USB 3 material

Similar Questions

• using 6341 USB frequency generation device but level is droped when conect

  I use the DAQ USB-6341 material for frequency generation. The desired frequency is generated correctly but when I connect to any other device, the voltage level, I mean that the peak to peak of the frequency voltage has dropped to 0.6, 1 Volt and also the frequency has varied. I unplug the charge or unit frequency becomes constant and peak-to-peak voltage becomes 5.

  Please some help me solve my problem.

  Thank you

  Best regards

  Naseeb

  
  

• Error of Driver GPIB-USB-HS - 10 possibly after Feb Windows Update Windows

  Starting from 17/02/2016, GPIB-USB-HS material (2) is no longer connecting on 10 of Windows using NI488.2 Rev 15 15/8 with the 15.0.1 patch.

  Using VMWare player 7.1.3, the VM sees the material, connects, turn lights and then turn off. The virtual machine shows "Driver error" unable to connect to the USB device. This has been tested with two USB devices that have worked with the same setup for a few years now on Windows 7, 8, 8.1 and 10 using VMate 7.x and 12. xs

  Possibly this is related to the last update of Windows,

  Repair, or a full installation of rev 15 NI488.2 solves this problem.

  VISA still works via TCP/IP.

  Any thoughts will be greatly appreciated.

  Update: the pilot is still alive.

  The latest version of Windows, which has been applied to the host system 05/03/2016, restores the driver under the guest virtual machine feature. Revisions to operating system host and client are now at 10586.122.

• OR USB-6009 daq sample following loss, while the loop iteration

  Hello

  I am trying to acquire and display data measured from a DAQ NI USB-6009 material using Labview 2015. I am using the wizard daq defined for the differential mode and n samples with the sample rate and the total number of samples registration by the user. My problem is that when the specified amount of samples is acquired and the while loop continues to the next iteration, some samples are removed (I know because I tested it acquire a wave of fishing and there is a noticeable artifact in the signal at times where the while loops - I downloaded a file showing this artifact in a wave of fishing that was recorded with a sample rate of 1000 Hz 500 samples of recording each) iteration which means that the artifact occurs every half second).

  I think that this can be corrected by simply taking off the while loop daq assistant and specifying the number of samples you want the entire test to acquire. However, I would like to see the signal in a graph as its achievements and the daq can acquire data indefinitely until the user presses the stop which, to my knowledge, it would take a while looping. I downloaded my vi for reference, and any help would be greatly appreciated!

  Set your Acqisition Mode on "samples continues."

  N samples: reads the desired number of samples and stops.  Will read once again what DAQ Assistant is represented.  In other words, that there is a gap of time between readings.

  Continuous samples: data acquisition just constantly reads the data.  The DAQ Assistant just gets the number of requested samples and data acquisition keeps just read and store it in the buffer.

• Why USB-6501 does not install on Win7?

  We are in a process of migration of the old XP machine test system to the new system of Win7. All but got properly installed USB-6501. After you install LabView / DAQmx and connection USB-6501 windows could not find the drivers for this device (poster the exclamation sign on the icon of the device in devices and printers). MAX 4.7.4 detects either of the device. I looked for similar scenarios on the Forum OR and abroad and tried the solutions proposed. Nothing worked for me. I know the issue isn't with the USB-6501 material because it is functional on the old system. 4.7.4 MAXLE Win7 system detects a very well (GPIB-USB-HS) different USB device, but not for USB-6501.

  I hope someone can help us identify the problem that we have struggled with for some time. Here are the differences between shipments of software on two systems:

  Old system:

  OS - XP SP3

  LabView - 7.0

  DAQmx - 8.0

  VISA - 4.4.1

  MAX - 4.5 (detects the GPIB-USB-HS and USB-6501.) Status on 6501 LIGHT flashes continuously)

  New system:

  OS - Win 7 Enterprise

  LabView - 7.0

  DAQmx - 9.2.2

  VISA - 5.0.3

  MAX - 4.7.4 (detects only GPIB-USB-HS. Status on 6501 LIGHT flashes 3 times and then road)

  Germano,

  The device has been appear in Manager devices, but with the yellow exclamation mark for no drivers found/expenses. Update drivers on the property page does not help.

