UPnP EA6900 problem

Similar Questions

• Beach ea6900 problem

  so I'm facing the same problem with 2 devices, when I bought the first linksys ive contacted then they offered me a device replacement which is the second, although he has the same problem which is low-end, I optimized the wireless settings for the best, is it possible, and always the same, tried also to reflash it has not changed anything , he reached a 20 ft and it's, it's impossible that a very old cisco x 3000 has a range higher than that ive done all the troubleshooting steps a linksys but online

  did not work as I tried to test the rssi, noise in my house that was really low voice against zero tested interference e3500 at the same place and the same power cable and is much better than the ea6900 what to do! thogh I do not complain about speed. also his

  overheating a lot! even with the first!

  I have the ea6900 and access the wifi 2.4 from my neighbors across the street home. It is therefore capable of long range. You mention that you used the same power cable to test both? Make sure that the supply cable is correct because the older router may not provide enough amps to fully power the ea6900. You may also have a setting that is causing your problem. Try a factory reset and see if it helps. Do not restore your settings from a backup, but just try to see if it is better before making any changes after the reset. Make sure the antennas are on tightly. They should not move easily when shaken, but not to overtighten the. I have mine with external antennas on a 45 degree angle and the Middle upwards. Have you tried to look your signals with an application on a smartphone to see what looks like the level? Try to stay on the 1, 6 or 11 as those who are not overlapping channels. Also set the bandwidth of 20 mhz as that gives you a helping hand.

• DDNS and UPnP problems on camera WVC80N

  For weeks, I had problems with the two things I mentioned in the subject field. I talked to a high level Tech Support of Linksys Sunday, but she has disabled my my UPnP on my router, although does not happen because if I do that then I might as well get rid of my account TZO, which happens next month if I renewed it. I keep getting error messages, it is both of my cameras WVC80N but now it's only on one of them. The message says the DDNS: impossible to get a current public IP address some of this, but a lot of this UPnP: Internet gateway UPnP discovery failure. I have a WRT160N V3 router, it still registers on the motion, but if the UPnP problem keeps it can't save when the problem occurs. I have TimeWarner cable, may be the problem with them?

  I did everything last night around 17:42, and so far it has worked for more than 24 hours. Top Tech support told me this Sunday, but on the router, he wanted me to turn off UPnP I told her that I couldn't do because I wouldn't be able to log in to my account TZO if I turn it off. But all the other things he said to me you also told me to do and the wizard said for me to do. As I said for more than 24 hours. now, it seems to work

  Thank you guys

  I think my problems just DDNS might be with TZO

• WRT610N problem with Archos 5 UPnP

  I have a WRT610N V2 router with the latest firmware available from Linksys. When the Archos tries to access my media server, the Archos device restarts. I tried my wag160n existing as a point of access to information and the archos works very well. I also tested the Archos on a different network and it works very well.

  Everyone knows about this problem with the WRT610N? I have eliminated all other components on my network and the router seems to be the cause of the problem.

  Try to change the Mode of network in BG only on the router and then also check by disabling UPnP on the router... Check out this link for Archos.

• EA6900 DHCP timeout problem

  This is by far the stronger and more sophisticated wireless router that I have ever used, but it has a small problem in providing wireless services on my phone.  I looked through all the settings and read all the troubleshooting assistance, and I can't find which could control the router sending a momentary power switch pulse exactly all the 60 minutes that is picked up by one of my Apps (AutomateItPro) phone...

  I have had no problem affecting this router upward, mosty plain vanilla right out of the box.  Because I use a cable broadband ISP (Charter) I use DHCP - so I don't get in other internet protocoal settings that control "Connect on Demand", etc..  Nor was I changed the default maximum, length of lease of customer value in the configuration of the router, it's always 1440 minutes (24 hours).

  This app on my phone has the value triggers a notification when I disconnect all WiFi (this router provides my WiFi at home but I have the app to the WiFi network of any) and activate the mobile data and vice versa with a different tone.  With precision every 60 minutes since I have hard reset the router (with an unplugged power cable), I get a notification of your momentary loss of WiFi follwed in 2 seconds by restoring the WiFi.  I tried a hard reset twice and it is a signal on the router, not the app, or my phone.  The problem is that this continues to happen at night when I am sleeping, and this powerful application overrides my silent nights for the phone settings, so I can still hear him.

