Update IOS Cisco Aironet 1200 series

Similar Questions

• Point of access Cisco Aironet 1200 series help

  We have 4 Cisco Aironet 1200 Access Points and they are all set to authenticate with our RADIUS server. However, authentication is hooked and can't understand why. Does anyone have any knowledge/experience with Cisco Aironet 1200 Access Points configuration?

  OK, I do not work with the GUI so although the memory is a little hazy but from the APs home page look on the left hand side and there is an option for something like "Software Setup" or something to that effect. You should be able to find the IOS version of here. This requires that you are indeed runnig IOS code. How old are these APs? If more than a few years ago (and perhaps even more recent) that they could very well be running VxWorks and then we are in a different ball game. If you see what I have described above and the homepage for the AP is often white with a bit of greenish-blue, bluish-green color then IOS, if it is more colorful, yellow stuff and VxWOrks.

  I hope this helps. Let me know if you need anything that anyone else. I will try to answer as soon as POSSIBLE.

• Only the needs of the Cisco Aironet 1550 series a WLC?

  Hello

  Nice day.  I would like to ask if the Cisco Aironet 1550 series requires a controller to run.  Note that the references SKU in this fomat AIR-CAP1552E-A-K9-AIR-CAP1552EU-A-K9.  I noticed that on the autonomous access point there they keyword 'SAP' on its SKU while the controller based has "CAP".  If the

  Cisco Aironet 1550 Series needs a controller which controller should it be associated? (e.g. AIR-CT2500)

  Thank you

  It can work stand-alone image:

  http://www.Cisco.com/en/us/partner/docs/wireless/access_point/iOS/release/notes/15.2_2_JB.html#wp355908

  1550 relies on:

  2500, 7500, 5508, WISM2,... .etc

  check the release notes of the code controller that you have and you should be able to identify what is supported and what is not supported.

  ----------------------------------------------------------------------------------------------

  Please ensure good answers to rate

• Cisco Aironet 2600 series Configuration of the DHCP server is NOT serving addresses?

  Cisco Aironet 2600 series Configuration of the DHCP server is NOT serving addresses?

  I have (2) AIR-SAP2602I-A-K9, configured the same way.

  on two different remote LANs.

  They don't seem to be handing out addresses via DHCP.

  {If I connect to a local network with another DHCP server}

  wireless devices can obtain addresses

  This another DHCP server on the LAN through the access point.}

  I followed 12.4.25d. JA.cg.pdf

  Configuration of the Access Point to provide the Service DHCP 5-22

  ---------|---------|---------|

  e.g. 3444-RCS1-AN #show running-config

  Building configuration...

  version 15.2

  3444-RCS1-YEAR host name

  no ip Routing

  USH - DM IP domain name

  DHCP excluded-address IP 192.168.29.89

  IP dhcp RCS1 pool

  network 192.168.29.88 255.255.255.248

  router by default - 192.168.28.1

  Rental 1 0

  interface BVI1

  IP 192.168.28.211 255.255.254.0

  no ip route cache

  default IP gateway - 192.168.28.1

  ---------|---------|---------|

  ---------|---------|---------|

  e.g. 3444-RCS2-AN #show running-config

  Building configuration...

  version 15.2

  3444-RCS2-YEAR host name

  no ip Routing

  USH - DM IP domain name

  DHCP excluded-address IP 192.168.129.81

  IP dhcp RCS2 pool

  network 192.168.129.80 255.255.255.248

  router by default - 192.168.128.1

  Rental 2 0

  interface BVI1

  IP 192.168.128.171 255.255.254.0

  no ip route cache

  default IP gateway - 192.168.128.1

  ---------|---------|---------|

  Thats the DHCP Pool range 192.168.29.88 through 192.168.28.95

  Well this will confuse your customers.

  And this is NOT how to set up your "range".   See below:

  DHCP excluded-address IP 192.168.29.1 192.168.29.87

  DHCP excluded-address IP 192.168.29.96 192.168.29.254

  IP dhcp RCS1 pool

  network 192.168.28.211 255.255.254.0

  router by default - 192.168.28.1

  Rental 1 0

• Updated standalone Cisco Aironet lightweight mode Access Points

  I'm trying to convert a stand-alone Aironet 1200 in light Mode. I use the tool to upgrade v1.0 proposed by Cisco. But when I put the name of the recovery LWAPP Image (c1200-k9w7 - tar.123 - 7.JA2) in the tool window to update it doesn't work. It is said: c1200-k9w7 - tar.123 - 7.JA2 - LWAPP recovery Image file size is zero. But its size is 4.6 MB!

  Can someone help me?

  Convert the Aironet 1200 of autonomous light mode follow the procedure set out in document http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp23144.