  So yesterday I spent most of the day removing all facilities OR according to the instructions, I found in this forum. Then I reinstalled the software OR in the order following, restarting after each installed:

  (1) LabView 7.0

  (2) DAQ 8.0.1

  (3) NEITHER-488. 2 (v2.30)

  (4) connected USB-6501 first. The installation of the device has gone well and is now detected to the MAX!

  (5) connected GPIB-USB-HS. Scanned for changes on the hardware, peripheral GPIB presents itself to the MAX, but with a weird name announcement its INF file on his behalf. See the screenshots below:

  GPIB device incorrectly installed:

  

  GPIB device properly installed:

  

  The strange thing is that this GPIB device was fully functional on my previous installation (see attachment max_report_3-23 - 11.pdf), now reinstall after its unusable (see attached max_report_3-24 - 11.pdf). Looking for GPIB instruments to help Max returns no result, but if I reconnect GPIB-USB-HS to the old system of PC all instruments are detected (for instrument scan error message see attached MAX after reinstall.jpg).

  That my new problem is not related to USB-6501, maybe I should open a new forum thread.

• FBus Monitor may not work with Configurator at the same time

  I am using NI USB-8486 material and I can get Fbus Configurator work on it. But whenever I run the FBus monitor, the Configurator will go wrong. (Device on the Fbus become invalid)

  I checked the Configuration OR-FBUS Interface utility, I have seen that the use of the port can be either OR-FBUS or Bus-monitor.  Since the USB-8486 only has a port, it means we can only support a single application (Configurator or monitor), instead of two at the same time?

  I'd appreciate any help!

  Hi Steve,.

  That's correct - USB-8486 can function as an interface device or monitor buses at the same time, and the role is configured in intensive care.

  If you want to have two roles at the same time work, you will need two NICs installed.

• Control valve tank with plots and twists of the water

  Hello everyone!

  This is my frist real project. And I am in love with this program so far!
  I have a little problem. Here it goes:

  The project of the University which has been given to us is to simulate a (entrance OPEN/CLOSED valve) water tank filling and emptying (output range of 0 to 100% valve), but with a few twists. It is done by the command to the movement by the following formula: flow rate [%] = position of the valve [%] * current water height [%]. (The output valve takes values in percentage from 0 to 100% giving the voltage digital output of 0 volt to closed(0%) or 5 volumes for open(100%), the strange part, is that the digital output can have a value of 0 or 1, so the position of the valve is "simulated".) And the supply valve (valve entrance) water can be open or closed (if 0 or 5 volts)

  -Sequences cannot be used (only one for initialization and cleanup can be used)

  -When the water level reaches 10% of the max height, LED lights, the output valve closes and the input valve opens. The LED is on until the button is pressed. The output valve cannot be opened until the water height is greater than 50%.

  -When the water level reaches 90% of the max height, LED lights, the entrance valve opens. The LED is on until the button is pressed. The output valve cannot be opened until water height is less than 50%.

  -There are two mode selectios:

  Control by hand: the person sets the position of the valve in percent and the flow is calculated by the formula and displays on the screen.

  Automated: Every 2 seconds the program assigns the place valve so that the current is constant, it is the value by the person.

  -(N'ont pas gottern ici encore) ESD (Emergency shutdown switch) the when is pressed both the entry and exit valves are closed. The entrance valve cannot be oppened up to the RESET_IN key. If the program is 'Control in manual mode' output valve cannot be opened until the RESET_OUT touches. In which case the output valve is in "Auto" mode, it does not start work until the RESET_OUT touches.

