Updating the DB via RMAN

Similar Questions

• Updated the BIOS via bootable USB drive

  I want to update the BIOS by using the ISO image provided. I want to write this image a usb, then on startup, the bios update. How to create bootable USB drive.

  My system is E430, although the question is pretty generic.

  Hi again, ahaider7

  I don't think that a program would be necessary. However, after doing more research, I'm not sure the work process. In addition, update the BIOS via USB is not supported, because as far as I know. If you want to update the BIOS of your machine, I highly recommend using the utility to update the BIOS. You can also burn the .iso to a CD and the image file.

  Kind regards

  Adam

• Update the BIOS via broken WinPlash SATEGO P100-10U. Now just black screen.

  Hello

  I did an upgrade of the Bios via WinPlash as I installed the XBox Live. Upgrading the Bios did not work (stupid me) and therefore, I'll have just a black screen after that I have turn on the monitor. The machine emits no beep, nor does it show anything else.
  I have subsequently:
  Downloaded the WinPlash on another PC. As it says in the doc (unziped in a folder), but the file '... ". for bootable CD"is not generated (nothing else that the files have been copied).
  Subsequently I have burned (all files = part of Vista 32 Bit) with NERO on a bootable CD, but it does not start the program (CD starts spinning, LED in CD / DVD flashes yellow then it stops).
  Then, I only copied their executables on a USB key, tired to load it from there - ZERO nothing but the sound of the screens black and fan.

  Tried to access the Bios with combinations of power sur-bouton ' "+ ESC, F1, F2, F10, F12, Del, ALT (as the left of the SPACE key), CTRL.

  Could someone tell me if there is a start-up tool or a BIOS image tha starts, or a special touch?

  Concerning
  Thomas

  Hello

  so, you have little chance really bad because this issue needs to be repaired by a qualified technician. I had a similar problem and have searched for a few weeks for a resolution quick and good cheap but I couldn t find anywhere these tools mentioned you´ve.

  Your only chance to bring the machine back to life is to contact a [ASP (certified partner) | http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/generic_content.jsp?service=EU&ID=ASP_SUPPORT]
  and allow them to correct this problem. I asked a lot of people here, but no one from toshiba is here to give some nice tools... :(

  Hope that your machine will come back to life.

  Welcome them

• BlackBerry Z10 can't open my Z10 BB after updating the software via wireless internet

  Please I need your support on my BB Z10 it stops working after that I updated the software of the world of BB and it stuck at 100% (finalize the configuration of the device), I did everything what I removed the battery and put it on again, I pushed the button reboot, I pushed on the volume buttons and the same result as I tried to get the new link BB software but the laptop can not read my BB and also my BB link, please see the photo below for more support and please give me support on this issue as soon as POSSIBLE.

  Hello and welcome to the community!

  Given what you describe, I recommend the very vigorous autoloader method to install an OS on your BB device. Something has gone wrong with the automatic method you used, and something more energetic (though not official) is required.

  Good luck and let us know!

• Cannot update the metadata via the API

  Is there something wrong with the simple ordinary call?

  curl-x PUT d ' data = {"version": "0.2.0"}' https://build.PhoneGap.com/API/v1/apps/234...0?auth_token=x...Y

  I want to just update the title and some version information in the application before the build... but even if I get a 200 and information, the version is not updated.

  Any ideas?

  Yes as said Kerri, meta-data need to be updated through the config.xml file. It looks that the docs indicate that the meta-data can be updated through the API settings, but this isn't the case. Ensure that the updated docs up-to-date.

• Automatically update the drivers via WSUS 3.0 SP1

  Posted November 16, 2010, 15:51

  Hello

  Recently at the company that I work we started pushing updates to the video card driver via WSUS. While users have no problems of installation, we had difficulty to automate the process. Basically, we have 7 computers that are run continuous tests that cannot be interrupted, except for 430 in the morning when they restart. We have a script that does the reset and we try to make these computers to install updates before restarting. I tried WuInstall, Remote X Reboot, this script:http://www.wsus.info...?showtopic=7298 and this: http://msdn.microsof...28VS.85%29.aspx where all work, ideal for installing Windows updates but none of them install updates of the driver as well! The updates appear as high priority and all other updates installed without problem, every single script/program that I use to try to automate the updates says "No update available" even if the Windows Update icon is still there. We tried this on Windows XP and Windows 7 computers and got the same result, we use WSUS SP1 on Server 2008. Any help/link to a program/script would be greatly appreciated.

