Update to Windows 7 SP1 installed, but not in installed updates or system

Similar Questions

• Visioneer OneTouch 8700 USB Scanner Driver for Windows XP SP1 installed SP 2 compatibility mode - does not

  My machine is upgraded from XP SP2 to Windows 7. Support was interrupted by the manufacturer scanner after the pilot XP SP1.   Update of Windows in my system is always sur-installe updates automatically.   The scanner driver has been downloaded from the MFRS. ' site and installed in my computer Windows 7 in "compatibility mode for XP SP2. The scanner icon in my system tray.   To make a physical connection to my system, I get error that it can not be connected or cannot be configured.   I have two USB ports of work attached to the Mo (Chinese-"Weibu") and two USB PCI card is compatible with XP and earlier versions (as shown on the box, no mention of Windows 7).   I tried all these ports, always the scanner does not connect to my system.   In addition, my device manager under USB controllers, shows the exclamation marks in yellow triangles against two elements of the same name: "VIA Rev 5 or later USB Universal Host Controller.   I uninstalled these 2 elements and restarted my system several times, without success.   At each reboot, the yellow marks disappear but soon reappear.  But the scanner worked perfectly fine in my old XP SP 2 system before moving on to Windows 7 and before installing the USB PCI card.

  Is there a solution to this problem up the old USB devices and running in the Windows 7 environment?   (I have a very old IBM PC Camera too that works well in my old XP system, but not yet tried in the current system, even if the driver has been installed).

  If finally I am not able to use the scanner under Windows 7, I reluctantly get Windows XP reinstalled on another drive and boot into it just to be able to use the scanner which is functioning perfectly.

  I am a person of 78 years and enjoy using and experimenting with my PC, which has become an addiction for me.

  Thank you.

  You can buy a copy of XP that would probably cost more to replace the scanner and now is not the right time to install XP anyway.

  Your webcam is a lost cause. Compatibility mode has been designed to work for older programs, and Microsoft does not recommend to use it to install the device drivers. I have no idea why some here suggest a possibility...

• Update that installs get Windows 10 app Windows 8.1 and Windows 7 SP1 KB3035583 is NOT hidden

  Hello

  I have Windows 7 SP1, and because my computer is a netbook (small laptop) with only 2 GB maximum installable RAM, I don't want to upgrade to Windows 10.

  Nor do I want to find that I have any nagging application on my computer, which I find I become obliged often to answer, in order to re - hide the app.

  I have therefore configured as Windows Update settings:

  'Check for updates but let me choose whether to download and install them '

  I then "Hid" update KB3035583,

  and also confirmed that he had been placed in the: dialog "restore hidden Updates.

  I haven't used the system restore from the cache to update KB3035583,

  Yet it often reappears in the list of the optional updates available for installation,

  and then I have to hide it again!

  When KB3035583 reappears in the list of the optional updates, it also is more listed in the dialog box "restore hidden Updates", yet the other updates that I've previously hidden, remain in this dialog box.

  This problem only seems to affect KB3035583.

  This problem is normal?

  Any correction is likely?

  Is there a way to fix this?

  I hope to hear from anyone with a solution.

  Kind regards

  Ray333

  When KB3035583 reappears in the list of the optional updates, it also is more listed in the dialog box "restore hidden Updates", yet the other updates that I've previously hidden, remain in this dialog box.

  This problem only seems to affect KB3035583.

  Because updates automatically a mask itself as soon as MS Review and install a more recent version. I suggest to use use GWX Panel - ultimate Outsider to remove windows 10 messages.

• I am running Windows 7 Home premium but not able to install my Xerox Phaser 3117 printer due to the unavailability of the appropriate driver

  I'm on Windows 7 Home premium, but could not install my Xerox Phaser 3117 printer due to the unavailability of suitable to my lenovo driver all in a desktop pc. Help, please.

  Sandip Mitra.

