Unity connection Rehost license

Similar Questions

• Altered in Cisco Unity Connection and cancelled permits NTP server

  I use Cisco Unity Connection 8.6.1 and cancelled my Inbox licenses.  A few days ago I noticed that the timestamp of the voicemails was different from what said our CUCM so immediately, I assume that the NTP servers were different.  I was correct and made the change on our server CUC.  I came back to add another user, a few days later and was motivated that I didn't have enough licenses.  After researching on it after the fact, it seems that this happened because the value of NTP server is one of the values that cannot change with the current license, and I'm in a State of the trial for 30 days (24 days left now).  Now my problem is that I don't remember what would replace this NTP server.  How can I fix this problem?

  Hi William,.

  I guess the connection of the unit is installed on the virtual machine and therefore license MAC is here

  You can get the rehost license by launching the mail to [email protected] / * /

  regds,

  aamns

• Unity connection 8.6 Migration to 11 with CUCM 8.0

  Due to the right I'm going to intend a Migration of 8.6 connection unit to 11.0 of connection of the unit before I can improve CUCM. I am sure that the answer is Yes, but would there be problems running 11.0 of connection of the unit with CUCM 8.0.

  Nothing fancy on the face of connection of the unit, no unified messaging ect.

  New UC 11.0 should just registered the EPSC ports?

  Thank you

  Dan

  Looks like you need at least version 8.5 for the SCCP and SIP integration CUCM to be supported. Check the compatibility of connection of the unit guide below.

  http://www.Cisco.com/c/en/us/TD/docs/voice_ip_comm/connection/compatibil...

  Combinations for Cisco and unity connection Unified Communications Manager of the supported Version

  Table 22 Version combinations of supported for the connection of the unit and Cisco Unified Communications Manager

  Cisco Unity Connection	Cisco Unified Communications Manager
  8.5 and later	11.5 (1), 11.0 (1), 10.5 (2), 10.5 (1), 10.0 (1) 9.1 2, 9.1 (1), 9.0 (1), 8.6 (2), 8.6 (1), 8.5 (1)

  SIP: http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/connection/compatibil...

  -Terry

  Please note all useful posts

• How rehost licenses of one WLC2504 to another?

  Hi people,

  I can not rehost one 2504 at the other licenses. first of all, I can't find the button/link mentioned in configuration gude and secondly - when I try to use some similair, nothing happens.

  does anyone know where button\link of "look up a license under manage licenses" located exactly in the portal of licenses when rehosting licenses? I'm sure that the screenshots and instructions contained in the configurations of configuration guide. here what I see:

  screenshot_from_2015-12 - 29_185303.png

  

  Here, which is in the configuration guide:

  274708.jpg

  

  here what I try to do:

  screenshot_from_2015-12 - 29_185401.png

  

  then I insert WLC .lic file:

  screenshot_from_2015-12 - 29_185426.png

  

  and then I see this:

  screenshot_from_2015-12 - 29_185457.png

  

  by clicking on the 'next' button gives me a little short of 'treatment' window and then nothing. I'm not sure I do it correctly, but I tried.

  based on information from configuration guide I did support I can rehost licenses myself. is this always true?

  I have not tried on a 2504, but it worked on a 5508.  All I can say is call TAC and make them rehost license.

  -Scott

  Evaluate the useful ticket *.

• AnyConnect Premium - Rehost license

  Hello

  I´d would like to know how the license Premium Anyconnect rehost. Is this possible?

  I mean, I have 10 license on my ASA and now I´d to put it on an other ASA.

  How to do this?

  Kind regards.

  Sorry but what you ask is available in the case of a number of RMA (Return Material Authorization) of a failed unit. The reasoning is that the old unit will not 'license' for what is already.

  If you are the old unit and rating upgrade - tell to a 5500 to 5500 - Series X - you may be able to get your manager to bring some relief from cost under the technology transfer program, but which differs from the rehosting license.

• Unity connection 7.1 email notification of voicemail

  I'm running the unit connection v7.1 and trying to provide my users with the following solution:

  (1) they get notified by e-mail when they receive a voice message.

  (2) the email contains information about the phone number and name (if it is available through AD) of who called.

  (3) they have a method to listen to the voicemail of their email.

  (4) the email cannot contain a voicemail .wav file, or have another method for a user to record voice messages in the form of .wav file.

  (5) ideally, the email will contain a link which broadcasts voice messages, or who takes the user directly to their voicemail box Cisco Unity Connection.

  I was able to successfully get the system to send a notification email with the phone number & name (as appropriate via AD).

