC because it asks me a username and password that I don't know.

  Vista - Windows 7 network connection. username and password is unknown.

  Hello

  I just got a laptop with windows 7 on it and I want to connect to my other PC for it, they are on the same network through a router. the PC can see and access the laptop without asking for a user name and password but the laptop cannot access the PC because it asks me a username and password that I don't know.

  If someone could answer this question, it would be great.

  Hello
  Maybe this can help.

  Win7 when configured on the peer-to-peer network has three types of configurations of sharing.

  Group residential network = only works between Win 7 computers. This type of configuration, it is very easy to entry level users to start sharing network.

  Working network = fundamentally similar to previous methods of sharing that allow you to control what, how and to whom the records would be shared with.
  
  Public share = network Public (as Internet Café) in order to reduce security risks.

  For the best newspaper of the results of each computer screen system and together all computers on a network of the same name, while each computer has its own unique name.

  http://www.ezlan.NET/Win7/net_name.jpg

  Make sure that the software firewall on each computer allows free local traffic. If you use 3rd party Firewall on, Vista/XP Firewall Native should be disabled, and the active firewall has adjusted to your network numbers IP on what is sometimes called the Zone of confidence (see part 3 firewall instructions

  General example, http://www.ezlan.net/faq.html#trusted
  Please note that some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible, configure the firewall correctly or completely uninstall to allow a clean flow of local network traffic. If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  ------------------------------

  If your network consists only of Win 7 and you want a simple network, use it.

  http://Windows.Microsoft.com/en-us/Windows7/help/videos/sharing-files-with-HomeGroup

  After you have configured the homegroup, scroll to the bottom for the Permission/security section.

  -----------------------------

  Win 7 networking with other version of Windows as a work network.

  In the center of the network, by clicking on the type of network opens the window to the right.

  Choose your network type. Note the check box at the bottom and check/uncheck depending on your needs.

  http://www.ezlan.NET/Win7/net_type.jpg

  Win 7 - http://windows.microsoft.com/en-us/windows7/Networking-home-computers-running-different-versions-of-Windows

  Win 7 network sharing folder specific work - http://www.onecomputerguy.com/windows7/windows7_sharing.htm

  Vista file and printer sharing - http://technet.microsoft.com/en-us/library/bb727037.aspx

  Windows XP file sharing - http://support.microsoft.com/default.aspx?scid=kb;en-us;304040
  Sharing printer XP - http://www.microsoft.com/windowsxp/using/networking/expert/honeycutt_july2.mspx

  Setting Windows native firewall for sharing XP - http://support.microsoft.com/kb/875357
  Windows XP Patch for sharing with Vista (no need for XP - SP3) - http://support.microsoft.com/kb/922120

  When you have finished the configuration of the system, it is recommended to restart everything the router and all computers involved.

  -------------

  If you have authorization and security problems, check the following settings.

  Point to a folder that wants to share do right click and choose Properties.

  In the properties

  Click on the Security tab shown in the bellows of the photo on the right) and verify that users and their permissions (see photo below Centre and left) are configured correctly. Then do the same for the authorization tab.

  This screen shot is to Win 7, Vista menus are similar.

  http://www.ezlan.NET/Win7/permission-security.jpg

  The Security Panel and the authorization Panel, you need to highlight each user/group and consider that the authorization controls are verified correctly.

  When everything is OK, restart the network (router and computer).

  * Note . The groups and users listed in the screen-shoot are just an example. Your list will focus on how your system is configured.

  * Note . There must be specific users. All means all users who already have an account now as users. This does not mean everyone who feel they would like to connect.

  ---------------------

  *** Note. Some of the processes described above are made sake not for Windows, but to compensate for different routers and how their firmware works and stores information about computers that are networked.

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Disable XAuth for remote access VPN

  Hi guys,.

  I would like to know if I can jump XAuth for access to remote VPN on a router.

  Here's my config, all working beautifully, always on connection I do not see any window username & password after having clicked on the Vpn profile.

  local VPNUSERSAUTH AAA authentication login
  local AAA VPNUSERS authorization network
  ra-user privilege 0 1cannotTELu secret user name
   
  crypto ISAKMP policy 7
  BA aes
  sha hash
  preshared authentication
  Group 2
   
  Configuration group customer crypto isakmp VPNUSERS
  theKEYallneedt0 key
  VPN-pool
  ACL ACL-SPLIT-VPN
   
  Crypto ipsec transform-set esp-3des esp-sha-hmac 3DES-SHA
  crypto dynamic-map VPNDYNMAP 1
  game of transformation-ESP-AES128-SHA
  market arriere-route
   
  list of authentication of card crypto map-OUTSIDE client VPNUSERSAUTH
  list of crypto card authorization card-OUTSIDE isakmp VPNUSERS
  client configuration address card crypto map-OUTSIDE meet
  card crypto 6500 map-OUTSIDE-isakmp ipsec dynamic VPNDYNMAP
   
  local IP VPN-POOL 10.1.24.1 pool 10.1.24.25
  IP extended ACL-SPLIT-VPN access list
  ip licensing 192.168.11.0 0.0.0.255 10.1.24.0 0.0.0.255
   
  Thank you very much!

