Upgrade path to 260 MB computer operating systrem

Similar Questions

• Impossible to reinstall XP, error «...» Windows is not a supported upgrade path"

  Computer is 2001 Sony Vaio apparently infected Office who knows what, if I want to do a clean install of the operating system. The computer came with Windows ME and a drive to upgrade to XP. 5 years, a technician thought he was doing me a favor and installed without my knowledge its own XP Pro.

  I tried to do an installation of my upgrade XP disc but I get this message: Setup is impossible to pass your current installation of Windows XP. Your current Windows installation is not a supported upgrade path. Setup cannot continue.

  I also tried to use the Sony system recovery CD, but it does not work.

  Help!

  Hi IAMSOBZ,

  As you install the operating system from a CD to upgrade it you will be asked for support of qualification, you can insert your Windows Millennium Edition or any CD which is an edition less than Windows XP Professional.

  Important: You will need to have a CD of Windows 98/Me/2000 eligible to insert if you are using a version update of XP to clean install. OEM restore disks will not usually fill the eligibility standard. If the restore disc i386 folder, it will work normally.

  a. start your computer from the Windows XP CD-ROM. To do this, insert the Windows XP CD into your CD or DVD and then reboot your computer.

   

  Note: To boot from the Windows XP CD, your computer BIOS settings must be configured to do this.

  b. When you see the message "Press any key to boot from CD", press any key to start the computer from the Windows XP CD.

  c. once the Welcome to Setup screen, press ENTER to start Windows XP Setup.

  d. read the Microsoft software license agreement and press F8.

  e. Setup will scan for previous Windows installations

  f. you will need to replace the CD of XP with your qualifying CD; XP Setup will scan the qualifying CD and ask you to replace it with the XP CD to continue installing XP.

  g. complete the installation

  You can refer the link to find out how to install Windows XP below: how to install or upgrade to Windows XP: http://support.microsoft.com/kb/978307

  With regard to:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Find the product number for the vista on the computer operating system?

  Find the product number for the vista on the computer operating system? I want to upgrade to Windows 7 and do not habve the product number

  OT:

  RPF Vista product number

  IF you need to find your retail business (NOT OEM preinstalled HP, Acer, etc..) Product key Vista, use these programs.

  No product key you will find for OS OEM preinstalled by this method is only used at the factory for multiple installations and of no use to you.

  http://www.Belarc.com/free_download.html

  https://www.magicaljellybean.com/KeyFinder/

  @@@@@@@@@@@@@@@@@@@@@@@@@@

  If you need to reinstall your Vista preinstalled, use this product key.

  The COA sticker is either or in the battery compartment on the underside of the laptop.

  With a desktop computer, it's on the side, the back or the top of the computer case.

  

  See you soon.

• 13.2.2 to 14.5.0 TMS upgrade path

  Hello

  I'm looking to make an upgrade to TMS 13.2.2 we currently have running on an old box of Windows 2003 R2.

  We are looking to set up a new server using 2012 R2 as the operating system.

  The environment:

  Windows 2003 R2

  SQL Express 2005 w/DB hosted locally

  13.2.2 TMS

  TMSXE (on another server) 3.0.2

  The methodology of Migration:

  Migrate the existing database to a SQL server hosted and test all the features

  If it is successful then

  • Remove the old server from domain/network
  • Rename the new server the same as
  • Install the TMS 14.3.0 on the new connection to the existing database server, hosted on the external SQL Server
  • Run the time zone update tool that comes in 14.3.0
  • Update the 14.3.0 existing install 14.5.0

  This methodology seems as if it was the right way to go? There are fundamental flaws, that I don't see here?

  I did this upgrade path in the laboratory successfully using a copy of our existing database, I have no alternative endpoints or vcs-control etc. to connect to the lab to prove everything works after upgrade.

  I look forward to your responses.

  Thank you

  Alex

  Hello Alex.

  You should consider upgrading to TMS 14.6, which is the most recent version.  14.6 TMS notes.

  TMS 14.5 supports only Windows Server 2012, not 2012 R2, but 14.6 done TMS.  Also, if you are not already the case, consider using SQL Server 2012 or 2008 R2 64 bit, to be compatible with future versions of TMS.

  The steps that you listed sounds good, just check on that TMS installation guides for supported versions of WIndows and SQL details, as well as all the required components.

• The following problems prevent upgrade Windows. Cancel the upgrade, perform each task and then restart the upgrade to continue. To upgrade to Windows 7, the computer must be running Windows Vista with Service Pack 1 (SP1) or later.

  I get this message when you try to upgrade to 7!  My computer is 100% in windows update update - please help!

  Hello

  What happens when you try to install SP1/SP2.

