Update OS PIX

Similar Questions

• DHCP & Pix 501

  I currently use a Pix 501 in a SOHO environment with a DSL to non-static. I configured the IP address correctly - outside setroute dhcp ip address. The problem lies in my access lists and static routes. Is there a way to have the pix automatically update these when outside IP changes? Areas of distress are...

  access-list 101 permit tcp any host xxx.xxx.xxx.xxx eq smtp

  acl_out list access permit tcp any host xxx.xxx.xxx.xxx eq smtp

  static (inside, outside) tcp xxx.xxx.xxx.xxx, smtp smtp 10.10.10.1 netmask 255.255.255.255 0 0

  where xxx.xxx.xxx.xxx is the external IP address. I feel, updated the pix per day will be necessary to take account the ISP change IP, but it would be great if it wasn't!

  Thanks in advance.

  -Brian

  You can use the keyword "interface" in the access lists and static, which will automatically use whatever the IP address is on this interface. In your example, it would be:

  access-list 101 permit tcp any interface outside eq smtp

  acl_out tcp allowed access list any interface outside eq smtp

  public static tcp (indoor, outdoor) interface smtp 10.10.10.1 netmask 255.255.255.255 smtp

  Note You must run 6.3 (3) code to get this option, the new code is available here:

  http://www.Cisco.com/cgi-bin/tablebuild.pl/PIX

  Note also you need not specify the interface name in the static statement, which is the interface name in the materials gleaned.

• What version of PDM (PIX Version 6.2 (4))

  Comrades, I am new to PIX 506 ongoing enforcement. I try to get the installed MDP, but I have a bad magic number when downloading ftp!

  Have you tried "downgrading" of worm 6.3 (5) and 6.2 (4) worm. Should what version of PDMxxx.bin I use. Have you tried ver 6.3 (5) install pdm - 304.bin, but who doesn't either. I'm new on this and are studying for my CCNA!, so please have mercy!

  For PIX OS 6.3.5 (pix635.bin), you will need the PDM (pdm - 304.bin).

  Whan you download the FTP image on your PC do not forget that you are in binary mode, if you are in ASCII mode, the image will be corrupted (incorrect checksum).

  FTP x.x.x.x

  loged in...

  bin

  hash

  get a pdm - 304.bin

  #########...

  output

  You use TFTP to download the image to the pix.

  For use PDM:

  pixfirewall # copy tftp://Your_TFTP_Server_IP_Address/Your_pdmfile_name flash: pdm

  Or you can enter the generic command and follow the instructions:

  pixfirewall # copy tftp flash: pdm

  For use of PIX OS:

  Example - updated the PIX Firewall with the copy flash tftp command

  pixfirewall # copy tftp flash

  Address or name of remote host [127.0.0.1]? 172.18.125.3

  Source [cdisk] file name? pix611.bin

  copy of tftp://172.18.125.3/pix611.bin to Flash

  [Yes | No | new]? Yes

  !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

  Receipt 2562048 bytes.

  Delete the current image.

  2469944 bytes of the image of the writing.

  !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

  Image installed.

  pixfirewall #.

  PIX and PDM upgrade guide:

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_tech_note09186a0080094a5d.shtml

  sincerely

  Patrick

• PIX 501 basic Config

  I'm putting in place an internet service for some members of the service here in Afghanistan. We use the commercial internet (provided by satellite) to a modem that goes into my firewall 501 pix.

  Service that we bought gives us Ip 29, and now I just have it set up as such.

  Modem gateway: 10.124.48.1

  Outside the firewall: 10.124.48.2

  Inside the firewall: 192.168.1.1

  Global NAT pool: 10.124.48.3 30 (the rest of intellectual property s that are outside the package)

  On the inside of the pool of the host: 192.168.1.2 -.33

  DNS for inside customers: 192.168.130.30,.50

  Everything seems ok, as I use the PDM software to allow all traffic ip from outside to inside (I know it isn't the safest to do thing ~ and the fact that I turned a firewall $ 700 to a router for $40). I can browse the internet, but it is really weird.

  I.E.

  I can ping msn.com and www.msn.com , and it resolves the twice,

  But if I put msn.com in Internet explorer, it says cannot display the page, but if I hit the refresh like five times, it'll happen. If I navigate away from the page and then try to type in msn.com again (in the same window) I hit refresh 5 times, to get the next page.

  But if I type in www.msn.com it just generally well upward.

  Even when he says that the page cannot be displayed, I have her pinger running in background ~ so I know that I can get for it. Weird huh?