  There are drivers Windows 7 here:

  http://www.support.xerox.com/support/phaser-3117/downloads/enza.html?operatingSystem=win7x64&fileLanguage=en_GB .

  Make sure that get you drivers 32 or 64-bit according to your version of the Windows.

  * To see if you're running 32-bit or 64-Bit Windows click:

  Start-> Control Panel-> system

  Then look at where it says, "System Type".

• How to download windows xp - sp1 or sp1a - not through the internet

  Help. need to download windows xp service pack 1 or 1, but not through the internet because it keeps failing at half way through the download online.

  To avoid confusion and duplication of effort, please post a follow-up later all replies to your thread of origin-online http://answers.microsoft.com/en-us/windows/forum/windows_xp-windows_install/have-xp-no-service-pack-trying-to-download-sp1-how/831e0dcc-6b42-4242-9f81-cbd156daf856

• lack of cd installation for window vista Home premium, but not the sticker on laptop?

  I don't HAVE THE CD TO INSTALL the windows vista family premium, BUT WHEN I BOUGHT MY LAPTOP and hav, STICKER IS in MY COMPUTER PORTABLE WINDOwS VISTA product key, WHAT should I DO TO GET AN Installer?

  Vista Media recovery obtaining and/or using the Vista recovery on your computer Partition to factory settings .

  There is no Vista free download legal available.

  Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.

  Normally, they do this for a cost of $ small.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.

  See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.

  Normally, you have to press F10 or F11 at startup to start the recovery process...

  Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Or borrow a good Microsoft Vista DVD (not Dell, HP, etc).
  A good Vista DVD contains all versions of Vista.
  The product key determines which version of Vista is installed.

  There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.

  If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  http://support.Microsoft.com/default.aspx/KB/918884

  MS advice on the conduct of clean install.

  http://www.theeldergeekvista.com/vista_clean_installation.htm

  A tutorial on the use of a clean install

  http://www.winsupersite.com/showcase/winvista_install_03.asp

  Super Guide Windows Vista Installation

  After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.

  See you soon.

  Mick Murphy - Microsoft partner

• already purchased windows 7 sp1, I'm not a System Builder now what?

  Do I the OPK, or can I go ahead and install it without all this stuff of OPK? It's my 1st generation and I am the end user.

  Nothing prevents you to use an OEM System Builder License, but it does come with some license restrictions. There is no need to install the OEM preinstallation kit if you use it for yourself.

  The OEM of Windows 7 versions are identical to the versions commercial full license with the following exception:

  -OEM versions don't offer any free direct support from Microsoft technical support Microsoft

  -OEM Licenses are tied to the computer first you install and activate it on

  -OEM versions allow all hardware upgrades except for an upgrade to a different model motherboard

  -OEM versions does not move directly from an older Windows operating system

  OEM licenses must be installed by professional system manufacturers. Under Microsoft's OEM license agreement, they should not be sold to end-users under any circumstances, must be preinstalled on a computer using the preinstallation OEM (OPK) before delivery to the customer and include to the at least the manufacturer contact information. They are, therefore, designed for installation only on a single computer and are not transferable, even if the original computer is no longer in use. This isn't usually a problem for users who buy a new computer, because systems that most pre-assembled systems ship with a preinstalled operating system. There are very few circumstances where Microsoft will allow the transfer of licensed OEM for a non-functional system to another, but the OEM System Builder License Agreement (SBLA), as well as the EULA (EULA) OEM contract don't contain any provision for this, it is entirely at the discretion of Microsoft, depending on the situation

  http://www.Microsoft.com/OEM/en/licensing/sblicensing/pages/licensing_for_hobbyists.aspx

  What is OEM software? :
  http://support.Microsoft.com/GP/oemsupport_1/en-GB

  Licensing FAQ:
  http://www.Microsoft.com/OEM/en/licensing/sblicensing/pages/licensing_faq.aspx

• MS-DOS works with Windows XP - Home Edition, but not with XP-Media edition

  I have an old MS-DOS program that can be run on Windows XP Home Edition, but on my laptop with XP Media Edition, it does not load and gives the following error message:
  NTVDM CPU has encountered an invalid statement:
                    
  CPU: c000 IP: 2956 OP: 0f 00000000

  Y at - it a fix for this problem?

