Upgrade MCSA test

Similar Questions

• Satellite M40x won't start after upgrade CPU test

  I have a portable M40x I took the CPU out of it to replace it with another to test the computer started fine then I stopped and took out and put it's original return CPU, and it wouldn't start. Now it primer with any one of all the CPU. When I turn on the power, all I get is a white screen for a few seconds and the laptop is closed down. Both the CPU is good because I since tested on other computers to make sure that this was not the problem.

  Anyone has any ideas on what is the cause?

  I m not surprised.
  As far as I know, Toshiba does not support updates, and it is not advisable to do something like that.
  It of one that the replacement of CPU on laptops is not easy and not recommended.
  The processors used in laptops are connected to the motherboard using a process called TCP (tape carrier package). It is a method of permanent connection and is used in the interest of miniaturization and heat dissipation.

  He was awarded the new heat paste? It s necessary and important if you want to connect again the CPU.

  It is perhaps a reason for not starting.
  I think more details you will get from the service guy in your country

• Satellite 1410-303 - CPU upgrade options / tests

  Hello

  Sometimes I have a really rather old satellite S1410-303, which sports a * Celeron processor 1.5 ghz (256 k /400FSB). *

  As I have the latest Bios installed (v1.40 / 03 Sept), I'm curious to know if it would be possible to switch to a Celeron faster, released around this time. I am aware that the CPU should match some criteria, even 256 k of cache / FSB / Northwood arch etc and I was wondering if an update to a Celeron SL75T might work?

  The SL75T is a Celeron 2.5 ghz processor, it's a reasonable bump in speed. Sockets correspond to @478 / mPPGA too.
  The only thing maybe the draw the fate/energy are higher than the amounts

  Any thoughts?

  I am aware this Forum * an Italian guy tried putting a pentium 4 base FSB CPU @400 2.0 ghz in the same laptop computer and it didn't work *. So it seems Celeron only, probably 128 / 256 k cache according to.

  Anyone have a list of definitive of what the BIOS v1.40 supports?

  Thank you, john

  Eh, it's very old piece of hardware, and it is not easy to pick up some info on this.
  What I found is the info the 1410 has been delivered with different processors Mobile Intel Celeron:
  1.6 GHz (1.45volts)
  1.7 GHz (1.45volts)
  1.8 GHz (1.45volts)

  Then maybe you can check if you can find a faster clocked at 1.8 GHz and update.

  Sorry, but everything what s that I can write about it.

• Blue screen on my Qosmio F20 upgraded to Vista

  My F20-137 that "Windows Vista Upgrade Advisor" test but "Blue screen" error occurred at the end of the upgrade process so that the upgrade was able to complete. Windows says it is a problem caused by some device driver, but I got the whole system before the upgrade (no third-party drivers in the system).
  Could someone help, please?

  Hello Steve

  I know that you and many other users interested in this new operating system. As you know Toshiba is not officially on the market and there is no official driver to find.

  Check if you can find some vista forum. I'm sure that you'll find more info and discussion on vista.

• Satellite A210 - 17 X-PSAFGE 03600LFR - HARD drive upgrade

  Hello

  Someone would be able to help me in upgrading my computer portable HARD drive?

  When looking on the Toshiba support, can't get a reference to the HARD drive.

  Looking around on the net, I found a few 500 GB for example:
  -Western Digital WD5000BPVT WD Blue Mobile HDD internal 2.5 "SATA II 5400 RPM 500 GB
  -Western Digital WD Scorpio 500 GB 16 MB 7200 RPM black, WD5000BPKT

  Two of these SATA2 HDD would work in my laptop?

  Or shall I seek another Ref.?

  Thanks in advance

  Eric

  I think you can use both of them. I just hope that all capacity 500 GB is recognized correctly.
  After upgrade, please test and send feedback.

• What is the best to take now MCITP SA 2008 or 2012 MCSA

  Hello world
  I take the CCNA exam next month, and then I intend to take a Microsoft only Certificate not sure one is
  I have 3 options:
  1. take mcsa Server 2012 which has 3 reviews
  2. take mctip server administrator who has 3 reviews but will be retired in July 2013 and they will change his name mcsa ws 2008
  3 take mctip Server mcsa (2008) - option 2 - then upgrade and take a review of upgrade mcsa 2012 afterwards.
  I was advised by a friend to go for option 3 because if I take option 1 I couldn't find many employers looking for mcsa 2012 and he said 2008 is number one on the market today.
  Someone else recommend take directly, he said, it's the best option I can do server MCSE straight infrastructure 2012 then passing only 2 exams mcsa 2012 (option 2).
  Please help me I'm really confused.

