Update portable drive to SSD, problems with the installation of operating system and recovery system

Similar Questions

• Qosmio F30-114 - a problem with the installation of operating system

  Hi all
  I have a problem during the installation of operating system from the recovery disk (Win XP Media Center Edition).
  After loading the disc, I seen the installer welcome window, set up all the parameters in it and pressed the OK button.
  After that, an error has occurred (in a black console window):

  Check the type of partition MBR
  Not FOUND: Partition ID 4 is 0x00 not 0 x 88
  Seeking the TMBR
  No found TMBR!
  Fact.

  Microsoft DiskPart version 5.2.3790.1830
  Copyright (C) 1999-2001 Microsoft Corporation.
  On computer: MININT-JVC

  Disk 0 is now the selected disk.

  Services of disk management cannot complete the operation.
  Specified drive does not exist.
  ERROR: E:\04629R01 Reco-unpacking. TPA has failed!
  Press a key to continue...

  After reading this message and pressing a computer key restarts and that's all that happens.
  Also I can not install another OS (Win 7 for example), during the last part of an installation, I get a message "the work cannot be completed.".

  That's happened? I don't understand what is the reason for this problem. I was reinstall another OS (the drive recovery too) often earlier and everything was OK.

  You can install WXP using the Microsoft installation disc?
  Set the BIOS on the settings by default and to use the recovery disk again.

• Problems with the installation of new system. Need help.

  Hello

  I'm new here so I'm sorry if I posted this in the wrong section, I tried to look for this subject but nothing similar has come so I decided to create this.

  I have a HP Pavilion DV7-1020ea, which came with Windows Vista Home Premium 32 - bit installed and a recovery disk that was on the D: partition, but no real recovery disc/DVD.

  This laptop has had a hard drive failure lately, so I replaced it with a new hard drive cool (320GB, same accompanying).

  The new drive as you probably already know is fresh and it does not all partitions or any information, so without recovery of D: partition.

  I need to mention that the phone was fully functional, keyboard, touchpad, and quicklaunch worked correctly.

  I have some experience with computers, so I know how to recover, set up the startup in the bios etc.

  I tried to install Windows XP Professional 32-bit and Windows Vista Home Premium 32 - bit on my laptop but I found out that the DVD drive makes a funny (not damaged or broken), as a lack of sound recognition. The two systems of Windows are original, and I have a license for them.

  Its different when I try to install WIndows 7, the DVDs are recognized immediately. All system disks work on other computers and work quite correctly. The portable disk drive is not damaged.

  The only thing I saw was: No. Bootable Device (3FO)

  I didn't know what to do so I handed the laptop to an expert.

  When I arrived at my computer back, the computer had Windows 7 Ultimate 64 bit installed, but the problem was that quick launch buttons, keyboard and Trackpad was not working. The only way to use the computer was to plug in an external keyboard and mouse which is not a solution.

  -The keyboard not working outside not BIOS, press No button in text fields do not work. The only functions that worked were when I pressed fn + f8 to make the screen brighter and oddly enough, it worked, so when I pressed the keyboard caps lock, caps lock lights on the laptop keyboard as well.

  -The touchpad itself does not, the keypad or buttons. The only thing that works is the light that changes when I press the button disable from white to red, and then from red to white.

  -The quicklounch does not work. The works of power button (turn on the laptop since it is a button) but the led behind it does not work. For speaker and Wifi light is always red (off) and even when I touch it, it will turn blue/white. The rest has a white light behind her, but does not work.

  I also noticed that when I go into the BIOS, the bios is absolutely slow. It takes about 30 seconds to react when I press the buttons on the right, but also it does not react sometimes and it's like in all sections (but it works for keyboard).

  Later, I went to the Device Manager and discovered that there are 3 basic system devices that are not installed. I tried to install by searching online and locally, but no drivers were found.

  All devices have "the drivers for this device are not installed (Code 28)" and the drivers can be found online or on-site.

  Details of devices:

  Basic device PCI system bus 6, device 0, function 3

  Basic device PCI system bus 6, device 0, function 1

  Basic device PCI system bus 6, device 0, function 4

  Trying to fix my keyboard, the touchpad and quicklaunch buttons I went on Synaptics website to download the drivers for the touchpad, updated it, restarted, did not work. I also went on the official site of HP to download the drivers for quicklaunch to my computer, keyboard and mouse, put up-to-date, did not work.

