Upgrade camera 5.5.0 vcenter vCenter 6 database device error

Similar Questions

• How to upgrade the hardware on a VCenter Server

  In lab environment, two hosts, VCenter server, don't HA, storage etc. running share. I managed to upgrade hosts, using Crossover, but his declaration of errors when attempting to upgrade the hardware of server VCenter comments... I can see that it would be a problem, using VCenter to upgrade equipment on himself, when he needs to reboot the server to install. The question is, how to get around that? I tried to look for solutions, not found anything yet. Hope that makes sense.

  Latest versions of everything, as it is a laboratory under eval licenses. Thank you

  You must turn off the VM, connection to the ESXi host through vSphere client vCenter and right-click on the VM vCenter > virtual hardware upgrade.

  Make sure that you run VMware tools before do you.

• vCenter Server displays the error message: unable to connect to the host

  vCenter Server displays the error message: unable to connect to the host

  Symptoms

  • vCenter Server cannot connect to a host when you perform operations such as:

  •

  o Storage vMotion

  o cold migration

  o cloning a virtual machine

  o the model deployment

  • Newspapers vpxd that contains an entry similar to:

  [2009-06-04 19:27:16.326 error "App" 4444] [VpxdInvtHost] IP address change for 10.223.122.143 to 10.223.127.197 unhandled, verification of the SSL certificate is not enabled.

  • You see errors similar to:

  Unable to connect to the host o

  o [2009-06-04 19:27:09.952 'Libs' 3902384 WARNING] [NFC ERROR] NfcNewAuthdConnectionEx: unable to connect to peer (numRetries = 2). Error: Unable to connect to the host 10.223.122.143: connection timed out

  • vCenter Server shows the VMS as being disconnected then connected.

  Hello

  Resolution

  Cause

  This problem can occur if an ESX host's IP address is changed while being managed by vCenter Server.

  Check the cause

  To check the cause of the problem:

  1. Log in as root to the ESX host using a SSH client.
  1. In the file etc/opt/vmware/vpxa/vpxa.cfg, find the IP address of the host. The entry looks like:

     
     10.21.48.121
     

     Note: for more information about editing the files, see installation in VMware ESX configuration files (1017022).

  Troubleshooting

  If the IP address is incorrect, perform the following steps in order. If the operation does not resolve the problem, continue to the next step. Don't skip a step.

  1. Disconnect and then reconnect the host:
  1. Right click on the ESX host in vCenter Server and click Disconnect.
  1. Reconnect the ESX host in vCenter Server.
  1. Restart the VirtualCenter agent on the ESX host:
  1. Stop the service of vpxa with the command:

     # service vmware-vpxa stop

  1. Open the /etc/opt/vmware/vpxa/vpxa.cfg file in a text editor and correct the IP address of the ESX host.
  1. Start the service of vpxa with the command:

     # service vmware-vpxa start

     Note: for VMware ESXi, you may have to restart all the management agents. For more information, see restart the agents on an ESX or ESXi Server (1003490) management .

  1. Rebuild the VirtualCenter agent on the ESX host configuration file:

     Attention: this step removes all the Statistics counters historical host and the virtual machine. If VMware ESX host is running in virtual machines that starts in a permitted CVS environment, you maybe won't be able to add the host without stopping the virtual machines first.

  1. Right click on the ESX host in vCenter Server and click Disconnect.
  1. Remove the ESX host disconnected from vCenter Server.
  1. Backup the file vpxa.cfg with the command:

     # mv /etc/opt/vmware/vpxa/vpxa.cfg /etc/opt/vmware/vpxa/vpxa.oldcfg

  1. Add the ESX host disconnected to the server vCenter inventory.
  1. Run the following command to view the contents of /etc/opt/vmware/vpxa/vpxa.cfg and confirm that the host IP address is correct:

     # cat /etc/opt/vmware/vpxa/vpxa.cfg

• Replaced the SSL appliance - VMware vCenter Support Assistant device certificate

  Hello

  I need replace the certificate in the device wizard helps VMware vCenter but get the error below aa.

  
  

  Key file is empty, it does contain a private key or contained an unsupported key type. Supported key types are PCKS #1 and PKCS #8.

  
  

  However, the official documentation of the product on page 19 is 20 below the procedure.

  
  

  
  

  Replace your vCenter Support Assistant SSL certificate uses a self-signed certificate. You can change your SSL certificate in accordance with the policy of your company for SSL certificates. Procedure

  1 in a Web browser, go to the IP address of the device.

  2. connect the unit to Support Assistant vCenter.

  3 click the tab settings of VA.

  4 under the SSL Configuration, in the private key (.pem) text box, click on choose a file.