  I was able to get the system to include a link in the email, but the link directs the user to the personal Communication Assistant homepage where the user needs to log, and then click the appropriate link to access their Inbox.  Is there a way to circumvent the obligation for the user to log on and also to send them a link directly to their voicemail box?

  If not, is it possible to configure the system to send a link that could listen to the specific message to a particular email notified their?

  I am open to the 3rd party add-ons for the solution.

  The only solution I can think is to build a solution in which the email is sent to an application of custom software that interacts with the Cisco equipment & sends the e-mail to the end-user.  It's not ideal.

  Thanks for the thoughts you can provide!

  Develop my comment.  I think that there is a major holdup is that:

  "(5) ideally, the email will contain a link which broadcasts voice messages, or who takes the user directly to their voicemail Cisco Unity Connection Inbox...

  Is there a way to circumvent the obligation for the user to log on and also to send them a link directly to their voicemail box? »

  SSO (single sign - on) is a problem because there may be several areas, you want this to apply to: for example, are you talking about SMTP to only internal, company email address?  You want to extend this to an external address?

  Technically, there is the IMAP (integrated messaging) solution which offers the possibility to get voicemail into email but, again-, this conflict without obligation your attachment or WAV.  You could go with secure messaging, which always has a WAV attachment, but the user must be authenticated to do anything with the message.

  You may be able to find something to your liking, but I doubt it will meet all of your initial needs.

  Hailey

• Difference between Csico and Cisco Unity Connection unit

  What are the main differences between Cisco Unity and Cisco Unity Connection (version 7)

  as: 1. in Cisco Unity servers are active - failover Mode and about unity, the servers are in active-active mode

  2 Cisco Unity, knows about unity and unified messaging, integrated messaging

  What is the major difference between Unified Messaging and integrated messaging?

  Please provide some points of difference between the two...

  This may well be true today, but the gap could soon close... otherwise disappear.  Cisco is currently in EFT (field-tested at the beginning) or testing "beta" for the connection of the Unit 8.5 (1), which aims to add features of Unified Messaging Unit connection using WebDav for Exchange 2003 and Exchange Web Services (EWS) for Exchange 2007/2010.  Just a nugget to think when you consider the timing of your client to install and what platform would be best suited to most environments.  Take a look at this blog for more information/thoughts:

  http://www.netcraftsmen.NET/resources/blogs/unity-connection-with-Unified-Messaging-where-will-unity-fit-in.html?blogger=David+Hailey

  Hailey

  Please note the useful messages!

• Cisco Unity Connection deployment

  IM deploy CISCO 1.X for one site unit connection. The partition & call search are created on 4.1 CM. Both phones are added to this partition on the call manager for a local test (telephone2 telephone1 - to-).

  On Voice Profile fighter pilot number is 2010 and the DN of departure for the voice port is 3000. I have configured the phone 1 extension (2015) and telephone 2 (2011) on the Cisco Unity connection.

  when im 2010 (pilot number) im getting the busy tone or the phones calling each other it keep humming without leaving numbering MWI

  You can feed me for cisco unity connecton single site deployment.

  Kind regards

  What are the numbers that you actually assigned to the ports of voicemail? Have you created a list of hunting that indicates the number of driver? Go to the port of voicemail list and try to call one of the ports directly? Unity connection answers?

• Speech and cisco Unity Connection connect

  Hi all, I've read that speech Connect is available for Cisco Unity Connection Version 7.1.3 and later versions. I installed CUC7.1.3 and CUCM 7.1.3 and I would like to configure this feature.

  If someone have this plase share tips or a document.

  Thank you very much

  David

  Speech Connect is actually integrated in the application of the CUC.  There really isn't any special rig or something like you would have with speech Connect for the unit. When you choose ' enable voice ' Manager directory or AA and you search by name, which is essentially the engine speech connect to work. "  If the user has a registered name, you will hear him play.  If this isn't the case, YOUSSOUF (AutoAttendant activated by speech) will deliver the names for you.

  Hailey

• Unity connection 8.5 Accessing and purge messages from the user as administrator

  Is it possible that an admin I can purge a registered users of voice messages in Unity Connection 8.5 without deleting their account in full and recreate?

  Is it also possible using an admin account, I can access a users mailbox and export messages to individual files (.wav, etc.) for purposes of storage/reading/evidence?

  Jim

  Hi Jim,.