  Hi Florin,

  In the case of remote VPN access, the user must be authenticated by name of user and password or certificates.
  You can deploy authentication certificate based as follows: -.
  http://www.Cisco.com/c/en/us/support/docs/security-VPN/IPSec-negotiation-IKE-protocols/22520-unityclient-iOS.html#router-config

  This will use the certificate for authentication of users and only requires name of user and password.

  Kind regards
  Dinesh Moudgil

  PS Please rate helpful messages.

• Windows asks for a password when you try to access to the "view work group computers."

  We are on a network.  Main computer, that we can access through the receptionist connect you and access shared files on this computer.  Computer from the receptionist, windows asks for a password when you try to access to the "view work group computers."  We tried to use its password.  However, the shared files are still not accessible.

  Hello

  1. what happens when you enter the password?

  2. how many computers are connected to this working group?

  Refer to this link and check: You cannot access shared files and folders or browse computers in the workgroup with Windows XP

  http://support.Microsoft.com/kb/318030

  I hope this helps!

• Manager Microsoft Access in the auditing keeps popping up for a password when I try to access any program - how to turn off this feature - where is it located?

  Manager Microsoft Access in the auditing keeps popping up for a password when I try to access any program - how to turn off this feature - where is it located?

  Hi Peggy Gore,.

  Welcome to Windows Vista answers Forums!

  Access Manager is a tool to control the types of content that your computer can access on the Internet. After Content Advisor activated, we can consider only rated content that meets or exceeds your criteria. You can adjust the settings according to your preferences.

  If you have set a password and you have forgotten your password, you may need to contact Microsoft Customer service to reset the password.

  For more information, please see the following links to Access Manager:

  Internet Explorer Content Advisor: Frequently asked questions.

  http://Windows.Microsoft.com/en-us/Windows-Vista/Internet-Explorer-Content-Advisor-frequently-asked-questions

  Using Content Advisor to block inappropriate web content.

  http://Windows.Microsoft.com/en-us/Windows-Vista/using-Content-Advisor-to-help-block-inappropriate-Web-content

  Hope this information is useful.

  Jeremy K

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• I forgot the password for VPN record how I opened

  First I have to buy the phone add password for VPN and I forgot how I fix this

  You can try to perform a repair of the system as it will be your phone factory reset or below, try to perform a factory reset, but in order to achieve a system repair

  Turn off your phone and unplug the PC (Hold to increase the volume and power for 10 seconds)
  Start PC Companion and select the area of support then updated my phone/Tablet then blue fix my phone/Tablet and follow the instructions on the screen - when you are prompted, always connect your phone off press and hold volume or back button - this should begin the process of repair or reformatting

  If you use Windows 8/8.1 or a 64-bit operating system and then adjust the settings for PC Companion and run in compatibility mode and choose Windows 7 or XP

• Cram session for the establishment of remote vpn access

  Our 'VPN guy' has recently left the company, and we demand to implement the remote access VPN 2 for two different customers very soon. I did a lot of lan connection database and things with cisco switches/routers, so I'm familiar w / cli, but I've never actually set up a virtual private network. I'm going to have to become a competent REALLY fast. Does anyone know of a good place for me to start (list of control/walkthru/whatever!) learn how to configure ipsec VPN for remote access? Of course, I did some research on cisco.com, but can't seem to find any guide "definitave" VPN remote access.

  A vpn will use a router in 1751, and the other will use a 831. In both cases we will use the cisco vpn client and radius authentication and authorization.

  I understand how VPNS work pretty well, but I am always a little scared...

  Take a look at this technology cisco.com guides.

  http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a00800946b7.shtml

  I used this as a base for my client connections.

• How to use ACS 5.2 to create a static ip address user for remote access VPN

  Hi all

  I have the problem. Please help me.

  Initially, I use ACS 4.2 to create the static ip address for VPN remote access user, it's easy, configuration simply to the user defined > address assignment IP Client > assign the static IP address, but when I use ACS 5.2 I don't ' t know how to do.