  Hello

  I suggest you follow the steps by Ajay of this link and check if this may help: http://answers.microsoft.com/en-us/windows/forum/windows_xp-performance/16-bit-ms-dos-subsystem-ntvdm-cpu-illegal/4b551cf4-e317-44e6-9e93-20a5c2240497

  It will be useful.

• DVD/cd in Windows XP player plays but not files

  My dvd / cd drive plays but not record. The safety tab disappeared from the properties box. Normally, when you right click on the drive to open the properties box, there should be a 5th tab at the top that says record but this tab is not launched. He disappeared.

  Hello

  · What is the number and the model of the CD/DVD drive?

  You can follow the steps from the link: CD - R or CD - RW drive is not recognized as a recordable device: http://support.microsoft.com/kb/316529

• Clean Windows 7 sp1 install Windows Update, error

  Two different computers. Clean install Windows 7 with SP1, 32-bit.

  Run Windows update and set to be installed other Microsoft products.

  Always get "an error occurred the news updates for your computer"

  8007000E error code.

  Memory insufficient because no other applications are running and no virus programs not installed. Without Language Pack installed by some of the information I found on this code. Clean install.

  The two I'm working on computers are Dell computers. Both we get same error. Very frustrating because I need to raise these two systems up and running.

  Cannot resolve this problem or find a working solution to the problem.

  Please run the Windows Update Troubleshooter:
  http://go.Microsoft.com/?linkid=9830262

  Please provide details of any problem it reports as not fixed.

• Windows Vista SP1 install problem

  Have ultimate Visa on computer and SP1 appears in update as long as 1.9 Mb file {KB936330}. Installation seems to go ok excepy who, after having agreed to be wary of many reboots, is seems to load in a few seconds [appears as update added] with no restarts BUT a few minutes later, the same update appears.

  Tried to get around this by downloading the SP and running of the saved file. Once again, everything seems ok [several reboots this time] until step 3 of 3 is 100% full and the message appears while the SP has not then install the steps are to be set aside. In the end, the 0x800F0826 code appears as explantion. I have treid research on this problem, but to no avail yet.

  Can someone help me?

  Hello.

  Here is some information on this error code:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-windows_update/error-code-0x800f0826-when-installing-Windows/2f034887-C30A-4E2D-9BB7-d07246d6b4ae

  "Windows Update error 800f0826"

  http://Windows.Microsoft.com/en-us/Windows/Windows-Update-error-800f0826#1TC=Windows-Vista

  _________________________________________

  It's the way you normally install SPs without using Windiws update:

  Click Start > right click on computer > left click on properties > see if you have Vista 32 bit or Vista 64-bit installed.

  It will also tell you which SP you have installed.

  Then, choose the download of 'bit' OK to use to install Service Packs, installation of SP1 first if it is not already installed.

  Vista SP1 32-bit (x 86): http://www.microsoft.com/en-us/download/details.aspx?id=30

  Vista SP1 64-bit: http://www.microsoft.com/en-us/download/details.aspx?id=21299

  Vista SP2 32-bit (x 86): http://www.microsoft.com/en-us/download/details.aspx?id=16468

  Vista SP2 64-bit: http://www.microsoft.com/en-us/download/details.aspx?id=17669

  This Information Microsoft can help you resolve problems that you encounter during the installation of Service Packs for Vista.

  http://support.Microsoft.com/kb/947366

  See you soon.

• BSOD has known during Windows 7 SP1 install

  Hello again,

  I recently posted here (LINK) about a number of problems I had with my PC that I assumed were resolved when I discovered my previous hard drive would die quickly, resulting in corrupted, system files etc.