  Just as an info... .the unity tools are not 3rd party, but rather built and

  support of the Cisco BU's messaging products. My

  Guess is that most, if not all are designed/built by Mr. Lindborg itself

  and that's probably why they are so important to use. I used this tool a lot

  both ends different many without problem

  I can't imagine the unit running connection without using this large suite

  Tools.

  http://www.ciscounitytools.com/sitelist/AllDownloads/AllDownloads.html

  In regard to the messages, you can use Web Inbox and

  registration as a Save option to save messages in the form of .wav files.

  See you soon!

  Rob

  "Celebration is around us, every nations, all around us.
  "Singin' ' forever young, sing songs in the Sun '-K'naan

• Rehost licenses of ELM of connection of the unit to the server CUCM PLM

  Hi all

  I just finished a CUCM migration / MCS 8.0.3 upgrade to UCS 10.5.1 using PCD. I will now upgrade my 9.1.2 Server stand-alone connection of the unit to the 10.5.1 version tomorrow night. My question is about licensing. When I upgraded version 9.1.2 connection unit I decided to re co ELM since my CUCM cluster was still on version 8.0. Now that I have improved my CUCM cluster, I have two license servers - PLM for Call Manager and ELM for the connection of the unit. I was advised to move the licenses of connection of the unit to PLM, but I don't know how to do it. I have already contacted Cisco licenses and they tell me that everything is ready to go, but they have not told me HOW to do it (I know they are probably deluged with requests).

  Can someone point me to a link or describe briefly the process please?

  Thanks in advance!

  Lisa

  You probably didn't clearly explain what you wanted to do, he will be re - host licenses of a PLM to one another as before PLM with the MAC addresses of license.

• rehost licenses

  We have now four 5508 who have node Lock licenses and we want to replace all 4 WLC drank new wlc 5520 who RTU licenses.  is it possible to make the rehost or we need to purchase new licenses? Concerning

  5508 to 5520?

  Yes.

• Will be CUCM 8.6 continue to work between the change of license MAC and download rehosted license?

  Hi all

  I'll change a sensitive parameter of CUCM 8.6 and that will trigger a recalculation of the MAC license. Now, I would like to know if anyone knows weather and all has how long will continue to work until I have download the new license rehosted. Thanks in advance.

  You have a grace period of 30 days to download the new license when you do this.

  HTH

  Java

  If it helps, please note

  www.Cisco.com/go/pdihelpdesk

• Rehost license of 6140 to 6296

  Can I use the tool to transfer license of Cisco to rehost 6140 licenses to 6296 s new? Customer buys 6296 s new to replace their 6140 s which are fully licensed. Can we use the license transfer tool that is available to the www.cisco.com/go/license to transfer port licenses?

  Jeremy,

  I confirmed that the licenses are not transferable.  The only time allow us the transfer is a replacement (RMA).  Platforms, you will need to purchase new licenses, unfortunately...

  Kind regards

  Robert

• CUCM Rehost license

  Hello all, I searched this topic but have not yet found, if I appreciate all the help. Here's the rundown:

  I changed the NTP server to my CUCM (he has been "spamming" of the error log). I have not implemented the system and didn't license VMWare was like that, then of course, my license is entered 30-day grace mode. I got a license file sent to me, but when I try to download, it tells me it's the same license file that we already have and I can't set it up. What Miss me? I'm talking back with the license person who gave me the license, but I hope that I didn't ask for the wrong thing. Any help would be appreciated, I wasn't the first person who would take care of this system, but now it is on my lap! I intend to use this experience to work on obtaining certificates, but I'm still a beginner.

  Thank you!

  Hello

  Just to add a note to the good advice of friends Terry & Aman (+ 5 each!)

  As noted Terry passes along this Bug ID to the TAC engineer (note the number of Support requests = 210);

  CLI file delete license does not remove DB entered licenseinfo
  CSCtc59039

  Symptom:
  Entries in the DB are not deleted after removing the license file via the cli command
  deleting file license

  Conditions:
  This problem occurs when there is only a license file uploaded to the server
  and the user removes the license file

  Workaround solution:
  user must delete the corresponding entries of the DB in the licenseinfo table.
  To do this, TAC should be contacted (e).

  Notice the CUT also will document this issue and declare the CUP does not support valid
  withdrawal of licence through the CLI command. The only time the user must
  delete the license file is that a Publisher rehost is executed and the original
  license file becomes invalid. users must download a new license file,
  Use this cli command to remove the invalid license file, and then restart the license
  Manager.

  Other Description of the problem:
  This problem was introduced in Version 8.5 only. Older versions are not affected by this bug. For all versions License Manager must be restarted after any changes to the system files for the update database.

  Last modification:

  Feb 25,2015