  Read through the material in the article...

  http://Windows.Microsoft.com/en-us/Windows-Vista/learn-how-to-install-Windows-Vista-Service-Pack-1-SP1

  Notify us of any errors when you try to install the service pack.

  To know if SP1 is already installed

  • Click the button start , right click on computer and then click Properties.

    Check if Service Pack 1 is listed in the Windows edition section.

    Cheeeers...

    Erwin

• Upgrade XP to Windows 7, computer recognizes not all files on drive E:

  Buy Windows 7 Professional Upgrade from amazon.com. Computer XP, does not recognize the DVD when inserted. I think that the E: drive is CD/RW, not DVD. No hope or help?

  Hello

  1 how many optical drives you have connected to the computer? What is the brand and model of these readers?
  2. are you able to read any CD?
  3. this happens with some special DVD?
  4. have you tried the same DVD on another computer?

  We need more specific information to help you better. Also remember that CD players will not read or write any DVD.

• What is the cost of upgrade from Vista to a decent operating system?

  What is the cost of upgrade from Vista to a DECENT operating system

  What is the cost of upgrade from Vista to a DECENT operating system

  Before you start shopping for Windows 7, make sure that your Vista is capable of running Windows 7.

  To learn, you must run Windows 7 Upgarde Advisr:
  http://Windows.Microsoft.com/en-us/Windows/downloads/Upgrade-Advisor

  To choose which version of Windows 7 depends on what you need or wait for Win 7. It's pretty subjective.

  Here is the list of the versions of Windows 7...

  The link below gives you a brief description of each version of Win 7.
  http://www.windows7news.com/Windows-7-FAQ/Windows-7-Starter/

  As if that wasn't enough, you have also the choice of 32-bit or 64-bit.
  Please read this topic vs 32-bit 64-bit

  http://www.w7forums.com/Windows-7-64-bit-vs-32-bit-t484.html

  Windows 7 price comparison:
  http://Windows.Microsoft.com/en-us/Windows7/products/compare

  Without knowing what you want to window 7, I would venture to recommend Windows 7 Home Premium.

  Question:
  What version of Vista you have now?

• IDRAC6 upgrade path

  I am temporarily caring for a Dell PowerEdge T610 purchased in 2012.  Our outsourced IT Department walked me through some maintenance tasks, including required launches a Virtual Console through iDRAC6. Apparently my iDRAC6 version (V1.80) is so old, no modern browser it supports fully. What I have for the most part works with Chrome and FireFox, not IE (but it's OK - I don't work with IE either).

  I am trying to determine if a firmware upgrade path exists for my hardware, and if so, what are the steps. None of my research on the Dell Web site have meaningful results. Since my system is no longer under warranty I don't get a lot of help by telephone, and "cat" is denied for me as well.

  If anyone can point me to a good place to get started which would be a great help.  Thank you!

  Hello.

  See the upgrade below. First apply the BIOS, then the respective DRAC6 firmware.

  6.2.3 BIOS iDRAC6 v1.92                   

  BIOS 6.3.0 iDRAC6 v1.95                  

  BIOS 6.4.0 iDRAC6 v1.97, iDRAC6 v1.99 , and iDRAC6 v2.8.0                  

  The path of update will prevent iDRAC communication and other server issues.

• Upgrade path 5500 series ASA-SSM-10

  Can anyone provide the proper for the 5500 series ASA-SSM-10 upgrade path of

  6.0 (5) E2

  TO

  7.1 (10) E4

  The release notes state that you must run just least 6,0000 e4 could so I just spend 6,0000 E4 5,0000 E2 then directly to 7.1 (10) E4?

  Also, the SSM-10 is able to effectively run the 7.1 (10) E4?

  Hello

  Yes, you can directly upgrade 6.0.5E2 to 6.0.6 E4 and then directly to version 7.1. (10) E4. After the upgrade for the latter, you might even go to latest available patch as well.

  -Yes, SSM1 - is able to effectively execute the 7.1.0E4.

  Kind regards

  Akshay Rouanet

• ACS 5.1 upgrade path

  Hello

  I have just unpacked ACS1121 with 5.1.0.44... Version of the ACS software. Y at - it (upgrade path) proceedings at this level to a version 5.2.x (later

  5-2-0-26-5)?

  You use a repository of tftp. If so try with a ftp repository

• Windows computer operating system Maintenace scam"with the accented India operator?

  What can be done to prevent calls from scam to the India that are discussed in the stream on 'Windows computer operating system Maintenace' scam?  I used recently both my computer and my tablet on a public network, once google alerted me that someone in Dallas was trying to connect with my log in. They tried several times.  I will not be on public networks once again.  I have change all protocols, then the India phone calls began.  It is the third attempt.  Is there some sort of cyber police force where we can report the problem? I have not run any of the controls suggested.
  Thank you for taking the time to answer.
  R2jmm

  Hi R2jmm,

  Welcome to the Microsoft community.