  I'm trying to add the IPv4 address attribute to the user to read "how to use 5.2 ACS", it says this:

  1Ajouter step to attribute a static IP address to the user attribute dictionary internal:

  Step 2select System Administration > Configuration > dictionaries > identity > internal users.

  Step 3click create.

  Static IP attribute by step 4Ajouter.

  5selectionnez users and identity of the stage stores > internal identity stores > users.

  6Click step create.

  Step 7Edit static IP attribute of the user.

  I just did, but this isn't a job. When I use EasyVPN client to connect to ASA 5520, user could the success of authentication but will not get the static IP I set up on internal users, so the tunnel put in place failed. I'm trying to configure a pool of IP on ASA for ACS users get the IP and customer EasyVPN allows you to connect with ASA, everything is OK, the user authenticates successed.but when I kill IP pool coufigurations and use the "add a static IP address to the user 'configurations, EzVPN are omitted.

  so, what should I do, if anyboby knows how to use ACS 5.2 to create a user for ip address static for remote access VPN, to say please.

  Wait for you answer, no question right or not, please answer, thank you.

  There are a few extra steps to ensure that the static address defined for the user is returned in the Access-Accept. See the instuctions in the two slides attached

• AnyConnect 3.0 supports IPSec VPN for remote access?

  Hello world

  I've read about Cisco AnyConnect 3.0 issues that it supports IPSec VPN for remote access:

  http://www.Cisco.com/en/us/prod/collateral/vpndevc/ps6032/ps6094/ps6120/qa_c67-622477_ns1049_Networking_Solutions_Q_and_A.html

  I downloaded and installed the Client AnyConnect Secure Mobility Client 3.0.0629, but I'm not able to get the IPSec VPN works. Also, it has no option to use the previous of Cisco IPSec VPN client PCF files.

  Can someone point me in the right direction to get IPSec VPN AnyConnect 3.0 work?

  Thank you in advance!

  Hello

  Takes AnyConnect support IPSEC from version 3.0, but only in combination with IKEv2.

  There is no option to use a CPF file with it and the config should be pushed through a profile Anyconnect.

  More information on this:

  http://www.Cisco.com/en/us/docs/security/vpn_client/AnyConnect/anyconnect30/Administration/Guide/ac02asaconfig.html#wp1325361

  You should also change the ASA config so that it accepts negotiations IKE v2:

  http://www.Cisco.com/en/us/docs/security/ASA/asa84/configuration/guide/vpn_ike.html#wp1144572

  Kind regards

  Nicolas

• ASA 5510 VPN for remote access clients are asked to authenticate on box

  Don't know what's the matter, but my remote access users are invited to join the ASA before connecting to the tunnel. How can I disable this? Config is attached. Thank you all -

  For remote access connections, you can turn off the prompt xauth (user/pass) with the following:

  Tunnel ipsec-attributes group

  ISAKMP ikev1-user authentication no

  -heather

• Failover of VPN client for remote access with the .pcf file

  Hi all

  It is possible to give 2 remote peer ip address to connect customer VPN cisco in FCP file, is possible to achieve failover.

  I have my firewall HO and DR configured for VPN remoteaccess. I need to specify two firewall ips in FCP file in PC client, incase HO firewall is not a customer VPN avialable will automatically connect to the firewall DR. I tried like below his does not work I think

  appreicaite any help...

  [main]

  Description =

  Host = 172.18.4.22

  Host = 172.18.4.10

  AuthType = 1

  GroupName = xxxxxx

  GroupPwd =

  enc_GroupPwd = DDBC400B7B3D1AEA1A5E6DEB5874CC057F759A6EED78B281F28D68F6A65380506D7E6CBA173B854C6ADC53FC49C1595B

  EnableISPConnect = 0

  ISPConnectType = 0 [main]
  Description =
  Host = 172.18.4.22
  Host = 172.18.4.10
  AuthType = 1
  GroupName = xxxxxx
  GroupPwd =
  enc_GroupPwd = DDBC400B7B3D1AEA1A5E6DEB5874CC057F759A6EED78B281F28D68F6A65380506D7E6CBA173B854C6ADC53FC49C1595B
  EnableISPConnect = 0
  ISPConnectType = 0

  Thanks in advance

  Mikael

  You must configure the server "backup":
  http://www.Cisco.com/en/us/docs/security/vpn_client/cisco_vpn_client/VPN...

  The easiest way is to do it with the GUI.

  Sent by Cisco Support technique iPad App