  Hello

  can you please suggest me one will be paste MCITP / MCSA 2012?

  how the two will be valid?

  Contact http://social.microsoft.com/Forums/en-US/home?forum=certgeneral

• Windows 7 security upgrade failed

  Improving security required to stop repeated Internet Explorer 8 crashes.  Tried the upgrade with Trend Internet Security also disabled.

  * original title - failure (7 items) ___Windows 7 (32-bit) security upgrade-many tests have failed.*

  An update of security should not prevent Internet Explorer crashing, what a security update is likely to do, is to prevent malicious code to exploit a problem in the browser. If Internet Explorer does not respond, it could be corrupted add on.

  Click Start, type: Internet Options
  Press enter
  Select the "Advanced" tab
  Under reset Internet Explorer settings, click "reset".

  This should restore the Internet Explorer default settings. Releasing it's easy: with Windows | ActiveWin | Laptops | Microsoft MVP

• CUCM Upgrades vMotion of call center 24/7 production cluster (multiple) laboratory

  Hey everybody,

  I'm looking for documents that would support a Production Call Manager Cluster upgrade is done in the laboratory.  We did this for cuic, where we clone the Production VM and vMotion for a different Blade (dead net) and make the upgrades during the day, because there is no impact, then vMotion, their return to Production during a window of failure and turn them up after the turn down of the current production those.

  A couple of our clusters with 24/7 call centers, we wanted to limit the amount of time, they do not have some services, such as the mobility of the Extension. It is something that I have recommended, but I need of documentation or even a case of TAC for support to demonstrate management, since it is very different from our current MOP to make the upgrades.

  Thank you

  Randy

  The only caveats that is there is listed in this document only if you click on the hyperlink of VMware vMotion. If you follow them, then there is of course no problem, however you can always open a proactive TAC folder and get this done under their supervision/management, as long as you have a contract of ISV1 which I think is important to VMWare support not bound.

  If you have any doubts and want to go a way the recommended and most reliable compared to the then simply do vMotion using the DRS mechanism which is Cisco preferred for such things. Simply make a backup of DRS of your existing CM clusters running in production, create virtual machines using the same details such as the IP address, host name, NTP etc in his laboratory on a secluded environment and complete the restore of the DRS then and do what you want on the upgrade plan , etc.leaving tests the intact production servers. Once you upgrade and test had been made successfully in the laboratory, simply choose a Cup date more bring the server down production and move from laboratory to production.

  Concerning

  Deepak

• The upgrade to 8.54 tools user interface fluid of hcm 9.2 8.53.03

  Hello

  We intend to upgrade our tools to 8.54 version in order to view the capabilities of fluid. We actually completed the upgrade of the tools (test instance), but later realized it takes also minimum image PUM 8 or greater?

  Is this correct? Because after our upgrade of test was not the fluid related whitelists / etc in the upgraded instance roles.

  Kind regards

  Alok

  Hi Alok,

  By improving the tool to 8.54, you will be able to develop a new fluid user interface definitions, but you can use fluid UI comes with application of HCM.

  This, to be on HCM PI9 image. For more understanding of the fluid UI on HCM visit the webcast below.

  https://support.Oracle.com/RS?type=doc&ID=1952956.1

  Kind regards

  Shashank

• upgrade to version 10 of the vm or stay at 8

  Hi all

  I have just upgrade our test to esxi with vcenter 5.5 5.5 environment, and I was wondering if it is a smart choice for updating our vm vm version 10 or leave them at 8?

  the only because I read attributed words that you can only manage virtual machines via the web client that isn't really a problem, since we have also installed. It is more that we are accustomed to the c# client and web client, things are in a different place.

  But on the other hand, we do not expect to use the new features in version 10 of vm as vGPU or other things.

  It's just from the point of view of the administrator, we have always upgraded the VM for the latest version of the material in the past.

  copy of a ko: VMware KB: upgrade to the latest version of material (several versions) of a virtual machine

  VMware recommends that you upgrade virtual hardware to the latest version available.

  ESXi/ESX version	Virtual hardware version
  5.5 ESXi	10
  5.1 ESXi	9
  ESXi 5.0	8
  ESXi/ESX 4.1	7
  ESXi/ESX 4.0	4

• FMW: Portal Upgrade Advisor - review of videos on "how to install Oracle Middleware 11 g Rel 1 portal and explorers.