  What is the setting that does this on the router, and it is possible to prevent him from doing this (emission of the momentary power pulse of the wireless signal)?  I haven't checked if it is a reassignment of IP addresses at this time also...  I really like this router, but being awake is a pain...  (Yes there are other solutions of circumvention of the APP, but those who are not as reliable I found like stop this problem at the source of the router if possible.)

  Thanks from a newbie!

  Hey Ronald,.

  I used to have the same problem.

  The way I fixed it changed the name of one of my networks.

  This router is dual band and has a band of 5 GHz and 2.4 GHz band.

  I had both my SSID network named the same thing with the same password.  For a reason which is that... my connection would constantly.  After changing the name and password of one of the bands I have over this problem.

  Hope that helps Ronald.

  I know it's really annoying.

• Problems with a printer via wireles router two laptops, test message says not UPnP supported 0 x 80070035.

  Have checked all resorcess so far, error message microsoft search bar after kodak printer has 0 x 80070035

  Hello

  • What is the full error message that you receive?
  • What were the changes made before the problem occurred?

  You can view these methods:

  Method 1:

  I suggest you to disable any program of security on your computer and check if it solves the problem.
  After reviewing the question you must reactivate the security on your computer program.
  Note: Run the computer without antivirus software or firewall is a potential threat to the computer; Be sure to activate security software after completing the troubleshooting steps and after identifying the problem.

  Method 2:

  Alternatively, you can try to uninstall the Kodak drivers and reinstall it and check.

  http://Windows.Microsoft.com/en-us/Windows-Vista/uninstall-or-change-a-program

  http://Windows.Microsoft.com/en-us/Windows-Vista/install-a-program

  See also:

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

• Port forwarding does not work on EA6900

  Please help me to know what is the reason for this port forwarding does not work on my Linksys router:

  Model: EA6900 v1.1
  Firmware version: 1.1.42.161129

  I've set up two ports: TCP 22 and 8070 TCP to 192.168.1.10. (192.168.1.10 is up and running, I can reach the LAN ports).

  Yesterday, I had a live chat with Linksys support we tried to re - download the firmware even, but that did not help. Then factory reset and reconfigure the router did not help either.

  Unchecking "Filter anonymous Internet requests" and disable uPNP didn't help either (they have been suggested in similar topics).

  However, the IP displayed tab troubleshooting/Diagnostics reflect my external IP address (the IP displayed by http://whatismyip.com), which is weird, because I never have IP from my ISP from 100, that is displayed on the Diagnostics tab. So I guess it's a fake display or it relates to access to my router via www.linksyssamrtwifi.com ?

  Anyway I tried the two IPs from the outside, but the transfer simply doesn't work. (It works fine when I use my old router TP-Link).

  Please advise!

  Sorry guys, it seems indeed a double NAT problem. My ISP can detected MAC address change when I started using EA6900 (thinking that I couldn't not need public IP?) and since then he sends me IPs for NAT - ed. It is strange that the same day, he was working with my old router, but now it is even not working with my old router and not even working when I connect directly to my windows PC to my ISP (via PPPoE). I called their support line and they said that they will solve this problem within 72 hours. In any case, thanks for your help!

• Homekit with the iPad as hub problem

  Hello

  I just installed iOS 10 on my iPhone 6 and iPad 2 Air and try to play with HomeKit to remotely control lights of the hue.

  I can control accessories from my iPhone and my iPad, when both are connected to my Wifi network.

  I install my iPad as a Hub HomeKit via settings/Home.

  My iPad is well detected as HomeKit hub on my iPhone by the host application.

  The problem is when I switch off my iPhone from my Wifi network and connect through 4 G: I can no longer control accessories: my iPad is still considered homeKit Hub from my iPhone, but I get failures when trying to turn on the lights/out.

  I disconnected my iPad iCloud account and reconnected (same account iCloud on my iPhone).

  I've disabled iCloud/HomeKit and reactivated it on my iPad.

  I've disabled host/Hub and reactivated it on my iPad.

  I restarted my iPhone and my iPad.

  Checking with 2 factors is enabled on my account.

  I deactivated and reactivated the iCloud keychain.

  I plugged my iPad to a charger.

  Without success, any idea?

  Could it be associated with my case ADSL settings (UPnP is enabled)?

  Thank you.

  Good news: I removed my house in Homekit and created a new one from scratch: it works fine now.

