Unrecoverable DV7 after BSOD

Similar Questions

• Satellite C870-12F - problems after BSOD

  Hello

  Well 15 minutes ago, I worked very well with my laptop computer and all of a sudden, I get the bsod... ?

  Then it restarts and after waiting 5 minutes for the windows screen to disappear to a welcome screen, it does not appear... So I tried the recovery.

  NA not work it gave me an error... While writing on this subject all of a sudden he started through the office...

  How is that even possible...

  There are two possible reasons why BSODS happen.

  (1) serious software problem
  (2) hardware problem / fault

  In the case of point 1) system recovery / laptop should solve this problem. But it doesn't have t
  So, I think that, in your case, the material started to malfunction.

  You want to know what part might not work.
  Well, I think that these details can be provided only by an engineer who has already checked the aircraft and ran some diagnostic software.

  In my opinion its HARD drive problem isn't. If something's HARD drive, unit turns on properly but would not boot the system.
  Possible hardware parts that could be affected are: module of RAM or the motherboard.

  RAM problems can be solved easily in replacement of the module, but for motherboard problems, the fix for laptop can be very expensive in case the warranty isn't valid.

• 810-160 Phoenix envy: envy phoenix 810-160: try to install Win10 after BSOD and format; drivers not found

  A few weeks ago, I got the BSOD and could only reformat without saving. After a data recovery service ravaged my hard drive, I bought a new drive. My recovery disk is not found (my guess is the woman she pitched in one of his fits of cleaning). Of course, I have to re - install the operating system and bought Win10 home.

  I plugged the USB and started the installation, but now get a message that no driver device were found. It is a pain, but it makes sense. Went to the website of HP drivers on your laptop and downloaded all the drivers, it produces for my specific model.

  Where I'm stuck:

  I have a pop up that says "Windows Setup" and "Select the driver to install", with a window not populated. I plugged my USB key containing the drivers and found him - USB key (H.) I chose this drive and the folder where I placed the drivers. Click OK and I get the message "no device driver has been found. Make sure that the installation media contains the correct drivers, and then click OK. »

  If I have the drivers provided by HP and they are not recognized, how do I proceed?

  Hello:

  Make sure that you dΘmarrez from a USB 2 port.

  You will not be able to install Windows from a port USB3.

  If you have the W10 installation media in a USB 2 port, windows can you are looking for the sata controller driver, so see if it works...

  Download the drivers from this link below (first or second listed file - 1 file listed (64-bit).

  https://Downloadcenter.Intel.com/download/25165/Intel-rapid-storage-technology-Intel-RST-RAID-driver

  Extract (copy) the files on a USB FlashDrive without all records.

  With the flash player and the installation media W10 plugged into the machine, boot from the W10 installation media.

  After selecting the install now option, select the training - Advanced menu, Options and select the option load a driver.

  You should now see the storage driver files listed.

  If you check the box, it only includes the compatible driver.

  Follow the prompts and I hope, W10 will install.

• Satellite A200 PSAE6E lights after BSOD

  Hello. (Sorry for my English)

  Last night I had the BSOD (driver_IRQ_NOT_LESS_OR_EQUAL). After memory dump that I restart laptop, but it doesn't.
  Starting the fan for 1-2 seconds, I hear some noise from the DVD player, led to power is blue, same as witness to power, seeing the battery cord is dark when the laptop is disconnected from the AC.

  Hello

  My laptop crashed and could not start because of problems with RAM.
  My modules of memory are dead for no apparent reason

  In my opinion the RAM modules need to be checked.
  Remove one and check both in each slot
  But it would be better to use the new modules.

  However, if the problem is not related to modules of RAM then it must be a serious problem of material possibly a motherboard or something like that

• How to disable automatic reboot after BSOD XPSP3.

  It continues to, and I need to know how an automatic restart not after it BSOD, I can see this error message I receive.

  Preference does not change the registry, thank you.

  Make a right click my computer and select Properties. Click on the Advanced tab click settings under Startup and recovery. Under system failure, uncheck 'automatically restart '. Click OK.

• Windows 7 unrecoverable system after installation of ArcGIS - KB973688 and KB954430 errors

  Hello!

  I am running Windows 7 ultimate x 32 and windows update will not install two updates after installing ArcGIS 9.2:
  -Update for MSXML Core services 4.0 Service Pack 2 (KB973688)
  -Update for MSXML Core services 4.0 Service Pack 2 (KB954430)

  I tried several times with retry and installation manual several times with and without boot and startup (disabled UAC; admin install...). No question.