  5 in the file browser window, navigate to the directory that contains your certificate, select the private key (*.pem) that corresponds to the certificate chain and click Open.

  VMware, Inc. 19 if your private key is protected by a password in the password key text box, type the password.

  7 in the certificate (.pem, .p7b) string text box, click on choose a file to select your certificate chain file.

  8 in the file browser window, navigate to the directory that contains your certificate chain, select your Certificate SSL (*.pem, *.p7b) chain and click Open. NOTE If you try to add an expired certificate, a warning message indicates that you are not allowed to add the certificate.

  9. click on apply to apply the changes.

  Could someone help me.

  
  

  Hi, peaple.

  After several tries, I had success in the process of exchange of certificate VSA.

  1 - the DNS configuration was wrong.

  2 - certified should be the key (RSA private key format) published the .pem file must be trained using the service certificate + certificate of certification authorities.

• Export error records 'diagnosis package cannot be recovered from VMware vCenter Converter Standalone. "Error: could not generate file diagnosis of VMware vCenter Converter Standalone server.

  Hey, gentlemen!

  Trying to export logs from VMware vCenter Converter Standalone v 5.5.2 and this error occurs.

  "The package of diagnosis cannot be recovered from VMware vCenter Converter Standalone. "Error: could not generate file diagnosis of VMware vCenter Converter Standalone server.

  Can he save data to the file journal, but only coverter_gui newspapers, nothing else.

  Google search returns no results at all.

  What could be?

  OK, it is resolved after you restart the converter Services.

• Does vCO 5.1 comes with the vCenter 5.1 device?

  Does vCO 5.1 comes with the vCenter 5.1 device?  If not, how to set up?  Can gurus, you suggest a document or procedures?

  No it's not. Everything is explained here.

• VCenter Service database WARNING

  Hi all

  When I connect to my vCenter Server 5.0, I see warning about vCenter Service database. The message is

  Cumulative performance of statistics since the last week in the month is not involved in the database

  Cumulative statistics for the last month of the past year performance is not involved in the database

  Please your friend help, thanks before

  Hi, your work of performance statitistics rollup does not work.

  This KB should explain how to fix it:http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1004382

  And this post is my blog and explains how the rollup jobs and how statistitics is collected.

  http://vmice.WordPress.com/2012/03/05/VMware-vCenter-database-performance-statistics-explained/

  I hope this helps.

• The original driver of the camera again (which should be listed under portable devices) is missing

  I'm trying to get my Canon PowerShot A4000 IS to connect to my computer Dell Inspiron A537.  It has a Vista x 64 SP2 operating system.  When I plug the camera in I get a message that a device driver is required.   He research and can't find anything.   I contacted Canon.  They say that there should be a device driver built into Vista in the category of portable devices.  He isn't here.  I suspect that this was deleted when my daughter tried to connect his phone I some time ago.  How can I fix it?  I tried the program of Mr. Fixit in the support section.  Found problems, it could not fix them.

  All ideas

  Try this:

  Go to Device Manager and find the device that may be under 'Other devices', ' unknown devices "USB controllers" or "Hard drives" category. " It should have a yellow triangle with an exclamation mark. Right-click on it and click on "Update driver software..." The next box, click 'Browse my computer for driver software', then navigate to C:\WINDOWS\System32, click on the OK button and make sure the front box "include subfolders is selected', click 'Next' button and let windows install the driver.

• Aspire 4830 upgrade to win 10 of the 7 has failed with error C1900101 code, what is the solution?

  Said Acer laptop, aspire 4830 T is obsolete and cannot be upgraded to win 10 even if get win 10 app says its compatible with the upgrade. He said that some drivers or devices may not work with 10 victory. I tried to upgrade to win 10, but not successful and displays C1900101 error code. can someone help me upgrade to win 10?

  Your error code is listed here:

  http://answers.Microsoft.com/en-us/Insider/wiki/insider_wintp-insider_install/how-to-troubleshoot-common-Setup-and-stop-errors/324d5a5f-d658-456c-bb82-b1201f735683

• The upgrade of Windows will affect the following programs or devices I (need help)

  The upgrade of Windows will affect the following programs or devices:

  These devices may not work properly after the upgrade. Before the upgrade, we recommend that you update the drivers for those devices. Cancel the upgrade, open the control panel and search for "update device drivers" or go to the website of the manufacturer of the device to search for updated drivers.
  • • Keyboard filter

  I want to know how to uninstall it. And

  where I can get this update for the device.

  I have 1215ee DV6

  Product no. - NZ341EA

  Please provide the right solution.