  Thank you

  Please repost your request in the Forum of WSUS.  Thank you! Carey Frisch

• Update the driver Via Rhine II Fast Ethernet Adapter

  Help, please!

  I can update my Via Rhine II Fast Ethernet Adapter driver with the 3.84.0.1 64 bit version of Windows XP same dough I'm running a 32-bit Windows XP?

  I could not find a version to 32 bit Win XP.

  My current driver version is 3.32.0.417, and a few programs scan driver free, that I found on the Internet it were classified as 'old '. My Internet connection isn't going very well.

  My system information:

  Widows XP, home edition, service pack 3, version 2002, intel celeron 420 CPU @ 1.60 Ghz, 160 Ghz, 384 MB RAM

  Thank you very much and God bless you!

  Tiberiu, Romania

  # No, if it's only for XP - 64.

  A driver is 'old' does not mean that you need to replace.  The general rule for Windows drivers is, "if it ain't broke, don't fix it."  You should only update a driver if the device does not work correctly and you have reason to believe that the driver is at fault, or (b) the new pilot adds features that you want or need.

  OTOH, if you go to the real Web SITE (instead of random file download sites), you can find a driver for XP 64 and XP (i.e., XP-32) who seems to be newer than yours - version 3.87.  This driver is for the following models, which can be yours (you have failed to identify the specific model you have).

  Integrated VT8251, VT8231, VT8233, VT8235 & VT8237 integrated (Rhine & Rhine II), VT6103 Rhine (PHY), VT6105/L/LOM and VT6106/H/L/S series (Rhine III), VT6105M management Fast Ethernet Controller (Rhine III), VT6115 Fast Ethernet Controller (Rhine III), VT6107 Fast Ethernet Controller (Rhine & Rhine II)

• Failed to update the software via PC companion to Xperia X10i

  Hey,.

  I use Xperia X10i and currently I have version: 2.1.A.0.435 while an updated version: 3.0.1.G.0.75 is available.

  When I connect my phone to the PC companion for software update, it fails to prepare my computer and error message that could not update your software. My phone is slower and he needs software update, please help Sir to do.

  Thank you

  Make sure you have all backup

  Contacts

  just for play can we synchronize your contacts with google if you have not already

  Open your directory

  Press MENU-> Press Contacts send-> select all-> send it to your email address

  on your computer

  
  

  -> Download the file-> to your gmail-> contacts-click-> click on more actions-> on the drop-down menu, click "Import"-> choose the file-> and click Import

  SMS/MMS

  If you don't want to use the backup & restore app then

  Install "SMS backup" to back up your SMS and MMS to your Gmail account

  https://market.Android.com/details?ID=com.zegoggles.smssync&feature=search_result

  or your SMS usage

  «backup & restore SMS»

  https://market.Android.com/details?ID=com.riteshsahu.SMSBackupRestore&feature=search_result

  or for your MMS, use "save MMS".

  https://market.Android.com/details?ID=com.Schwimmer.Android.mmsextract&feature=search_result

  Call logs

  And this is great for call logs

  https://market.Android.com/details?ID=com.Yang.Android.ansta

  Apps

  Don't worry so much about backing up your applications

  on your computer, go to

  Market.Android.com-> log in-> click on my library-> and send all your apps on your phone

  

  My phone Explorer

  https://market.Android.com/details?ID=com.fjsoft.MyPhoneExplorer.client&hl=en

  If you have a lot of sms/mms backup & restoration will take forever or maybe not backthem up corectly

  the two apps over SMS backup + and backup & restore SMS are great, it is really fast

• DCC - cannot update the BIOS via command line settings

  I'm script an automated installation of Bitlocker on Windows 7 and 8.1 systems (company).  I use the last DCC and programs CCTK that came with it.  Systems have the latest BIOS updates, and are fully patched.