  It seems that you have received a call from the scam to a person who claims to be from Microsoft India.

  If you have not opened an incident (support ticket) with Microsoft, they do not contact you.

  Check out these links for more information:

  http://www.Microsoft.com/security/online-privacy/phishing-scams.aspx

  http://www.Microsoft.com/security/online-privacy/msName.aspx

  It will be useful.

  Let us know if you need help on Windows in the future. We will be happy to help you.

• C / SX / EX / MX upgrade paths

  Hello

  I have been the scene of c20 upgrades via the GUI and CPC, 4.x > 5.1.1 > > 7.3.2 7.1.1 hopping. 3rd party support told me that this is the way to upgrade the C20s.

  I struggled to find any documentation to confirm this upgrade path to 7.3.2. I'm about to proceed to the upgrade C40s and 60 with SX / EX / models MX.

  I'm looking for the validation of the document confirm how best to spend to 7.3.2 on all of the above models.

  I looked at the release notes do not seem to talk about any version of jump requirement.

  Thank you

  B

  You can go directly to the current version of the TC software without having to jump several releases to get there.  You'll just need to get the keys to unlocking the Cisco Licensing Portal TC7.x and apply it on the codecs, before doing the upgrade.  Applying the unlock key invites you to restart, you can disregard and go directly to download TC as the upgrade to restart anyway endpoint and apply the release key at the same time.

  Note, it is important that you read well ALL the TC release notes for the current version, you have up to TC7.  There are several versions where changes have been made that could be important to you.  Some of these changes are:

  • TC5.x - required serial connection is by default enabled (important only if you use control 3rd party such as Crestron or AMX systems)
  • TC6.x - layouts have changed, especially when using two screens with presentation and selfview.
  • TC7.x - Root access has been removed (I noticed that mention you SCP that requires root access), also instantaneous behavior has changed over the previous day.

• vCD 8 upgrade path

  Hi all

  Can upgrade you form vCD 5.5 directly to vCD8.0 or are you to go first to 5.6.4?  I can't find anything in the notes version or installation & Upgrade guide.

  Dave

  OK - I answered my own question with the Matrices of the interoperability of VMware products.  I don't know if the "Upgrade Path" option is new, but I don't remember having seen it before.  In any case, the vCD 8.0 upgrade is supported from version 5.5.4 and 5.6.4.

  Dave

• just bought a new EOS 7 d mk2 camera but can't open the CR2 raw files in Photoshop CS5. I downloaded the new raw converter for the camera which is the DNG 8.7 format for my windows computer operated. When I click on a CR2 file I get a subventio

  I just bought a new EOS 7 d mk2 camera but can't open the CR2 raw files in Photoshop CS5. I downloaded the new raw converter for the camera which is the DNG 8.7 format for my windows computer operated. When I click on a CR2 file I get a notification to come as States "could not complete your request because the file appears to be a model of camera that is not supported by the installed version of camera raw.

  I'm entered in Photoshop and loaded the dates above, but have met 3 mistakes when you do this (1) Adobe Bridge CS5 4.0.5 (2) Adobe extension Manager SC5 5.0 update (3) 12.0.4 for Photoshop CS5 Photoshop

  I tried for 2 days now to try to get the operating system for your support/help will be most appreciated.

  My old camar is an EOS20 D and I have no problem with CR2 files it produce

  Hi rodaks, george

  Images II 7 d would be directly supported in Photoshop CS5 as requiring a new camera raw.

  So, you must download the free DNG Converter to convert these images to DNG and then open the DNG converted in Photoshop.

  See this link for download DNG Converter 9.0:

  For Mac: Adobe - Adobe Camera Raw and DNG Converter: for Macintosh: Adobe DNG Converter 9.0: thanks

  For Windows: Adobe - Adobe Camera Raw and DNG Converter: for Windows: Adobe DNG Converter 9.0: thanks

• I bought Lightroom 5 of B & H Photo a few months ago and since then have now upgraded computers. This new computer doesn't have a hard drive and I can't figure out how to download it on my new computer. I must not have created an Adobe account when I

  I bought Lightroom 5 of B & H Photo a few months ago and since then have now upgraded computers. This new computer doesn't have a hard drive and I can't figure out how to download it on my new computer. I must not have created an Adobe account when I initially purchased and downloaded on my other computer. How can I still download it if the serial number does not appear in my plans and products page? I still have the drive and everything that came with it.

  Hello

  Please download the Lightroom 5 application from the link below.

  http://prodesigntools.com/Lightroom-5-DDL-comparison-vs-LR4.html

  Serial number - please visit https://helpx.adobe.com/x-productkb/global/find-your-serial-number.html

  Let us know if this helps!

  Kind regards

  Vivet