  I also tried to put in the DVD of Vista and XP DVD to see if the computer is able too see them at all, but when I went to my computer and looked at the DVD player, it says "Insert disc in drive E:." so none of them have been recognized by the computer.

  I don't like Windows 7 and I would really like to have my laptop runs on my old system which is Windows Vista Home Premium 32-bit with keys on keyboard, keypad, tactile and functional quicklaunch.

  Could you help me then install the Vista drivers or to solve this problem?

  Tank you!

  You are the very welcome.

  See if the chipset driver installation done something to help.

  https://Downloadcenter.Intel.com/Detail_Desc.aspx?AGR=Y&ProdId=816&DwnldID=20775&keyword=chipset+installation+utility&lang=eng

  It would be the only suggestion I can offer.

  I think you have a motherboard problem or something related.

• Can I just create a virtual machine with the installation of operating system and Application in an external drive?

  People,

  Hello. I use VMPlayer to install virtual machines a few OS in my laptop.

  Because my laptop's hard drive space is not enough to create a VM more to install Oracle Linux and its Application, can I just create a virtual machine in my laptop and then install Oracle Linux and its Application in an external USB disk?

  You can create and save the Virtual Machine in any place that you have read & write access to and enough space to support what is being installed.

• If there is a problem with the temperature of my system if I update to Windows 7 Professional 32 bit in HP Pavilion dv6330ea laptop?

  Hello

  Model No. - HP Pavilion dv6330ea laptop. Check out the link http://h10025.www1.hp.com/ewfrf/wc/product?cc=us&d

  I bought my laptop in UK and I intend to improve my system Vista Home Premium 32-bit to Windows 7 Professional 32-bit.

  In some forum users have mentioned that.

  Users with nVidia graphics card should check the temperature of this device before upgrade.

  In this way you will know is it works fine under Windows 7 also.

  How you can check your laptop CPU (processor), the GPU (graphics card), the motherboard or HARD drive temperature?

  To do this use HWMonitor (free and recommended) or Aida64.

  Q1] what is the minimum temperature / best should have the CPU and GPU, motherboard, HARD drive?

  Q2] is that this temperature is sufficient to upgrade to Windows 7? It will create no problems after the upgrade to Windows 7? This is the value of the temperature of my system of CPUID Hardware Monitor v1.22

  Motherboard - Quanta 30BC

  Temperatures - THR1

  Value - 46C (114 F)

  Min - 46C (114 F)

  Max - 62 (143 F)

  Inter Core Duo T2350

  Temperatures - Core 0

  Value - 41 c (105 F)

  Min - 41 c (105 F)

  Max - 64 c (147 F)

  Temperatures - Core 1

  Value - 41 c (105 F)

  Min - 41 c (105 F)

  Max - 64 c (147 F)

  Hard drive - ST9250315AS

  Temperatures - Assembly

  Value - 48 c (118 F)

  Min - 48 c (118 F)

  Max - 49 C (120 ° F)

  Temperatures - Air flow

  Value - 48 c (118 F)

  Min - 48 c (118 F)

  Max - 49 C (120 ° F)

  Please answer that will help me to decide whether to proceed with the upgrade to Windows 7 Professional or not of the HP Pavilion dv6330ea notebook PC

  I found a solution to my own post...

  Finally installed Windows 7 and noticed that the temperature is low compared to vista.
  So would like to inform all users with queries concerning questions of temperature on PC portable Hp Pavilion dv6330ea proceed with the installation of windows 7 and temperature is very low, the startup is fast, ahead of the functions that is good in windows 7 over vista.

• HP Envy 17-2100ed: problem with the installation of a driver on my laptop

  Dear readers,

  I have some time for problems with the installation of the drivers on the HP site. Whenever I chose a driver, such as for the Cyberlink Youcam software, the download process will be blocked at 28.9 MB, a total of 154 MB. I also tried to install the software for my HP printer, but once the same question.

  Can someone help me? Thanks in advance!

  Kind regards

  Amir

  Hello @Amirkalloe,

  Thank you for visiting the HP Forums! The Forums are a great place where you can find solutions for your problems, with the help of the community!

  I came across your post about the problem of driver and he wanted to help!

  Problems installing drivers, or by downloading the drivers?  If you have problems to install the drivers, you can use the tool on the following site:

  Open the Windows Update troubleshooting tool

  Let me know how it goes.  Please let me know if this information helps you solve the problem by marking this message as 'accept as Solution', this will help others easily find the information they seek.  In addition, by clicking on the Thumbs up below is a great way to say thank you!