  My main problem here is the fact, I cannot use sequences and nested, then the loops do not work. The aqusition of data stops until the inner circle loop ends and I need both work. Especially for the 50% rule.

  I've been hitting my head for a few days and still couldn't come up with a solution.

  I have attached the VI.

  Tips are welcome!

  For the time being the outputs inputs/digital analogue are a simulation (when the time comes the USB-6008 material is used).

  There is some things that confuse me (as if the valves are percentage, from 0 to 100%, or digital, 0 or 1), but regardless, it's a detail.

  Review the task and consider what you want to do and that the "States" the system may be in.  [This with a pencil and paper, do not open LabVIEW yet...].  The description of your problem learn you something about the transition from one State to another.  Here is a thought exercise:

  Suppose you are in a "State".  Let the system to "do its thing" for a second, which could involve the water flow.  At the end of the second re - evaluate your state - it changed?  Continue to do this...

  This model of 'something' is called a State Machine and LabVIEW has some very good examples and tutorials on the creation and use.  The important things to do before you make your coding is (with the pencil and paper) decide on your statements, decide on the transition rules, and then you are ready to code.

  There are different ways to build a State Machine in LabVIEW, but the basic idea is quite awhile (to keep things moving along, a shift register which includes the current state, usually represented as an enumerated, Type whose values are simply the names of your States (made for a very mnemonic routine) and a Case statement whose power is the State of the shift register that contains the code to achieve this) particular State of loop, including the implementation of transitional rules (which can cause a new State on the registry to lag when it comes out of the investigation of the case).

  A great exercise.  Strive to keep your block diagram on a single computer screen by making use of the screw subgroup chore (as the management of changes in the water level based on the current water level and "States" (which here means 'values') two valves).  Once you understand the 'Idea' State Machine, you should be able to write the code for this problem quite easily.

  Bob Schor

• How to get a file created by windows labview to work on a mac

  I try to open a data acquisition simple vi which was written in Labview 2009 for Windows, using the USB 6211 material. I installed Labview 2010 for Mac OS X (full) with NIDAQMX-Basic for Mac. The problem is that none of the sub - vi DAQMX opens correctly. I think it's because they have different names, for example in windows labview "DAQmx create Channel ' becomes 'DAQMXbase create a channel' or something like that. What is the problem? Installed the wrong DAQMX for Mac OS X?

  Hello oilyfingers,

  As other users have posted, DAQmx Base and DAQmx are two different drivers.  It is recommended that Windows users install DAQmx on their PC.  However, a version of DAQmx Base also exists for the Windows environment.  Your VI is expected to require fewer changes after installing this driver.

  NEITHER DAQmx Base 3.4: http://joule.ni.com/nidu/cds/view/p/id/2126/lang/en

  If you do not want to install DAQmx Base on Windows PC, it is a conversion utility that should help to automate the conversion of your VI of DAQmx Base DAQmx code.  This can be found in the link below:

  Conversion utility: http://joule.ni.com/nidu/cds/view/p/id/446/lang/en

  Smercurio_fc suggested, submit your interest for and day DAQmx version of Mac OS X in the exchange of ideas.  User in LabVIEW 2010, more than 10 different proposals implemented in the exchange of ideas.

  Kind regards

• NOR-488. 2 drivers for Windows 7 Starter Edition

  I was hoping to control a potentiostat (BY 273 (a) with the GPIB USB HD material. In general, I do with a desktop running Windows XP and have no problem, but I recently bought a netbook (which is running Windows7 Starter Edition) for portability. I was hoping to install the proper drivers - but it seems that v2.7.3 does not support the Starter Edition. Is it possible to make this work? Thank you.

  Have you tried this?

• Satellite A100 - material cannot be found via USB

  Hello all,.

  First I want to apologize for my bad English following (I am from the Germany).