  I also have a question about licenses. When I get the pix firewall information, it says inside hosts: 10 but he let's have me 32 s ip for inside hosts. Does this mean that I'm having problems when I have more than 10 users browsing through the firewall? Or is that what I have as many hosts ip s?

  Thanks in advance for any assistance.

  1.) to refine the 10 limitation of host within the network you couold install another device inside network that PAT - translation of Port addresses that hide all the IP addresses behind his foreign address.

  All PC-> [device router/PAT] - [PIX Firewall] - [router]-> Internet

  (2.) to buy/pbtain a license longer write a mail to:

  mailto:[email protected] / * /

  The product update:

  PIX-501-SW-10-50 = software upgrade license for 501 10 to 50 users PIX = approximately 340$ US

  PIX-501-SW-10-UL = software upgrade license for the 501 user 10-for-unlimited PIX = about 400$ US

  3.) World normal political deadlock depends on your company security policy, someone should set one, many companys trust their employees and allow all outgoing traffic. Might be good to block traffic P2P, Multimedia Streaming stuff, but this is not possible with OS 6.3.4 Release. You must wait for PIX OS 7.0, which is not available for PIX 501.

  sincerely

  Patrick

• How can I see my pix (4.4) flash size?

  I want to update my pix of 4.4 (7) to 6.x.And to my pix520 to have at least 16 M flash and RAM of 32 M.

  But I don't know the size my pix520 flash.

  should what command I use?

  Check in the FAQ at this link

  http://Cisco.com/en/us/products/HW/vpndevc/ps2030/products_qanda_item09186a0080094874.shtml#software1

  How to determine the amount of memory Flash has my PIX?

  A. Si you make a show version command on your PIX, and the size of the Flash is not given in MB, then use the table below to see how Flash has your PIX.

  i28F020 512 KB

  AT29C040A 2 MB

  2 MB Atmel

  i28F640J5 8 MB - PIX 506 16 MB - all other PIX

  strata 16 MB

  For example, if your output of the show version command looked like this:

  Cisco Secure PIX Firewall Version 5.1 (1)

  Updated Friday, October 1, 99 13:56 by pixbuild

  pix515 up to 4 days, 22 hours and 10 minutes 42 seconds

  Material: PIX - 515, 64 MB RAM, Pentium 200 MHz processor

  Flash i28F640J5 @ 0 x 300

  BIOS Flash AT29C257 @ 0xfffd8000

  0: ethernet0: the address is 00aa.0000.0037, irq 11

  1: ethernet1: the address is 00aa.0000.0038, irq 10

  2: ethernet2: the address is 00a0.c92a.f029, irq 9

  3: ethernet3: the address is 00a0.c948.45f9, irq 7

  Features licensed:

  Failover: enabled

  VPN - A: enabled

  VPN-3DES: disabled

  Maximum Interfaces: 6

  Serial number: 123 (0x7b)

  Activation key: xxxx

  The amount of memory Flash is 16 MB.

  See you soon,.

  Paul.

• (Pixie palm) Try to update webOS 1.3.5.1 (unpacking...)

  Miss me the CLOCK of my new Pixie of Palm app. Reading that I need to move to the 1.3.5.1 webOS.  I clicked on the 'Upgrade' and says it is downloading... sitting there forever.  I finally gave up and turned the phone off and on again.  Now when I go to 'Upgrade' it says "Unpacking" and never does anything more than that.

  I'm doing something wrong?  I am in desperate need of the CLOCK (wake up) app.  Thought it was a mistake on this phone because I had it on my razor phone stupid before changing for this one.

  OK, exceeded the update problem (guess you must have a full battery to get download and install it.)

  But still no CLOCK app he shows in my list of applications software, but not as an icon on my Launcher.

  Also, not that I'm 1.3.5.1, when I go to the app catalog, I get the large yellow triangle that says: "this action was not successful. Try again later. »... I have internet connectivity, so not sure what is the problem.

• Just got a new Pixi, updated to 1.3.5 update and now I can't download apps

  Hello!

  I just bought a Pixi yesterday and downloaded a few apps (Facebook, Flixster) and everything was OK.  I noticed Facebook saying that I had to update to WebOS, so I did.

  After the installation of WebOS, I can't download apps.  I followed the palm offers fixes and none of them helped.

  I rebooted my phone a few times (both by choosing reboot and turning off and on again), put in my credit card information and checked for if sure I have a spare bedroom (say 7 GB of free...) and I can't download apps.

  I tried the free and paid apps.  Download including Pandora, enjoy Sudoku, crossword, Accuweather and GoodFood... and none of them.

  I get no error message at all.  I click on the download button, it displays "Download" and then it switches back on a Download"" button.  He will ask me if I agree the application using location services, too... but nothing will download.