• Aironet 1200 series - power of the weak signal near AP

  I recently bought an access point of the Aironet 1200 (AIR-AP1231G-A-K9) series and the initial setup - IP configuration on the AP, the installer does a SSID and turn on the radio.

  I used my laptop to connect to the SSID that I created, but to my surprise the signal strength of my SSID was only 2 bars and sometimes 1 bar and I'm within 2 feet of the access point. However, the speed of connection/signal quality was varying between 24 Mbps and 36 Mbps.

  Why is the signal strength so low?

  Is is because I did not buy them with external antennas?

  I missed something during the initial Setup?

  Y at - it an option that I have change/fine adjust in the GUI to get the best signal strength?

  Help, please.

  "Is is because I did not buy them with external antennas?

  Yes, that's correct. There is no internal antennas on this model of AP.

  You need at least one, preferably two antennas of the same type for each radio. If you have the old 'A' radio with the paddle antenna, then you only need one or two antennas of radio 2.4 G.

  Good luck

  Scott

• Cisco Aironet 1200

  Hi all

  If there is no link on the compatibility between Aironet 1200 and 3rd party Wireless LAN adapt?

  Thank you

  MAK

  Hi Mak

  The next page shows the wireless providers that support the cisco extensions

  http://www.Cisco.com/en/us/partners/pr46/pr147/partners_pgm_partners_0900aecd800a7907.html

  I don't think that there is a page that shows all the wireless providers who work with aironet products

  Rgds

  Paddy

• I have remove the IOS of the aironet 1100 series by mistake and now I need to copy the IOS image file

  Hello

  I have a cisco aironet 1100 Series wireless access point.

  by mistake I delete the IOS of the router and now I need to copy the IOS image again on it.

  I need your help please.

  For now, he has the Ethernet led RED, Green State, Rdio RED. T no Cisco IOS image file the spirits).

  I downloaded the file c100-k9w7 - mx.123 - 8.jed

  and I download the tftp (tftpd32) servers

  I have the router connected directly to a pc with the static ip address of 10.0.0.2

  but the problem is actually that I don't need the 1100 router ip address right now, I can't access it through a web browser.

  and by a tftpd32 I try but no function.

  I don't know what I'm doing wrong.

  other things, it's that I did not find a clear manual on how to use a tftpd32 to transfer the file to the cisco router 1100 series.

  Thank you.

  I'll wait your hepls.

  Convert a standalone Lightweight Access Point
  http://www.Cisco.com/en/us/docs/wireless/access_point/conversion/LWAPP/upgrade/guide/lwapnote.html#wp161272

• Cisco Aironet 1700 unsupported in the IP 2.1.1

  Cisco Aironet 1700 is not supported in PI 2.1.1; no idea if there is an update in the roadmap?

  Thank you

  Go HERE.

   *** Cisco AP701E is not supported by Prime Infrastructure 2.1.1. Also, Cisco Aironet 1700 Series Access Points are not supported by Prime Infrastructure until Prime Infrastructure Release 2.2, which is yet to be released.

  2.2 IP's schedule release any time December 2014 or 2015 January.

• Stand-alone configuration of Cisco Aironet 700i

  Hello

  I'm well aware new products Cisco. So please forgive my basic questions.

  I have Cisco Aironet 700 series AP(AIR-SAP702I-Q-K9). I don't have a controller. I need to set this up as standalone access point.

  I tried all the basic steps and tried to activate the two radios, but no luck. Anyone can guide me please on how to configure the AP.

  I use web access to configure the AP.

  Help, please

  Thank you

  Sagar

  Hi Sam,

  Please check these messages to set up autonomous AP.

  https://rscciew.WordPress.com/2014/05/24/single-SSID-configuration-on-au...

  https://rscciew.WordPress.com/2014/05/24/multiple-SSID-configurations-on...

  Concerning

  Remember messages useful rates

• Aironet 1100/1200 series and Windows

  Is it possible to use the Windows IAS Radius with Aironet 1100/1200 Series light? If yes are there problems you may need to pay attention to?

  Respectfully

  You can use the server Radius IAS for LWAPP. I'm not aware of any questions.

  Someone else can add to this.

  -> Sushil

• How to upgrade IOS for Aironet 1252 G

  I'm trying to update the IOS for Aironet 1252 G wirless access point, I look at all the instruction and they do not make sense! And there is just no instuctions on how to upgrade the IOS in the WEB BROWSER interface. I just did an install of Windows Server 2008R2 and real simple compared to only raise AP and running, but there still Microsoft and their staff try to keep things simple for people where CISCO makes more complex theings.

  Hello

  If you try to update the IOS on a Cisco AP upgrade recomeneded uses the cli via a telnet session or console.