  Thank you.

• Problem with SlingTV through Airport Extreme?

  I have a Motorola SB6141 cable modem, internet of Time Warner and an Apple Airport Extreme Base Station (later) for my setup. While SlingTV is not a great service, it was $ 20 a month and gave me what I need and has been much better than that Time Warner was in charge me for the same channels.

  Despite the problems of freezing SlingTVs or what not, for a while it worked. But one day a few months back it just stopped working. When you open the app, it either does not open or just turns and turns to be forgotten and never access the content. But if I try on my phone (Verizon LTE), or another network outside my apartment with the iPad or computer laptop, it works. So at home, I tried to go directly from the cable modem and right in the Apple TV (previously an Xbox) and when I do that it works. So really what it boils down to, is my Apple Airport Extreme Base Station router. If I'm either directly connected to the Airport Extreme Base Station (Apple TV ethernet to the router), it will not work, or if I use WiFi via the Apple Airport Extreme Base Station it will not work. But directly to the modem cable or on any network outside of my home, the service works.

  So in short, something about setting up Apple isn't allowing the Sling TV app to open or work on any device. I even did a rest of the plant and installing my Apple router once again, and the same problem persists.

  FYI - I use Netflix, Amazon Prime, Hulu and all the Apple TV, TV shows, rental movies and content without ever having a problem with opening or streaming. This only happens with SlingTV when you try to access content on any device (iPad, Apple TV, Xbox One, iPhone, Macbook Air) via WiFi or Ethernet via Apple Airport Extreme.

  I tried to provide all the little details that I could. If someone could please provide a solution I would really really appreciate it! Thank you.

  Well first of all try to port forwarding. Slingbox I guess would use a similar to SlingTV montage... Unfortunately when I google for it I see just people having so many questions like you... no rigging, no answer they give up.

  http://PortForward.com/English/routers/port_forwarding/Apple/AirPortExtreme/Slin gBox.htm

  It is the old airport of model, but the idea is correct.

  If you still have questions... There is a major problem... port 5001 is used by the airport for its installation...

  If I run a scan of port of network utility, that you will find that it is already used.

  Port scan started...

  Host port scan: 192.168.2.201

  Open TCP Port: 5001 commplex-link

  Open TCP Port: 5009 winfs

  Port scan has completed...

  My recommendation is to replace the airport as your main router... Something good market like the C5 TP-Link or the WR1043ND which is less than $50US. These routers use UPNP is missing on the airport. Continue to use the airport for your customers to apple as WAP and switch.

  BTW: this is no bad thing because you also have a known problematic modem... SB6121 and SB6141 have major problems... do a quick search and you can find a lot of posts about this.

  TWC has also now use IPv6... that can ruin.

  See the instructions for installation (same as comcast for TWC).

  http://mydeviceinfo.Xfinity.com/download.php?file_id=35

• R7000 problems play 2 ps4s all same same game party

  Hello

  We recently bought the nighthawk R7000 router running firmware version V1.0.7.2 2.4.24 and filled our gateway 2wire ISPS router (ISP said it was the only way to connect and use a new router) to it and put it up for all the devices in our House. Now, before we bought the nighthawk we had no problem playing together, but with the recent purchase of an android minix neo u1 area, we wanted a better smart router. So husband and I started to play fate with some friends and played for less than an hour when all of a sudden the ps4, I was using completely out me. I restarted the ps4 and returned joined and started to play only to be deported again. The next time I'm on, I was unable to get to my husband and he couldn't join me. I looked online for solutions and went into the settings of routers. I checked and UPNP is already enabled and I have reset the QoS settings to the factory think because I had activated the QOS to prioritize the two different ports that have been using the ps4s that could be the problem. I have you will also know the two ps4s are wired in and I don't know offhand speed but we have improved our internet package for a better service and wirelessley is the speed upload 1.97Mbps and the download is 24.76Mbps so wired should be faster than that. If anyone knows what I can do to get the two ps4s running smoothly play together to the common Nighthawk? Thanks in advance

  Thanks for your response James. With a little help from netgear support and looking for a little me. We found our best option was to enable UPnP, enable IPC now that ps4 support and remove rules that I had set the port forwarding. Now, we can play set and have the children watching Netflix or streaming media in multiple areas of the House with no problems at all!