  I have my laptop for about two years. All my USB hardware worked.
  But about a week ago, I tried to save data on my USB but my laptop could not match it.

  There was just the message: "no known material. Installation was not correct. »
  The effect is: I see the USB in the Solution Explorer, but when I open the file there is no datas (but the USB was not data always full).

  Now I can not plug anything into the USB socket.
  No USB, no camera box, no external hard drive.

  There is no difference between these things, windows still shows the same message of failure...

  Can someone help me please? I think there must be a pilot unit failure, but why he is one day to the next?
  Thank you for your help (and willingness to try to understand my English ;)).

  First of all, I must say that your English is not bad!

  Now a few words about your question.
  Try this;
  -Disconnect all USB devices
  -go to the Device Manager
  -remove all USB ports, controllers
  -restart the laptop

  After restarting again the windows should recognize the new hardware and needs to be reinstalled all USB ports.
  Then check again if you use USB devices.

• I installed the of Vernier SensorDAQ (NOR-DAQmx 8.6), the USB driver seems to load, but the material is not accessible

  I have several versions of Labview (Windows 7), 8 and 9. I installed the SensorDAQ under Labview 8. The VI does not recoginize the acquisition of data and the utility OR of measurement and automation is not the acquisition of data, or the other. The dirver NOR appear to be installed (Device Manager). The light on the acquisition of data is flashing which is supposed to indicate that it works. Suggesttions?

  Hello Syncrec,

  Please use the forums of NOR.  What USB DAQ device you use and which driver you have?  "You can find the driver in opening measurement and Automation Explorer (MAX) and looking under my system" software.  In addition, you said your device appears in the Device Manager, but what makes it say when you right click on your device and select Properties (looking for a message that says that the device is functioning properly)?  Finally, you use the Windows 7 starter edition or the full blown?

  Kind regards

• expensive material: problems puts het installeren van usb op laptop voor fietsprogramma key.

  ALS ik mijn usb van mijn fiets roles key in to portable USB stick niet geinstalleerd worden kan steekt. ER komt you Haag: stuurprogramma kan niet geinstalleerd worden. Wat kan ik doen hieraan?

  Hello

  Please select your language from the drop-down menu above to post your question in the language of your choice. The forum in which you've posted is for English only. If you can't find your language above, support for additional international sites options are by following the link below:

  http://support.Microsoft.com/common/international.aspx

• Why any material I install using a USB port cause my computer access to the screen asking how I want my computer restarts in safe mode, safe mode with network etc.

  I USE WINDOWS XP PROFESSIONAL

  Hello

  1. don't you make changes to the computer until the problem occurred?

  I suggest you to try the steps below and check if it helps.

  Method 1: Try running the Fixit tool from the link below.

  Hardware devices do not work or are not detected in Windows:
  http://support.Microsoft.com/GP/hardware_device_problems

  Method 2: Try also to update the latest drivers for your USB using the link below.

  How to manage devices in Windows XP:

  http://support.Microsoft.com/kb/283658

  Method 3:

  Advanced troubleshooting tips for General USB for Windows XP problems: http://support.microsoft.com/?kbid=310575

  Hope this information is useful.

• USB does not recognize not material

  I had to uninstall a printer I use, and now when I try to reinstall, my computer can not say it is connected. At the same time, my computer has ceased to recognize other devices like my Iphone and I touch are connected.

  Hello

  Check the configuration/settings (BIOS/CMOS) often F2 when you start - make sure that USB is enabled.

  If a PC and if necessary the embedded USB can be disabled and a USB card can be used only
  is not expensive. For a laptop, using a real computer shop (no leeks and glances at a Best Buy
  or other stores) or system manufacturer support.

  ------------------

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -----------------------------------------------

  Then lets refresh the USB stack

  Control the click Control Panel - Device Manager - no matter where in the box of white/white - then the VIEW - see the
  Devices disabled - look around (with the exception of USB controllers) for your devices (can have
  zero or more than one) and top - right click UNINSTALL.