  First of all, a chronology of the mistakes that I started to experience this month: Please see my previous thread (link) for detailed information about the errors here.

  30 April - installed the second module of 4 GB memory (Corsair 4 GB DDR3 1333 mhz XMS3, manufacturer: CMX4GX3M1A1333C9)

  02 may - crash first experienced, uncertain, conditions, as I was AFK.

  08 may - new SATA cable bought as I suspected one that connects my hdisk to my motherboard caused the original crash.

  16 may - first BSOD, it is product in the game.

  Initially, I suspected my module RAM second, newest to be initially, but after a lot of help and advice (see link), I discovered that my hard drive was not.

  Note on RAM: both modules are identical and installed in their recommended media. In the BIOS/DRAM config, they are on Unganged.

  20 may - after buying a new hard drive and install Windows on it I was installing updates (SP1 was among them) when my PC struck a blue screen; I checked using WhoCrashed dump files: ntoskrnl.exe and ntkrnlmp.exe seem to be the culprits - Bugcheck code: 0x1A (0xFFFFFA800488D690, 41790, 0 x 0 x 0, 0xFFFF)

  After the reboot, the update done OK.

  I used the sfc/scannow command found no breach of integrity.

  The next day, I ran Memtest86, making several past - 2 on my old module, 2 on the module of suspects and two with two modules in their default positions (DDR3_1 and DDR3_2). All the tests showed 0 errors.

  I realize that in Memtest past terms 7 or 8 can produce errors where 2 can present a sound module...

  All drivers are up-to-date, or I more not less successful them anything.

  Today (May 22) my PC suddenly lost power and restarted, and the event was almost like a brown-out as it also caused my landline downstairs to turn. It's happened once or twice in about 3 years, and I have no idea what causes it.

  When the PC was trying to start it would not go beyond POST and gave me the following message is displayed:

  Verifying DMI Pool Data...
  AMD data change... Update new data on a DMI interface!

  I had noticed this message several times when I was performing a clean installation of Windows (2 days ago), however, it wasn't a problem then. In fact, I remember a startup sequence where new data on a DMI interface update was followed by 'success'

  Then more waiting, a lot of the HD activity.

  Boot from CD/DVD
  DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER

  As a result, I put off the system and replaced the SATA cable (which I think is maybe defective), the computer started and entered correctly in Windows. No error logs or dump didn't report files, critical just an error in Event Viewer (Kernel-Power, event ID 41, task category 63).

  I ran sfc/scannow and it came back with the "Windows Resource Protection found corrupt files but was unable to solve some of them."

  System then invited to restart and it auto-couru chkdsk, a copy of the journal of wininit is attached, please see below.

  I ran sfc/scannow, once again, Windows Resource Protection not found any breach of integrity this time.

  At this point, I'm quite confused. I have no idea what causes these errors and cannot replicate force. I am sure that it is the RAM, but it was also suggested to me that the error is the CPU, the PSU or the same level of BIOS.

  FILES:

  Minidump

  report of BlueScreenView

  DriverView

  Information System

  Wininit

  MY SPECS:

  Type of PC: desktop
  OS: Windows 7 Ultimate SP1 x 64 (detail)
  Age about hardware: 3 years again
  The age of the BONES: one day (reinstalled on the new hard drive)

  CPU: AMD Phenom II X 4 955
  Motherboard: Gigabyte MA770T-UD3
  MSI R6950 Twin Frozr III video card
  Memory: 2 x 4 GB DDR3 1333 mhz RAM Corsair
  PSU: EZCool 550W JSP

  Hello

  Yes, all drivers that have been installed by myself is from the manufacturer's websites. It's a short list; they are

  Audio, Chipset and Gigabyte LAN (rev 3.1)

  AMD graphics

• Windows Mail can receive but not send up to exit application

  Hi and thanks for taking the time to read what I am in need of your help.