  I looked through the forums and couldn't find something relevant?  It seems most of downloads problems producing some sort of error.  Here, I get nothing.  And before the 1.3.5 update, I was able to download apps very well.

  Any ideas?

  Just came across other people having this problem with the pixi. Seems to be related to the pixi only. And it was the people who had no installed 3rd party settings. This solves the problem for all who have tried so far. Run webos doctor found at the link below. Follow the directions. You must back up all files stored on the USB of the Pixi drive. Music, you took pictures, files, etc. Also, be sure to run the backup application in the Launcher to a current backup before wipe everything with the webos doctor. I would like to know if it works for you.

  http://www.Palm.com/us/support/downloads/pre/RecoveryTool/webosdoctor_dl_pixi_sprint_en.html

  Message edited by tagz on 31/12/2009 21:32

• availability of worm 7.01 pix 501 is not updating

  Hi all

  We use 7.0 (1) Version of Cisco PIX

  Version 5.0 device management (1)

  check the availability of pix using the show version command

  This is display up to 49 days, 17 hours, stuck on her and does not update

  all the advice, you will enjoy

  Thank you

  Hello..

  1 - download the file to a system and has application for TFTP

  2 - as always make a backup of your configuration

  copy running-config tftp

  3 - from the command-line on the type of PIX in

  Copy tftp flash... and follow the instructions.

  4. - when the image has been downloaded then use the boot system command to indicate which image should be used when the charging system.

  flash boot system: /.

  4 - reload the PIX

  I hope that helps... Rate if he does!

• After the 1.4.5 update Pixi sounds do not, no camera, no music

  After my 1.4.5 update I came across some problems.  My phone rings (in vibrate it will vibrate again, and when it is on my Touchstone and vibrating, it makes this ringtone with muted sound), the camera won't take pictures, and also I do not get audio applications (like music, alarm signals, etc.).  Also, I just tried Youtube and it doesn't work either.

  Any suggestions?  Is it possible to reverse the last updated?

  My Pixi is on Verizon Verizon 1.4, WebOS 1.4.5 config

  Thank you.

  I would say that webOS Doctor to charge webOS 1.4.5 on your Verizon Palm Pixi Plus edition running.

  You can start the process here.

  Alan G

• Update of new PIX of FO

  I have a single PIX of YOUR 515e 6.3.3 running in production. I add a PIX 515e FO, but it runs 6.3.1. I tried to add an IP address to the new PIX of FO, he accepted the configuration and the inside interface had a link with my laptop. But the TFTP and ICMP traffic won't play on the PIX. How to go 6.3.3 without UR PIX PIX of FO.

  Try to make an "active failover" on the pix without connecting it to the production network.

  I hope this helps.

• The PIX software update

  To upgrade the software on the PIX 515, I just need to publish the following:

  copy the flashftp://172.16.6.100/pix622.bin t

  and then reload?

  Seems too easy.

  What is your current image? If its 5.1 or higher, then you are fine with your orders. If before 5.1, then you still have work to do (because they have no copy command. Need to start monitoring and upgrade mode in this mode). In addition, you are tipping? If so, first make the secondary pix (cables, upgraded, reconnect, disconnect active, upgrade, plug) then the active primary PIX.

  It will be useful.

  Steve

• Update IOS E PIX 506

  Hello

  I have a 506th pix, with 6.3 (4) version of ios. What would be the next or last version I can go to my box would be favorable.

  Correct me if m wrong, I heard that I can't move my box to PIX IOS 7...

  see you soon

  Ramp

  Hello

  The last version that supports the 506E is 6.3 (5) - Although it was matter of getting the 506E to support version 7, that he has not appeared and with the release of the ASA 5505, I suspect 6.3 (5) will be the latest version.

  HTH

  Andrew.

• PIX 515 pix704.bin pix721.bin update...

  Hello

  I was able to get to the 7.04 6.3 upgrade successfully. I loaded the version 7.21 with the boot system command and made a wr mem. When I reboot I still get up to 7.04... can someone help here?

  TIA,

  Gary

  Gary,

  For after the "show bootvar", you have the pix configured to

  1 load the code of 7.0 (4) if it is available in flash or

  2. load the code 7.2 (1) if 7.0 (4) is not available.

  You get the error message below "ERROR: unable to set this URL, it has already been set." Remove the first instance before adding this one"because the pix is already a" boot system flash: / pix721.bin "set.

  Given the question, I "think" that your configuration on the pix has the lines below. Please correct me if I'm wrong. The order of configuration lines are very important when the pix attempts and load the image.