  I get to kb973688 errors:
  -Error code 643 (try it with windows update)
  -HRESULT: 0x800736FD (installation manual try, it stops at 2/3 progress bar, saying "Publishing product information").

  WindowsUpdate.log said several times:
  -WARNING: Failed to evaluate installed rule, updateID is {...}
  -WARNING: Failed to evaluate installed rule, updateID is {...}

  Between the parentheses, there are different channels such as D8BD0CF7-C4A8-48A8-9B1F-E791CE07F934.

  I tried to uninstall the updates with Add/Remove windows components, but no components are presented.

  CrapCleaner (ccleaner) tool shows, however, that there is a system restore point at a time where KB973688 was supposed to be installed.

  Finally, I tried the system restore to a couple of restore points, but restoration said that he cannot restore (!).

  So my last try: clean install from Windows 7, Windows XP Mode, installed ArcGIS 9.2 v. in Win XP Mode and I was back again smooth and clean.

  My question is: how is it possible that any application can corrupt and Win 7 so much! We hope enough that I got the chance to start, but if not, how can I recover my system and I want to say my system restore points and my options to add or remove system components?

  Have a happy new year!

  I found the following solution on the ESRI website that has worked for me.  It is a minor registry fix which gives more storage space for the Windows registry:

  http://forums.ESRI.com/thread.asp?c=93&f=1148&t=287391#902480
  Update MS in question above installed as soon as this fix has been applied.
  Good luck!

• Cannot reboot after BSOD

  I tried to install a USB wireless to make my laptop Wifi capable.  Now, I can't restart xp or go to the last known configuration or get anywhere after all the guests on-srceen.  If I could start and to get online, I would probably update all drivers.  Any suggestions to get there?  I don't have a disk to reboot.

  Try this forum instead: http://answers.microsoft.com/en-us/windows/forum/windows_xp-system

• Microsoft, black expensive after BSOD screen.

  my mobile Samsung r518 was a BSOD, I clicked on panic directly on power off, later when I tried to start it up, it closed it itself, also when I try to start t now it will start but it does not start any system upward, it's a rear screen with only turning im desperate, pls help! You can't lick on any tabkeys since it will be helpless, I also tried evrything, f12, restarted as 100 xtimes literally.

  Hello

  Your question does contain all the required information necessary for us to help you. Please provide us with the following information.

  1. What is the error message?

  Try the following methods to resolve the problem:

  Method 1:

  a. try to start the computer in safe mode. Refer to the city link below to start the computer in safe mode:

  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

  b. if the problem does not occur in safe mode, perform a clean boot in order to find the problem causing the element. Follow the steps mentioned in the link to perform the clean boot:

  http://support.Microsoft.com/kb/929135

  Method 2:

  a. you can also try mode low resolution:

  http://Windows.Microsoft.com/en-us/Windows-Vista/advanced-startup-options-including-safe-mode

• HP f4480 has worked with dv6 but not with the new dv7 after transfer windows easy

  F4480 will not be printed with the new laptop dv7, I can scan to laptop and the printer works with the old dv6 but it will not print and shows no errors. Print jobs just disappear.

  Have reinstalled several times with the removal of the pilot tool and all the info on this site.

  Me using fixed http://support.hp.com/us-en/document/c02554863 of HP diagnostic tools

  A rather well hidden resource.

• Lost beats audio visual Volume indicator on Pavilion dv7 after the bios update.

  HP ran an update of the bios.  Beats audio indicator volume of volume segmented system stopped showing.  When the volume function keys are pressed upward or to the low volume going upwards or downwards, but the Visual indicator has disappeared.  I am partially deaf then when I hear it without headphones everyone in the House he knows also.  Tech to reset the system to the old bios and still no Visual volume control.  It is important for me and somebody tell him to run a recovery and lost information is not an option.

  Hello

  Download and reinstall the HP OSD utility at the following link.

  http://ftp.HP.com/pub/SoftPaq/sp55001-55500/sp55152.exe

  When this has completed, restart the laptop.

  Kind regards

  DP - K

• BSOD on install of Windows 7 after hard drive crash

  I have a HP Dv7 with Intel i7 and 8 GB memory. About 3 years.