• Satellite 510 - Wlan upnp sharing question

  Hello

  I have a Sat 510 Windows 7, I connect to my network through a wireless access point.
  Everything seems to work except upnp sharing from my laptop which does not recognize some devices, same XBOX360 connect / even though I can see it on the network.

  When I connect wired, sharing upnp works very well.
  I have an XP machine alongside and with no problems or wireless, both machines are running the same norton firewall.

  I tried everything I can think but do not know if it is a framework for Win 7 or fault or a hardware problem with point of access or Toshiba.

  See you soon

  Hello

  To be honest, I've never heard of upnp sharing but to use special ports, allow the latter in your router configuration and firewall software (Norton).
  Check it!

  In addition, I would recommend updating the firmware on your router and install the last driver WLAN.
  Also check the network on Windows 7 configuration!

• R7000: UPNP Renderer not visible when connected via WiFi

  Hi all

  I use the R7000 as a router and I have the problem that my UPNP renderer (Denon DNP-F109) is not visible if connected via WiFi (via Ethernet, everything works very well).

  Can someone give me a clue what to do here?

  I went on DHCP and UPNP in the configuration. All UPNP (Server/converter/controller) devices are in the same 192.168. * network.

  Thank you very much

  Stefan

  Hello Stefan,

  Please perform a reset of the device and check again if still the same problem.

• I need to configure UPnP to get a better connection for Xbox live

  I need to implement UPnP to get a better connection to xbox live. could someone help or tell me how to activate it?

  XBox - Contact us (support)
  http://support.Xbox.com/en-us/contact-us

  XBox - Support Forums - and my XBox (top-right)
  http://forums.Xbox.com/

  Xbox technical support phone number

  • Toll-free: (800) 4MY-XBOX or (800) 469-9269

  Opening hours: 600 PM 2200 h / Pacific / daily

  International (direct line in the U.S.): 425-635-7180

  XBox LIVE - Service status
  http://support.Xbox.com/en-us/Xbox-Live-status

  Manage the XBox Live account
  http://support.Xbox.com/en-us/billing-and-subscriptions/account-management/Xbox-Live-account-management

  XBox Live Sign-in problems
  http://support.Xbox.com/en-us/billing-and-subscriptions/Windows-Live-ID/Xbox-Live-sign-in

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Help with major security problem if you please. Internet gateway?

  Hello

  After a few weeks of scratches all about untangle sceurity perceived a few questions with email etc. - yesterday I belive I discovered a big problem and need some help please.

  I hope that I write from own machine because I believe that desktop home computers are compromised.

  Main PC is running XP and has a connection via a cable ethernet via a bt Home Hub2.

  Yetsrday while watching my network connections I noticed something called "Internet GATEWAY" above my LAN icon.

  It showed that I had been connected for over 2 days (a little more than 2 hours for the LAN) even when the PC off and was send/receive many packages and seemed much faster than my LAN. problem: I click on this & it won't let me log out or see properties / settings - I get a warning about 'connection is currently unavailable '... I really worry that it is someone else on my PC - is this right? How can I fix it? and it is a matter for the Police.? I'm really worried. Other symptoms, I noticed - my windows log on 'his' dissapraed a & in the event Manager-, there is no security - only since 2006 newspaper.  Very slow PC. Running SuperAntispyware - no problem after removing a Security Center option turn off a few days ago.  Really gratfeul l to help guys. Am at my wits end. Very garteful using anyones.  I guess that my internet connection and PC was hacked/compromised.

  To be clear, you remove all networking services, but just the part that detects and controls "gateways" as your router.  This removes the "Internet gateway" of network connections icon, but should not do something else.

  If a right click or double click on the "Internet gateway" just produced a message "connection is busy", which makes me think that something is not configured correctly - either the router (bt Home Hub) has turned off UPnP (or does not really support) or the UPnP in network services service is not installed, or something else.

  I don't think that someone else is controlling your connection, but as I said, the other symptoms you describe indicate a malware problem continues and you need to take steps to ensure that your machine is free from malware.

• I ran fix it 50015 to task bar icon not apperaing it fix the problem at the time of the e but next time, I rebooted I had to restart the program. What is permitted to fix.

  My icon disappear for task bar I ran fix it it 50015 it solved the problem. But when I reboot I have to run the patch again. What is permitted to fix

  The problem is resolved.  First of all, I ran hard he 50015 then turned off upnp and ssdp. It works now.

  Thank you, Glenn