  Control Panel - right CLICK on EVERYTHING - Serial USB controllers - Device Manager and UNINSTALL
  all except the category itself - REBOOT - it refreshes the drive and battery USB

  This KB shows XP how to and the method of Vista is identical
  http://support.Microsoft.com/kb/310575

  This is a utility to help you, but do 1 above.

  USBDeview is a small utility that lists all USB devices currently connected to your computer, thus
  as all USB devices that you previously used. Run Options and check the 1st three choices to see to it there
  Is there.

  http://www.NirSoft.NET/utils/usb_devices_view.html

  You must remove all instances of the devices and restart.

  ----------------------------------------------

  If necessary try these two:

  Tips for solving problems of USB devices - and a Mr Fixit
  http://windowshelp.Microsoft.com/Windows/en-us/help/c39bd203-f729-47a4-8351-83291e13c8a81033.mspx#EGB

  Hardware devices not detected or not working - Mr. Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Problem of USB ports: remove the material does not work. It works on different computers for the same USB devices

  Original title: problem of USB ports:

  I have a computer dell laptop inspiron d1420 provided with Windows vista and I have upgraded to Windows 7 ultimate, I noticed that when I plug in a USB mass storage, when I try to remove it, I don't get the safe delete the message and lately when I try to remove it, I keep getting the message He's busy and I can't remove it. I tried the same USB on another PC and I have no problem at all. I connected a printer, USB cable and wondows llok have not the driver or didn't install the printer, he left as a device not specified with the name of the printer, but I can't print. I tried with another PC that is also running Windows 7 ultimate and I have no problem, windows has installed the driver, because I used the same printer and the same cable. What is the problem with my USB 4 ports and how to fix?

  Hello

  When you get this message while trying to remove a USB, it's basically a lock for this USB device by some process running on the computer. If we know which process is this locking mechanism, we could also find which Service is associated with this problem in the computer.

  To check this, you can use a program called Process Explorer. You can download this program from the following link. Once downloaded, extract the contents of the zip downloaded to a folder on your desktop. Inside this folder, you will see a file by the name of procexp , which is the executable for Process Explorer. The download link is:

  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896653

  First, plug the USB to one of the USB ports. Then, once you have the executable to Process Explorer, right-click on it and then click run as administrator. Please allow all guests UAC can occur. Once the Process Explorer is running, please follow these steps to search for processes using the USB at the moment:

  1. click on Searchand then click on manage to find them or DLL on the options menu at the top.

  2. then in the pop - up which will turn up next, type the drive letter for the USB drive connected to the computer (for example G: or H:) right now and click on Search.

  3. he should then display all instances of the process that is using this USB at the moment with the corresponding process ID (PID).

  Now, once you have the names of processes using the USB at this time, you can terminate them by clicking on them and then clicking on Manage close. Once this is done, you should be able to eject the USB safely.

  I would like to ask the names of processes lock the drive in your computer. This should give us an idea of what we might have to take the next.

  In addition, for the other issue that you mentioned, in which the computer does not automatically and correctly detects the printer when it is connected to the computer, I suggest you to check whether or not your computer Plug-and-Play service is set to automatic. Here's how you can do this:

  1. press the Windows and the R on your keyboard to get to the top of the run box.

  2. type Services.msc in the run box and press enter on the keyboard. Allow all UAC prompts that may coming up next.

  3. once it opens the window of the Services for you, scroll down to the Plug-and-Play service and double-click it.

  4. in the properties box that will come next, the Startup type should be set to Auto and the Status of the Service must be started. If this isn't the case, please put these values.

  5. click on apply then OK, close all windows in the computer and restart the computer once.

  Once these steps was performed, please check if the problem remains the same. We know the results.

  I hope that these steps raises you in the right direction in order to solve this problem. Don't answer if you still need assistance, we will be happy to be of assistance.