  **************************************************************************** RECOMMENDED UPGRADE TROUGH CLI: The following are the proper steps to do an IOS upgrade in a CLI/Telnet session (This is the recommended upgrade): 1st: Use a TFTP server in the computer that you are going to use for the upgrades. If you don't have one, get the free TFTP server in the following link: http://tftpd32.jounin.net Note: Make sure that the computer and the APs are in the same subnet. For example and AP in default settings will have IP: 10.0.0.1, so you need to have the computer as IP 10.0.0.2, subnet mask: 255.255.255.0. 2nd: Download the IOS image from the Cisco.com Web site. Note: Do not "unzip" the image. 3rd: Open the TFTP server (make sure that the TAR file's name of the IOS image is shown as in the web site, because sometimes it gets renamed to "Download .tar" and if that happens you need to rename it).  Browse the TAR file and select it, then click ok. 4th: Telnet the unit, go to enable mode and enter the following command: ap#archive download-sw /overwrite /force-reload tftp://IPAddress of_the_tftp_server/name_of_the_IOS_image_you_downloaded In this link, you must specify the extension, as an example: ap#archive download-sw /overwrite /force-reload tftp://10.0.0.2/c1200-k9w7-tar.122-13.JA.tar Note: The IOS image name is case sensitive, and it should be complete.
  
  ******************************************************************************
  
  This is the same procedure for any AP in IOS mode, the difference would be the image used for each specifc model. 

• Cisco Aironet SAP1602E - changing open to WPA - PSK access remote (RAP and map)

  I currently have a deployment of Cisco Aironet SAP1602E Wireless point to point bridge (bridge using RAP and card, root wireless and Non-Root Bridge) to expand a layer 2 VLAN from one building to the other. It currently operates uisng open authentication and encryption - and is administered remotely via the bridge of root, to get wireless (manage) the bridge Non-Root - RAP wireless remote.

  Try to configure the PSK WPA2-PSK remotely via the GUI or CLI - first setup - I informed a similar error to her below indicating that:

  Error: Key-management WPA is requried for WPA-PSK

  Read around, it seems, there is a configuration-control problem, and that I need to specify the mode as WPA2-PSK first, before then being able to specify the PSK there instead of using. However, as soon as this mode is specified on RAP, my remote administration is broken - as probably the RAP try to use WPA2-PSK to look for a PSK, which has not yet been configured. Am I missing something obvious here, or is the order of operations of CLI (1] convert to WPA - PSK; (2] shared secret to apply PSK) as a migration from open to WPA2-PSK cannot be configured remotely (short of preparation of a startup-config; TFTPing presents more; and issuance of a 'reload' remote control)? Can someone please enlighten me as to what the logic is here - no doubt I should be able to specify a PSK first (fo without worrying if I use WPA, WPA2 or other), and then be able to specify that I want as the layer of encryption (WPA) to make use of this pre-parameter PSK? If it was a router, you don't can me to add something to the authentication key chain OSPF; before clarifying its use - why so different Aironet Wireless IOS?

  You're right, and because you will have to enter several lines of configuration to switch to WPA2-PSK with AES didn't really matter; the AP would reset the radio anyway because you make changes related to the radio interface. It would be very useful that if Cisco router/switch IOS 'macro' feature available AP thus in changes like this, unfortunately this is not the case.

  Start with the nonroot AP and make sure that the following lines are added to your configuration. If you add by the console, the order must be like that, do it by downloading a new configuration of booting with tftp, that it does not matter.

  interface Dot11Radio0
  encryption ciphers aes - ccm mode

  SSID dot11 TEST
  authentication wpa key management
  WPA - psk ascii 0

  Please rate helpful messages... :-)

• Change BVI subnet on POE 1200 series

  I have a 1200 Series couple I want to find a way to manage remotely. I could go on a plug in a cable, but I just want to know the order of the steps to follow.

  I need to change a vlan existing devices from XX to YY then change the Virgin British Islands up to her also to the AA. The problem I have is that they're POE so when I change the BVI I lose power and they reboot with original settings.

  I thought that the process would be;

  -change the IP BVI so its in the new VLAN YY

  -change of sub interfaces to match

  -change the vlan native on the kernel to match

  The unit stops and restarts before I can finish. Any tips?

  You must put this in config unless you just want to have a basic config.

  Sent by Cisco Support technique iPhone App

• Impossible to find a stand-alone image for Cisco Aironet 1140

  Can someone give a link?

  -JeIlMa

  Here you go:

  http://tools.cisco.com/support/downloads/go/PlatformList.x?sftType=IOS+Software&mdfid=282439881&treeName=Wireless&mdfLevel=Model&url=null&modelName=Cisco+Aironet+1140+Access+Point&isPlatform=N&treeMdfId=278875243&modifmdfid=null&imname=&hybrid=Y&imst=N