  I managed with several test systems (Win7, desktop computers, laptop computers (different models)).  I tried my scripts this morning on a laptop computer Win8.1 (Dell E6330) and as soon as my script runs to the addition of the password of the BIOS needed to make TPM changes ("cctk - setuppwd =" "") I get the following error:

  The required BIOS interfaces is not found on this system.

  I get the same error when running any other command CCTK used in my script:
  CCTK - tpm =-valsetuppwd =
  Activate CCTK - tpmactivation = - valsetuppwd =

  When I restart in the BIOS, no password has been set (all parameters are say no 'set') and the secure platform module is inactive.

  I updated to the latest BIOS (A14) and I get the above error message.  I know that orders CCTK I have scripted are correct, because they work on other systems.

  I wonder what could be the problem with this notebook and how I can come up with a solution.

  Thoughts?  Suggestions?

  Thank you!

  -Greg

  Just a quick update to let everyone know how I solved this:

  I had to install HAPI.

  On all other facilities that I have tested, just have the HAPI subfolder in the folder where CCTK. EXE was hosted was sufficient for work.  But for some reason some, in this case, once I installed HAPI and then ran my scripts again, they finished without a problem.

  I hope this helps someone else.  Seemed to be a solution simply absurd, but it is what it is.

• New W510, update the BIOS - black screen on startup - guaranteed?

  Hi all!

  I got a new W510 and decided to update the BIOS via the executable Windows 7 provided by Lenovo for their support-web. The program is run properly (all green checkmarks), the machine has been restarted and then stopped and started again - but she never stopped showing the "ThinkPad" screen POST. The machine started throwing his fans after some time and the machine felt hot enough it is up to the right. I waited a bit (say 4-5 minutes) if there was some additional BIOS update which took place, but nothing happened after a while, I decided to stop it. Now when I boot, the screen is all black.

  This will cover in the included warranty? It must be, right?

  Sorry for my late reply. As I think it is clear from my earlier post, there was still no way to load default BIOS that the screen went black as soon as I started the machine.

  Two days later from my first message I sent it in for repair. Almost 4 weeks after and TWO motheboards (first one was apparently DOA) later, the machine works now. As it seems, Lenovo had some problems for spare parts quickly enough because it took almost 2-3 weeks just to get the first map of mother (DOA).

  Anyway, even if it took some time, I can now enjoy my new machine

• Update the BIOS on a booted TS140 UEFI

  My TS140 boots Win7x64 UEFI mode. It's fast and quiet and beautiful. It is due for a BIOS update, although its present 99 for later, A8A.

  Instructions to update the BIOS via BACK to call for the creation of a BACK with Rufus bootable USB flash drive. The flash player is likely to be a legacy MBR bootable.

  Is there a risk of harm a system UEFI boot from and update the BIOS with a disk MBR-started? I have to undo, redo, or whatever it is reset after perform the update?

  Hello

  You should be able to update via the BACK without any problem and should not affect your BIOS settings.

• Update the Firmware Officejet 7310?

  Like my Officejet 7310 and recently took a used for children.

  The network shows Configuration Page printing "Firmware revision: RL7001xNx" on the unit used while my original unit shows "Firmware revision: RL9002xNx '"»

  Is there a way to update the Firmware of the unit used for the RL9002xNx version?

  I'm not finding a way to update the Firmware via the Sites from HP Support...

  Any suggestions?

  Thank you!

  My PC is always Windows XP SP3 but I added three laptop computers for the children and women who have Windows 7 and I had all the HP7310 installation problems or the center of HP solutions on their machines.  Make sure you get the Windows 7 "32 or 64 bit" depending on your system).

  My initial concern about requiring the update of the Firmware has actually been resolved, I think.

  Printer was running very slow and hesitant, I thought could have been due to Firmware.

  Found on another blog the suggestion to clean the sensor 'media' (red laser on the side of the cartridge carriage).  It worked and I'm very happy with the results!

• Impossible to attach Windows 10 laptop computer to the Internet via cable USB iPhone 5 c after update to iTunes and iPhone (March 2016)

  System information:

  Tactile Lenovo Y50-70

  Construction of 10.0.10586 of Windows 10-10586

  iPhone 5 c - iOS 9.2.1

  iTunes - 12.3.2.35 / 64-bit

  Cell carrier: Etisalat AF

  Last year in Afghanistan, I have used my iPhone 5 c to attach my laptop to the internet simply by connecting via USB.  It has always worked.  Was very simple.  When I returned to the States for R & R in November 2015, I've updated my iPhone and iTunes to the latest versions and upgrades Windows 8.1 to Windows 10.