  Recently, I lost my hard drive to a physical failure. I bought a 120 GB SSD as the principal and a 1 TB drive 7200 RPM as the secondary to be replaced. I ordered the HP restore kit to reinstall Windows 7, but each installation stops at "loading drivers" step and gives me a BSOD. I tried to remove the SSD drive and using only the hard drive, but the same results. Also tried to do a clean install of Windows 7 with an ISO image to a bootable USB key. The same problem. I also tried swapping the primary/secondary locations for readers.

  Nothing I have tried seems to work. I'm desperate for a solution! Why would I get a BSOD on a reinstallation of the software factory?

  I am trying install Windows 7 without SP1 to see if that works, but have no chance. What else can I try? What I have to install Windows 8 to work with the new hard drive or SSD? »

  I tried to restore 4 times (3 hours + per attempt). I tried the clean install of Windows 7 SP1 at least 10 times, each of them do not reach the exact spot. Windows won't INSTALL, so that steps can be taken?

  As I posted earlier, I had problems with installing Windows 7 on my laptop HP Pavilion Dv7 after replacing a hard drive defective. I ordered the kit of training materials ($60) and the operating system of restoration kit (essentially Windows 7 and drivers) on a 4 disc set. I paid the extra money for all accelerated for me.

  After you have installed a 120 GB SSD and the new 1 TB drive 7200 RPM, I tried to install the operating system using the DVD restore I ordered. Each installation took about 4 hours and each of the 3 times (i.e. 12 hours!) installation has failed at the end of the installation process. Then I downloaded a clean version of Windows 7 ISO and burned a bootable USB an attempt installs another 15, which also failed at the end of the installation process.

  In desperation, I contacted HP support and was informed that I had to pay for technical support. I must say that I was really disappointed by HP and HP «each incident» support I spent $59 and 3 hours talk with some idiots in the new Delhli, who accompanied me through a few tests of BIOS of base no matter what 3-year-old could have understood, I sent them a picture of the BSOD and error code, and they arrived at their 'solution' to send me my laptop to HP for them to install a new hard drive and reinstall the operating system for the pittance of $200 and 7 to 9 days!

  I refused their generous offer to relieve myself of the burden of $ 200 in my wallet and took the laptop to Fry when I bought it. After 15 minutes of discussion about my question, the tech told me that I needed to install the Intel drivers during the installation of Windows 7. He popped a USB key containing the Intel drivers, I've needed, continued with the installation of Windows 7, and I was back at home with a working machine within the hour. It cost me $35. A BARGAIN, given that HP, the company that BUILT my laptop was completely distraught about this problem and the only solution was to deprive me of my laptop for 9 days and during this time, charge me $200.

  So to all who read this, please pay NOT for the HP "per incident" support. They are slightly educated idiots who know no more about the HP product than your typical 3 yr old child. For example, they suggested that the HP laptop in my possession was "very sensitive" and I wouldn't be able to put 'any hard disk that was not exactly to the same specification as that was in it from the factory'.  Idiots.

  I you need to re - install Windows 7 on your laptop, visit the Intel website and download "floppy" (i.e. not the executable versions which self install) versions of their drivers for your laptop, load on a USB stick and when begins the installation of Windows 7 where it asks if you want to load the drivers, select the drivers on your USB key and installation will be smooth.

  Again, how is it possible that HP and their support forums are not aware of the problem or the solution? Seriously. This is probably the last HP I buy. Just exhausting and annoying to deal with this.

  Craig

  PS - My HP Pavillion DV7 is smoking quickly with the new solid-state drive and updated 7200 RPM secondary drive. * beep * thing boots like 20 seconds and Photoshop load almost INSTANTLY. Incredible.

• Pavilion a1647c bsod after sp3 install

  Hi, system of maintains reboot after bsod just installed sp3 and renamed intelppm.sys. now, I can't even on safe mode or recovery console. tried to boot the xp disc and on the repair system, it will not show the partition c. help

  Tom

  Try to move the HARD disk to another system and rename the file, and then bring it back to your system, but try to start safe mode

• 3270nr HP Envy, random BSOD

  I bought it a few months ago the beginning of the year, it worked great, was able to leave it on for a few days with no problems at all, but this week he started getting random BSOD, I did a test of stress with the CPU, was 100% usage for 20 minutes or so, do not go beyond 80 degrees (Celsius) and has not either the BSOD at first I thought it was steam associated, but this morning I left it on just to charge my phone with nothing open and he got a BSOD I think, because it shows the same image sometimes watch after BSOD, saying: there is no OS installed, I did not format after purchase, or made changes on the hardware all I use is a USB mouse. The attachment is the image which shows sometimes after the BSOD, but other times he just asking if I want to start Windows normally, with the network, or safe mode. It works very well after that I have press and hold the power button to force it to stop and restart. At the hope of solving this problem here before trying to exchange it for another or something.