  Launch Control Panel, in the section "Programs" click "Uninstall program. Select 'HP Quick Launch Buttons' in the list, and then click the uninstall

• File/import/Images of device / 'no camera or scanner not selected'... no device. Where is he? iMac El Capitan

  File/import/Images of device / 'no camera or scanner not selected'... no device. Where is he? iMac El Capitan

  Hi Tsavaruach,

  Could if it you please let me know the version of Lightroom that you are working on, also please make sure that Lightroom is to this day.

  Please update: keeping up-to-date for Lightroom

  Kind regards

  Tanuj

• upgrade from 5.1 to 6.0 vCenter fails with the error

  Hello together!

  We wanted to do an upgrade of vCenterServer 5.1 to 6.0.

  But we get an error after that I have to enter the vCenter Server credentials.

  It is the following error message:

  Error: IP address: xxx.xxx.xxx.xxx is present in the certificate subject names alt but under DNS key.

  This ip address cannot be used for installation.

  Resolution: use a dns name or ip address that is present in the subject of certificate alt names or regenerate the ssl certificate for the SSO before continuing.

  I don't know what to do.

  I think that Yes, that's what he meant.

  Quick question: have you checked with HCL before the upgrade?

  VMware Compatibility Guide: System search

• last upgrade vCenter device error

  Hi all!

  I'm trying to upgrade a vcenter 5.0.1 for 5.1.0 application. I use the oracle db

  If I followed the instructions (upgrade to VMware vCenter Server Appliance).

  When I choose "default sso config", I get an error 500 impossible to connect to the remote server: 10xxxxx

  If I don't use default values, I have to enter the DB connection. First test is with the db user sys to the dba.

  This resulted in an error "login as SYS should be as SYSDBA or SYSOPER.

  Then, the next thing: our dba has created a new user with sufficient privileges.

  Following error:

  [+ 2045] INFO | Database validation failed: BadTablespace - Tablespace RSA_DATA missing or not visible by the user.

  [+ 2048] INFO | Return code is: BadTablespace / 9

  [+ 2049] INFO | COMPLETED

  VC_CFG_RESULT = 720 (error: did not find the storage space required for the installation of the SSO.) Please, consult the installation and Configuration Manual on how to create spaces for storage.)

  It's not funny :-(

  Advice how to fix this?

  Thank you & see you soon

  Stefan

  On your oracle database, you will need to run these two files after appropriate change 'rsaIMSLiteOracleSetupTablespaces.sql' and 'rsaIMSLiteOracleSetupUsers.sql '.

  They are available on the iso image available for windows install under the single folder sign On\DBScripts\SSOServer\schema\oracle.

  I don't know if I'm allowed to join these files here in this forum.

  Concerning

  Girish

• Process of upgrading 3.5 host with vCenter server Virtual

  Hi I have recently updated my old server from client to vCenter 4.1 virtualized VI, sitting on my 3.5 cluster.  I intend to use the Update Manager to upgrade my guests, but I don't know how the virtual vCenter server is going to face?  The plan was: 1. move all the virtual machines off-host 1.  2 put the host in maintenance mode 1. 3. on the vCenter server, create a base, then line at host level 1 to 4.1. 4. now - at this point add this host in the cluster? And migrate the server vCenter top, so I can upgrade the other two hosts?  If the works above, then it should be quite a nice update, if you cannot add the new version of the host of back in, how you vMotion the vCenter server off so you can keep control of the cluster.

  IMO, it should work. To upgrade from 3.5 to 4.1, your ESX host must be in 5 update (see http://www.vmware.com/pdf/vsphere4/r41/vsp_41_upgrade_guide.pdf) already.

  If VMotion or migrate the server vCenter Server - for some reason-does not work, you can delete vCenter Server of the inventory of the old host and add to the inventory of the new host.

  André

• 4.1 upgrading of concern (32-bit vCenter) upgraded to 64 - bit

  Will start working 4.1 update soon in the laboratory.  My thought is that 4.0 is a 32-bit version of VC.  We installed on the OS, so need to create a 32-bit 64-bit DSN.  Someone has updated a vCenter 4.0, linked below on a 64-bit OS (2 k 8)?  I expect that the process of update 4.1 to deal with it effectively (IE, I create 64-bit DSN start upgrade and the upgrade process modifies an existing installation of 32-bit to 64-bit install?)  Any input appreciated.

  See VMware Documentation Upgrade Guide, specially the

  article 5 "upgrade to vCenter Server on a different Machine and upgrade

  existing data base":

  http://www.VMware.com/PDF/vSphere4/R41/vsp_41_upgrade_guide.PDF

  If you have found this information useful, please consider awarding points to 'Correct' or 'Useful'*.