  Have a great day!

• problem with the installation of the updates updates 12

  original title: problem with installing updates 12 updates, impossible to install, but all others have taken

  I have a problem with the installation of updates, some have taken while 12 others impossible to install.  I tried the Mr. fix, but will not be too much work.

  Hello

  1 did you change on your computer?

  2 are you able to install some other updates?

  Method 1:

  Try to reset the Windows Update components

  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 how to back up and restore the registry in Windows

  How to reset the Windows Update components?

  http://support.Microsoft.com/kb/971058

  Method 2:

  I also suggest you perform the clean boot and check.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: After a repair, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

  Method 3:

  I also suggest you to see link and check.

  Problems with installing updates

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-installing-updates

• Satellite L875-13D - problem with the installation of the wireless card

  Hello

  I bought a Toshiba Satellite L875-13D. I installed Windows 7 Enterprise edition.

  I have a problem with the installation of the wireless card. I have downloaded the driver on Toshiba website, but it does not work. When I run the file .zip and .exe, nothing happens. In addition, there are several pilots: Athos, Intel and Realtek and I do not know what is mine... I test all the driver but same result.

  I have the same problem with Bluetooth driver that does not work too.

  Thank you for your help.

  > But it does not work yet for Bluetooth,... I have install the driver by the .exe from the Toshiba Web site but when I run the application, I have error that says missing tosbtapi.dll. I founded and downloaded and installed on budget3 and SysWOW. But after that, the installation is blocked. Any ideas?

  Laptop Satellite L875-13D isn t equipped with Bluetooth.
  Didn t you know who?

• Problem with the Installation of JAVA in my new Dell running Windows 7

  Problem with the Installation of JAVA in my new Dell running Windows 7 - error message when you try to intall Java using Chrome.

  "lib'charsets.jar: old file not found."  However, a file of the same name was found.  No updates since the contents of the file do not match. »

  Then "Java update fails to apply the changes to your system."

  Then "error 1722.  There is a problem with this Windows Installer package.  A fun program as part of the Setup did not finish as expected.

  Earlier, I had a problem with the video and had Windows reinstalled 7.  Now my AOL games don't show/reading.  JAVA said error 1722 is an InstallShield error code. It indicates that the installation process has failed. The exact reason for this error is not known at this time.  I was told to uninstall JRE (Java Runtime Environment).  I find two versions of Java on my system (no JRE) - Java (TM) 6 - update 14 and 14 (64-bit).  Should I uninstall both?... OR WHAT?

  Hi Betty48228,

  Here's how to solve your problem:
  (1) uninstall all versions of Java.
  (2) the uninstall will probably fail. If so, get Revo Uninstaller free http://www.revouninstaller.com/revo_uninstaller_free_download.htmland uninstall Java in advanced mode (integrated Java uninstaller runs, failure and then Revo will delete everthing manually). You will need to restart your PC.
  (3) reinstall Java: http://java.com/en/download/

• Problem with the installation of the webcam VX2000

  problem with the installation of vx2000.  After installation, I hit finish and get error Lifecam.exe has encountered a problem and needs to close.  The program is installed and the icon on my desktop but when I try to open it I get the error.  There is no Logitech drivers installed, have the latest version of the driver, uninstalled/installed in many times, did a clean boot.  Tried on another computer (same operating system) cam and installed and worked perfectly.  Reformatted the drive on my computer and and had the same problem error once again.  Checked the error reports and it shows kernel32.dll as the defective module but it, s not to be missed in System 32.  It may be corrupt and I would like to replace it.  If anyone can shed some light on this problem it would be greatly appreciated.  Thanks, Max

  Hi Max1215,

  Follow the steps in the article.

  Troubleshoot failures to find the new LifeCam hardware

  Troubleshoot installation of Intellipoint and IntelliType LifeCam software

• I have a problem with the drag (cursor snap) video and audio stuttering!

  I have an emachine windows vista home edition and have caused problems with the drag (cursor snap) video and audio stuttering.  my hardware configuration includes an HP printer and a video camera from Microsoft with pregnant beyond the keyboard, monitor, and system speakers routine.  Are there updates or the settings that I can apply to correct this problem?

  http://www.eMachines.com/support/drivers.html

  The latest drivers/software for your machine come directly from eMachines.

  Click the link above for them.

  See you soon.