  I am now back in Afghanistan and USB tethering no longer works.  WiFi tethering works half the time.  The other half of the time, when I try and connect to the network of the iPhone, it is said, you cannot connect to this network.  When I can't connect to the phone, I disable the personal hotspot, WiFi and Bluetooth on the phone and then I turn it back on.  I also turn off my WiFi adapter on my laptop and turn it back on.  Which usually solves the problem and then I can connect via WiFi.

  Do some research on the internet, I read that there was a file corrupted when the current generation of iTunes, but Apple had set and you just need to reinstall the current version, which I did.  I have reinstalled iTunes by suggestions from different site.  After reinstalling iTunes and restart, I can always have my phone to connect to internet via the USB cable.

  I want to be able to connect my laptop to the internet using my phone via the USB cable.  I want it all works just as it did previously.  Connection via WiFi is a pain in the ass, because it does not work half the time and disconnects on a regular basis.

  Please tell us what should I do to solve this problem.

  Thank you.

  OK, I finally understand how to solve this problem.

  I was able to understand because of this post:

  https://discussions.Apple.com/message/29267225#29267225

  The problem is that Windows 10 was not install appropriate drivers for my iPhone.

  You can see 2 places to see.  We're in the control panel.  After you plug in your iPhone, the iPhone will be displayed and highlighted as not having is not a compatible driver.  The other place is in "Devices and printers", there you will see 3 apple devices: 1 Apple Mobile Device USB Driver, iPhone 2, and 3. Apple iPhone.  All three appear when I plugged in my iPhone.

  However, the problem was one that said iPhone really should have said "Apple Mobile Device Ethernet".

  So, how to fix this?

  Open devices and printers-> right click Iphone which should be under "Unscpecified"-> properties-> hardware-> Propterties tab-> change settings-> tab driver-> update driver-> Browse my computer for software Local-> Browse to the directory "C:\Program Files\Common Apple Mobile Device Support".

  Make sure you have the files box to include under verified.

  Who did.  Windows successfully installed the necessary drivers.  Now, I can easily connect to the internet via the USB cable again without any problems.

• the process of updating jnlp is corrupting the cache via hotspot network

  Hi all

  This post is a Java cache problem. We have a jnlp file, responsible for the update of our application (so we cannot put 'offline'). The problem is that some of our users run the application behind a network of wireless access point. In this case, they do not have Internet access, but the java webstart mechanism tries to download the JNLP despite this. In this case, TJS downloads the HTML login page and put it in its cache without any verification. As a result, the next via shortcut access is impossible.

  Is this a known problem and is there a workaround?

  Thanks in advance for your answers

  FYI

  We removed the href of the tag of the jnlp file and it is now ok. The jnlp is never updated, but it's ok for us.

• Hanging in the updating of the IRR via Javascript

  Apex: 4.2.2.00.11

  I have an IRR that has a checkbox column. Checking the box either includes or excludes this specific row when the page is sent.

  I add a 'global' checkbox in the column header of the IRR report for this column. It controls, checks all the boxes in this column to SORT. Unchecking the contrary fact. The "global" checkbox is a toggle power switch of the checkboxes in the SORT.

  So far so good. Works as expected.

  However, during the updating of the IRR (due to changes of order sorting, additional filters added, etc.), it redraws the region of apexir_DATA_PANEL - and with it, he repaints the table headers too. And this removes the "global" checkbox in the column header. (a page refresh is necessary to return to the "global" checkbox)

  I want to do is add a function call to the Manager of refreshment of the IRR - the last call to the handler is the custom function that adds the "global" checkbox in the column header. Something like:

  . Bind $(«#IRR_OBJECT_HERE») ("onchange", function() {}
  AddGlobalToggle(); Added the check box of the column header if there is
  });

  I tried many references to object (unless the IRR) and managers of events, but without success.

  Is it possible to connect refresh report string of the IRR via Javascript?

  Billy

  Requires as not simply a dynamic action after Refresh on the IR region?