  Hello

  If the hard drive test failed there is a hard drive problem and must be replaced. If your laptop is still under warranty, then you can call the HP technical support to get it replaced.

  HP Notebook PC - test a hard drive by using the Built in Self Test c00439024

• HP Pavilion g4 2131tx, hard disk after Blue Screen of Death error

  Hello! I do not know what section shoud I post this problem, I apologize for that.

  If my phone is freezing for days after BSOD. When I leave my laptop at night to download torrents, I always get the message "Windows has recovered from stop unexpected." when I woke up.

  I already disabled all non microsoft services, startup items and yet the office is always freezing just after the Welcome screen, but the Welcome screen does not load too long.

  The freezing of funds of more than one minute, and then it will return to normal again until my laptop went to BSOD
  and received this error of UEFI "Disk hard error" after restart.

  I ran the Diagnostic Test of equipment and got the result:

  Failure ID: RW042K-6MT6RP-MFPX1F-61BK03
  Product ID: 65H69PA #UUF

  I tried registry cleanup and defragment the disk and still no luck.

  * My laptop is HP Pavilion 2131tx g4 and still under warranty until June 2014.
  * I use Windows 7 Ultimate 64-bit Service Pack 1
  * My RAM is 4 GB with an Intel Core i7 processor
  * My AV is microsoft security essentials
  * I use Advanced SystemCare for registry cleaning and Defrag.

  I was wondering if I could change my drive hard while it is still under warranty.

  Thanks for your help!

  #Edit: bad English >.

  Here is the Service Manual:

  Manual

  See Page 39. It can take any 2.5 inch wide 9mm thick laptop SATA hard drive. They are the industry standard, interchangeable.

  Here's one that I would recommend:

  http://www.Newegg.com/product/product.aspx?item=9SIA2W00YW3532

  It is a compromise that is friendly with size, speed and spending. You could install an SSD for maximum speed. Post back if you need help with the software or anything else.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Why all the BSOD? More in the last 10 days than the last 10 months

  All of a sudden in the last 10 days, my PC has been constantly stop, a few automatic reboots [I know because Google Chrome, Opera & Internet Explorer all ask what I want to open the pages who suddenly disappeared]. Others showing the BSOD of different color...

  Sometimes I got BSOD too, although on these occasions, it was not the old blue screen dark with a myriad of writing, instead a lighter blue screen telling me to stop, the evidence gathered [to up to 100% and then auto shut off and reboot]' the last 3 times there have been various error messages invited me to do a search on the internet for the answer...

  IRQL_NOT_LESS_OR_EQUAL

  DRIVER_POWER_STATE_FAILURE

  KERNEL_DATA_INPAGE_ERROR

  I did a bit of googling, found at Microsoft support group where others have been invited to copy, the minidump zip files and upload to skydrive; what I've done; the zipped file is available for reading... but do not have done this before. I'm not sure of the next step... I tried to simply enter answers.microsoft.com in the municipality filed, but it was not acceptable...

  If I had to guess, in the previous six months before the current problems, I doubt that there are 2 episodes of BSOD stop.

  I am running windows 8.1 completely up to date and it's really p * sing me OFF... others may say their system starts up quickly, and I confess that I have 3 or 4 drives external storage, and I use Acronis as a safeguard measure after the last time I had to reload Windows [due to a failed update]... but after BSOD today... I timed it the beginning upward and it took 1 min 45 sec as soon as the start screen first showed... when the blocked password login screen appeared... so I want this issue fixed! PLEASE...

  Chris

  There are 3 different causes, but according to me, there is an underlying problem.  Please run the Driver Verifier to find which driver he is

  These accidents were related to the corruption of memory (probably caused by a driver).

  Run these two tests to check your memory and find which driver is causing the problem.  Launch auditor.  You don't need to run memtest again unless the auditor is not the cause, or you want to.

  If you are overclocking anything reset by default before running these tests.
  In other words STOP! If you don't know what it means that you're probably not  
  
  
  
  
  1-Driver Verifier (for full instructions, see our wiki here)
  
  2-Memtest. (You can learn more about running memtest here)