  Mick Murphy - Microsoft partner

• HPPIW. EXE does not solve the problem with the installation of the complete software for 8500 A909g

  Waterboy71 - sorry for a new position, but the forum is read-only (?) so I can't respond to your response to my problem with the installation of the driver/software 8500 A909g.  By your answer on 5/19, I downloaded HPPIW. EXE and it ran.  It detects my wireless printer, but it tells me that "the selected printer is not supported by this wizard."  Is there another thing I can do to install the software so that I can scan and fax from my Windows laptop 8.1?

  Hello
  If please try following the steps below and check if this can solve the problem:

  1 open the Mcafee Virus and Spyware Protection software you are interested in, click on calendar and perform analyses. Click analysis in real time, and then click stop. Select until I restart the PC and confirm by clicking the button turn off.
  2. open the dialog box run by clicking on the Windows key and the R key on your keyboard. Type %windir%, and then click OK.
  3. type hpoins*.dat in the search bar at top, if there is that no result rename the extention in old instead of dat. (e.g. hpoins1.old)
  4. type hpwins*.dat in the search bar at top, if there is that no result rename the extention in old instead of dat. (e.g. hpwins1.old)
  5. start the Run dialog box by clicking the Windows key and the R key on your keyboard. Type MSIEXEC /Unregister. in the Run dialog box and click OK.
  6. launch the Run dialog box by clicking the Windows key and the R key on your keyboard. Type MSIEXEC/REGSERVER in the Run dialog box and click OK.
  7. run the installation file and check all difference.

  Kind regards
  Shlomi

• Windows cannot print due to a problem with the installation of the current printer.

  Thread title: Epson TX235W will not print

  When I click on 'print', I get the print control. the box that tells the printer how many copies, etc.  When I toast 'print' it get a little box that says Windows cannot print due to a problem with the installation of the current printer.  Try one of the following:

  Check the printer by printing a Windows test page

  Ensure that the printer is online and on

  Reinstall the printer driver

  I did everything above and I get the same result.

  Help!

  Hello

  Did you of recent changes made to your computer that caused the problem?

  This problem is limited to a particular application?

  How is the printer connected?

  Method 1) restart the print spooler service and delete the print queue

  Start the print spooler service in the Services console

  1. Click Start and run, type services.msc, and then click OK.
  2. Right click on the print spooler service, and then click on stop.
  3. Right click on the print spooler service and then click Start.

  Start the spooler service for printing at the command prompt

  1. Click Start, run, type cmd, and then click OK.
  2. Type the following commands at the command prompt:

     net stop spooler
     net start spooler
     Output

  Note: Press ENTER after each command line.

  Cancel printing

  http://Windows.Microsoft.com/en-us/Windows-Vista/cancel-printing

  Method 2) remove and add the printer and then check.

  Add or remove a printer (Applicable for Windows 7)

  http://Windows.Microsoft.com/en-us/Windows-Vista/add-or-remove-a-printer

  It will be useful.

• Windows 7 cannot print - "Windows cannot print due to a problem with the installation of the current printer"

  Window 7, Lexmark 1300 series. Cannot print. When you try to print from Notepad, the error message is "the system cannot find the file specified." What impression of the word is "Windows cannot print due to a problem with the installation of the current printer" have uninstalled and reinstalled all printers in many times. Removed the Lexmark 1300 in the registry and reinstalled. No change. Ran sfc/scannnow several times. Microsoft Fixit print detected no problems. Help, please.

  Hi Baccy138,

  See the methods mentioned below and check:
  Diagnose and automatically fix the Windows USB problems
  http://support.Microsoft.com/mats/Windows_USB_diagnostics/
   
  Try to download and update the drivers manually from this site:
  http://support.Lexmark.com/index?segment=support&UserLocale=en_US&locale=en&ProductCode=LEXMARK_Z1300&page=product&FromPage=null#1
  1. click on the above link and click the menu drop down and select Windows.
  2. Select the version of operating system like Windows 7 and check the bit as a result.
  3. Download complete drivers and install it.
   
  Hope this information helps.

• I tried to install the latest version of itunes with windows 10 but he said "there is a problem with the installation package. A program to complete the installation could not be executed. Please contact the support staff. No matter what guys?

  I tried to install the latest version of itunes with windows 10 but he said "there is a problem with the installation package. A program to complete the installation could not be executed. Please contact the support staff. No matter what guys?

  (1) temporarily disable your security/antivirus software

  (2) download iTunes from the official source: http://www.apple.com/itunes/download/

  (3) try to reinstall

  (4) turn on your anti-virus