  Flash: / pix704.bin starting system

  Flash: / pix721.bin starting system

  If the above configuration is true, then the pix will try to load first 7.0 (4) and if 7.0 (4) is not available, the pix will charge 7.2 (1)

  If you want the pix to load 7.2 (1) first, you will need to

  1. Remove "boot system flash: / pix704.bin" by not doing a "no boot system flash: / pix704.bin.

  2 then do a 'sh run"and make sure it is stated as a boot that is" boot system flash: / pix721.bin.

  3 then add the command "" boot system flash: / pix704.bin.

  4. now make a race of show and make sure that the initialization statement looks like this in your configuration. The order of statements is very important.

  Flash: / pix721.bin starting system

  Flash: / pix704.bin starting system

  5. make a "wr mem".

  6 reload the pix and the pix then try to load first 7.2 (1).

  This should solve your problem. If this isn't the case, please report the error you receive and we will try and solve the problem.

  I hope it helps.

  Kind regards

  Arul

• Graph of Firefox ridiculously furred after update

  I installed Firefox on Kubuntu (38.0 package version + build3 - 0ubuntu0.14.04.1). After the upgrade, the Firefox UI everything is furred. Tabs, icons, everything. Given zero has not set the problem. A screenshot should be attached, although I seem to have a lot Uploader.

  Thanks for the screenshot. Another user posted about this earlier today: default zoom is too big (unsolved). I will repeat my comments here where they help.

  I think that your distribution contains platform-specific extensions, then I suggest to test with those disabled in case there is a compatibility issue with Firefox 38. One way to do that is to run Firefox Safe Mode. It is a standard diagnostic tool to disable some advanced features of Firefox and extensions. More info: questions to troubleshoot Firefox in Safe Mode.

  Does not work if Firefox: Hold down the SHIFT key when you start Firefox.

  If Firefox is running: You can restart Firefox in Mode safe mode using either:

  • button "3-bar" menu > "?" button > restart with disabled modules
  • Help menu > restart with disabled modules

  and OK reboot.

  Two scenarios: A small dialog box should appear. Click on 'Start mode safe' (not update).

  Any improvement?

  If this makes no difference, you can try to adjust the setting for the support of high-resolution, which functions as a zoom factor:

  (1) in a new tab, type or paste Subject: config in the address bar and press ENTER. Click on the button promising to be careful.

  (2) in the filter box, type or paste the pix and make a pause so that the list is filtered

  (3) preference layout.css.devPixelsPerPx is usually set to-1.0, which means use the system default value. You can change this to 1.0 for the return of 96 DPI and see if that's what you prefer. And you can increase the size of there by slices, for example, 1.1 for a total zoom of '110% '.

  Please be careful not to set this value to something tiny, because it can be difficult to recover from that.

• FF 27 - my fonts are pixely and I can't understand why.

  Hello friends,

  About 4 weeks ago, fonts on all the pages I visit using Firefox became pixely (some letters appear in bold, the lines seem to be low resolution, etc.). I tried the following steps to fix without success:

  -Update of FF 27
  -Reset by default
  -Turn off hardware acceleration

  Here is a link to a comparison of the FF27 vs Chrome vs IE screenshot: http://i.imgur.com/f8EBC6p.png

  The only thing I can think of that may be the culprit, it is at the same time, I got a new monitor that requires a display installed on my laptop driver.

  What other troubleshooting measures can I take to help address the display of police while I use my beloved Firefox?

  Any help is appreciated.

  Thank you.

  Try to play with this:
  =

  layers.acceleration.disabled: True
  

  And make sure that firefox has the updated driver, you can check in "subject: support.

  and try turning off hardware acceleration: try disabling graphics hardware acceleration. As this feature has been added to Firefox, it has gradually improved, but there are still some problems.

  You will have to perhaps restart Firefox for it to take effect, so save any work first (e.g. you compose mail, documents online that you are editing, etc.).

  Then perform the following steps:

  • Click on the orange top left Firefox button, then select the 'Options' button, or, if there is no Firefox button at the top, go to tools > Options.
  • In the Firefox options window, click the Advanced tab, and then select 'General '.
  • You will find in the list of parameters, the checkbox use hardware acceleration when available . Clear this check box.
  • Now restart Firefox and see if the problems persist.

  In addition, please check the updates for your graphics driver by following the steps in the following knowledge base articles:

  • Troubleshoot extensions, themes, and issues of hardware acceleration to resolve common problems of Firefox
  • Update your graphics drivers to use hardware acceleration and WebGL

  This solve your problems? Please report to us!

  Thank you.