  I have a Toshiba P200, Vista Home Premium, Tiscali as my ISP, Norton Internet Security for AV and firewall and access my broadband via Ethernet to a Belkin ADSL router (and occasionally a Siemens router) and I am experiencing some strange events with Windows Mail.

  In short I can receive mail without any problems, but when I send the mail, remaining in the Outbox despite the option send immediately being checked, or by pressing the send/receive button. When I go out Windows Mail mail is sent immediately and is when I restart Windows Mail in the sent messages folder.

  So why I think there is a problem with the laptop. Well, I'm lucky to have a friend who has a non-Toshiba laptop, where all of the above can be replicated. Guess what, Windows Mail sends the message exactly as it should (on my account and on my network, through my router and the ISP, Tiscali etc.), so I conclude that the only difference is that my laptop is a P200.

  I called Tiscali, which confirmed that all my mail settings were OK, POP, SMTP etc, which I expect (because they work on the laptop from my friend), and they advised to contact Microsoft, I did, and since the P200 has pre-installed Vista they say that I need to contact Toshiba, and here I am.
  My P200 has been restored to factory settings, and I tried to get this working without Norton IS and no firewall (Vista and router) but no luck.

  Any ideas would be very appreciated and if I find through other means, I'll post back with the result. If the answer is already out there, please apologize for being too stupid to locate and beg your patience.

  Thank you very much.

  Hello

  It is typical for support persons. All of them are trying to refer clients and through them. In my opinion Microsoft s reaction is strange to me. They designed the operating system and they should be responsible for the feature.

  I have the Satellite A200 and Satellite P200D and I use Windows Mail on two of them successfully. My laptop is connected to the WIFI router and router directly to the phone line. To be honest, I have configured Windows Mail as you and all of the work are made in a few minutes.

  It is not easy to tell where the problem may be, but I think that there is a problem with some settings of your laptop. Some of them block it somehow. To compare your, with friends laptop is also not the best because it can have completely different OS settings (antivir application, the settings of the firewall).

  Try turning off all the features that can block Windows hotmail to see if there is some difference.

• 8620 OfficejetPro works with Windows 7 and 8 but NOT 8.1

  I bought a 8620 last week and it loaded well on our laptops to operate Windows 7 and Windows 8 and we are facing up and running and fully operational.

  However, while I followed the same process on our Windows 8.1 machine, and the printer seems to be properly installed, any impression that we seems to blend into the ether!

  I've uninstalled and reinstalled twice, made sure that the windows firewall is disabled (we have Mcafee) and generally tampered with about-, but to no avail.

  Does anyone have the solution please?

  Welcome to the Selpat forums!

  I understand that your Officejet 8620 does not work on your Windows 8.1 system, however, works very well with your Windows 8 and 7 systems. I would like to help!

  First of all, try to run the HP Print and Scan doctor.

  Please let me know the specific results of the execution of the tool.

  If the tool detects that the complete software is not installed, run the HP printer install wizard for Windows.

  Please let me know the result and how you have the 8.1 Windows connected to the printer. (USB, wireless, ethernet) Try an alternative connection as well to see if it will work.

  Happy Tuesday

• Why can I open windows in safe elsewhere but not normally?

  When I turn on computer normally don't start, if I put the safe way, he is open, but there are many things that I can't do.

  Hello

  1. What is the operating system installed on your computer?

  2. Since when are you facing this problem?

  3. don't you make changes to the computer before the show?

  4. you get any error message?

  Please follow the steps below.

  Method 1:

  Start the computer in safe mode and perform the clean boot.

  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

  NOTE: After completing the troubleshooting steps, please reset the computer to start as usual

  For windows 7 and windows vista

  http://support.Microsoft.com/kb/929135

  For windows XP

  http://support.Microsoft.com/kb/310353

  Please disconnect external devices attached to the computer and check if you are able to boot to the desktop.