  Configuration - upgrade the test system - 'build base Middleware of Oracle 11g Architecture'
  Review of the videos for "How to install Oracle 11g Rel 1 portal Middleware and discoverer?"

  Part 3 installation of the basic Oracle Home (10:40)
  https://support.Oracle.com/CSP/main/article?cmd=show & type = ATT & ID = 1118681.1:PD11G_INSTALL_PT3 & inline = 1

  RE: NOTES: so it seems that do us step 4 [update software/binary in the ORACLE_HOMEs] here
  instead of step 3 [install but do not configure Oracle Identity Management] starting from
  'Build base Middleware of Oracle 11g Architecture'.
  Maybe suggest to change the documentation in MOS Advisor upgrade,
  to remove step 3 until after the upgrade the binaries and install patches 11g group.
  Or change this 3/4 part to talk to install IDM.

  
  Part 4 patch the Oracle home (04:57)
  https://support.Oracle.com/CSP/main/article?cmd=show & type = ATT & ID = 1118681.1:PD11G_INSTALL_PT4 & inline = 1

  RE: NOTE: it looks like a typo/read error on the page that says "necessary to run the Wizard Patch (PSA) Set?"
  There, it says '... If the Group of hotfixes version UCR has been used, no action is required. "I think that it should
  say «...» If the Group of hotfixes RCU version was NOT used, no action is required. »

  
  

  Part 5 running the Configuration Wizard (08:50)
  https://support.Oracle.com/CSP/main/article?cmd=show & type = ATT & ID = 1118681.1:PD11G_INSTALL_PT5 & inline = 1

  Specify the Application FOR page/section: you must specify OID information for installation of the portal.
  If you do not wish to integrate oracle descoverer services and do not want single sign - on, uncheck the box.
  RE: NOTICE: verbal instructions on this boy, are confused.    Instructions on where to get information from the OID would be useful
  here. in addition, the instructions show that if you have specified use of discoverer, a check box is displayed and check
  That's if you want to use the SSO on.   A blurb on what if you did NOT specify discoverer would be appropriate here.
  Or something about this discoverer is and if it comes by default with the installation.

  First, as discussed in another thread, I plan to reformulate the wording of this step... so thanks again for your comments.

  Note on this question / comment

  "To understand at the time where we upgrade repository portal.  In my opinion, who runs the configuration wizard PFRD is that fact for us.  I will go through the video.    And me who runs the IDM upgrades OID configuration wizard. »

  PFRD Configuration Wizard does not upgrades the repository of the portal, it creates just a portal 11g AS Instance against the repository Portal 10g's existing. The Upgrade Wizard upgrades site two-step

  1 put Update Wizard (option "upgrade intermediate level Instance") upgrades 11 g base instance configuration so that it matches the source portal AS10g instance configuration

  2 Upgrade Wizard (option "Upgrade the repository in metadata schemas") upgrades the repository Portal 10 g.

  It's a similar story for instant messaging, only the IM Upgrade Wizard upgrades the configuration file system and the GI database schemas in a go (IE there is no upgrade wizard option separated to "Upgrade the repository in metadata schemas")

  I think that the Viewlet created the PFRD and IDM Upgrade Guides whether clear.

• ORA-942 from the page of connection details of OEM 12 c installation during 2-system upgrade database

  Hello

  I am trying to improve our 11.1.0.1 to 12.1.0.3 OEM production using the method 2-system.  When I try to keep in the database connection Details page after you have specified the connection details for the copy of the deposit on the new host, this error pops up:

  ERROR: ORA-00942: table or view does not exist

  Unable to connect to the database and validate is a database supported due to one of the following reasons:

  (1) credentials incorrect

  (2) the auditor may be out of service

  (3) database is perhaps out of service.

  Check the credentials, the status of the listener and the database, and then try again.

  This error is not moved when we used the same procedure to upgrade a test installation 11.1.0.1.  In addition, I tried to change the connection details to connect to the repository of original production and got the same error.  This seems to indicate that the problem is specific to this repository.

  I'm Tournai on sql trace for another chance and found this error in the trace file:

  The following statement has encountered an error during the analysis:

  "Select count (1) in the mgmt_targets where target_type = 'host' and target_name ='oem12c.gfcsap.com"

  Encountered error: ORA-00942

  This error is meaningless to me that mgmt_targets is present in the sysman schema.

  Any suggestions on how to move beyond this would be appreciated.

  Dave

  Hi all

  While explaining the issue to a colleague, it dawned on me that I had not thought sys could be running the query instead of sysman, in which case a synonym would be necessary.  I checked the test repository, and it had a public synonym for sysman.mgmt_targets.  The production repository was missing the synonym.  After you create the synonym in the repository of the production, I passed this stage.

  Dave

• Connect the 7 error after upgrade to link 9

  I just upgraded my test environment to 9 connect successfully, but when I connect I get an error from Adobe Acrobat Connect 7 Profesional. I don't have this when we were on Connect 8. Here is the error message in its entirety

  Adobe Acrobat Connect Professional 7

  error internal error title

  body-error-internal error

  Details of the request:
  ============================
  < mode action "multiple" = >
  < name of the action = "report-my-meetings" >
  < param name = "tri-date-begin" > desc < / param >
  < param name = "filter-expiré" / >
  < param name = 'include-user-count' > false < / param >
  < param name = "filter-type-name" / >
  < order by name = "tri-date-begin" / >
  < order of orientation = "descendant" / >
  < / action >
  < / action > +.

  
  Details of the response:
  ============================
  < results >
  < status code = "some errors" / >
  < result >
  < status code = 'ok' / >
  < sco - nav >
  < sco sco - id = "470507" type = "tree" icon = "folder" depth = "0" >
  < name > training catalog < / name >
  < / sco >
  < / sco - nav >
  < / result >
  < result >
  < code of State = "internal error" >
  incorrect syntax near 'b' < exception > [Macromedia] [SQLServer JDBC Driver] [SQL Server]. < / exception >
  < / status >
  < / result >
  < / results > +.

  Any ideas as to what could be causing this?

  I contacted Adobe support for help with this issue and I would like to add that we have done to solve this problem of thought incase everything else has a similar problem. The main problems have been resolved when we learned that I did not change the compatibility level of the database when I copied the database to a new server. Once this was changed form SQL 2000 to SQL2008 issues went away. I think that Adobe Connect 9 requires that the database or a SQL 2008 database or later version.

  Right-click on the database and select Properties

  Go to Options and change the level of Compatitbilty to SQL Server 2008 (100)

  Hope this helps

• request upgrade from esx3.5 u4 to vsphere

  Hai

  I have sucessfully upgraded my test server with 1.5 TB of LUNs from esx3.5 to esx4.0, now I want to do to my site of production company there 4 host ESX 3.5 and 28 live servers.

  precautions, I don't have to the improved test improved vcentre and

  (1) stop the virtual machines

  (2) esx moved into maintenance mode

  (3) installation of the update hosted started noted that esx 4dvd iso image and updated successfully

  (4) improved vmtools

  (5) virutl hardware upgrade

  now, I'm going for my production site

  Here are the General steps that I followed, but my production cluster has 28 vms in common 2 TB lun

  In addition to the closure of vms, what should I do for the lun, should I leave the lun connected to esx during upgrade (before I left it as it is) and upgraded successfully, but it's my direct environment and I don't want to

  have any disaster

  all tips are welcome

  VAMSi

  Hello vamsi,

  You do a uprgade. You will lose all of the settings.

  Recognize your LUN will subsided.

  Puts goede groeten

  Davy Vermeir

  Network engineer

  Dir. phone: + 32 (0) 3 451 32 39

  Aurelium, people benefiting from ICTS

• Upgrade of the spatial and multimedia of invalid question components

  Is it safe to remove space 11.1.0.7 and multimedia Oracle? As we don't use it as indicated below by the exit. How can I uninstall space and multimedia Oracle?
  
  I have a lot of mistakes of classes in java for two components during the upgrade to 11.2.0.1 so I decided to drop / uninstall and do the upgrade, I can do?
  
  SQL > /.
  
  NAME TOTAL_SAMPLES CURRENTLY_USED FIRST_USAGE_DATE LAST_USAGE_DATE LAST_SAMPLE_DATE DETECTED_USAGES
  
  --------------------------------------------------------------------------------
  ---------------
  --------------------------------------------------------------------------------
  --------------------
  --------------------------------------------------------------------------------
  --------------------
  --------------------------------------------------------------------------------
  Oracle multimedia 0 70 FALSE 12 January 11
  Space 70 0 FALSE 12 January 11
  
  Thank you

  If you do not have these components, why remove them? :-)

  If you insist on installing them off, then clone your current database on a test server, perform uninstall the test database, then upgrade the test database to ensure there is no problem.

  Good luck!

  Srini